Uniden Bc125At Owners Manual
Uniden-Bc125At-Owner-S-Manual uniden-bc125at-owner-s-manual
BC125AT to the manual ac8d6ae9-da74-4a25-8b39-076f3e8c9aef
2015-05-27
: Uniden Uniden-Bc125At-Owners-Manual-725509 uniden-bc125at-owners-manual-725509 uniden pdf
Open the PDF directly: View PDF 
.
Page Count: 76
| Download | |
| Open PDF In Browser | View PDF |
BC125AT Owners Manual © 2012 Uniden America Corporation Fort Worth, Texas Printed in Vietnam U01UB370ZZC(0) Precautions Before you use this scanner, please read and observe the following. EARPHONE WARNING! Be sure to use only a monaural earphone with this scanner. You can also use an optional stereo headset. Use of an incorrect earphone or mono headset might be potentially hazardous to your hearing. The output of the phone jack is monaural, but you will hear it in both headphones of a stereo headset. Set the volume to a comfortable audio level coming from the speaker before plugging in the monaural earphone or headset. Otherwise, you might experience some discomfort or possible hearing damage if the volume suddenly becomes too loud because of the volume control or squelch control setting. This might be particularly true of the type of earphone that is placed in the ear canal. WARNING! Uniden does not represent this unit to be waterproof. To reduce the risk of fire or electrical shock, do not expose this unit to rain or moisture. Uniden® is a registered trademark of Uniden America Corporation. Close Call™ is a trademark of Uniden America Corporation. Contents Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 The FCC Wants You To Know. . . . . . . . . . . . . . . . . . . . . . . . . . 6 Scanning Legally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Feature Highlights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 USA Band Plan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Canada Band Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 INCLUDED WITH YOUR SCANNER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 SCANNING BASICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 What is Scanning?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 What is Searching?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Understanding Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 What is CTCSS/DCS?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Conventional Scanning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Simplex Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Repeater Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Understanding Banks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Channel Storage Banks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Service Search Banks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Custom Search Banks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Where To LEARN MORE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 SETTING UP YOUR SCANNER. . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Connecting the Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Connecting an Optional Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Connecting an Earphone/Headphone. . . . . . . . . . . . . . . . . . . . . . . . . 21 Connecting an Extension Speaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 ADJUSTING the Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 POWERING THE SCANNER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Installing Non-Rechargeable Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Installing Rechargeable Ni-MH Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Charging the Ni-MH Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 ABOUT YOUR SCANNER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 GETTING TO KNOW THE SCANNER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Turning On the Scanner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 A Look At The Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Setting Up Your Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Using the Scroll Control Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Adjusting the Squelch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Setting the Backlight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Adjusting the Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Setting the Charging Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Using the Keypad Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Setting the Beep Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Resetting the Scanner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 PC Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 PROGRAMMING CHANNELS. . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Programming Channel Text Tags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Setting CTCSS/DCS for a Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Setting Channel Modulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Setting the Priority Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Setting Channel Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Deleting Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Clearing a Bank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 SCANNING STORED CHANNELS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Priority Scan Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Manually Selecting a Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Locking Out Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Unlocking Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Unlock all Channels in Banks Currently Enabled for Scan . . . . . . . . . . . . 47 Service Search Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Service Search Receive/Hold Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Custom Search Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Custom Search Receive/Hold Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Quick Search Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Quick Search Receive/Hold Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Search Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Programming Custom Search Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Storing Found Search Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Locking Out Search Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Unlocking Search Frequencies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 CLOSE CALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Using the Close Call Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Selecting Close Call Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Close Call Only Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Set Close Call Bands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Close Call Alert. