Uniden America SX377 462MHz FRS/GMRS Walkie-talkie User Manual SX377 02022017 indd

Uniden America Corporation 462MHz FRS/GMRS Walkie-talkie SX377 02022017 indd

User Manual

SX377SX3791234581011Radio color/pattern varies according to model number.67915141312*Range may vary depending on environmental and/or topographical conditions.• 22 Channels (15 GMRS / 7 FRS Channels)• 7 Weather Channels• 142 Privacy Codes (CTCSS Tone and DCS Code)• Up to 37 Mile Range*• Internal VOX Circuitry• TRU Waterproof™ (IPX7/JIS7) — Submersible and Floats• Direct Call with Name Display• 143 Group Codes• Silent Mode• 10 Selectable Call/Ring Tone Alerts• Backlit LCD Display• Roger Beep• Call Alert; Vibrate• 2 Earbuds with VOX Mic or 2 Headset Boom Mics (depending on model number)1 Antenna 9 Charging Contacts2Push to Talk 10 MicroUSB port and earbud jack3 Boost (Change transmission power from 1.0W to 2.5W.)11 Channel (UP/DOWN)4 Channel UP/DOWN 12 Enter/Lock5 Menu/Power 13 Tone/Group6 D Call 14 WX Alert7 Light/MON 15 Microphone8 SpeakerCongratulations on your purchase of a Uniden SX377/379 series radio. This lightweight, palm-sized radio is a state-of-the-art device, equipped with many valuable features. Use it at sporting events, to stay in contact with family and friends, hiking, skiing, outdoors, or in a neighborhood watch for vital communication.Your radio complies with IPX7/JIS7 water-resistant standards, which means the radio can be submerged in 3.3 feet (1.0 meters) of water for 30 minutes without damage.• The radio will only meet this rating if fully assembled and all rubber seals and the jack cover are well maintained and correctly fitted. This means that the Headset plug is not inserted, and the Headset jack cover and the battery pack are attached and securely fastened.• After your radio is submerged in water, you might notice that the sound is distorted. This is because water remains in and around the speaker and microphone. Just shake the radio to clear excess water, and the sound should return to normal.Note: If your radio is exposed to salt water, clean your radio thoroughly with fresh water and dry it before turning it on.PACKAGE CONTENTSEach radio uses 3 AA rechargeable Ni-MH batteries, included. If your model number contains a "C," your package contains a microUSB Y charging cable. If your model number contains "CK," it contains a charging kit (including a charging cradle).If your models number contains "HS," it contains headsets.Refer to the packaging for other specific contents.GMRS LICENSEThe radio operates on the General Mobile Radio Service (GMRS) frequencies when using Channels 1-7 and channels 15-22. You must have a GMRS license issued by the Federal Communications Commission to legally use these channels.For licensing information and application forms, visit the FCC online at: www.fcc.gov/wtb/uls or call the FCC hotline at 1-800-418-3676. If you have any questions, you can contact the FCC direct at 1-888-225-5322.INSTALL THE BATTERYThese radios each use 3 rechargeable AA NiMH batteries for power (included).1. Remove the belt clip if necessary.2. Turn the screws holding the battery compartment counterclockwise with a screwdriver and lift up the battery cover,3. Insert the NiMH batteries in the battery compartment according to the directions inside the case. Installing the batteries incorrectly will prevent the unit from operating.4. Before placing the battery cover back on the radio, check the rubber seal around the battery compartment. Make sure that the seal is in good condition and that there is no foreign matter under it. 5. Replace the battery compartment door. Tighten the screws securely.6. Replace the belt clip if necessary.Note: If the rubber seal appears worn, nicked, or dried out, replacement seals are available from www.uniden.com.CHARGING THE RADIOFollow these instructions to charge or recharge your radios.Make sure to turn the radio OFF before placing it in the charging cradle.1. Insert the adapter's microUSB plug to DC IN 5V USB jack of the charging cradle and plug the other end into an AC outlet.2. Set the charging cradle on a stable desk or tabletop and place the radios in the charging cradle with the keypad facing forward.3. Make sure that the LED illuminates. Charge the batteries for 16 hours and remove the radio from the charging cradle after charging.Note: • Use only the supplied batteries and AC adapter or approved accessories from Uniden.