Uniform UIC682 Contactless Smart Card Reader Module User Manual UIC680 Programmer s Manual

Uniform Industrial Corp. Contactless Smart Card Reader Module UIC680 Programmer s Manual

Users Manual

UIC682 Contactless Smart Card Reader Module -RS232/TTL Interface- Programmer’s Manual Revision 1 July. 5, 2007
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 NOTICE The issuer of this manual has made every effort to provide accurate information contained in this manual. The issuer shall not be held liable for any technical and editorial omissions or errors made herein; nor for incidental consequential damages resulting from the furnishing, performance or use of this material. This document contains proprietary information protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated without the prior written permission of the issuer. The information provided in this manual is subject to change without notice. AGENCY APPROVED - Specification for FCC Class B - Specification for CE Class B, CISPR 22 Class B NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void your authority to operate such equipment. WARNING You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. WARRANTY This product is served under one-year warranty of defects in material and functionality to the original purchasers. Within the warranty period, if the product found to be defective will be repaired or replaced. This warranty applies to the products only under the normal use of the original purchasers, and in no circumstances covers incidental or consequential damages through consumers’ misuse or modification of the product. PREFACE I
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 This manual provides detailed information relating to the overall operational, electrical, mechanical, environmental and functional aspects of the UIC682. This document should be read and understood prior to initial operation of the product. For ease of installation and programming use, we have addressed everything from its attractive features to its various configurations. When designing the UIC682, we selected what we feel are the most useful features and functions. If in some cases you find that your specific needs differ from our existing products, we welcome your comments and suggestions. Custom-designed models are also available. If further questions do arise, please call for technical support, our FAE will assist you in any way we can. II
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 Table of Contents Section1 : General Description................................................................. 1-1 1.1 Features............................................................................................................. 1-1 1.2 Application ........................................................................................................ 1-1 1.3 Part Number Description ................................................................................. 1-2 Section2 : Configurations ......................................................................... 2-1 2.1 Dimensions of UIC682 PCBA........................................................................... 2-1 2.2 Dimensions of Remote Antenna PCBA........................................................... 2-1 2.3 Accessories of UIC682 ..................................................................................... 2-1 Section3 : Technical Specifications ......................................................... 3-1 3.1 Functional Specifications ................................................................................ 3-1 3.2 Mechanical Specifications............................................................................... 3-1 　 Dimension............................................................................................................................. 3-1 3.3 Electrical Specifications................................................................................... 3-2 　 Power Required.................................................................................................................... 3-2 　 Power Consumption ............................................................................................................. 3-2 　 Communication..................................................................................................................... 3-2 　 Communication Signal (RS232) ........................................................................................... 3-2 3.4 Environmental Specifications.......................................................................... 3-2 　 Temperature.......................................................................................................................... 3-2 　 Humidity................................................................................................................................3-2 3.5 Pin Assignment................................................................................................. 3-3 3.6 Communication................................................................................................. 3-4 　 RS232 Interface Data Output ............................................................................................... 