Uniden America UC577B DECT PHONE-BASE UNIT User Manual CT14 OM 0912

Download:
Mirror Download [FCC.gov]
Document ID	1080381
Application ID	8DtfQJ3nQttUBLnRJGMhOA==
Document Description	Owners Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.15kB (101845 bits)
Date Submitted	2009-03-13 00:00:00
Date Available	2009-03-13 00:00:00
Creation Date	2008-09-12 18:21:18
Producing Software	Acrobat PDFWriter 5.0 Windows NT
Document Lastmod	0000-00-00 00:00:00
Document Title	CT14_OM_0912.doc
Document Creator	CT14_OM_0912.doc - Microsoft Word
Document Author:	eng

CORDLESS HEADSET TELEPHONE
CT14
USERS MANUAL
Important Safety Instructions
When using your telephone equipment, basic safety
precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the
following:
1) Do not use this product near water, for example, near a
bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
2) Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote risk of
electric shock from lightning.
3) Do not use the telephone to report a gas leak in the
vicinity of the leak.
4) Use only the power cord and batteries indicated in this
manual. Do not dispose of batteries in a fire. They may
explode. Check with local authorities for possible battery
disposal instructions.
5) Do not disassemble any component of this product.
SAVE THESE INSTRUCTIONS
CAUTION:
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions. Do
not open or mutilate the battery, and disconnect the battery
before shipping this product.
FCC Registration Information
Changes or modifications to this product not expressly
approved by our company, or operation of this product in any
way other than as detailed by the owner's manual, could void
your authority to operate this product.
This equipment complies with Part 68 of the FCC rules and
the requirements adopted by the ACTA. On the bottom of
this equipment is a label that contains, among other
information, a product identifier in the format US:
AAAEQ##TXXXX. If requested, this number must be
provided to the telephone company. An applicable Universal
Service Order Codes (USOC) certification for the jacks used
in this equipment is provided (i.e., RJ11C) in the packaging
with each piece of approved terminal equipment. A plug and
jack used to connect this equipment to the premises wiring
and telephone network must
comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA.
A compliant telephone cord and modular plug is provided
with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See
installation instructions for details. The REN is used to
determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may
result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not
exceed five (5.0).
To be certain of the number of devices that may be
connected to a line, as determined by the total RENs,
contact the telephone provider. For products approved after
July 23, 2001, the REN for this product is part of the product
identifier that has the format US:AAAEQ##TXXXX. The
digits represented by ## are the REN without a decimal point
(e.g., 03 is a REN of 0.3). For earlier products, the REN is
separately shown on the label.
If this equipment causes harm to the telephone network, the
telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance
notice isn’t practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it is
necessary. The telephone company may make changes in
its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens the
telephone company will provide advance notice in order for
you to make necessary modifications to maintain
uninterrupted service.
Please follow instructions for repairing if any (e.g. battery
replacement section); otherwise do not alternate or repair
any parts of device except specified.
Connection to party line service is subject to state tariffs.
Contact the state public utility commission, public service
commission or corporation commission for information.
NOTICE: If your home has specially wired alarm equipment
connected to the telephone line, be sure that installing the
system does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult
your telephone company or a qualified installer.
Should you experience trouble with this equipment, please
contact our service center for repair or warranty information.
If the equipment is causing harm to the telephone network,
the telephone company may request that you disconnect the
equipment until the problem is resolved.
NOTICE: According to telephone company reports, AC
electrical surges, typically resulting from lightning strikes, are
very destructive to telephone equipment connected to AC
power sources. To minimize damage from these types of
surges, a surge arrestor is recommended.
To insure the safety of users, the FCC has established
criteria for the amount of radio frequency energy various
products may produce depending on their intended usage.
This product has been tested and found to comply with the
FCC’s exposure criteria. For body worn operation, the FCC
RF exposure guidelines were also met when used with
accessory (belt clip) supplied or this product. Use of other
accessories may not ensure compliance with FCC RF
exposure guidelines and should be avoided.
The antenna(s) used for the base-unit must be installed to
provide a separation distance of at least 20 cm from all
persons and must not be collocated or operated in
conjunction with any other antenna or transmitter.
Radio interference may occasionally cause buzzing and
humming in your cordless handset, or clicking noises in the
base. This interference is caused by external sources such
as TV, refrigerator, vacuum cleaner, fluorescent lighting, or
electrical storm. Your unit is NOT DEFECTIVE. If these
noises continue and are too distracting, please check around
your home to see what appliances may be causing the
problem. In addition, we recommend that the base not be
plugged into a circuit that also powers a major appliance
because of the potential for interference. Be certain that the
antenna on the unit is fully extended when needed. In the
unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be
receiving radio signals from another cordless telephone or
other source of interference. If you cannot eliminate this type
of interference, you need to change to a different channel.
Finally, it should be noted that some cordless telephones
operate at frequencies that may cause interference to
nearby TVs and VCRs. To minimize or prevent such
interference, the base of the cordless telephone should not
be placed near or on top of a TV or VCR. If interference is
experienced, moving the cordless telephone farther away
from the TV or VCR will often reduce or eliminate the
interference.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This
device must accept any interference received, including
interference that may cause undesired operation. Privacy of
communications may not be ensured when using this phone.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and
receiver.
--Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician
for help.
I.C. Notice
Terminal equipment
NOTICE: This equipment meets the applicable Industry
Canada Terminal Equipment Technical Specifications. This
is confirmed by the registration number. The abbreviation, IC,
before the registration number signifies that registration was
performed based on a Declaration of Conformity indicating
that Industry Canada technical specifications were met. It
does not imply that Industry Canada approved the
equipment.
NOTICE: The Ringer Equivalence Number (REN) for this
terminal equipment is marked on the equipment itself. The
REN assigned to each terminal equipment provides an
indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject
only to the requirement that the sum of the Ringer
Equivalence Numbers of all the devices does not exceed
five.
Radio equipment
The term “IC:” before the radio certification number only
signifies that Industry Canada technical specifications were
met.
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may
cause undesired operation of the device. “Privacy of
communications may not be ensured when using this
telephone.”
Parts of the Phone
Base
1)
2)
3)
4)
5)
Base Antenna / Headset Holder
CHARGE Indicator (LED)
PAGE key
DC Power Input
Telephone Line Jack
Handset
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
21)
22)
23)
Headset Jack
MESSAGE WAITING Indicator (LED) *
* Must be activated through your local phone company.