• Charge time may vary depending on the battery life remaining.• The batteries must be installed for the unit to operate, even if the unit is also connected to external power.• If battery power is low, you cannot operate the radio even using external power. Allow the batteries to charge before using. If you try to transmit while power is low, the radio will automatically turn off.• Charge time may vary depending on the battery life remaining.• For faster charging, turn off the radio before charging.Warning! • The charging cradle is not waterproof. If the charging cradle falls in the water, unplug it than 1 second.Note: Channels 1-7 and 15-22 have a typical range of up to 37 miles by pressing BOOST. HI displays when you select a GMRS channel, and LO displays when you select an FRS channel.SETTING UP GROUP MODEGroup mode lets several people talk on the same channel in a separate group. In order to use Group mode, you need to initialize specific settings in your radio:• Set the radio to Group mode.• Set a Group Code.• Set a Unit Number.• Set a "Nickname."Setting the Radio to Group ModeTo set the radio to Group mode, which enables Direct Call, Auto Channel Change, and All Call, press and hold TONE/GROUP for 2 seconds. The radio displays GRP and group code.Note: In Group mode, you cannot receive transmissions from other radios unless they are also set to the same channel and group code.Setting the Group CodeSet the group code for your radio group from 0-142. Everyone in your group must select the same group code in order to communicate with each other.1. PressTONE/GROUP in Group mode. Press CH or to select the group number.2. Press ENTER/LOCK or TONE/GROUP to return to normal operation.Setting the Unit NumberEach radio in your group needs to be set to a unique unit number, from 1-16.1. Press MENU/ . Advance through the menu until UNIT appears, and then press ENTER/LOCK. The current unit number flashes.2. Press CH or to select the desired unit number.3. Press ENTER/LOCK to continue to the next section.Setting Your NicknameYour nickname appears on other units’ displays when you make an All Call or Direct Call. This is also the name that appears on other radio displays when someone wants to make a Direct Call to you. Without a nickname, the unit number shows.1. Press MENU/ and advance through the menu until UNIT appears; then press ENTER/LOCK. The current unit number flashes, then press ENTER/LOCK The radio displays - - - - (or your current nickname) with the first place in the nickname flashing.2. Press CH or to select the letter, then ENTER/LOCK to advance to the next letter until you have entered your nickname.3. Press MENU/ to confirm the setting and exit the menu.Using Group ModeGroup mode lets you make direct calls to other people in your group without alerting the entire group and also lets you quickly change everyone in your group to another channel from a single radio. Before using Group mode, follow the instructions in "Setting Up Group mode" on every radio in your group. Then, to record the unit ID and everyone’s nickname in every radio, send a call to "All" from each radio one time (see "Sending a Direct Call").Sending a Direct CallDirect Call lets you call everyone in your group at once, or call a single person in your group without anyone else in the group knowing. It is like a "speed dial" directly to the person(s) you want to talk to.To call everyone in your group, press D CALL in Group mode. The radio flashes ALL. Then, press D CALL or ENTER/LOCK Everyone in your group receives a call "chirp" for about 3 seconds. When the chirp ends, begin your conversation.Note: When you make a direct call to "all," your radio also sends out your nickname or ID so that it will show up in the call list for everyone in your group.To call one person in your group without having other people know, press D CALL in Group mode. Then, use CH or to select the person you want to call and press D CALL or ENTER/LOCK. Your radio sounds tones for 3 seconds as it sends the call. When the selected person answers, you can begin your