Uni Art Precise RS950-001R RF 900MHz Stereo Wireless Headphone System User Manual

Download:
Mirror Download [FCC.gov]
Document ID	85643
Application ID	tF5Yme376btKXwJx74KiCQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.94kB (174245 bits)
Date Submitted	2000-02-08 00:00:00
Date Available	2000-02-25 00:00:00
Creation Date	1999-08-27 18:07:55
Producing Software	Photoshop PDF Plug-in 1.0
Document Lastmod	1999-09-14 10:34:35
Document Title	User Manual
Document Creator	Photoshop PDF Plug-in 1.0

93951 + RSQSQHQSQQ
RF 900 MHz STEREO
WIRELESS HEADPHONE
SYSTEM WITH AUTO TUNING
OWner’s Manual
Please read before using this equipment
INTRODUCTION
The sooMHz slereo wireless headphone sytern with compact design
uses latesi wireless technology that enable you to enjoy music and
TV saund anywhere Inside or ouIsIde your home. You can simply
connect the system to any sound source such as CD. TV. VCR,
Hi-Fi and radio.
FEATURES
L 900 MHZ RF lechnulogy.
2, RF technology lets you 10am Iresly throughout your house.
3. Operating ulslanca up to 50 Meters.
4. No Iine-of»s|ghl limitation.
5. Rechargeable headphone recelver.
ill-in durger in the transmitter.
7‘ VirIuaIIy imenerenoe free stereo quauiiy.
B. ALC and auto ONIOFF wme
9. AUTO TUNING
TRANSMITTER
mums mmcnw (nan mm ommm. mummsan
mu. Awusr
6 ‘
fi—‘T I
mums mum mm mm cum
HEADPHONE RECEIVER
ow ocr swmm
INSTALLATION
TRANSMITTER
1. Screw In the antenna on the transmitter.
2. Connect the supplied AC power adapter to an electrical wall outlet
3. Plug the AC power adapter In the chackloceted on the rearct
lhe transmltter.
4. The rear at the tmnsmitter has one audlo cord that can be
connected to audlo output ledr (R & L) at TV, Hi-Fi, VCR, Radio
tape recorder or tn headphone / earphone jafik wllh the connector
palm/Med.
The green auto signal LED Indlcatorwlll be ON afteryou plug the
adapter In the AC outlet and connect me Audio Plug to the audie
source. When the auto on indicator is OFF. turn on and adjust your
audlo source output level until the green LED Indlcator light on input
level.
mm
mm:
cause I U
00m"
“‘°" ' avwl
Ammo
§m ........
HEADPHONE RECEIVER
1. Open the battery compartment cover on the rlght side 01 the
headphone receiver.
2. Insen lwu AAA slze rechargeahle battery with correct polarlty.
3. Cover lhe battery compartment.
amen Bonn
OPERATION
1‘ Turn on the audio source (TV or audio component) to which the
transmitter is connected.
2. Switch the ONIOFF switch on the headphone to ON.
3. Place the headphones on your head and adjust the volume control
to the desired listening level.
4. Press the Auto Tunlnu button 01 headphone until to the frequency
which is same as ttansmitter’s transmisson trequsncy for best
reception. The green LED WIII Ilght at this status
5. It the best ivequency reception is not hund, press the Auto Tunlng
button again to locate the trsqusncy at the transmitter tor the best
reception.
Note:
You should now be able to wak treely tram room to room wtthout
disruption. It disoruption should occur (signal breaks up), press Auto
Tuning button to maximize slew reception. If you hear interference
trom other components, re-adlust the irequency by pressing the Auto
Tuning button. You may have to try a tew locations to find one with no
Interference, Please refer following drawings A and B for best tunIng:
Keep a distance upto about 7 meters apart tram transmitter when
making tuning by Auto Tuning button on the headphone torbest
stereo reception.
emit
Whenever you find trequeney 1am. ie-adiust your tuning of
transmitter, and then press the Auto Tuning button 0! the
headphone to other tree location
X g
, \ , .
E? \é t__u‘
nu—
For protection oi the transmitter and save the power, the transmitter
will be cut oil automatically in about one minute when the Input signal
trorn audio source is too weak tor operation. In the other words, if the
signal recalls hack, the transmitter will work again automatically.
CHARGING THE BA'ITERIES
L Switch the ON/OFF switch on the headphone receiver to OFF.
2. Plug the charge output lack Into the charge input socket of the
headphone receiver to charge the batteries.
3. The charging process starts automatically when the batterles are
charged and the RED LED light up. Charge the new batteries for
24 hours prior to the first use or the headphone system
Caustion : Don't use other kind at battery to replace the rechargeable
(AAA) battery. When you are not usan the headphone
receiver, please switch it to OFF to avoid damage or
batteries.
as» ten
The battery pack must be fully charged prior to operation. An Initial
charge “24 hours is required to ensure the extended life oi the
rechargeable batteries. Be sure the headset is in the OFF position
during charge status,
SPECIFICATION
‘nansmlsslon Mode : UHF stereo
Carrler Frequency : 91145 - 913.5 MHz
Operation Vottaga : Transmitter. 12V 300m
2 Receiver, 24V (2 X AM rechargeable battery)
Frequency Response : 20Hz - 15KHz
Distortion : 1.5%
SIN ratio : 5063
Separation : 30:15
Operation distance : 50 M
“Operation is subject to the lotowing two conditions: (1) this device
may not cause lnterierence. and(2) mls device must accept any
interlerence, including interference that may cause undeslred
operatlnn of the devlce.‘
Changes or modifications not expressly approved by the party
responsible for compliance to the FCC Rules could veld the user‘s
authority to operate mls equlpmsnt.
Wamlng: Changes or modifications to thls unit not expressly approved
by the party responsible toroompllance could void the user‘s authority
to operate the equipmem.
TROUBLE SHOOTING
NO SOUND - Ensure the AC adapter is tulw Inserted Into the AC
outlet and into the power connection input on the
transmitterl
- Ensure the headphones' ONIOFF switch is In the ON
position.
- Headphone's battery may be the low Charge battery.
Charge the new bettertes lor 24 hours prior to the
first use.
- Ensure the TV. Hi-Fi or audio component is ON and
tuned to a channel with audio.
- Adjust the volume control on me headphone to turn
up the volume.
- The connected audio / video equipment is not playing,
start playing the equipment.
- The volume at headphone is turned down, adjust the
volume to an appropriate level.
DISTORTED - Ensure the stereo imficatnr light is ON. It not. press
the Auto Tuning button on the heedphenes until the
indicator light is on.
- Change the position at the FREQ. ADJUsT control
to change Operating lrequency of transmitter. You
must then press me Auto Tuning on the headphone
until [he stereo indicator lighs.
- Headphone's ballery may be too low. Charge the
battery or replaoe with the new battery.
. Ensure the level central wheel is tuned properly.
- The headphone is too tar tram transmitter. move '
closer.
- The input level at the audio signal is too low. Turn up
the volume of the audio source equipment.
93-01 0866

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Modify Date                     : 1999:09:14 10:34:35
Creator                         : Photoshop PDF Plug-in 1.0
Producer                        : Photoshop PDF Plug-in 1.0
Create Date                     : 1999:08:27 18:07:55
Page Count                      : 10

EXIF Metadata provided by EXIF.tools