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Close Call Hits Bank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Close Call Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Close Call CTCSS/DCS Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 WEATHER OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Searching for a Weather Broadcast. . . . . . . . . . . . . . . . . . . . . . . . . . 63 Weather Alert Standby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Weather Alert Priority. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 65 RBRC INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 REFERENCES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 CTCSS Frequencies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 DSC Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Birdies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 One Year Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 The FCC Wants You To Know This scanner has been tested and found to comply with the limits for a scanning receiver, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This scanner generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this scanner does cause harmful interference to radio or television reception, which can be determined by turning the scanner on and off, you are encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the scanner and the receiver This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. Scanning Legally Your scanner covers frequencies used by many different groups, including police and fire departments, ambulance services, government agencies, private companies, amateur radio services, military operations, pager services, and wire-line (telephone and telegraph) service providers. It is legal to listen to almost every transmission your scanner can receive. However, there are some transmissions that you should never intentionally listen to. These include: • Telephone conversations (cellular, cordless, or other private means of telephone signal transmission) • Pager transmissions • Any scrambled or encrypted transmissions According to the Electronic Communications Privacy Act (ECPA), you are subject to fines and possible imprisonment for intentionally listening to, using, or divulging the contents of such a conversation unless you have the consent of a party to the conversation (unless such activity is otherwise illegal). This scanner has been designed to prevent the reception of cellular telephone transmissions and the decoding of scrambled transmissions. This is done to comply with the legal requirement that scanners be manufactured so they are not easy to modify to pick up these transmissions. Do not open your scanner’s case to make any modifications that could allow it to pick up transmissions that are illegal to monitor. Modifying or tampering with your scanner’s internal components or using it in a way other than as described in this manual could invalidate your warranty and void your FCC authorization to operate it. 7 In some areas, mobile use of this scanner is unlawful or requires a permit. Check the laws in your area. It is also illegal in many areas (and a bad idea everywhere) to interfere with the duties of public safety officials by traveling to the scene of an incident without authorization. Changes or modifications to this product not expressly approved by Uniden, or operation of this product in any way other than as detailed by this Operating Guide, could void your authority to operate this product. Introduction Thank you for purchasing a Uniden BC125AT Handheld Scanner. The scanner is versatile, compact, and easy to use. In addition to its standard scanning features, your scanner also includes Close Call™ RF capture technology designed to help you detect and identify strong local radio signals in your area. You can program up to 500 frequencies into the scanner's memory either manually or using optional computer software. The scanner lets you scan transmissions and is preprogrammed with service banks for your convenience. You can quickly search those frequencies most commonly used by police and other agencies, without tedious and complicated programming. The scanner gives you direct access to over 40,000 exciting frequencies. Use your scanner to monitor: • Police • Fire/Emergency • HAM Radio • Marine 8 • Railroad • Civil Air • Military Air • CB Radio • FRS/GMRS/MURS • Racing Feature Highlights 10 Channel Storage Banks - You can store up to 50 frequencies into each bank for a total of 500 frequencies so you can more easily identify calls. Close Call™ RF Capture Technology - you can set the scanner so it detects and provides information about nearby radio transmissions Close Call Do-Not-Disturb - checks for Close Call activity in between channel reception so active channels are not interrupted. Close Call Temporary Store - temporarily stores and scans the last 10 Close Call hits in the Close Call Hits bank. PC Programming - you can download information into the scanner and upload to the scanner via your personal computer. CTCSS and DCS Squelch Modes - rapid search for CTCSS/DCS tones/codes used during a transmission. You can identify up to 50 CTCSS tones and 104 DCS codes. Direct Access - lets you directly access any channel. Lock-Out Function - lets you set your scanner to skip over specified channels or frequencies when scanning or searching. 9 Temporary Lockout - makes it easy to temporarily lock out any channel or frequency. The lockout is cleared when you turn power off, then back on so you don’t have to remember to unlock the channels or frequencies later. Triple-Conversion Circuitry - virtually eliminates any interference from IF (intermediate frequency) images, so you hear only the selected frequency. Text Tagging - you can name each channel, using up to 16 characters per name. Service Banks - frequencies are preset in 10 separate Police, Fire/Emergency, Ham, Marine, Railroad, Civil Air, Military Air, CB Radio, FRS/GMRS/MURS, and Racing banks to make it easy to locate specific types of calls and search any or all of these banks. Priority Scan with Do Not Disturb - lets you program one channel in each bank (10 in all) and then have the scanner check each channel every 2 seconds while it scans the banks so you don’t miss transmissions on those channels. Do-Not Disturb keeps the scanner from interrupting transmissions during receiving. Priority Plus Scan - you can set the scanner so it scans only the priority channels. Scan/Search Delay/Resume - controls whether the scanner pauses at the end of the transmission to wait for a reply. You can set the Delay time for each Channel, Close Call Search, Custom Search, and Service search. You can also set a negative delay where the scanner stops on transmissions for a set time then automatically resumes. 