3-4 　 RS232 Interface Pass Through ............................................................................................ 3-4 　 F2F TTL Interface (Optional) ................................................................................................ 3-4 　 Transmission Protocol.......................................................................................................... 3-4 　 Self – Arm Mode ................................................................................................................... 3-5 　 Transmission Format............................................................................................................ 3-5 Section4 : Commands and Responses.................................................... 4-1 4.1 Reader Default Setting ..................................................................................... 4-1 4.2 Reader Command Description ........................................................................ 4-2 　 % (25H) – Retransmit........................................................................................................... 4-2 　 70 (3730H) or 90 (3930H) – Serial Number Report ............................................................. 4-2 　 71 (3731H) or 91 (3931H) – Copyright Report..................................................................... 4-2 　 72 (3732H) or 92 (3932H) – Reader Model Number Report................................................ 4-2 III
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 　 73 (3733H) or 93 (3933H) – Reader PCB Number Report .................................................. 4-2 　 77 (3737H) or 97 (3937H) – Reader Configuration Data Report ......................................... 4-2 　 78 (3738H) or 98 (3938H) – Reader Customer Configuration Data Report......................... 4-3 　 79 (3739H) or 99 (3939H) – Reader Manufacturing Configuration Data Report ................. 4-3 　 9 (39H) – Version Report...................................................................................................... 4-4 　 ? (3FH) – Select Verbose Responses Command ................................................................ 4-4 　 $ (24H) – Reader Status Request ........................................................................................ 4-4 　 L (4CH) – LED ON................................................................................................................ 4-4 　 l (6CH) – LED OFF............................................................................................................... 4-5 　 ( (28H) – LED Flash.............................................................................................................. 4-5 　 # (23H) – Configuration Request.......................................................................................... 4-5 　 <DC2> (12H) – RS232 pass through enable ....................................................................... 4-5 　 <CAN> (18H) – Clear Data Buffer........................................................................................ 4-6 　 <7FH> – Warm Reset........................................................................................................... 4-6 　 <09H> – Configuration Setting ............................................................................................. 4-6 　 P (50H) – Arm to Read ......................................................................................................... 4-6 　 p (70H) – Arm to Read (Used for Manufacturing Test Only)................................................. 4-6 　 <ESC> (1BH) – Abort Arm to Read ...................................................................................... 4-7 　 Q (51H) – Transmit Track 1 data .......................................................................................... 4-7 　 R (52H) – Transmit Track 2 data .......................................................................................... 4-7 　 S (53H) – Transmit Track 3 data........................................................................................... 4-7 　 H (48H) – Self-ARM function disable/enable........................................................................ 4-7 4.3 Contactless Card Operation Command Description ..................................... 4-9 　 G (47H) – ISO14443 type protocol select ............................................................................ 4-9 　 O (4FH) – Antenna power ON .............................................................................................. 4-9 　 o (6FH) – Antenna power OFF ............................................................................................. 4-9 　 b (62H) – Request ................................................................................................................ 4-9 　 c (63H) – Anticollision(type A)/Slot-Marker(type B) ............................................................ 4-10 　 f (66H) – Select(type A)/Attrib(type B) ................................................................................ 4-10 　 g (67H) – Mifare classical card authentication (Support Mifare classical card only).......... 4-11 　 h (68H) – Mifare classical card read block (Support Mifare classical card only)................ 