Display (LCD)
TALK/FLASH Key
PHONEBOOK/LEFT (Phonebook/Left Cursor) Key
DOWN Key
UP Key
* Key
Charging Contacts
END Key
CID/RIGHT (Caller ID */Right Cursor) Key
* Must be activated through your local phone company.
MENU/SEL (Menu/Select) Key
INT’COM/CLEAR (Intercom/Clear) Key
VOICEMAIL/MUTE Key
PAUSE/REDIAL Key
# Key
Battery Compartment Cover
AC Adapter (not shown)
24) Battery Pack (not shown)
25) Telephone Cord (not shown)
26) Belt Clip
Headset
Installing the Phone
Location Considerations
1) Locate the system in a central part of your working area
near a phone and a power outlet.
2) Do not locate it near a computer, microwave, or other
electronic devices such as TV’s and other cordless
devices.
3) Do not locate it near heat sources, noise sources,
excessive moist environments, dusty environments, and
mechanical vibration environments.
1 Install Battery Pack
1.1) Squeeze the latch on the Battery Compartment Cover
(22) and lift the cover.
1.2) Connect the Battery Pack (24) connector using the
correct polarity. Do not force. Plastic connectors will fit
in only one way.
1.3) Insert battery pack into the battery compartment. Do
not let wires hang out, tuck them in.
1.4) Insert tabs of cover into slots and push down to
securely close the cover.
2 Set Up the Base
2.1) Connect the AC adapter power cord to the base and an
active AC outlet.
2.2) Route the power cord as shown in the detail drawing
allowing clearance for the telephone plug to be
inserted.
2.3) Insert the handset into the charging cradle on the base.
Charge for 15-20 hours. The CHARGE indicator (2)
light will go on.
2.4) Raise the Base Antenna (1) to a vertical position.
2.5) Once the handset is fully charged, plug one end of the
telephone cord into the base and plug the other end
into an active telephone outlet.
3 Install the Headset
3.1) Place the headset on your head so the speaker covers
your ear.
3.2) Adjust the tip of the microphone boom toward the
corner of your mouth.
3.3) Plug the headset cord into the 2.5mm jack on the top of
the handset.
3.4) Route the cord through the handset’s cord retainer slot.
4 Installing the Belt Clip (for body worn operation)
To attach the belt clip
Insert the tabs on the sides of the belt clip into the holes on
either side of the handset. Press the belt clip down until it
clicks into place. (Tug on the clip to make sure it’s secure.)
To remove the belt clip
Pull one side of the belt clip to release the tab from the hole.
5 Make Basic Setting Changes, if necessary
5.1 Selecting a Language
Your handset supports three languages: English, French and
Spanish. The default language is English.
1) With the phone in standby, press MENU/SEL (17).
2) Use UP (12) or DOWN (11) to select the Handset Setup
menu, and then press MENU/SEL.
3) Use UP or DOWN to select the Handset Language
submenu, and then press MENU/SEL.
4) Move the cursor to choose English, Français (French) or
Español (Spanish).
5) Press MENU/SEL. You will hear a confirmation tone.
5.2 Changing the dial mode
Your phone can communicate with the telephone network in
two different ways: tone dialing or pulse dialing. These days,
most base networks use a method called tone dialing, so
your phone comes programmed for tone dialing. If your
phone company uses pulse dialing, you will need to change
your phone’s dial mode. If you don’t get a dial tone or can’t
connect to the telephone network, please follow the steps
below to modify your phone’s settings:
1) With the phone in standby, press MENU/SEL.
2) Use UP or DOWN to select the Global Setup menu, and
then press MENU/SEL.
3) Use UP or DOWN to select the Dial Mode submenu, and
then press MENU/SEL.
4) Press DOWN to select Pulse.
5) Press MENU/SEL. You will hear a confirmation tone.
If you ever need to change the dial mode back to tone dialing,
follow the same procedure, but select Tone in step 3.
6 Make and Receive Test Calls
With your headset mounted from Step 3 and any required
setting changes made from Step 4, prepare to make your
first call.
6.1 To make your first call
1) Pick up the handset from its base.
2) With the phone in standby, dial the number as you would
on an ordinary phone.
3) Press TALK/FLASH (9). After about two seconds the
10
number will be dialed.
4) Talk once you connect.
5) Adjust the listen volume for your hearing comfort using
UP or DOWN. You can choose from six volume levels.
6) Press END (15) to disconnect and hang up the call.
6.2 To redial
You can quickly redial the last five numbers dialed on the
handset.
1) With the phone in standby, press the PAUSE/REDIAL
(20) to open the redial list.
2) Use UP and DOWN or PAUSE/REDIAL to scroll through
the redial list.
3) When you find the number you want to dial, press
TALK/FLASH.
Tips:
You can also press TALK/FLASH before you open
the redial list. Find the phone number you want to
dial, and then press MENU/SEL.
6.3 To answer a call
1) Press TALK/FLASH and begin talking.
2) Press END to disconnect and hang up the call.
6.4 To mute a call
1) During a call, press VOICEMAIL/MUTE. Mute On and
the mute icon appear in the display; the mute icon
remains while muting is on.
2) To cancel muting, press VOICEMAIL/MUTE again. Mute
Off appears.
11
Terminology Used in this Manual
Base
Handset
CID
CID/CW
Standby
Talk
The main part of the phone that connects to
your phone line and lets you make and receive
calls.
A cordless handset that you use to dial the
phone and talk to callers with a headset.
Caller ID is available from your telephone
provider and is offered to users on a
subscription basis. With this service, you will
be able to see the incoming caller information
such as name and phone number.
Caller ID with Call Waiting is available by
subscription from your telephone provider.
With this service, you will be able to view
incoming caller information while on a call with
another user.
The handset and the base are not in use. (It
doesn’t matter whether the handset is in the
base: the TALK/FLASH or SPEAKER hasn’t
been pressed, and there is no dial tone.)
A dial tone has been enabled, so you can dial
and carry on a conversation with an outside
party.
Manual Conventions
This manual uses several different type styles to help you
distinguish between different parts of the phone:
• ALL CAPITALS BOLD ITALIC text indicates a key or
button on the phone
• Italic text indicates text on the display, such as menu
options, prompts, and confirmation messages
• BOLD text indicates a status light on the phone
12
Basics
Using the Handset Menu
•
•
•
•
•
•
•
To open the menu, press MENU/SEL.