10 Custom Search - lets you program up to 10 Custom Search Ranges and search any or all of these ranges. Quick Search - allows you to enter a frequency and start searching up or down from that frequency. Turbo Search - increases the search speed from 100 to 300 steps per second automatically for bands with 5 kHz steps. Search Lockouts - you can lock up to 200 search frequencies: 100 temporary frequencies and 100 permanent frequencies in Custom Search, Service Search, Close Call Search, or Quick Search Modes. Weather Alert Priority - the scanner scans active WX channels every 5 seconds to check for the presence of a 1050 Hz Weather Alert Tone. Weather Alert Standby - the scanner allows you to monitor for weather alerts broadcast on NOAA channels. Display Backlight - You can turn on/off the LCD backlight, set it operate on squelch only, keypress only, or both. Signal Strength Meter - shows the signal strength for more powerful transmissions. Flexible Antenna with BNC Connector - provides adequate reception in strong signal areas and is designed to help prevent antenna breakage. You can also connect an external antenna for better reception. Memory Backup - keeps the frequencies stored in memory for an extended time if the scanner loses power. 11 Three Power Options - let you power the scanner using the included two AA rechargeable or alkaline batteries or the supplied USB cable. Built-In Charger - allows you to charge Ni-MH batteries in the scanner using a USB port on any computer and the supplied USB cable. Key Confirmation Tones - You can turn on/off a tone that sounds when you perform an operation correctly or if you make an error. Key Lock - lets you lock the scanner's keys to help prevent accidental changes to the scanner's programming. Battery Save - works when there is no transmission for 1 minute in Scan Hold mode and any Search Hold mode (without Priority Scan). This feature turns off RF power for 1 second and turns on it for 300ms to extend the battery life. icon will blink in the display and a Battery Low Alert - the tone warns you every 15 seconds when the battery power gets low. BATT Frequency Range This table lists the frequency ranges, frequency steps, default modulation, and type of transmissions you can hear for each range. 12 USA Band Plan FREQUENCY (MHz) LOWER UPPER STEP (kHz) MODE BAND 25.0000 27.9950 5.0 AM Petroleum Products & Broadcast Pickup CB Class D Channel Business & Forest Products 28.0000 54.0000 5.0 NFM 10 Meter Amateur Band VHF Low Band 6 Meter Amateur Band 108.0000 136.9916 8.33 AM Aircraft Band 137.0000 150.7700 5.0 NFM Military Land Mobile 2 Meter Amateur Band Military Land Mobile VHF High Band Federal Government AM Military Air Band 150.7750 150.8125 7.5 150.8150 154.4525 7.5 154.4562 154.4787 7.5 154.4825 154.5125 7.5 154.5150 154.5250 5.0 154.5275 154.5350 7.5 154.5400 154.6075 7.5 154.6100 154.6475 7.5 154.6500 157.4475 7.5 157.4500 157.4650 5.0 157.4700 163.2450 7.5 163.2500 173.2000 12.5 173.2037 173.2100 6.25 173.2150 173.2200 5.0 173.2250 173.3875 12.5 173.3900 173.3962 6.25 173.4000 174.0000 5.0 225.0000 380.0000 12.5 13 FREQUENCY (MHz) LOWER 400.0000 UPPER 512.0000 STEP (kHz) MODE BAND 6.25 NFM Miscellaneous Federal Government Land Mobile 70 cm Amateur Band UHF Standard Band Canada Band Plan FREQUENCY (MHz) LOWER UPPER STEP (kHz) MODE BAND 25.0000 27.9950 5.0 AM Petroleum Products & Broadcast Pickup CB Class D Channel Business & Forest Products 28.0000 54.0000 5.0 NFM 10 Meter Amateur Band VHF Low Band 6 Meter Amateur Band 108.0000 136.9916 8.33 AM Aircraft Band 137.0000 174.0000 5.0 NFM Military Land Mobile 2 Meter Amateur Band Military Land Mobile VHF High Band Federal Government 225.0000 380.0000 12.5 AM Military Air Band NFM Miscellaneous Federal Government Land Mobile 70 cm Amateur Band UHF Standard Band 400.0000 512.0000 6.25 INCLUDED WITH YOUR SCANNER • BC125AT scanner with attached belt clip • Antenna • Rechargeable Ni-MH Batteries • USB cable 14 • Wrist strap If any of these items are missing or damaged, immediately contact your place of purchase or Uniden Customer Service at: (800) 297-1023, 8:00 AM to 5:00 PM, CST, Monday through Friday. Optional Accessories Contact your local Uniden Dealer or call the Uniden Parts Center at: (800)554-3988, 8:00AM to 5:00PM EST, Monday through Friday, for information about ordering these optional accessories. Note: USB cables are also available from the Uniden On-Line store. Visit http://www.uniden.com. SCANNING BASICS This section provides you with background on how scanning works. You don’t really need to know all of this to use your scanner, but some background knowledge will help you get the most from your BC125AT. What is Scanning? Unlike standard AM or FM radio stations, most two-way communications do not transmit continuously. Your BC125AT scans programmed channels until it finds an active frequency, then stops on that frequency and remains on that channel as long as the transmission continues. When the transmission ends, the scanning cycle resumes until the scanner receives another transmission. 15 What is Searching? The BC125AT can search for active frequencies. This is different from scanning because you are searching for frequencies that have not been programmed into the scanner. When you select frequency bands to search, the scanner searches for any active frequency within the lower and upper limits you specify. When the scanner finds an active frequency, it stops on that frequency as long as the transmission lasts. If you think the frequency is interesting, you can store it into one of the banks. If not, you can continue to search. Understanding Scanning What is CTCSS/DCS? Your scanner can monitor systems using a Continuous Tone Coded Squelch System (CTCSS) and Digital Coded Squelch (DCS) system, which allows the squelch to open only when the tone you have programmed with a specific frequency is received along with a transmission. CTCSS and DCS are sub-audible tone signaling systems sometimes referred to as PL or DPL (Motorola’s trademarked terms for Private Line and Digital Private Line respectively). CTCSS and DCS are used only for FM signals and are usually associated with both amateur and commercial two-way frequencies. These systems make use of a special sub-audible tone that accompanies a transmitted signal. CTCSS and DCS are used for many purposes. In many cases, CTCSS and DCS are used to restrict access to a commercial repeater, so that only those units which transmit the correct tone along with their signal can “talk” to the repeater. 