Uniform 680 Contactless Card Reader User Manual

Uniform Industrial Corp. Contactless Card Reader

User Manual

UIC680 Simple Manual 2008-10-20 PM076-S Revision 1 Page 1 of 2 UIC680 SERIES Contactless Smart Card Reader Module - RS232 & USB HID Keyboard Interface - (Support M-Chip & qVSDC) Thank you for purchasing the UIC680 series products. The contactless smart card reader module UIC680 is mainly to support the contactless payment systems. The small footprint size of the module makes it easily to integrate to the current transaction system such as Point-of-Sale terminal, kiosk, and vending machine station as the part of the system. The module communicates with a host computer or terminal using a standard RS-232, USB or TTL interface. FEATURES z Small footprint PCB size: 50 L* 40 W (mm) without antenna board z Supports ISO 14443 type A & B standard z Supports American Express® ExpressPay, MasterCard® PayPassTM, Visa® MSD applications z Reads/writes Philips Mifare® classical contactless smart card z Provides the options for the direct coupling antenna and the remote antenna z RS232, USB 2.0 and serial TTL (optional) Interface z RS232 data pass through function z TTL F2F magnetic stripe decode data pass through (optional) z F2F decoder data emulation (optional) z Firmware upgradeable AGENCY APPROVAL z Specifications for FCC Class B, CE Class B NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void your authority to operate such equipment. SPECIFICATIONS Communication Standard RS232 signal level Compatible with USB 2.0 specification (optional)/TTL 5V signal level (optional) Power Requirements 5VDC Power Consumption 330mA in idle mode; 430mA in operating mode Operating Temperature -10 to 50℃ Operating Humidity 10 to 85% (non condensing) Dimensions 50L x 40W mm, without antenna board Pb
UIC680 Simple Manual 2008-10-20 PM076-S Revision 1 Page 2 of 2 PIN ASSIGNMENT Interface J3 Pin Assignment DB9 Signal Direction PCB-J1 Signal 5 GND 1 GND 2 RxD Å Serial data to host 2 TXD1 3 TxD Æ Serial data from host 3 RXD1 4 VCC Serial Pass-thru or USB data 5 TXD2 (or USB D-) Serial Pass-thru or USB data 6 RxD2 (or USB D+) Shield 7 Shield Extension Port J1 Pin Assignment Pin Signal Comment 1 GND 2 GND 3 Extended IO 4 Extended IO 5 GND 6 VCC 5Vdc 7 Extended IO 8 Extended IO 9 Extended IO 10 Extended IO 11 Extended IO 12 Extended IO 13 Extended IO 14 Extended IO 15 Extended IO 16 Extended IO 17 Extended IO 18 Extended IO 19 GND 20 VCC_33 3.3V 21 Extended IO 22 Extended IO 23 Extended IO 24 Buzzer Control Signal 25 Extended IO 26 Extended IO 27 Extended IO 28 Extended IO 50 RF Antenna Port J2B Pin Assignment Contact number Signal 1 RF output 2 GND Direct Match Antenna Port J2A Pin Assignment Contact number Signal 1 RX 2 TX 3 GND 4 GND

Navigation menu