4-11 　 i (69H) – Mifare classical card write block (Support Mifare classical card only) ................ 4-12 　 t (74H) – Mifare Value Operation (Support Mifare classical card only) .............................. 4-12 　 X (58H) – Mifare classical card activation .......................................................................... 4-13 　 x (78H) – Card halt ............................................................................................................. 4-13 　 J (4AH) – Activate PICC cpu card ...................................................................................... 4-13 　 j (6AH) – Load Mifare key (Support Mifare classical card only) ......................................... 4-14 　 y (79H) – Send DESELECT command............................................................................... 4-14 　 Z (5AH) – I/O to contactless CPU card with APDU format................................................. 4-14 　 z (7AH) – I/O to contactless card for block data exchange ................................................ 4-15 IV
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 4.4 Responses to the Host....................................................................................4-16 Section5 : Application Example................................................................ 5-1 V
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 Section1: General Description This section presents general information about the basic characters of the UIC682. 1.1 Features The UIC682 provides the following features: 1 Small footprint PCB size: 87 L* 20 W (mm) without antenna board 2 Support ISO 14443 type A & B standard 3 Support American Express® ExpressPay, MasterCard® PayPassTM, Visa® MSD applications. 4 Read/write Philips Mifare® classical contactless smart card 5 RS232, and serial TTL (optional) Interface 6 RS232 data pass through function 7 TTL F2F magnetic stripe decode data pass through 8 F2F decoder data emulation (optional) 9 Firmware upgradeable 1.2 Application The contactless smart card reader module UIC682 is mainly to support the contactless payment systems. The small footprint size of the module makes it easily to integrate to the current transaction system such as Point-of-Sale terminal, kiosk, and vending machine station as the part of the system. The module communicates with a host computer or terminal using a standard RS-232 or TTL interface. At the meantime, UIC682 offers both RS232 and TTL magnetic stripe decoder pass-thru function to allow the terminal to share the same input port with other peripheral devices. The TTL interface output is in the F2F decoder data emulation. This benefits the existing system without change its hardware configuration to catch up the future payment trend. 1-1
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 1.3 Part Number Description 1-2
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 Section2: Configurations This section shows the dimensions and accessories of the UIC682. 2.1 Dimensions of UIC682 PCBA Figure 2-1 Dimensions of UIC682 2.2 Dimensions of Remote Antenna PCBA Figure 2-2 Dimensions of Remote Antenna PCBA 2.3 Accessories of UIC682 The following accessories should be supplied along with UIC682. Make sure all the following accessories are contained in your package. 1. Interface cable - DB9 male connector 1.5M 2. Power adapter 5VDC 500mA (RS232 interface only) 2-1
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 Section3: Technical Specifications 3.1 Functional Specifications • Contactless communication at 13.56MHz • Proximity operation distance of up to 100mm • LED indication (support PayPass application) • Audio buzzer • Support RS232 data output baud rate up to 115.2K BPS • Support RS232 pass through baud rate up to 38400 BPS • Support TTL level for serial data output (optional) • Support TTL level for F2F decoder data output emulation (optional) • Support Remote 50 ohm matching antenna • Support all layers of 14443 including the type A and B communication scheme • Support contactless communication using MIFARE higher baud rate up to 424KHz • Support the MIFARE Classic products • Support American Express ExpressPay transaction application • Support MasterCard PayPass transaction application • Support Visa MSD transaction application 3.2 Mechanical Specifications • Dimension Without antenna board Length: 87 mm Width: 20 mm 3-1
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 3.3 Electrical Specifications • Power Required 5VDC • Power Consumption 350mA in operating mode • Communication Standard RS232 signal level TTL 5V signal level (optional) • Communication Signal (RS232) Logic 1 = -3 volts to –15 volts or TTL level 5 volts Logic 0 = +3 volts to +15 volts or TTL level 0 volt 3.4 Environmental Specifications • Temperature Operating: -10 ~ 50℃ Storage: -30 ~ 70℃ • Humidity Operating: 10 ~ 85% (non condensing) Storage: 10 ~ 90% (non condensing) 3-2