The arrow cursor on the left side of the line shows which
menu item is currently highlighted. Use UP to move the
cursor up and DOWN to move the cursor down.
To select the highlighted option, press MENU/SEL.
To go back to the previous screen, press
PHONEBOOK/LEFT.
To exit the menu, press END.
If you don’t press any keys for thirty seconds, the phone
will time out and exit the menu. (When setting the day
and time, the time-out period is extended to two minutes.)
For Global Setup and Day & Time menu options, make
sure the line is not in use and the handset are within
range of the base.
Setting the Time
To change the time shown in the display, follow the steps
listed below.
1) Press MENU/SEL.
2) Move the cursor to Day & Time and press MENU/SEL.
3) Use UP and DOWN to select the day of the week, and
press MENU/SEL.
Note: With the phone in standby, the day of the week
does not appear on the handset display.
4) Use the number keypad (0 through 9) to enter the hour
and minutes.
5) Use UP and DOWN to select AM or PM, and press
MENU/SEL. You hear a confirmation tone.
Selecting a Ring Tone
You may choose from four melodies or three tones for your
phone’s primary ring tone. The handset can use a different
13
ring tone or melody. The available ring tones are as listed:
Tones
• Flicker
• Clatter
• Wake Up
Melodies
• Fur Elise (Elise)
• We Wish You A Merry Christmas (Merry-Xmas)
• Beethoven's Symphony #9 (Beethoven9)
• Home Sweet Home (Hm Swt Hm)
1) Press MENU/SEL.
2) Select the Handset Setup menu, and then the Ringer
Tones submenu.
3) Move the cursor to select a ring tone. As each ring tone is
highlighted, you will hear a sample (unless the handset
ringer volume is set to off).
4) When you hear the tone you want to use, press
MENU/SEL. You will hear a confirmation tone.
Activating Personal Ring
You can assign special ringer tones to anyone in your
phonebook. When your phone gets a call, it looks up the
Caller ID information in your phonebook. If you’ve assigned a
personal ringer to that number, the phone uses it so you
know who is calling. (See page 24 for how to assign a
personal ring tone.) To turn the personal ringing on or off,
follow these steps:
1) Press MENU/SEL.
2) Select the Handset Setup menu, and then the Personal
Ring submenu.
3) Move the cursor to select On or Off.
4) Press MENU/SEL. You will hear a confirmation tone.
14
Activating the Key Touch Tone
Key Touch Tone is the tone your keypad makes when keys
are pressed. You can turn this tone on or off.
1) Press MENU/SEL.
2) Select the Handset Setup menu, and then the Key Touch
Tone submenu.
3) Move the cursor to select On or Off.
4) Press MENU/SEL. You will hear a confirmation tone.
Changing the Handset Banner
Each handset will display a banner name once it is
registered to the base. The default banner is Handset #1.
You can change the name your phone displays by changing
the banner display. If you have more than one handset, the
banner name identifies your handset.
1) Press MENU/SEL.
2) Select the Handset Setup menu, and then the Banner
submenu.
3) Use the keypad to enter or edit the banner name. (See
Entering Text from Your Handset on 24 for detailed
instructions on entering text.)
4) Press MENU/SEL. You will hear a confirmation tone.
Note:
When you have multiple bases and even if the
handset ID is changed when you switch to a
different base, the handset will keep the banner
name.
Activating Auto Talk
Auto Talk allows you to answer the phone simply by picking
up the handset from the base. You do not have to press a
button to answer the call.
1) Press MENU/SEL.
2) Select the Handset Setup menu, and then the Auto Talk
submenu.
15
3) Move the cursor to select On or Off.
4) Press MENU/SEL. You will hear a confirmation tone.
Activating Any Key Answer
Any Key Answer allows you to answer the phone by pressing
any key on the twelve-key dial pad.
1) Press MENU/SEL.
2) Select the Handset Setup menu, and then the Any Key
Answer submenu.
3) Move the cursor to select On or Off.
4) Press MENU/SEL. You will hear a confirmation tone.
16
Using Your Phone
Making and Receiving Calls
Making a
call
Handset on the base
Handset off the base
1) Pick up the handset
from the base.
2) Press TALK/FLASH.
3) Listen for the dial
tone.
4) Dial the number.
OR
1) Pick up the handset
from the base.
2) Dial the number.
3) Press TALK/FLASH.
1) Press
TALK/FLASH.
2) Listen for the dial
tone.
3) Dial the number.
OR
1) Dial the number.
2) Press
TALK/FLASH.
1) Pick up the handset.
(If Auto Talk is on, the
phone will answer
when you pick up the
handset from the
Receiving
base.)
a call
2) Press TALK/FLASH.
(If Any Key Answer is
on, you can also
press any key on the
dial pad.)
Hanging
up
Press TALK/FLASH.
(If Any Key Answer is
on, you can also press
any key on the dial
pad.)
Press END or return the handset to the base.
17
Adjusting the Ringer and Earpiece Volume
Adjusting the Ringer Volume
You can choose from three ringer volume settings (off, low
and high) on the handset.
1) With the phone in standby, press UP or DOWN. The
display shows the current volume level and the handset
sounds the ringer at that level.
2) Use UP to make the ringer volume louder or use DOWN
to make it softer or turn it completely off.
3) When you hear the ringer volume level you want to use,
stop pressing keys. The handset will use the new ringer
volume starting with the next incoming call.
Note:
If you set the ringer volume to Off, the handset
won’t ring.
Muting the Ringer (One call only)
While the phone is ringing, press VOICEMAIL/MUTE or
END to mute the ringer for this call. The phone will ring again
on the next call. (The handset must be off the base to mute
the ringer.)
Adjusting the Earpiece Volume
You can choose from six volume levels for the handset
earpiece. To adjust the earpiece volume while on a call,
press UP (to make it louder) or DOWN (to make it softer).
The handset display shows the current volume level for the
earpiece.
Adjusting the Audio Tone
If you aren’t satisfied with the audio quality of your phone,
you can adjust the Audio Tone of the earpiece while on a call.
Your phone gives you three audio tone options: low, natural
and high; the default setting is Natural Tone. To adjust the
audio tone:
18
1) While on a call, press MENU/SEL.
2) Move the cursor to select Audio Tone, and then press
MENU/SEL.
3) Move the cursor to select desired option (High Tone,
Natural Tone, or Low Tone), and then press MENU/SEL.
Selected option appears in the display for two seconds,
and then the display returns to normal.