conversation.You can silence the call tones any time by pressing PTT or BOOST.Your conversation remains private between you and the person you called until 15 seconds after your last conversation. Then, your radio automatically exits Private mode.Automatically Changing ChannelsAuto Channel Change lets you easily coordinate a channel change for everyone in your group. You might want to do this when you find you are getting a lot of interference on your current channel. You also use this feature to change from a low-power channel (8-14) to one of the To turn on channel scan:Press MENU/ . The radio displays SCAN. Press ENTER/LOCK. The channel number changes as the radio rapidly cycles through the channels.Use the radio in Standard (not Group) mode when you need to be able to communicate with radios that do not have the group feature.Talking on Your RadioTo talk to others using the radio:1. Press and hold PTT or BOOST and speak in a clear, normal voice about 2-3 inches away from the microphone. While you transmit, TXHI or TXLO appears on the display according to the type of channel. To avoid cutting off the first part of your transmission, pause slightly after pressing PTT or BOOST before you start talking.2. When you finish speaking, release PTT or BOOST. You can now receive incoming calls. While receiving, RX appears on the display.Note: • When you press BOOST, BOOST appear on the display. The radio transmits at maximum power when a GMRS channel is selected. • If BOOST, PTT or VOX is continuously used, 1 minute after you start using the feature the transmission stops and you hear a timeout error tone.Monitor Mode FeatureYour radio lets you listen for weak signals on the current channel at the press of a key.To turn on the Monitor mode:• Press and hold LIGHT/MON for 2 seconds until two beeps sound for continuous listening. The receiver circuit stays open, so you hear both the noise and weak signals.To turn off Monitor mode:Press LIGHT/MON to return to the previous mode. MON and RX disappear.Navigating through the Normal MenuYour radio has a Menu function to access advanced features. In order to use Auto Channel Change, you need to set your radio to Group mode.Start Scanning Scan Mode Silent Mode ON-OFF Auto Channel Change Channel Change VOX Level OFF, 1-5 1-10 Call Tone Unit Setting Setting Unit Number Roger Beep ON-OFF Beep Tone ON-OFF Setting Nickname 1. To enter the menu, press MENU/ .2. Press MENU/ again to advance through the menu. After the last menu item, the radio exits to the previous mode.3. Other ways to exit the Menu function are:a. Press PTT, BOOST, LIGHT/MON, D CALL, WX/ALERT or TONE/GROUP.b. Wait 10 seconds until the radio automatically returns to the previous mode.Setting Silent ModeWhen you turn on Silent mode, all incoming calls are muted, the display backlight flashes, and the channel indicator displays SLNT and CALL to alert you to an incoming call. If you do not respond to the call within 15 seconds, the backlight turns off. The radio will also vibrate to remind you that you missed a call. Silent mode is disabled for 15 seconds when you transmit, receive, or press any other button.To set Silent mode:1. Enter the menu. Advance through the menu until the SLNT displays, then press ENTER/LOCK. The current setting flashes.2. Press CH to display on, then press ENTER/LOCK.Note: To prevent unwanted silent alerts, be sure to use a Privacy Code or Group Code whenever you use the Silent mode feature.You can hear the received voice when you turn on channel scan and an active channel is detected, even during Silent mode. Missed Call AlertsIf you receive an incoming call while Silent mode is on and do not respond, the radio will turn on the Missed Call icon. If you are using Group mode, the radio will also indicate who made the call.The radio also remind you of a missed call by vibrating every minute after the call for 3 minutes.