16 CTCSS and DCS are also used in areas that receive interference where there are several stations with output frequencies close to each other. When this occurs, you might hear multiple communications on the same frequency. The stations might even interfere with each other to the point where it is impossible to clearly receive any of the stations. Your scanner can code each received frequency with a specific sub-audible CTCSS or DCS frequency or code. Then, when you receive multiple signals, you only hear the transmission with the CTCSS or DCS tone you programmed. If you do not receive the correct tone with a signal, the scanner’s squelch remains closed and you hear nothing. Refer to the Reference section of this manual for tables showing the available CTCSS frequencies and DCS codes. Conventional Scanning Conventional scanning is a relatively simple concept. Each group of users in a conventional system is assigned a single frequency (for simplex systems) or two frequencies (for repeater systems). Any time one of them transmits, their transmission always goes out on the same frequency. Up until the late 1980’s this was the primary way that radio systems operated. Even today, there are many 2-way radio users who operate using a conventional system: • Aircraft • Amateur radio • FRS/GMRS users • Many business radio users 17 When you want to store a conventional system, all you need to know is the frequencies they operate on. When you are scanning a conventional system, the scanner stops very briefly on each channel to see if there is activity. If there isn’t, the scanner quickly moves to the next channel. If there is, then the scanner pauses on the transmission until it is over. Simplex Operation Simplex systems use a single frequency for both transmit and receive. Most radios using this type of operation are limited to line-of-sight operation. This type of radio is frequently used at construction job sites, and with inexpensive consumer radios such as GMRS/FRS radios. The range is typically 1-8 miles, depending upon the terrain and many other factors. Repeater Operation Repeater systems use two frequencies: one transmits from the radio to a central repeater; the other transmits from the repeater to other radios in the system. With a repeater-based system, the repeater is located on top of a tall building or on a radio tower that provides great visibility to the area of operation. When a user transmits (on an input frequency), the signal is picked up by the repeater and retransmitted (on an output frequency). The user’s radios always listen for activity on the output frequency and transmit on the input frequency. Since the repeater is located very high, there is a very large line of sight. Typical repeater systems provide coverage out to about a 25-mile radius from the repeater location. 18 Understanding Banks Channel Storage Banks To make it easier to identify and select the channels you want to listen to, the 500 channels are divided into 10 channel storage banks containing 50 channels each. You could use each channel storage bank to group frequencies by department, location, area of interest, or any other way you prefer. You can listen to any or all of the banks by using the number keys to turn them on or off. Service Search Banks The scanner is preprogrammed with many of the frequencies allocated to Police, Fire/Emergency, Ham, Marine, Railroad, Civil Air, Military Air, CB radio, FRS/GMRS/MURS, and Racing services. There are 10 banks allocated for these searches that can be used just like the channel storage banks to search these frequencies in Service Search mode. Custom Search Banks Custom Search Banks let you program and search 10 custom search ranges. During custom search, the scanner starts searching with the lowest frequency in the search range you select to the highest frequency in the range. You can search any or all of these ranges by turning each search bank on or off just like channel storage banks in Search mode. Where To LEARN MORE By itself, this manual really only provides part of what you need to know to have fun scanning – how to program and use the scanner. The website, http://www.radioreference. com, is the Internet's premier source for user-supported radio 19 system information. This web sites is not affiliated with Uniden Corporation. For more information about Uniden and our other products, visit http://www.uniden.com. SETTING UP YOUR SCANNER These guidelines will help you install and use your new scanner. If your scanner receives interference or electrical noise, move the scanner or its antenna away from the source. You might also try changing the height or angle of the rubber antenna. To improve the scanner’s reception, use an optional external antenna designed for multiband coverage. (You can purchase this type of antenna at a local electronics store). If the optional antenna has no cable, use 50 ohm coaxial cable for lead-in. An adapter plug might be necessary for the optional antennas. Use an optional mono earphone or stereo headset with proper impedance for private listening. Read the precautions on the inside front cover of this Owners Manual. Do not use the scanner in high-moisture environments such as the kitchen or bathroom. Avoid placing the scanner in direct sunlight or near heating elements or vents. Connecting the Antenna 1. 20 Align the slots around the antenna's connector with the tabs on the scanner's BNC connector. 2. Slide the antenna's connector down over the scanner's connector. 3. Rotate the antenna connector's outer ring clockwise until it locks into place. Connecting an Optional Antenna The scanner's BNC connector makes it easy to connect a variety of optional antennas, including an external mobile antenna or outdoor base station antenna. Note: Always use 50-ohm, RG-58, or RG-8, coaxial cable to connect an outdoor antenna. If the antenna is over 50 feet from the scanner, use RG-8 low-loss dielectric coaxial cable. If it is less than 50 feet, use RG-58. You can get a BNC adapter at local electronics stores. Connecting an Earphone/Headphone For private listening, you can plug a 1/8-inch (3.5 mm) miniplug earphone or stereo headphones (not supplied) into the headphone jack on top of your scanner. This automatically disconnects the internal speaker. Connecting an Extension Speaker In a noisy area, an optional extension speaker, positioned in the right place, might provide more comfortable listening. Plug the speaker cable's 1/8-inch (3.5-mm) mini-plug into your scanner's jack. WARNING! If you connect an external speaker to the scanner's headphone jack, never connect the audio output line to a power supply and ground. This might damage the scanner. 21 ADJUSTING the Belt Clip The factory-attached belt clip makes it easier to carry the scanner. Use a Phillips screwdriver to adjust (loosen) the mounting screws or remove the belt clip completely. POWERING THE SCANNER You can power the scanner using alkaline (ALK) nonrechargeable batteries (not supplied) or the included Nickel Metal-Hydride (Ni-MH) rechargeable batteries. [Uniden provides a USB cable to charge the Ni-MH batteries on initial installation and to recharge them through your computer (or through a power adapter that provides USB charge power (not included, but available at many retailers).] Inside the battery compartment is a switch to set the unit to either ALK or Ni-MH. Warning! Non-rechargeable batteries can get hot or burst if you try to recharge them. Cautions: flashes in the display and the scanner beeps • When every 15 seconds, recharge or replace the batteries. BATT • Use only fresh batteries of the required size and recommended type. • Always remove old or weak batteries. Batteries can leak chemicals that destroy electronic circuits. • Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities. 