Muting the Microphone
Mute turns off the microphone so the caller can’t hear you.
This only works while you are on a call.
1) Press VOICEMAIL/MUTE. Mute On and the mute icon
appear in the display; the mute icon remains while
muting is on.
2) To cancel muting, press VOICEMAIL/MUTE again. Mute
Off appears.
Redialing a Number
You can quickly redial the last five numbers dialed on each
handset.
1) With the phone in standby, press the PAUSE/REDIAL to
open the redial list.
2) Use UP and DOWN or PAUSE/REDIAL to scroll through
the redial list.
3) When you find the number you want to dial, press
TALK/FLASH.
Notes: • If the number exceeds 32 digits, only the first 32
digits are retained in redial memory.
• If the redial memory is empty, Empty appears in
the display and you will hear a beep.
• You can also press TALK/FLASH before you
open the redial list. Find the phone number you
want to dial, and then press MENU/SEL.
19
Deleting a Redial Record
If you want to delete a phone number from the redial list,
follow the steps below:
1) With the phone in standby, press PAUSE/REDIAL.
2) Use UP and DOWN to scroll through the redial list.
3) When you find the redial number you want to delete,
press MENU/SEL and select Delete Entry.
4) When the phone asks you to confirm, select Yes. The
redial number is deleted.
Placing a Call on Hold
1) During a call, press INT’COM/CLEAR to place the caller
on hold. The display screen will read, Line On Hold.
2) To return to the party on hold, press TALK/FLASH. The
phone will return to the holding party.
Notes: • You can only place a caller on hold for five
minutes. Once five minutes has passed, that
party’s line will be disconnected and the phone
will return to standby.
• While a call is on hold, Call Waiting and CID on
Call Waiting do not work.
Finding a Lost Handset
To locate a misplaced handset, press PAGE on the base
when the phone is in standby. The handsets connected to
the paging base will beep for one minute, and PAGING
appears on the handset display. To cancel paging, press
PAGE again or any key on the found handset.
20
Using a Voice Mail Service
If you subscribe to a voice mail service, you can use your
phone to access your voice mailbox. When there are
messages waiting in your voice mailbox, the MESSAGE
WAITING Indicator on the handset flashes, and appears in
the handset display.
If you program your access number into your phone, you can
simply press VOICEMAIL/MUTE to access your voice mail.
Your voice mail service provider should provide you with the
access number, signaling tone, and other specifics when you
enroll.
Setting the voice mail signaling tone
If you are having trouble with your message waiting indicator
on your phone not illuminating when you have waiting
messages, you will need to contact your service provider and
inquire as to which type of message notification signal —
either Frequency Shift Keying (FSK) or Stutter Dial Tone
(SDT) — their service uses.
If your voice mail service uses an FSK message signal to
alert you of a new voice mail message, you must turn off the
Voice Mail Tone. If your voice mail service uses an SDT
message signal to alert you of new voice mail messages,
you can leave the Voice Mail Tone on.
Follow the instructions below to set up your cordless phone
settings:
1) Press MENU/SEL. Select the Global Setup menu, and
then the Voice Mail Tone submenu.
2) Move the cursor to set the SDT Voice Mail Tone to On or
Off.
3) Press MENU/SEL. You hear a confirmation tone.
Programming one-touch voice mail access
You can program your voice mail access number to the
21
Voice Mail key VOICEMAIL/MUTE on the handset so you
can get your messages at the touch of a button. Your voice
mail service provider will supply you with the access number
(this may be simply a phone number).
To edit the voice mail number, follow the steps below:
1) Press MENU/SEL.
2) Move the cursor to select the Handset Setup menu and
press MENU/SEL.
3) Move the cursor to select Edit Voice Mail and press
MENU/SEL.
4) Enter your personal access number (up to twenty digits).
If you need to have the phone wait before sending the
next digits, press PAUSE/REDIAL to insert a two-second
pause in the dialing sequence. For a longer pause, press
PAUSE/REDIAL multiple times. A P appears in the
display each time you press PAUSE/REDIAL and each
pause counts as one digit.
5) Press MENU/SEL when you are finished. You will hear a
confirmation tone.
Resetting the voice message waiting indicator
When you receive a new voice mail message, the
MESSAGE WAITING Indicator on the top of the handset
flashes and the voice mail icon appears in the handset
display. In the event your message waiting light gets out of
sync with your phone company’s voice messaging system,
you can manually reset it back to the “No messages waiting”
state.
1) Press and hold PAGE on the base for five seconds.
Note: The handsets connected to the base will start to
beep, however, keep pressing for five seconds.
2) A beep sounds and the message alert tone is reset.
22
Tone Dialing Switch Over
If your phone is set to pulse dialing, you can temporarily
switch to tone dialing after the call connects. This feature is
useful when you need tone dialing to use automated menu
systems, such as telephone bank tellers, telephone
prescription refills, customer support menus, etc. Make your
call normally. Once your call connects, press * on the
handset. Any digits you enter from then on will be sent with
tone dialing. When this particular call ends, the phone
automatically returns to pulse dialing.
Setting Up the Phonebook
The handset has its own phonebook that holds up to seventy
names and numbers. When a handset’s phonebook is full,
the handset beeps and shows Memory Full on the display.
You cannot add any names and numbers in that handset’s
phonebook until you delete some of the existing ones.
Creating Phonebook Entries
To store names and numbers in your phonebook, please
follow these steps:
1) With the phone in standby, press PHONEBOOK/RIGHT.
2) To create a new phonebook entry, press MENU/SEL.
Select the Create New menu. Edit Name appears.
3) Enter the name for this entry (EDIT NAME).
Use the keypad to enter a name for this entry; the name
can contain up to sixteen characters. (See Entering Text
from Your Handset on page 24 for instructions on
entering text.) If you do not want to enter a name for this
entry, your phone will store this entry as No Name. Press
MENU/SEL when you are finished.
4) Enter the number for this entry (EDIT NUMBER).
Once you have stored a name, Edit Number appears
23
next. Use the number keypad to enter the phone number;
the phone number can contain up to twenty digits. If you
need the phone to pause between digits when it’s dialing
(for example, to enter an extension or an access code),
press PAUSE/REDIAL to insert a two-second pause.
You will see a P in the display. You can also use more
than one pause together if two seconds is not long
enough. Each pause counts as one digit. Press
MENU/SEL when you are finished.
5) Assign a personal ring tone for this entry
(PERSONAL RING).