• BOOST for Maximum Range*• Headset Jack• Auto Channel Change• Battery Level Meter• Rechargeable NiMH Batteries• Dual Charging Cradle with AC Adapter• Channel Monitor• Channel Scan Group Scan• Keypad Lock• Emergency Weather Alert• Emergency Light• Last Channel Memoryhigh-powered channels (1-7, 15-22) for more range (or to a low-power channel if you need longer battery life).To start an auto channel change, on any radio in the group, press MENU/ . Advance through the menu until CHCX appears, then press ENTER/LOCK. The current channel flashes. Use CH or to select the target channel. You can check whether the selected channel is clear. Then press D CALL or ENTER/LOCK.Your radio chirps for about 10 seconds while it sends out the channel change signal. As each radio receives the channel change signal, it chirps once, then changes to the new channel.To ensure all radios make it to the new channel, we recommend you:• Make sure you are in an open environment, where the radio will get the best range.• Optimize range during the channel change signal by raising the radio over your head to give the best possible height.• Do a "roll call" on the new channel after the move to be sure no one was left behind. If you missed someone, return to the previous channel and issue the signal again.USING THE RADIO IN STANDARD MODEUse the radio in Standard (not Group) mode when you need to be able to communicate with radios that do not have the group feature.Choosing a Privacy CodeYou can select a Privacy Code from 1-142 for each channel. oF (off) indicates no Privacy Code selected and your radio can receive a signal regardless of the code settings of the transmitting radio.1. Press TONE/GROUP. The Privacy Code indicator flashes.2. Press CH or to increase or decrease the code. You can also select oF.3. Press ENTER/LOCK or TONE/GROUP to return to normal operation.Note: Only tones 1-38 are standard across radio brands. Other settings might differ from brand to brand. See the specifications for the specific tones used for each setting.Channel Scan FeatureYour radio has a channel scan feature that lets you easily scan all 22 channels. When an active channel is detected, the radio pauses on that channel until the channel is clear. Then after a 2-second delay, the radio resumes scanning. Pressing PTT or BOOST while the scan is paused on a channel lets you transmit on that channel. Voice Operated TransmissionYour radio is equipped with a user selectable Voice Operated Transmitter (VOX) that can be used for automatic voice transmissions. The VOX feature is designed to be used with a headset with a microphone. Initiate transmission by speaking into the remote microphone instead of pushing PTT and BOOST. To select the VOX level:1. Press MENU/ . Advance through the Menu until VOX appears on the display, then press ENTER/LOCK. The current level (off, 1-5) flashes. Level oF (off) disables VOX, while levels 1-5 set the sensitivity of the VOX circuit.2. Press either CH or to reach the desired VOX sensitivity level, then press ENTER/LOCK. Use level 1 for increased sensitivity to voice in normally quiet environments, and use a higher level to reduce undesired activation in very noisy environments.Transmitting a Call ToneYour radio is equipped with 10 selectable call tones that are transmitted when you press D CALL in Standard mode.The selected tone also will be heard when someone places a direct call to you.To select a call tone:1. Press MENU/ . Advance through the menu until CALL appears, then press ENTER/LOCK. The current call tone number (1-10) flashes.Press CH or to increase or decrease the number to the desired call tone. Each tone will be heard through the speaker. Press ENTER/LOCK to select a call tone.To transmit the selected call tone, press D CALL. The selected tone is transmitted for a fixed length of time. Press PTT or BOOST to cancel.Roger BeepRoger Beep is a beep that is sent to notify the end of transmission (both PTT and VOX transmission). You can hear Roger Beep through the speaker when both Roger Beep and Beep Tone are on. When Roger Beep is on and Beep Tone is off, you do not hear Roger Beep, but it is transmitted to your party.To adjust Roger Beep, press MENU/ . Advance through the menu until RGR appears, then press ENTER/LOCK. The current setting flashes.To turn off Roger Beep:Press CH to display oF, then press ENTER/LOCK.To turn on Roger Beep:Press CH to display on, then press ENTER/LOCK.before attempting to remove it from the water. Allow the cradle to dry completely before reconnecting the power.