22 Installing Non-Rechargeable Batteries 1. Make sure the power is turned off. 2. Slide the battery compartment cover off. 3. Use a pointed object such as a ballpoint pen to set the battery selection switch inside the compartment to ALK. 4. Insert the batteries as indicated by the polarity symbols (+ and -) marked inside the battery compartment. 5. Replace the battery compartment cover. Installing Rechargeable Ni-MH Batteries You can also use two Ni-MH rechargeable batteries to power your scanner. The Ni-MH batteries included with your unit are not fully charged; you must charge them completely after you install them into your scanner. See Charging the NiMH Batteries, page 24, for details. 1. Make sure the power is turned off. 2. Slide the battery compartment cover off. 3. Use a pointed object such as a ballpoint pen to set the battery selection switch inside the compartment to Ni-MH for Nickel Metal-Hydride batteries. 4. Install two batteries in the compartment as indicated by the polarity symbols (+ and -) marked inside and replace the cover. Notes: • To prevent damage to Ni-MH batteries, never charge them in an area where the temperature is above 113°F (45°C) or below 40°F (4°C). 23 • For longer operation, you can get higher capacity Ni-MH batteries at your local electronics store. This type of battery takes longer to recharge. Charging the Ni-MH Batteries The scanner has a built-in circuit that charges the included Ni-MH batteries when a USB cable connects it to a computer (NOT to a USB hub) or to an AC or DC adapter that provides USB charging power. Verify that the battery selection switch is set to Ni-MH and that only Ni-MH rechargeable batteries are inserted in the scanner before connecting it to your computer. Caution: Never attempt to charge non-rechargeable batteries or install non-rechargeable batteries when the battery selection switch is set to Ni-MH. The USB cable will only charge the batteries if the scanner is turned off. 1. Be sure the scanner is turned off. It will recharge only if it is turned off, even with the USB cable connecting it to a computer. 2. Connect the included USB cable to the scanner’s USB port. 3. Connect the other end of the USB cable to the computer's USB port or to an AC or DC adapter that provides USB charging power. NOTE: If you connect to a computer's USB port, the PC will prompt you for the drivers for your scanner. To download and install these drivers, go to http://info.uniden.com/UnidenMan4/BC125AT. 4. 24 The scanner displays Charging while it charges the batteries and Charge Complete when the Ni-MH batteries are completely charged. Different status messages may display depending on the battery type and scanner status: USB Message Batt. Type Meaning Scanner Cond. Charging Ni-MH Scanner is charging. Off No Battery None NO batteries in scanner. Off Charge Complete Ni-MH Unit is charged. Off Charge Off Alk./NiMH Scanner is not charg- Off ing (Battery selection switch is set to Alk.) Battery Error Ni-MH Batteries cannot be charged (dead battery). Off Illegal Voltage Ni-MH USB external power is out of range. Off See also Setting the Charging Timer, page 35. If the batteries are good, the scanner charges the batteries. and it operates normally. If the scanner cannot immediately determine if the batteries are good and can be charged, it checks them and displays the battery icon. If the scanner judges the batteries are good, the scanner starts charging and the battery icon disappears. If it cannot regard the batteries as good in 60 seconds, the scanner stops checking and the battery icon blinks. 25 ABOUT YOUR SCANNER We use a few simple terms in this manual to explain the features of the scanner. Familiarize yourself with these terms and the scanner's features, and you can put the scanner to work for you right away. Simply determine the type of communications you want to receive, then set the scanner to search those communications. A frequency, expressed in kHz or MHz, is the tuning location of a station. To find active frequencies, you use the search function or refer to a frequency reference. Besides searching within a selected frequency range, you can also search your scanner's service banks. Service banks are preset groups of frequencies categorized by the type of services that use those frequencies. For example, many amateur radio frequencies are located in the HAM service bank. When you search and find a desired frequency, you can store it into a programmable memory location called a channel. Channels are grouped into channel storage banks. The scanner has 10 channel storage banks and each bank has 50 channels. You can scan the channel storage banks to see if there is activity on the frequencies stored there. GETTING TO KNOW THE SCANNER If your scanner's keys seem confusing at first, the following information should help you understand each key's function. Your scanner's keys have various functions labeled on the key tops and below the keys. The keys operate in Normal mode and Function mode. Pressing Func puts the scanner into Function 26 mode for 3 seconds and then returns to Normal mode. The scanner displays F . During that 3 seconds you can press other keys and operate that function. Pressing Func again before 3 seconds returns to Normal mode and the F icon disappears. In Normal mode the F icon is not displayed. WEATHER USB PORT CURSER LEFT/RIGHT DECIMAL/ CLEAR FUNCTION SCROLL CONTROL PROGRAM/ ENTER HEADSET JACK PRIORITY BEEP ANTENNA HOLD/ CLOSE CALL SCAN LOCK OUT/ KEY LOCK SEARCH/ SERVICE SEARCH POWER/ BACKLIGHT Key/ Icon Press to... Press Func and this key to... 1/Pri Enter 1. Enter the Priority menu. 3/WX Enter 3. Enter the Weather menu. 6/> • Enter 6. • Scroll right in Edit Tag mode. NA . Clr • Enter a decimal point. • Input a space in a text string. NA 27 Key/ Icon Press to... Press Func and this key to... func • Enter Function mode for 3 seconds. • Return to Normal mode from Function mode. NA Hold/ • Hold on a current channel. • Release hold and resume scanning/searching. • Monitor an unprogrammed frequency after you have entered it. • Access a channel directly after you have entered it. Enter the Close Call menu. Scan Enter or resume Scan mode. NA Srch/ Svc Start Custom Search. Start Service Search. L/O/ • Temporarily lock out a channel Lock or unlock the keypad. or search frequency (press once). • Permenantly lock out a channel or search frequency (press twice). • Unlock a locked out channel or search frequency. • Unlock all locked out settings of the current channel bank (press and hold). 