You can attach a special ring tone to each phonebook
entry; the phone will use this ring tone when this person
calls. Use UP and DOWN to select one of the seven
different ring tone options (see Selecting a Ring Tone on
page 13 for a complete list of ring tones). As you scroll
through the tones, you will hear a sample of each tone
(unless the handset ringer volume is set to off).
When you hear the ring tone you want to use, press
MENU/SEL. If you do not want to use a personal ring
tone for this phonebook entry, choose No Selection; the
phone will use your standard ring tone setting. (See page
14 to turn the personal ring on or off.)
6) You will hear a tone confirming that the new entry has
been stored, and Done! appears in the display.
Entering Text from Your Handset
You can use the number keypad on your handset to enter
text by referring to the letters printed on each number key.
When you press the number key in a text entry field, the
phone displays the first letter printed on the number key.
Press the number key twice to display the second letter and
three times to display the third.
• When [Aa] appears on the display, capital letters are
24
displayed first, then lower case letters, and then the
number on the key.
• When [aA] appears on the display, lower case letters are
displayed first, then the number on the key, and then
capital letters.
• When you input the first letter or a letter after a blank
space, the default mode is [Aa]. From the next letter, the
mode changes to [aA] automatically.
• You can switch back and forth the mode manually
between [Aa] and [aA]. Press *; the case (small/capital)
of the letter entered changes also.
If two letters in a row use the same number key, enter the
first letter, then use CID/RIGHT to move the cursor to the
next position to enter the second letter.
For example, to enter the word “Movies”:
1) Press 6 once to enter M.
2) Use CID/RIGHT to move the cursor to the right.
3) Press 6 three times to enter o.
4) Press 8 three times to enter v.
5) Press 4 three times to enter i.
6) Press 3 two times to enter e.
7) Press 7 four times to enter s.
8) Press MENU/SEL to end your text entry.
If you make a mistake while entering a name, use
CID/RIGHT or PHONEBOOK/LEFT to move the cursor to
the incorrect character. Press INT’COM/CLEAR to erase the
wrong character, and then enter the correct character. To
delete all characters, press and hold INT’COM/CLEAR.
Making a Call from the Phonebook
1) With the phone in standby, press PHONEBOOK/RIGHT
to open the phonebook.
2) Find the phonebook entry you want to call (see Finding a
Phonebook Entry on page 26).
25
3) Press TALK/FLASH to dial the number.
Note:
You can also press TALK/FLASH before you open
the phonebook. Find the phone number you want to
dial, and then press MENU/SEL.
Chain dialing from the phonebook
If you often have to enter a series of digits or a code number
during a call, you can save that code number to a phonebook
entry. When your call connects, just use the phonebook to
transmit the saved code number. (This is referred to as chain
dialing.)
1) Enter the code number (up to twenty digits) into the
phonebook (see Creating Phonebook Entries on page
23). Be sure to enter the code number into the
phonebook exactly as you would enter it during a call.
2) During a call, when you hear the prompt that tells you to
enter the code number, press PHONEBOOK/RIGHT.
3) Use UP or DOWN to select the phonebook entry that
contains the digits you want to send.
4) Press MENU/SEL. The phone sends the digits of the
code number exactly as you saved them in the
phonebook entry.
Finding a Phonebook Entry
Press PHONEBOOK/RIGHT to open the phonebook.
Phonebook entries are stored in alphabetical order. To scroll
through the phonebook from A to Z, press DOWN. To scroll
through the phonebook from Z to A press UP.
You can also use the letters on the number keys to jump to a
name that starts with that letter. For example, to search for
an entry beginning with the letter M, press 6 once. The
phonebook jumps to the first entry that begins with the letter
you entered; you can then use UP and DOWN to scroll to
other entries.
26
To close the phonebook and return to standby, press END. If
you are looking up a phonebook entry during a call and want
to close the phonebook, press PHONEBOOK/RIGHT again
instead of END.
Editing an Existing Phonebook Entry
1) With the phone in standby, press PHONEBOOK/RIGHT
to open the phonebook.
2) Find the entry you want to edit and press MENU/SEL.
3) Select Edit. Follow the steps for Creating Phonebook
Entries on page 23. If you do not wish to change the
information at any step, simply press MENU/SEL to go to
the next step.
Storing Caller ID or Redial Numbers in the
Phonebook
You can store Caller ID records or redial numbers in the
phonebook so you can use them later. Go to the Caller ID or
redial list and select the number you want to store. (If the
Caller ID information did not include the number, then you
will not be able to store it.)
1) With the phone in standby, press CID/LEFT to open the
Caller ID list or PAUSE/REDIAL to open the redial list.
2) Use UP and DOWN to scroll through the Caller ID
records or redial numbers. When you come to the
information you want to store, press MENU/SEL.
Note: If you need to add (or delete) a “1” to the
beginning of the Caller ID phone number, press *
(see page 29). If you need to add (or delete) the
stored area code to the Caller ID phone number,
press # (see page 30).
3) Select Store into PB. Edit Name appears. If the phone
number is already stored in memory, you will hear a beep,
and This data is already saved! appears in the display.
27
The number will not be stored.
4) Continue by following the steps for Creating Phonebook
Entries on page 23.
Deleting a Single Phonebook Entry
1) With the phone in standby, press PHONEBOOK/RIGHT.
2) Find the entry that you want to delete and press
MENU/SEL.
3) Select Delete. Delete Entry? appears in the display.
4) Move the cursor to select Yes.
5) Press MENU/SEL. You will hear a confirmation tone, and
Deleted! appears in the display.
Deleting all Phonebook Entries
1) With the phone in standby, press PHONEBOOK/RIGHT.
2) Press MENU/SEL, and then select Delete All. Delete All?
appears in the display.
3) Move the cursor to select Yes.
4) Press MENU/SEL. You will hear a confirmation tone, and
Deleted! appears in the display.
Using Caller ID, Call Waiting, and Redial
Lists
If you subscribe to Caller ID service from your phone
company, your phone will show you the caller’s phone
number and name (if available) whenever a call comes in. If
you subscribe to Caller ID on Call Waiting, the phone will
also show you the name and the number of any call that
comes in while you’re on the line.
Using the Caller ID List
You can store up to thirty Caller ID numbers in the handset.
Caller ID records are stored from newest to oldest. Once
28
your Caller ID list is full, the oldest record will be
automatically deleted when a new call is received. When you
have new Caller ID records (that is, records you have not
reviewed yet) and the phone is in standby, the handset will
display the number of new Caller ID calls received.