• Wipe off dirt or shake water from your radio before placing in the charging cradle if your radio is soiled or wet.USING A HEADSETDepending on the model number, your radios may come with an earbud headset with mic on the cord or with a boom mic headset. To use a headset, lift the rubber cover from over the headset jack, then plug in the headset.Important: Your radio is not waterproof when using a headset jack. When you remove the headset, be sure to fully press the jack cover into place to restore its waterproof capability.USING RADIO BATTERY LEVEL AND LOW BATTERY ALERTThis radio has a battery level meter that indicates the battery power level. When the battery level is low, the battery level meter icon flashes and then BATT appears after 30 seconds. Recharge the NiMH batteries immediately.Warning! To avoid the risk of personal injury or property damage from fire or electrical shock, only use the Uniden accessories specifically designated for this product.USING THE RADIOIn order to get the most out of your new radio, read this reference guide completely before attempting to operate it.Turning the Radio On and Adjusting the Volume1. Press and hold MENU/ to turn the radio on.2. Press VO or to increase or decrease the volume level then press ENTER/LOCK.3. Press and hold MENU/ to turn the radio off.Choosing a ChannelYour radio has 22 channels and 142 Privacy codes you can use to talk to others. In order to speak to someone, both your radios must be set to the same channel and Privacy code.To choose a channel:Press CH or , then press CH or to increase or decrease the channel number displayed.To scroll through the channels, press CH or , then press and hold CH or for more
Adjusting the Sound (Beep Tone)Your radio sounds a beep each time you press a key (except for PTT and BOOST).To adjust the sound, press MENU/ . Advance through the menu until TONE appears, then press ENTER/LOCK. The current setting flashes.To turn off the beep:Press CH to display oF, then press ENTER/LOCK.To turn on the beep:Press CH to display on, then press ENTER/LOCK.Key LockPress and hold the ENTER/LOCK until LOCK appears. To turn Keylock off, press and hold ENTER/LOCK again.Note:• If Keylock is on, the radio can still receive transmissions. Use D CALL in Standard mode, VO or , PTT, BOOST, LIGHT/MON, and MENU/ to turn the radio on or off.• The radio retains the keylock status even when you cycle power. Using the FlashlightYou can use this radio in an emergency. If you press LIGHT/MON, the radio turns on the high-intensity LED flashlight on your radio. Depending on how you set it up, the LED functions as a flashlight, flashes “S O S” in international Morse Code, is always on, or is off.Note: Your radio operates normally when the SOS strobe is activated.1. Press LIGHT/MON while this light is turned off, the Strobe Light emits the SOS signal. (Strobe SOS mode)2. And then, press LIGHT/MON once more, it will turn on continuously. (Always On mode)3. And then, press LIGHT/MON while Always On mode, the light will be turned off.Automatic Power Save FeatureYour radio has a unique circuit designed to dramatically extend the life of the battery. If you do not transmit and do not receive an incoming call within 3 seconds, your radio switches to the Power Save mode. The radio is still able to receive transmissions in this mode.LCD BacklightThe LCD Backlight automatically turns on when any key (except for PTT and BOOST) is pressed. The LCD remains lit for 10 seconds before turning off.USING THE WEATHER RADIOYour radio can receive weather broadcasts from the NOAA National Weather Service. When in Weather Radio Alert mode, the system functions as it does in Standard mode or Group mode but also monitors the selected weather channel for alerts when not communicating. While using the Weather Radio, you are not able to receive GMRS communications.1. To turn on the Weather Radio Broadcast mode, press WX/ALERT. WX appears.2. Press CH or to increase or decrease the number to the desired Weather Channel.3. To exit the Weather Radio Broadcast mode, press WX/ALERT. WX disappears.When in the Weather Radio Broadcast mode, you can only set the Beep Tone from the Menu mode.Choosing an Emergency/Weather ChannelThere are 7 NOAA channel frequencies available and these frequencies are common between the US and Canada. You need to know what frequency is being transmitted in your location.1. Press and hold WX/ALERT. appears.2. When the unit receives a warning signal, it beeps for 5 seconds. and channel indicator flash.3. To turn off Weather Alert, press and hold WX/ALERT. disappears.