28 Key/ Icon Press to... Press Func and this key to... • Turn scanner on and off (press and hold). • Turn backlight on and off. Enter the Display/Charge menu. Pgm/E • Select input data or a menu item. • Access a channel through its channel number. • Enter Channel Programming menu. • Quickly save frequencies in various modes. 4/< • Enter 4. • Scroll left in Edit Tag mode. NA 7/Beep Enter 7. Toggle the Keybeep setting. / Note: Turn Scroll Control to scroll up and down through menu selections. Turning On the Scanner Note: Make sure the scanner's antenna is connected before you turn it on. 1. You can select the band plan (USA or Canada) when you for 1 turn on the scanner. When you press and hold second to turn on the scanner, also press and hold 1 for USA or 2 for Canada. The opening screen displays, followed by the copyright notice. 29 2. If the scanner is new or has been reset, the default mode is Scan Hold with all banks enabled and Close Call DoNot-Disturb active. Otherwise, the scanner displays the last mode the scanner was in before it was powered down. A Look At The Display The display has indicators that show the scanner's current operating status. The display information helps you understand how your scanner operates. Note: Not all of these icons may appear at the same time. 15 16 14 14 13 12 11 F HOLD TL/O 1 Channel Name 2 CH0001 3 P 4 B N K 1 2 3 4 5 6 7 8 9 0 C WX 6 8 NFM 5 1 6 2. 5 2 5 0 PRI+ ↑ C254. 1 7 10 9 Item Meaning 1 • Channel Name in Scan/Scan Hold mode. • Custom/Service Search Bank Name. • Quick Search in Quick Search mode. • Close Call Hits in Scan/Scan Hold mode. • Close Call in Close Call Only mode. • WX Scan in Weather Scan mode. • WX Alert Standby in WX Alert Standby mode. 30 Item Meaning 2 • Scan in Scan mode. • CC Search in Close Call Only mode. • Channel Number and Frequency. • Searching Frequency. 3 P identifies a Priority channel. 4 • BNK/SVC/SRC/BND shows banks/bands enabled for Scan/Service Search/Custom Search/Close Call Only mode. • C is for the Close Call Hits bank. 5 AM/FM/NFM shows channel/frequency modulation. 6 • PRI indicates Priority Scan. • PRI indicates Priority Do-Not-Disturb. • PRI+ indicates Priority Plus Scan. 7 Shows any CTCSS/DCS tone/code received. 8 WX indicates Weather Priority is on. 9 • indicates Close Call Priority. • indicates Close Call Do-Not-Disturb. 10 11 12 ↑or ↓ indicates the scan/search direction. BATT indicates the batteries are low. indicates the key lock is enabled. 13 indicates the signal strength. 14 • TL/O indicates temporary lock out. • L/O indicates permanent lock out. 31 Item Meaning 15 • Hold on a channel. • Release hold and resume scanning. 16 Indicates Function mode. Setting Up Your Scanner When you turn on your scanner for the first time, you can set your screen display preferences as well as other elements such as squelch levels, volumes, brightness, etc. Using the Scroll Control Knob Turn the Scroll Control knob on top of the BC125AT to: • Select channels • Adjust volume • Adjust squelch • Set display settings • Selects characters for text tagging • Scroll up or down through menu options • Change channels/frequencies in Hold mode • Resume scanning Press the Scroll Control knob to select a setting. Note: Pressing SCROLL CONTROL is the same as pressing Pgm/E on the keypad in Menu mode. Adjusting the Volume 1. 32 Press Scroll Control; The volume level indicator and battery voltage display. 2. Turn Scroll Control to adjust the volume level from 0 to 15. 3. Press Scroll Control to set the volume. 4. To exit Volume Level mode, press Scroll Control again or wait 10 seconds to return to the previous mode. Adjusting the Squelch To adjust the squelch level, press Func, then press Scroll Control. When the squelch level indicator and battery voltage appear, turn Scroll Control to change the squelch level from 0 to 15. 1. Press Func, then press Scroll Control. The squelch level indicator and battery voltage appears. 2. Turn Scroll Control until the audio mutes. If the scanner picks up unwanted partial signals or very weak transmissions, increase the Squelch setting to increase the signal level required to open squelch. To listen to a weak or distant station, decrease the Squelch setting. 3. Press Scroll Control to set the desired level and return to the previous mode. Setting the Backlight Press to turn on the backlight on and off. to view the Display/Charge menu. 1. Press Func and 2. From this menu, scroll to Set Backlight from the submenus. Press SCROLL CONTROL. 3. Scroll to select one of the following settings: • Always Off - Backlight is always off. 33 • Always On – Backlight is always on. • On with Squelch - Backlight is on while squelch is open and until delay expires. • On with Keypress - Backlight is on for 10 seconds after any key is pressed. • Keypress+Squelch – Both above-mentioned "Squelch" and "Keypress." • < Back - Return to previous menu. 4. Press Pgm/E (or press SCROLL CONTROL) to save and return to the previous menu. (Default = Always Off ) 5. Press . Clr to exit. Notes: If the backlight is set to Always On when is pressed, the backlight is turned off and the backlight setting is then set to Always Off. If the backlight is set to Always Off when is pressed, the backlight is turned on and the backlight setting is then set to Always On. Adjusting the Contrast This submenu of the Display/Charge menu controls the display’s contrast (how light or dark it appears) for different viewing conditions. There are 15 contrast settings. You see the contrast change as you scroll through the settings. 1. To adjust the contrast, press Func then Charge menu displays 2. Scroll to Set Contrast and press Pgm/E. 3. Scroll to see the contrast settings. 34 ; the Display/ 4. When you have selected a setting, press Pgm/E to set it and return to the previous menu. 5. Press . Clr to exit. Setting the Charging Timer The Charging Timer menu is also a submenu of the Display/ Charge menu. It sets how long the scanner will charge the batteries when you plug the supplied USB cable into a USB port and connect it to your scanner. WARNING: The Charging Timer will reset to the set charging time every time you plug the USB cable into the scanner or charge the batteries while the USB cable is connected. 1. To set the Charging Timer press Func then Display/Charge menu. 2. Scroll to Set ChargeTime and press Pgm/E. 3. Scroll to 1-16 (hours) (default = 14 hours) and press Pgm/E to save and return to the previous menu. to view the Suggested maximum charging time for Ni-MH batteries: 1500mAh 9 hours 1800mAh 11 hours 2000mAh 12 hours 2100mAh 13 hours 2200mAh 13 hours 2300mAh 14 hours 2500mAh 15 hours 35 2700mAh 16 hours Note: The batteries will take longer to charge when the scanner is in use. 4. Press . Clr to exit. Using the Keypad Lock Use the scanner's keypad lock to protect it from accidental program changes. When the keypad is locked, only Func, Hold, , , and Scroll Control (volume only) operate. Press Func then L/O to toggle the keypad lock on and off. The scanner displays Keypad Lock On or Keypad Lock Off. Setting the Beep Tone Press Func then Beep/7 (Default = ON) to toggle the keypress confirmation tone on or off. Resetting the Scanner Warning: Resetting the scanner clears all data and settings you have entered. You cannot restore user programmed data that has been deleted. You can, at a last step, restore only the original factory data. 1. Press and hold the 2, 9, and Hold keys and turn on the scanner. 