To open the Caller ID list, press CID/LEFT. The phone will
show the latest record.
Use UP and DOWN to scroll through the list. (New records
have an asterisk next to the received time.)
Making a Call from a Caller ID Record
1) With the phone in standby, press CID/LEFT to open the
Caller ID list.
2) Use UP and DOWN to find the Caller ID record you want
to dial.
3) If you need to add (or delete) a “1” to the beginning of the
displayed phone number, press *. If you need to add (or
delete) stored area code, press #.
4) Press TALK/FLASH to dial the number.
Note:
You can also press TALK/FLASH or before you
open the caller ID list. Find the phone number you
want to dial, and then press MENU/SEL.
What’s this “add or delete a 1” about?
• Any phone number in the Caller ID records might (or
might not!) have a “1” at the front, depending on how
different phone companies send the Caller ID
information.
• The phone dials the number exactly as it appears in the
Caller ID record.
• If the phone number is a long distance or toll call, but the
Caller ID record does not have a “1” in front of the
number, press * to add it. If the phone number is a local
or non-toll call, but the Caller ID record has a “1” in front
29
of the number, press * to delete it.
Seven-digit dialing
If you can make a local call by dialing only seven digits
instead of ten, you can tell the phone to hide your local area
code in the Caller ID list; any calls from outside your area
code will show all ten digits.
To program your local area code:
1) Press MENU/SEL.
2) Select the Global Setup menu, and then the Area Code
submenu.
3) Use the number keypad (0 through 9) to enter a
three-digit area code. If an area code has already been
stored, it appears in the display. Press INT’COM/CLEAR
to delete the stored code, and then enter a new one.
4) Press MENU/SEL. You will hear a confirmation tone.
• The phone uses the stored area code as a filter. When a
call comes in, the phone compares the incoming area
code to the code programmed on the phone. If the two
codes match, the handset hides the area code in the
Caller ID list.
• When you are reviewing the Caller ID list, you can show
the hidden area code by pressing #. Press # again to
hide the area code.
• When you dial from a Caller ID record or store a Caller ID
record in the phonebook, the phone dials or stores the
digits exactly as they appear on the display. If you need
to use ten digits, be sure to press # to show the area
code before you dial or store the number. (See page 27
to store a Caller ID record in the phonebook.)
Deleting Caller ID Numbers
To delete only one Caller ID number, press CID/LEFT when
the phone is in standby, and then find the number you want
30
to delete. Press MENU/SEL and select Delete Entry. When
the phone asks you to confirm, select Yes.
To delete all the Caller ID numbers, press CID/LEFT when
the phone is in standby. Press MENU/SEL and select
Delete All. When the phone asks you to confirm, select Yes.
Note:
When you delete a Caller ID number, you delete it
permanently.
Using Call Waiting
If you have Call Waiting service and a second call comes in
when you are on the phone, a call waiting tone will sound.
Press TALK/FLASH to accept the waiting call. There is a
short pause, and then you will hear the new caller. To return
to the original caller, press TALK/FLASH.
Note:
You must subscribe to Call Waiting service for this
feature to operate. Not all features are available in
all areas.
Using Multiple Bases and Handsets
The handset supplied with your phone can be registered to a
total of four different CT14 bases, and the base supports a
total of six cordless handsets. If you purchase two or more
CT14 packages, you can use the features in this section.
Any settings in the "Global Setup" or "Day & Time" menu are
applied to all registered handsets and the base. Only one
handset can change these settings at a time, and you have
to make sure another handset is not currently being used. If
you have multiple bases, the different bases have each
settings; select the base before changing these settings (see
Selecting the base on page 32).
Note:
To confirm how many bases the handset is
registered to, open the Select Base submenu
(follow the step 1 of Selecting the base on page 32).
Press END to close the list and return to standby.
31
Registering the handset to another base
To register a handset to another base:
1) Make sure the handset battery is fully charged.
2) Disconnect the AC adapter on the base you want to
register the handset to. Then press and hold PAGE while
you reconnect the adapter. Keep holding PAGE until the
CHARGE indicator starts to blink.
3) On the handset, press MENU/SEL. Select the Register
Base menu. Handset Registering will appear in the
display. (After step 2, you have thirty seconds to
complete this step 3 before the system returns to
standby.)
4) Wait approximately thirty seconds. Registration complete
will be displayed to indicate the handset has been
registered to the base and a handset ID will be
automatically assigned. The handset assigns its own ID
to this base, too. (Since the base ID is based on the order
in which the handset was registered to the different
bases, a base may have different IDs on each handset.)
If Registration failed appears in the LCD, please try these
steps again.
Note:
The handset will stay connected to the new base
until you select a different base (see below).
Selecting the base
After you register your handset to more than one base, you
can set the handset to automatically search for a new base if
the base it's currently connected is unavailable or out of
range. You can also manually select which base you want
the handset to connect to.
1) With the phone in standby, press MENU/SEL. Select the
Handset Setup menu, and then the Select Base
submenu.
32
2) Move the cursor to select the base you want to connect
to, or choose Auto to have the handset automatically
search for and select base.
3) Press MENU/SEL. Searching will appear in the display.
4) When the base is found, the handset will return to
standby. If the base is not found, “Searching” continues
to appear. You can repeat the procedure listed above to
return back to the original connection or to find the
different base.
Note:
You cannot change bases during a call.
Conferencing
If more than one handset is registered to a base, up to three
people can participate in a conference call. A three-way
conference call consists of an outside line and two handsets.
You can easily join a call already in progress. The handsets
must be currently connected to the same base (see
Selecting the base on page 32).
1) Press TALK/FLASH to join the call.
2) To hang up, return the handset to the base or press END.
3) The other party will still be connected to the call.
Privacy Mode
Privacy mode prevents other handsets (that are connected
to the same base) from interrupting your call. As long as your
handset is in privacy mode, other handsets can’t join your
call or make any calls of their own: their displays will show
Unavailable.
1) While on a call, press MENU/SEL.
2) Select Call Privacy. Privacy Mode On appears in the
display for two seconds; the privacy icon appears and
remains in the display until the feature is turned off.
To turn privacy mode off, repeat the procedure listed above.
Privacy Mode Off appears.
33
Note:
Privacy mode does not affect handsets that are
connected to a different base or extension phone.