• When Weather Alert is activated, the highest priority is given to this function. It checks the weather alert signals every 7 seconds. When the unit finds a warning signal, it switches to the Warning Receive mode automatically.• Weather Alert is activated even if Beep Tone is off.NOAA Weather Radio Frequency List:Chan. Freq. (MHz)Chan. Freq. (MHz)1 162.550 5 162.4502 162.400 6 162.5003 162.475 7 162.5254 162.425SPECIFICATIONSItem SpecicationChannels 15 GMRS/7 FRS/7 WeatherPrivacy Codes 38 Sub-Codes83 DCS CodesOperating Frequency (MHz) GMRS/FRS: 462.5500 - 467.7125Item Specication WX: 162.4000 - 162.5500Power Source Per radio: 3 AA NiMH Batteries (700 mAh)Range (Chan.) 37 Miles 1-7 Up to 18 (up to 50 with BOOST) 8-14 Up to 5 15-22 Up to 18 (up to 50 with BOOST)Battery Life (Hours)8.5 Hours (typical) -- NiMH Batteries (5/5/90 duty cycle)FREQUENCIESFrequency ChartCH. Freq. Cross-Ref. CH. Freq. Cross-Ref.1 462.5625 FRS & GMRS 1 12 467.6625 FRS 122 462.5875 FRS & GMRS 2 13 467.6875 FRS 133 462.6125 FRS & GMRS 3 14 467.7125 FRS 144 462.6375 FRS & GMRS 4 15 462.5500 GMRS 115 462.6625 FRS & GMRS 5 16 462.5750 GMRS 86 462.6875 FRS & GMRS 6 17 462.6000 GMRS 127 462.7125 FRS & GMRS 7 18 462.6250 GMRS 98 467.5625 FRS 8 19 462.6500 GMRS 139 467.5875 FRS 9 20 462.6750 GMRS 1010 467.6125 FRS 10 21 462.7000 GMRS 1411 467.6375 FRS 11 22 462.7250 GMRS15CTCSS & DCS CODESCTCSS Chart (Hz)Code Freq. Code Freq. Code Freq.oF OFF 13 103.5 26 162.21 67.0 14 107.2 27 167.92 71.9 15 110.9 28 173.83 74.4 16 114.8 29 179.94 77.0 17 118.8 30 186.25 79.7 18 123.0 31 192.86 82.5 19 127.3 32 203.57 85.48 20 131.8 33 210.78 88.5 21 136.5 34 218.19 91.5 22 141.3 35 225.710 94.8 23 146.2 36 233.611 97.4 24 151.4 37 241.812 100.0 25 156.7 38 250.3DSC Code ListTone No.Octal CodeTone No.Octal CodeTone No.Octal Code39 023 67 174 95 44540 025 68 205 96 46441 026 69 223 97 46542 031 70 226 98 46643 032 71 243 99 50344 043 72 244 100 50645 047 73 245 101 51646 051 74 251 102 53247 054 75 261 103 54648 065 76 263 104 56549 071 77 265 105 60650 072 78 271 106 61251 073 79 306 107 62452 074 80 311 108 62753 114 81 315 109 63154 115 82 331 110 63255 116 83 343 111 65456 125 84 346 112 66257 131 85 351 113 66458 132 86 364 114 70359 134 87 365 115 71260 143 88 371 116 72361 152 89 411 117 73162 155 90 412 118 73263 156 91 413 119 73464 162 92 423 120 74365 165 93 431 121 75466 172 94 432MAINTENANCETo be safe and sure:• Never open your radio’s case.• Never change or replace anything in your radio except the batteries.Care and SafetyTo clean the radio, use a soft cloth dampened with water. Do not use cleaners or solvents because they can harm the body of the unit and leak inside, causing permanent damage. Use a dry, lint-free cloth to clean the battery contacts. Do not submerge the unit in water. If the unit gets wet, turn it off and remove the batteries immediately.Dry the battery compartment with a soft cloth to minimize potential water damage. Leave the battery compartment cover off overnight to ensure complete drying. Do not use the radio until the unit is completely dry.Your radio might cause TV or radio interference even when it is operating properly. To determine whether your radio is causing the interference, turn it off. If the interference goes away, your radio is causing it. Try to eliminate the interference by moving your radio away from the receiver. If you cannot eliminate the interference, the FCC requires that you stop using the radio.Hazardous EnvironmentsDo not operate the radio in hazardous environments. Explosion or fire may result. Do not operate the radio near unshielded electrical blasting caps.Under certain conditions, radios can interfere with blasting operations and may cause an explosion. Turn your radio OFF to prevent accidental transmission when in a blasting area or in areas posted: "Turn off two-way radio." Construction crews often use remote control RF devices to set off explosives.WARNING! Read this information before using the radio. In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters.Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of the radio complies with the FCC guidelines and these international standards.Never allow children to operate the radio without adult supervision and the knowledge of the following guidelines.WARNING! It is up to the user to properly operate this radio transmitter to insure safe operation. Please adhere to the following:Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for a replacement antenna. REGULATORY INFORMATIONHand-Held Operation (Held-to-Face)This device was evaluated for typical hand-held (held-to-face) operations with a 1 inch spacing from the front of the radio. For hand-held operation, the radio should be held 1 inch from the user's face in order to comply with FCC RF exposure requirements.Body-Worn OperationThis device was evaluated for body-worn operations with the supplied belt-clip accessory. (All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines.) Third party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines. For body worn operation, this device has been tested and meets the Industry Canada RF exposure guidelines when used with Uniden accessories supplied or designated for this product. Use of other accessories may not ensure compliance with Industry Canada RF exposure guidelines.Fonctionnement de l’appareil, lorsque porté sur le corps. Cet appareil a été testé et s’est avéré conforme aux normes d’Industrie Canada et approuvé pour le port sur le corps à l’aide des accessoires Uniden inclus et conçus pour cet appareil. L’utilisation d'accessoires ne respectant pas les exigences d'exposition RF d’Industrie Canada doit être évitée. FCC PART15/IC COMPLIANCEFCC PART 15 COMPLIANCE This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.Avis de conformité à la FCC : Ce dispositif a été testé et s’avère conforme à l’article 15 des règlements de la Commission fédérale des communications (FCC). Ce dispositif est soumis aux conditions suivantes: 1) Ce dispositif ne doit pas causer d’interférences nuisibles et; 2) Il doit pouvoir supporter les parasites qu’il reçoit, incluant les parasites pouvant nuire à son fonctionnement.Tout changement ou modification non approuvé expressément par la partie responsable pourrait annuler le droit à l’utilisateur de faire fonctionner cet équipement.IC ComplianceThis device complies with Industry Canada license-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OVERPAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty . is void outside the United States of America and Canada.PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owner’s manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). Disconnect the battery from the Product and separately secure the battery in its own separate packaging within the shipping carton. The Product should include all parts and accessories originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused you to return it.The Product should be shipped freight prepaid, by traceable means, to warrantor at:Uniden America Service C/O Saddle Creek 743 Henrietta Creek Road, Suite 100 Roanoke, TX 76262Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.Cet appareil est conforme aux normes RSS exemptes de licences d’Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférences nuisibles et (2), il doit pouvoir accepter les interférences, incluant celles pouvant nuire à son fonctionnement normal.Tout changement ou modification non approuvé expressément par la partie responsable pourrait annuler le droit à l’utilisateur de faire fonctionner cet équipement.ONE YEAR LIMITED WARRANTYImportant: Save your receipt! Evidence of original purchase is required for warranty service.WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden")ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below.WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale. The warranty is invalid if the Product is: (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, sub-assemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner’s manual for this product.STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY © 2017 Uniden America Corp. Issue 1, February 2017All rights reserved Printed in China

Navigation menu