2. The scanner clears all data and returns to the initial setting. All Memory Clear displays. PC Programming Connect your scanner to your PC through the USB cable to: • Program channels into the scanner 36 • Set any setting When you connect your scanner to your PC, a series of screens will appear to assist you. USB drivers and programming software are available for download from http://info.uniden.com/UnidenMan4/BC125AT. PROGRAMMING CHANNELS Now that you have configured your scanner, you are ready to start using your scanner’s preprogrammed service banks, the custom search banks, the Close Call feature, or the Weather Scan/Alert feature. You can also program your channel memories or re-program your 10 custom search bank memories. Before the scanner can begin scanning, you must program a frequency into at least one channel. 1. To select a channel, press Hold then enter the channel number (1-500). 2. Press Pgm/E to enter the Channel menu. (You can also press Hold and scroll to the channel; press Func then Pgm/E.) Note 1: Turning Scroll Control in Function mode will allow you to select the first channel in each bank. Note 2: You can quickly store frequencies in Scan Hold mode by entering the frequency and pressing Pgm/E. 3. Scroll to highlight Enter Frequency and press Pgm/E. You will see the channel number and currently programmed frequency. (To return to the previous screen, press . Clr.) 37 4. Use number keys and . Clr for a decimal to enter the frequency. If you make a mistake, press . Clr to clear the display. Press Pgm/E to store the frequency and return to the Channel menu. 5. Press . Clr to return to the last screen. The scanner automatically rounds the entered number to the nearest valid frequency. For example, if you enter 151.473 (MHz), your scanner accepts it as 151.475. If you entered an invalid frequency, Out of Band appears and the scanner beeps three times. Press . Clr and enter a valid frequency. If you enter a frequency that has already been entered elsewhere, the scanner displays the channel number and Frequency Exists – Confirm? appears. If you entered the frequency by mistake, press . Clr then enter the correct frequency. To enter the frequency anyway, press Pgm/E to accept. The smallest channel is displayed when two or more duplication channels exist. Programming Channel Text Tags You can customize your channels by programming text tags (up to 16 characters in length) for easier channel frequency identification. The default tag is the bank number followed by the channel number in the bank. 1. 38 To select a channel, press Hold and then enter the channel number. 2. Press Pgm/E to enter the Channel menu. (You can also press Hold and scroll to the channel; press Func then Pgm/E.) 3. Scroll to select Edit Tag and press Pgm/E. 4. Turn Scroll Control to choose the characters, pressing > or < to move the cursor to the right or left. If you make a mistake, press . Clr to clear the last character. Press . Clr twice to clear all characters. To cancel and exit, press L/O. 5. Press Pgm/E to save the tag and return to the Channel menu. Setting CTCSS/DCS for a Channel You can store a CTCSS tone or DCS code, set the scanner to search for tones/codes, have the scanner open squelch on any tone/code, or have the squelch only open if no CTCSS/DCS is detected for any channel. (Default = Off ) 1. To select a channel, press Hold and then enter the channel number. 2. Press Pgm/E to enter the Channel menu. (You can also press Hold and scroll to the channel; press Func then Pgm/E.) 3. Scroll to select Set CTCSS/DCS and press Pgm/E. 4. Scroll to select one of the following options: • Off - the scanner ignores all tones and opens squelch on any signal 39 • CTCSS - the scanner prompts the user for the appropriate tone. Squelch will open for this channel only if the tone matches. • DCS - the scanner prompts the user for the appropriate code. Squelch will open for this channel only if the code matches. • CTCSS/DCS Search - the scanner displays any tone/ code being used, but opens squelch on any signal. • No Tone - indicates that the channel squelch will only open if no CTCSS/DCS is detected. •
Source Exif Data:File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.2.2-c063 53.352624, 2008/07/30-18:12:18 Create Date : 2012:08:01 10:04:55-05:00 Metadata Date : 2012:08:01 10:05:09-05:00 Modify Date : 2012:08:01 10:05:09-05:00 Creator Tool : Adobe InDesign CS4 (6.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 7254 bytes, use -b option to extract) Instance ID : uuid:efd9acaf-22ab-47dc-b888-3bc0109ec2db Document ID : xmp.did:7EC3FE4FCF206811B39FDAF3CEB6BEA9 Original Document ID : xmp.did:F656357FE6D3E0118A2DE42CC6E34F51 Rendition Class : proof:pdf History Action : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:F656357FE6D3E0118A2DE42CC6E34F51, xmp.iid:F756357FE6D3E0118A2DE42CC6E34F51, xmp.iid:F856357FE6D3E0118A2DE42CC6E34F51, xmp.iid:9EC867EA0FDFE011B15ABD2212773456, xmp.iid:51C081B615DFE011A235FDBDEC476FF4, xmp.iid:593956A525EAE011A51ED1A2656B098E, xmp.iid:EE0B76046CEBE0119F30EB9607CDD460, xmp.iid:7F202E8E11EDE011886AEAB15AB62992, xmp.iid:80202E8E11EDE011886AEAB15AB62992, xmp.iid:104DD8A7CAEDE011AA25DF1D70E674DD, xmp.iid:1075FD0CCEEDE011BC8BFD1E7C14D5D5, xmp.iid:53317420D8EDE011BBA9BC62C5BD8212, xmp.iid:CB721DFCDEEDE011B0D9BA4062AF3B85, xmp.iid:74F19BB79CEEE011AD83AA033A485916, xmp.iid:A395981E4FF0E0119902A1FC4F722C27, xmp.iid:A495981E4FF0E0119902A1FC4F722C27, xmp.iid:935F396313F1E01193E4B77D88B205B8, xmp.iid:945F396313F1E01193E4B77D88B205B8, xmp.iid:955F396313F1E01193E4B77D88B205B8, xmp.iid:965F396313F1E01193E4B77D88B205B8, xmp.iid:C0F8D1028CF2E011AD7EE3B639B87664, xmp.iid:50DE7D23B1F2E0119FDA881964249DD2, xmp.iid:51DE7D23B1F2E0119FDA881964249DD2, xmp.iid:52DE7D23B1F2E0119FDA881964249DD2, xmp.iid:53DE7D23B1F2E0119FDA881964249DD2, xmp.iid:54DE7D23B1F2E0119FDA881964249DD2, xmp.iid:05F622DCF3F2E0119ADD8202CD62CA50, xmp.iid:06F622DCF3F2E0119ADD8202CD62CA50, xmp.iid:0401FC4E3EF3E0118FF5FEBEF4895015, xmp.iid:B2C7CAEC6CF3E01187E5C30F3E5EA811, xmp.iid:B3C7CAEC6CF3E01187E5C30F3E5EA811, xmp.iid:1ECF71FA23F4E011A0429950C0280DD4, xmp.iid:1FCF71FA23F4E011A0429950C0280DD4, xmp.iid:7A20522DAFF5E011AB1BB44EA8BFAB84, xmp.iid:F826B180FFF8E0118B87B45635F78DD4, xmp.iid:F926B180FFF8E0118B87B45635F78DD4, xmp.iid:AD80538594FAE011B30AF6124772581C, xmp.iid:627FFFDB29FCE011A7D2BDFD9E58DEC1, xmp.iid:7914A25831FCE0119BDBCB89C91117B6, xmp.iid:7A14A25831FCE0119BDBCB89C91