Transferring a Call
If more than one handset is registered to a base, you can
transfer a call from one handset to another. The handsets
must be currently connected to the same base
(see page 32).
1) During a call, press INT’COM/CLEAR.
2) Use UP or DOWN to select the handset you want to
transfer the call to, and then press MENU/SEL. Select All
to page all other handsets. The call will automatically be
placed on hold, and a paging tone sounds. To cancel the
transfer, press TALK/FLASH.
3) When another handset accepts the transferred call, you
will be disconnected. If you want to rejoin the call, press
TALK/FLASH again.
Answering a transferred call
When a handset receives a call transfer, it sounds a paging
tone; handsets also show the ID of the handset that is paging.
To accept the call transfer:
1) To answer the page and speak to the transferring
handset, press TALK/FLASH or INT’COM/CLEAR.
Note: If Auto Talk is on, the handset will automatically
answer the page when you pick up the handset
from the base. If Any Key Answer is on, you can
also press any key on the handset’s dial pad.
2) To accept the call and speak to the caller, press
TALK/FLASH on the receiving handset.
3) When you accept the transferred call, the transferring
handset will be disconnected.
Only the first handset to answer the transfer page will be
connected to the call. If the transfer page is not picked up
34
within one minute, the operation will be canceled.
Using the Intercom
If more than one handset is registered to a base, you can
use the intercom to talk to another handset without using the
phone line. The handsets must be currently connected to the
same base (see page 32).
Making an intercom page
1) With the phone in standby, press INT’COM/CLEAR.
2) Use UP or DOWN to select the handset you want to talk
with, and then press MENU/SEL. Select All to page all
other handsets.
3) To cancel the intercom page, press END.
Notes: • Intercom paging will be cancelled if any of the
following things occur:
• You receive an outside call or an intercom page
while selecting the other handset.
• You do not select a handset within thirty seconds.
• Your handset is out of range (Out Of Range
appears in the display).
• The party does not answer the page within one
minute.
• The party is busy.
• The party is out of range (Unavailable appears in
the display).
Answering an intercom page
When the intercom page tone sounds, the display will show
the ID of the handset that is paging.
1) Press TALK/FLASH or INT’COM/CLEAR.
Note: If Auto Talk is on, the handset will automatically
answer the page when you pick up the handset
from the base. If Any Key Answer is on, you can
35
also press any key on the handset’s dial pad.
2) To hang up an intercom call, press END.
Copying Phonebook Entries to Another Handset
If more than one handset is registered to a base, you can
transfer phonebook entries from one handset to another
without having to re-enter names and numbers. You can
transfer one phonebook entry at a time or all phonebook
entries at once.
1) With the phone in standby, press PHONEBOOK/RIGHT.
2) To copy one entry, find the phonebook entry you want to
copy. Press MENU/SEL, and then select Copy.
To copy all entries, press MENU/SEL, and then select
Copy All.
3) Move the cursor to select the handset which you want to
transfer the entries to and then press MENU/SEL.
If you select Copy All, Are you sure? appears on the
display screen. Move the cursor to select Yes, and then
press MENU/SEL.
4) The phonebook entries will be transferred to the
designated handset. During the copy process, the
receiving handset shows Receiving and the ID of the
sending handset.
5) When the transfer is completed, Done! appears on the
handset.
Notes: • The handsets must be currently connected to the
same base (see page 32).
• If the handset you want to transfer to already has
seventy entries in its phonebook, you will hear a
beep, and Not enough memory in receiving unit
appears on the display.
• If the selected handset is out of range or data
transfer is cancelled, Unavailable appears in the
display. Phonebook listings will not be transferred.
36
Maintenance
Specifications
•
•
•
Operating temperature
32° F to 122° F (0° C to 50° C)
AC adapter
Part number:
77391-02
Input voltage:
100-240V AC, 50/60 Hz
Output voltage: 9V DC, 500mA
Battery pack
Part number:
80639-01
Capacity:
650mAh, 2.4V DC
Notes:
• Use only the supplied AC adapters.
• Be sure to use the proper adapter.
• Do not place the power cord where it creates a
trip hazard or where it could become chafed and
create a fire or electrical hazard.
• Do not place the base in direct sunlight or subject
it to high temperatures.
Note on Power Sources
Low battery alert
When the battery pack is very low, the phone is programmed
to eliminate functions in order to save power. When Low
Battery - Charge Handset appears in the handset display
and the phone is in standby, none of the keys will operate. If
you are on a call, complete your conversation as quickly as
possible, and return the handset to the cradle. The battery
pack needs to be charged when the empty battery icon
appears.
Cleaning the charging contacts
To maintain a good charge, clean the charging contacts on
the handset once a month. Dampen a cloth with plain water.
37
Gently rub the damp cloth over the charging contacts until all
visible dirt is removed. Dry the contacts thoroughly before
returning the handset to the cradle.
Caution:
Do not use paint thinner, alcohol, or other chemical products.
Doing so may discolor the surface of the telephone and
damage the finish.
Battery replacement and handling
When the operating time becomes short, even after a battery
is recharged, please replace the battery. With average use,
your phone’s battery should last approximately one year.
Caution:
• Use only the supplied battery pack.
• Do not remove the batteries from the handset to charge
them.
• Never throw the battery into a fire, disassemble, or heat
them.
• Do not remove or damage the battery casing.
Power Failures
During a power failure, you will not be able to make or
receive calls with the phone. To avoid damage from an
electrical spike when the power comes back on, we
recommend you unplug your phone during power outages.
38
Troubleshooting
Common Issues
If your phone is not performing to your expectations, please
try these simple steps first.
When you have
this problem...
The CHARGE
indicator won’t
illuminate when the
handset is placed in
the base.
Try...
• Checking the AC adapter
connection.
• Re-seating the handset in the base.
No handsets can
make or receive
calls.
• Checking the telephone cord
connection. If Check TEL Line
appears on the handset display, the
telephone cord may not be
connected correctly.
• Disconnecting the base AC adapter.
Wait a few minutes, and then
reconnect it.
• Changing the dial mode.
A single handset
can’t make or
receive calls (but
other handsets can).
• Moving the handset closer to the
base.
• Resetting the handset.
A handset can make
calls, but it doesn’t
ring or receive a
page.
• Making sure the ringer isn’t turned
off.
39
When you have
this problem...
Try...
A handset is not
working.
• Checking the battery pack
connection.
• Charging the battery for 15-20
hours.
• Resetting the handset.
