Ubisense America MOD30 Location Tracking Tag User Manual Intrinsically Safe Tag

Ubisense Limited Location Tracking Tag Intrinsically Safe Tag

User Manual

Copyright © 2014 Ubisense Limited, All Rights Reserved Wideband Location System Modular Ubitag V3.0 User’s Manual Written By Andy Ward Ubisense Limited St Andrew’s House St Andrew’s Road Chesterton Cambridge CB4 1DL ENGLAND Tel: +44 (0)1223 535 170 Fax: +44 (0)1223 535 167 Email: support@ubisense.net WWW: http://www.ubisense.net/ Released: January 2014
Copyright © 2014 Ubisense Limited, All Rights Reserved Table of Contents Introduction ...................................................................................................................................... 1 Regulatory Information for the United States of America ................................................................ 1 Modular Ubitag V3.0 Specifications ................................................................................................ 3 Integration information ..................................................................................................................... 4
1 Ubisense –Wideband Location System – Modular Ubitag V3.0 Introduction The Modular Ubitag V3.0 is a wireless module intended to be integrated into other devices for the real-time location of objects. It transmits wideband pulses which are picked up by a network of basestations (Ubisensors), allowing the 3D position of the tag to be found. The use of wideband technology enables greater positioning accuracy within buildings than other wireless technologies, because it is much less susceptible to multipath interference effects. Applications of the system include healthcare, workplace productivity, security, retail management and manufacturing. This document describes the features and specifications of the Modular Ubitag and important regulatory information concerning its use and integration into other devices. Regulatory Information for the United States of America The Modular Ubitag V3.0 is approved under Parts 15.249 and 15.250 of the FCC rules as a Modular Transmitter. The product into which the Modular Ubitag V3.0 is incorporated must bear a label per the FCC requirements which shows the FCC ID assigned to the Modular Ubitag V3.0 as follows. Contains FCC ID: SEAMOD30 The following information must be conveyed in the information supplied to the End User of the product into which the Modular Ubitag V3.0 is incorporated: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user’s manual or instruction manual shall caution the user that changes or modifications to the equipment not expressly approved by the party responsible for the grant of equipment authorization issued by the FCC could void the user’s authority to operate the equipment under the grant of equipment authorization, for example: CAUTION: Any changes or modifications made to the Modular Ubitag V3.0 which are not expressly approved by the Ubisense Limited could void the user's authority to operate the equipment.
2 Ubisense –Wideband Location System – Modular Ubitag V3.0 Regulatory Information for Europe Hereby, Ubisense declares that this Modular Ubitag V3.0 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity for this equipment may be obtained from: Ubisense St. Andrew's House St. Andrews Road Chesterton Cambridge CB4 1DL United Kingdom This UWB transmitter must not be installed at a fixed outdoor location or used in flying models, aircraft and other forms of aviation. Integrators should note that when the module is integrated into other equipment the combined device must meet all essential requirements and other relevant provisions of European Directives for that combined equipment. See ETSI TR102070-1 and ETSI TR102070-2 for further details. Regulatory Information for Canada The Modular Ubitag V3.0 is approved under Industry Canada documents RSS-GEN, RSS-210 and RSS-220 as a Modular Transmitter. The product into which the Modular Ubitag V3.0 is incorporated must bear a label per Industry Canada requirements which shows the Industry Canada ID assigned to the Modular Ubitag V3.0 as follows. Contains IC: 8673A-MOD30 The following information must be conveyed in the information supplied to the End User of the product into which the Modular Ubitag V3.0 is incorporated: Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
3 Ubisense –Wideband Location System – Modular Ubitag V3.0 Modular Ubitag V3.0 Specifications Wideband transmitter section Operates under: FCC Part 15.250 Industry Canada RSS-220 ETSI EN 302500 Centre frequency: 6.416GHz -10dB bandwidth: 0.739GHz Conventional 2.4GHz radio transceiver Operates under: FCC Part 15.249 Industry Canada RSS-210 ETSI EN 300440 Lowest channel frequency: 2401.75MHz Highest channel frequency: 2481.75MHz General specifications Dimensions (WxHxD): 24.5mm x 24.5mm x 9mm Weight: 6g Power supply: 2.3V-5.25V DC supply Operating temperature range: -40ºC to +85ºC
4 Ubisense –Wideband Location System – Modular Ubitag V3.0 Integration information The dimensions of the module PCB are shown below: When mounting the tag on another device care must be taken to avoid occlusion of the antennas by tall components, shielding, or mounting screws. There should be an air gap of at least 1mm left around both of the antennas to avoid detuning. While the connector provides some mechanical fixing it is not recommended that this is the only fixing point. A double-sided pad has been supplied that can be fitted to the top of the screening can to securely fix the module to a PCB. When designing the PCB it is recommended that there is no ground plane underneath the module. Power should be supplied on the following pins of the header: 2.3V-5.25V DC power input: Pin 3 Ground: Pins 5,6,9,10,14,18,19 A number of pins on the module’s header may be used for digital input/output and analogue input. Note that application-specific use of these pins will require Ubisense to write modified firmware for the device, and therefore integrators wishing to make use of these features should contact Ubisense in the first instance. The header used on the module is a Major League TSHS-5 10-D-04-A-F-LF, a standard 1.27mm pitch through-hole pin header. The recommended connector to use with the module is: Connector: Major League LSSHS-5 10-D-06-F-TB-P-LF (SMD) Please refer to http://www.mlelectronics.com for further information and ordering details. 4.5mm3mm2.1mm1.6mm4.5mm3mm2.1mm1.6mm24.5mm24.5mm24.5mm24.5mm20mm20mmUbisense20mm20mmUbisense

Navigation menu