117B6, xmp.iid:C1D9D2F4F6FFE011A61AE681DB457B48, xmp.iid:C2D9D2F4F6FFE011A61AE681DB457B48, xmp.iid:C3D9D2F4F6FFE011A61AE681DB457B48, xmp.iid:C4D9D2F4F6FFE011A61AE681DB457B48, xmp.iid:C1EF0146CE00E111B7A3982EC761C477, xmp.iid:C2EF0146CE00E111B7A3982EC761C477, xmp.iid:C3EF0146CE00E111B7A3982EC761C477, xmp.iid:C4EF0146CE00E111B7A3982EC761C477, xmp.iid:55DEB0598001E111B9FECB745361F5A4, xmp.iid:C16A4701D803E11197E0DD672762F7AD, xmp.iid:C26A4701D803E11197E0DD672762F7AD, xmp.iid:61EB61D89404E111A6658F7EBC2526E6, xmp.iid:62EB61D89404E111A6658F7EBC2526E6, xmp.iid:63EB61D89404E111A6658F7EBC2526E6, xmp.iid:64EB61D89404E111A6658F7EBC2526E6, xmp.iid:2D28FA3D6448E111B7C6FBBFD16E649C, xmp.iid:2E28FA3D6448E111B7C6FBBFD16E649C, xmp.iid:5A12966E544CE11192DAD1552C384A9B, xmp.iid:5B12966E544CE11192DAD1552C384A9B, xmp.iid:5C12966E544CE11192DAD1552C384A9B, xmp.iid:5D12966E544CE11192DAD1552C384A9B, xmp.iid:5E12966E544CE11192DAD1552C384A9B, xmp.iid:ED86E2D3624CE11192DAD1552C384A9B, xmp.iid:EE86E2D3624CE11192DAD1552C384A9B, xmp.iid:2EEE9D055D20681192B09DB5CE58D61F, xmp.iid:2FEE9D055D20681192B09DB5CE58D61F, xmp.iid:30EE9D055D20681192B09DB5CE58D61F, xmp.iid:31EE9D055D20681192B09DB5CE58D61F, xmp.iid:32EE9D055D20681192B09DB5CE58D61F, xmp.iid:1E896F146D20681192B09DB5CE58D61F, xmp.iid:FA7F117407206811B39FDAF3CEB6BEA9, xmp.iid:FB7F117407206811B39FDAF3CEB6BEA9, xmp.iid:FC7F117407206811B39FDAF3CEB6BEA9, xmp.iid:BE1E9B8F96206811B39FDAF3CEB6BEA9, xmp.iid:76C3FE4FCF206811B39FDAF3CEB6BEA9, xmp.iid:7CC3FE4FCF206811B39FDAF3CEB6BEA9, xmp.iid:7DC3FE4FCF206811B39FDAF3CEB6BEA9, xmp.iid:7EC3FE4FCF206811B39FDAF3CEB6BEA9, xmp.iid:50DD8B0752CCE111AFF8CAA5D822B0D2, xmp.iid:B8A8997F99D5E11193EF98F7734FE37A, xmp.iid:5688F2523BD7E111BC2BBFF9F645EB60, xmp.iid:B1586607F6D7E111B24AFCD161DF1BAB History When : 2011:08:31 10:32:55-05:00, 2011:08:31 10:37:53-05:00, 2011:08:31 10:37:54-05:00, 2011:09:14 15:27:07-05:00, 2011:09:14 16:08:37-05:00, 2011:09:28 18:00:22-05:00, 2011:09:30 17:35:23-05:00, 2011:10:02 11:14:07-05:00, 2011:10:02 11:14:07-05:00, 2011:10:03 09:19:07-05:00, 2011:10:03 09:43:25-05:00, 2011:10:03 10:55:33-05:00, 2011:10:03 11:44:38-05:00, 2011:10:04 17:46:07-05:00, 2011:10:06 14:12:22-05:00, 2011:10:06 15:09:56-05:00, 2011:10:07 13:37:19-05:00, 2011:10:07 14:31:40-05:00, 2011:10:07 14:35:10-05:00, 2011:10:07 14:35:10-05:00, 2011:10:09 10:33:17-05:00, 2011:10:09 14:59:03-05:00, 2011:10:09 18:09:24-05:00, 2011:10:09 19:46:11-05:00, 2011:10:09 22:28:27-05:00, 2011:10:09 22:29:15-05:00, 2011:10:09 22:56:40-05:00, 2011:10:09 23:45:19-05:00, 2011:10:10 07:49:35-05:00, 2011:10:10 13:23:17-05:00, 2011:10:10 15:04:44-05:00, 2011:10:11 15:17:57-05:00, 2011:10:11 15:37:31-05:00, 2011:10:13 10:22:34-05:00, 2011:10:17 15:35:08-05:00, 2011:10:17 16:23:04-05:00, 2011:10:19 15:57:15-05:00, 2011:10:21 16:15:53-05:00, 2011:10:21 17:09:29-05:00, 2011:10:21 17:10:54-05:00, 2011:10:26 12:21:35-05:00, 2011:10:26 13:50:31-05:00, 2011:10:26 15:02:51-05:00, 2011:10:26 16:07:12-05:00, 2011:10:27 14:02:53-05:00, 2011:10:27 14:02:53-05:00, 2011:10:27 14:54:13-05:00, 2011:10:27 17:00:17-05:00, 2011:10:28 15:59-05:00, 2011:10:31 10:50:06-05:00, 2011:10:31 11:40:20-05:00, 2011:11:01 09:21:52-05:00, 2011:11:01 09:23:39-05:00, 2011:11:01 09:24:17-05:00, 2011:11:01 09:24:17-05:00, 2012:01:26 15:25:17-06:00, 2012:01:26 15:25:17-06:00, 2012:01:31 17:09:15-06:00, 2012:01:31 17:09:16-06:00, 2012:01:31 17:21:20-06:00, 2012:01:31 17:21:20-06:00, 2012:01:31 17:23:17-06:00, 2012:01:31 17:25:14-06:00, 2012:01:31 17:25:14-06:00, 2012:02:22 15:39:08-05:00, 2012:02:22 15:40:02-05:00, 2012:02:22 15:41:42-05:00, 2012:02:22 15:44:53-05:00, 2012:02:22 15:46:35-05:00, 2012:02:22 15:59:05-05:00, 2012:02:27 11:43:28-05:00, 2012:02:27 11:44:42-05:00, 2012:02:27 11:45:06-05:00, 2012:02:28 19:57:33-05:00, 2012:02:28 19:59:28-05:00, 2012:02:28 23:32:17-05:00, 2012:02:28 23:32:35-05:00, 2012:02:28 23:32:35-05:00, 2012:07:12 16:04:15-05:00, 2012:07:24 10:00:57-05:00, 2012:07:26 16:53:14-05:00, 2012:07:27 09:19:08-05:00 History Software Agent : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0 History Changed : /, /metadata, /, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /;/metadata, /, /, /, /, /, /, /, /metadata, /, /metadata, /, /metadata, /;/metadata, /metadata, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /, /, / Derived From Instance ID : xmp.iid:7DC3FE4FCF206811B39FDAF3CEB6BEA9 Derived From Document ID : xmp.did:EE86E2D3624CE11192DAD1552C384A9B Derived From Original Document ID: xmp.did:F656357FE6D3E0118A2DE42CC6E34F51 Derived From Rendition Class : default Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:4b2a09ef-2f34-4098-afed-4ac63475dcf6, uuid:33ac4767-1bfa-406c-89ad-f9d9a68c76b6, uuid:33ac4767-1bfa-406c-89ad-f9d9a68c76b6, uuid:f064d6f3-1df8-4d5c-ab49-0f3dbc56bddc, uuid:f064d6f3-1df8-4d5c-ab49-0f3dbc56bddc, uuid:f064d6f3-1df8-4d5c-ab49-0f3dbc56bddc, uuid:9af02cd5-5baf-477e-be36-14df464f897c, uuid:7a779630-46b0-4351-94ce-e585a0df3249, uuid:a48f27e1-9813-40a3-9e8b-889928a6d662, uuid:8c66d66e-e543-494e-92ad-930578d17075, uuid:8c66d66e-e543-494e-92ad-930578d17075, uuid:cc5a01f1-8cbe-49bf-9e02-7ea685b52ff0, uuid:3f2a87aa-3a4d-458d-af9b-f32f40ceedc5, uuid:f03ec629-3fe7-46d9-bccf-9bafe9836229, uuid:91663ef1-954e-432c-930d-eb8e63007175, uuid:7a779630-46b0-4351-94ce-e585a0df3249, uuid:fcdadbe1-4856-4a81-bd4c-271521e0bf40, uuid:33ac4767-1bfa-406c-89ad-f9d9a68c76b6, uuid:b0dde184-c865-4be7-9a0f-d33a20b7604b, uuid:e8a36159-d46b-44c2-b9c5-6092ce9a8dcd, uuid:8c66d66e-e543-494e-92ad-930578d17075, uuid:a48f27e1-9813-40a3-9e8b-889928a6d662, uuid:3f2a87aa-3a4d-458d-af9b-f32f40ceedc5, uuid:3f2a87aa-3a4d-458d-af9b-f32f40ceedc5, uuid:c419c3ef-cc84-4f59-9b08-fd1e4780087b Manifest Reference Document ID : xmp.did:B708D79FDEEDE0118C57985F128AA49D, xmp.did:8A1F509854F3E011A4D0E62AD2D27899, xmp.did:8A1F509854F3E011A4D0E62AD2D27899, xmp.did:8B1F509854F3E011A4D0E62AD2D27899, xmp.did:8B1F509854F3E011A4D0E62AD2D27899, xmp.did:8B1F509854F3E011A4D0E62AD2D27899, xmp.did:75841E33F0F0E0118F8B9401D5B519C9, uuid:B6FE85AE5188DE11866DAD237D715C91, xmp.did:881F509854F3E011A4D0E62AD2D27899, xmp.did:891F509854F3E011A4D0E62AD2D27899, xmp.did:891F509854F3E011A4D0E62AD2D27899, xmp.did:220EE3C68501E1118333ABE6F1B483F8, xmp.did:8C1F509854F3E011A4D0E62AD2D27899, xmp.did:8D1F509854F3E011A4D0E62AD2D27899, xmp.did:8E1F509854F3E011A4D0E62AD2D27899, uuid:B6FE85AE5188DE11866DAD237D715C91, uuid:B4FE85AE5188DE11866DAD237D715C91, xmp.did:8A1F509854F3E011A4D0E62AD2D27899, xmp.did:8F1F509854F3E011A4D0E62AD2D27899, xmp.did:901F509854F3E011A4D0E62AD2D27899, xmp.did:891F509854F3E011A4D0E62AD2D27899, xmp.did:881F509854F3E011A4D0E62AD2D27899, xmp.did:8C1F509854F3E011A4D0E62AD2D27899, xmp.did:8C1F509854F3E011A4D0E62AD2D27899, uuid:68355382CD95DF119B7BD5FAD30EB85F Doc Change Count : 33797 Format : application/pdf Producer : Adobe PDF Library 9.0 Trapped : False Page Count : 76 Creator : Adobe InDesign CS4 (6.0)EXIF Metadata provided by EXIF.tools