A handset says
Unavailable.
• Moving the handset closer to the
base.
• Seeing if another handset has
Privacy Mode turned on.
• Making sure the base is plugged in.
The phone keeps
ringing when I
answer on an
extension.
• You may have to change the line
mode. Contact customer service for
more information.
No handsets will
display any Caller ID
information.
• Checking to see if the call was
placed through a switchboard.
• Asking your telephone company to
verify your Caller ID service is
current. There may be a problem
with your Caller ID service.
• Letting incoming calls ring at least
twice before answering.
Caller ID displays
briefly and then
clears.
• You may have to change the line
mode. Contact customer service for
more information.
40
When you have
this problem...
Try...
I can’t register a
handset at the base.
• Seeing if you already have 6
handsets registered to this base.
• Seeing if you already registered this
handset to 4 bases.
• Resetting the handset.
A handset doesn’t
communicate with
other handsets.
• Making sure all handsets are
registered to and currently
connected to the same base.
• Resetting the problem handsets.
I can’t transfer calls.
• Making sure all handsets are
registered to and currently
connected to the same base.
• Resetting the problem handsets.
I can’t get two
handsets to talk to
an outside caller.
• Checking to see that there are not
two handsets already using the
conference feature.
• Making sure another handset is not
in Privacy Mode.
• Making sure both handsets are
registered to and currently
connected to the same .
The MESSAGE
WAITING indicator
flashes, but there
are no new
messages.
• Resetting the MESSAGE WAITING
Indicator.
41
Weak or Hard to Hear Audio
If the caller’s voice sounds weak or soft, the signal might be
blocked by large metal objects or walls; you might also be
too far from the base, or the handset’s battery may be weak.
• Try adjusting the volume of the earpiece (see page 18) or
the audio tone (see page 18).
• Try moving around while you’re on a call or moving closer
to the base to see if the sound gets louder.
• Make sure the handset’s battery is fully charged.
Noise or Static on the Line
The most common cause of noise or static on a cordless
phone is interference: other wireless or electronic devices
can radiate energy that disturbs the radio signal between the
base and the handset (much like overhead power lines can
cause static on your car radio). Some common household
sources of interference are
• electrical appliances, especially microwave ovens
• computer equipment, especially wireless LAN equipment
and DSL modems
• radio-based wireless devices, such as room monitors,
wireless controllers, or wireless headphones or speakers
• large florescent light fixtures (particularly ones that give
off a “buzzing” noise)
• other services that use your phone line, like alarm
systems, intercom systems, or broadband Internet
service
For static on only one handset or in a specific location:
• Check nearby for one of the common interference
sources.
• Try moving the handset away from a suspected source,
or try moving the suspected source so it’s not between
the handset and the base.
42
For static on more than one handset:
• Check near the base for the source of interference.
• Try moving the base away from a suspected source, or
try turning off the source if possible.
• If you have any services that might use your phone line,
see if you need a filter on the phone line.
Installing a telephone line filter or DSL filter
Any broadband Internet service that uses your telephone line
might interfere with standard phones. The most common
type of these services, DSL, often causes static on your
telephone. Fortunately, an easy-to-install filter removes this
static from the line. Technicians who install DSL service
usually leave several filters for the customers; if you can’t
find them, call your DSL provider or look in any electronics
store.
Just plug the DSL filter into the telephone wall jack and then
plug your phone’s base into the filter. Make a test call to
make sure the noise is gone.
Traveling Out of Range
When the handset is in standby, the handset will display Out
Of Range.
During a call, if you move your handset too far from your
base, noise may increase. If you pass the range limit of the
base, the handset will beep, display Out Of Range, and then
go to standby. The base will maintain the connection for thirty
seconds after the handset goes out of range. If you move the
handset back within range of the base within thirty seconds,
press TALK/FLASH to pick up the call again.
Note:
If it is set to automatically select the available base,
the handset will begin searching for another base
thirty seconds after going out of range. (see
43
Selecting the base on page 32).
Changing the Line Mode for Multiple Extensions
Line mode refers to the method that telephones use to signal
each other that an extension is in use. Customer service
may recommend changing the line mode if you have any of
the following problems:
• Your phone keeps ringing after someone answers on an
extension phone.
• Your answering system doesn’t stop recording when you
answer on an extension phone.
• Caller ID displays briefly and then clears.
1) If you have multiple bases, select the base that is having
problems (see page 32).
2) Press MENU/SEL.
3) Select the Global Setup menu, and then the Set Line
Mode submenu.
4) If Instructed by Customer Service Press [select] appears.
Press MENU/SEL.
5) Move the cursor to select Type - A, Type - B, or Off.
6) Press MENU/SEL. You will hear a confirmation tone.
Resetting the Handset
If you are having trouble with a particular handset or if you
want to replace a handset, first clear the registration
information from the base and the handset.
If you have the base the handset is registered to:
1) Select the base you want to de-register the handset from
(see Selecting the base on page 32).
2) Press and hold END and # for more than five seconds.
Select Deregister HS.
3) Select the handset which you are operating, and then
press MENU/SEL.
44
4) The phone will ask you to confirm the deregistration.
Select Yes. The handset will clear its registration
information only from the base it is currently connected to,
and then delete the link to the base from its own memory.
If the handset cannot contact the base, it will display Out Of
Range. Make sure the handset is in range of the base and
the base is connected to power.
If you don’t have the base the handset is registered to:
1) Press and hold END and # for at least five seconds.
Select Base Unavailable.
3) Select the base which you want to de-register from, and
then press MENU/SEL.
4) The phone will ask you to confirm the deregistration.
Select Yes. The handset deletes its own base information
without contacting the base. If the handset was
registered to only one base, it displays Handset not
registered-place handset on base to register. See your
Owner's Manual for help. If the handset is still registered
to another base, it searches for the other base and then
returns to standby.
Re-registering the handset
After the handset is de-registered, you must re-register the
handset before you can use it.
1) Place the handset in the base cradle for several seconds.
2) When the handset has registered to the base, the LCD
will display Registration complete then show the handset
ID number.
If the display shows Registration failed, try the process
again.
45

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 45
Creator                         : CT14_OM_0912.doc - Microsoft Word
Create Date                     : 2008:09:12 18:21:18
Title                           : CT14_OM_0912.doc
Author                          : eng
Producer                        : Acrobat PDFWriter 5.0 Windows NT

EXIF Metadata provided by EXIF.tools