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 3.5 Pin Assignment Table 3-1. Interface J3 Pin Assignment DB9 Signal Direction PCB-J1 Signal 5 GND 1 GND 2 RxD Å Serial data to host 2 TXD1 3 TxD Æ Serial data from host 3 RXD1 4 VCC Serial Pass-thru 5 TXD2 Serial Pass-thru 6 RxD2 Shield 7 Shield Table 3-2. Extension Port J1 Pin Assignment Pin Signal Comment 1 Extended IO 2 Extended IO 3 Extended IO 4 Extended IO 5 GND 6 VCC 5Vdc 7 Extended IO 8 Extended IO 9 Extended IO 10 Extended IO 11 Buzzer + output 12 Buzzer – output 13 Extended IO 14 Extended IO 15 Extended IO 16 Extended IO 17 Extended IO 18 Extended IO 19 Extended IO 20 Extended IO 21 Extended IO 22 Extended IO 23 Extended IO 24 Extended IO Table 3-3. 50 RF Antenna Port J2B Pin Assignment Contact number Signal 1 RF output 2 GND Table 3-4. Direct Match Antenna Port J2A Pin Assignment Contact number Signal 1 RX 2 TX 3 GND 4 GND 3-3
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 3.6 Communication • RS232 Interface Data Output Synchronization The interface receives and transmits serial asynchronous data at voltage levels compatible with the RS232 specification. Baud Rate 9600 BPS default (optional: 1200/2400/4800/9600/19200/38400/56000/115.2K BPS) • RS232 Interface Pass Through Baud Rate 9600 BPS default (optional: 1200/2400/4800/9600/19200/38400 BPS) • F2F TTL Interface (Optional) Each track has the clock and data. Please refer to command set for the detail setting. • Transmission Protocol The user may select from three different protocols: Protocol 0, 1, and 2. Upon reset, the reader sends the power-on response “:”, depending upon the configuration setting. The reader then configures itself to the protocol of the first command from the host. From this point on, the protocol is unchangeable until a reset occurs. Protocol 0 In Protocol 0, all characters are transmitted and received using exactly the characters listed in section 4. There are no headers and Block Check Characters (BCC). Protocol 0 presumes no transmission errors. If the host detects an error, it may request a retransmission. Table 3-5. Example for Protocol 0 Protocol 1 In Protocol 1, all messages are preceded by the ASCII character <STX> and terminated with the ASCII character <ETX>, followed by a one byte <BCC>. <BCC> is an XOR of the 7 data bits, excluding parity, of each character in the entire message, including <STX>. Format: <STX><MESSAGE><ETX><BCC> where STX=02Hex and ETX=03Hex. Table 3-6. Example for Protocol 1 Host Command Reader Response Comment P Ready to read ^ Reader ACK Host Command Reader Response Comment 02h 50h 03h 51h Ready to read 02h 5Eh 03h 5Fh Reader ACK 3-4
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 Protocol 2 In Protocol 2, all messages are preceded by the ASCII character <SOH>, followed by a one byte reader address, two bytes character count and terminated with a one byte <BCC>. The <BCC> is an XOR of the characters (8 bits) in the entire message, including <SOH>. Format: <SOH><ADDRESS><00Hex><COUNT><MESSAGE><BCC> Table 3-7. Example for Protocol 2 The <ADDRESS> field is for a multi-reader system. This function is not currently supported. The recommended value for this field is NULL (00Hex), however, any value will work. For Protocols 1 and 2, if the reader detects an error in an incoming transmission, it will respond with a “Communications Error” message. If the host detects a transmission error, it may request a retransmission. Besides, all protocols enforce a 10mSec timeout between characters. • Self – Arm Mode The default reader configuration is the “Self-Arm Mode”, which allows the payment cards (Including PayPass Magnetic Stripe, VISA MSD, ExpressPay card and the general magnetic stripe credit cards) reading functions to run automatically, reporting the card data to the host without instruction from the host. In the Self-Arm Mode, the reader also can accept commands from host. However, the reader can be configured to only “Host Polled Mode” by disabling Self-Arm Mode. The “Host Polled Mode” allows the card reading functions to run by commands. • Transmission Format In Self-ARM mode, the default setting of card data output doesn’t include the protocol envelope code. The user can turn on the envelope code by utilized the configuration command – SE, TO. (Please refer to the appendix section of UIC682 Configuration Guide) Card output format (Self-ARM mode) Preamble Protocol Envelope code Tk1 prefix Tk1 Data Tk1 suffix Separator Tk2 prefix Tk2 Data Tk2 suffix Host Command Reader Response Comment 01h 00h 00h 01h 50h 50h Ready to read 01h 00h 00h 01h 5Eh 5Eh Reader ACK 3-5
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 Separator Tk3 prefix Tk3 Data Tk3 suffix Protocol Envelope code Postamble The preamble/postamble is only available in the card data output format under Self-ARM mode. Read data for command (Host-Polled mode) The reader replies the host command such as “Transmit Track Data” so called “Host-Polled”. The requested message is encapsulated in the protocol envelope. The response of Transmit Track Data command list as below: Read tk1 data for command Protocol Envelope code Tk1 prefix Tk1 Data Tk1 suffix Protocol Envelope code Read tk2 data for command Protocol Envelope code Tk2 prefix Tk2 Data Tk2 suffix Protocol Envelope code Read tk3 data for command Protocol Envelope code Tk3 prefix Tk3 Data Tk3 suffix Protocol Envelope code NOTE1: Tkx data: SS (option) track data ES (option) LRC (option) NOTE2: Preamble/Postamble, prefix/suffix are optional based on reader’s configuration. NOTE3: Protocol Envelope code can be <HEADERS>, <BCC> or NONE depended on what protocol is in used. 3-6
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 Section4: Commands and Responses 4.1 Reader Default Setting Item Description EEPROM Default Value Interface type RS232 UART1 setting (Txd1/Rxd1) 9600-8-N-1 Data pass through mode Disable UART2 setting (Txd1/Rxd2) 9600-8-N-1 Buzzer Enable Protocol format USI0 Contactless Self-ARM mode Enable Contactless smart card manual type Type A NOTE1: When “Contactless self-arm mode” turns on, UIC682 will automatic read the payment card1 in the reading zone for both type A and B cards. NOTE2: The contactless card operation commands are invalid when “Self-ARM mode” is enabled. To switch manual operation mode, user needs to disable the “Self-ARM mode” first. 1 Payment card – the card with PayPass, ExpressPay, or MSD application. 4-1
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 4.2 Reader Command Description • % (25H) – Retransmit COMMENT Retransmits the last message sent by the reader. NOTE Command is turned off in self-arm mode. • 70 (3730H) or 90 (3930H) – Serial Number Report COMMENT Transmit serial number information. The serial number will be stored in the EEPROM and stored as an eight-digit ASCII character array. Example: “00000000” • 71 (3731H) or 91 (3931H) – Copyright Report COMMENT Transmit version and copyright information. Send this when you want to know the version and copyright of the Model UIC682 firmware currently loaded. The response is an ASCII string giving the firmware date (yymmdd), reader type and the firmware version number followed by the firmware copyright statement. The firmware copyright statement is absent in OEM version. Example: “60706,UIC 6800104C:V4.C” • 72 (3732H) or 92 (3932H) – Reader Model Number Report COMMENT Transmit reader model information. The model number will be stored in the reader code area. Example: “UIC682-RR” • 73 (3733H) or 93 (3933H) – Reader PCB Number Report COMMENT Transmit reader PCB number. The PCB number will be stored in the EEPROM and stored as an eight-digit ASCII character array. Example: “680-REV1” • 77 (3737H) or 97 (3937H) – Reader Configuration Data Report 4-2
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 COMMENT Transmit the reader configuration data. The data from the reader configuration area will be transmitted to the host as hex values with the command “77” [offset] [num]. The reader will return any or all the bytes from the reader configuration. The offset is an optional byte and the available value is from 0x00 to 0x3F. The num is an optional byte specifying the number of configuration bytes to be returned. If the offset and length bytes are omitted then the current configuration starting at offset 0 is transmitted. Example: BE 4C 03 03 00 00 00 61 30 35 30 35 30 36 82 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3A 36 38 30 2D 52 48 00 • 78 (3738H) or 98 (3938H) – Reader Customer Configuration Data Report COMMENT Transmit the reader customer configuration data. The data from the reader customer configuration area of the EEPROM will be transmitted to the host as hex values with the command “78¨ [offset] [num]. The reader will return any or all the bytes from the reader configuration. The offset is an optional byte and the available value is from 0x00 to 0x3F. The num is an optional byte specifying the number of configuration bytes to be returned. If the offset and length bytes are omitted then the current configuration starting at offset 0 is transmitted. Example: 00 30 30 30 30 30 30 30 30 36 38 30 2D 52 45 56 31 03 04 03 02 00 3C 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 45 00 2B FF FF FF FF FF FF FF FF FF FF FF FF 3F 3F 12 FF 06 3F 05 13 50 03 • 79 (3739H) or 99 (3939H) – Reader Manufacturing Configuration Data Report COMMENT Transmit the reader manufacturing configuration data. The data from the reader manufacturing configuration area of the flash will be transmitted to the host as hex values with the command “79” [offset] [num]. The reader will return any or all the bytes from the reader configuration. The offset is an optional byte and the available value is from 0x00 to 0x7F. The num is an optional byte 4-3
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 specifying the number of configuration bytes to be returned to the host. If the offset and length bytes are omitted then the current configuration starting at offset 0 is transmitted. Example: BE 4C 03 03 00 00 00 61 30 35 30 35 30 36 82 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3A 36 38 30 2D 52 48 00 • 9 (39H) – Version Report COMMENT Transmit version information. Send this when you want to know the version of UIC682 firmware currently loaded. The response is an ASCII string giving the firmware date (mmddyy), reader type and firmware version number. Example: “060706,UIC682-RR:V4.C¨. • ? (3FH) – Select Verbose Responses Command COMMENT Most error responses until the reader receives a reset command will include a short descriptive message. • $ (24H) – Reader Status Request COMMENT Interrogate the reader about its operational status. Two bytes of status information will be returned. First Status Byte Bit Value: 0 Value: 1 0 – 4 Reserve for future use Reserve for future use 5 No Magnetic Stripe Card data Magnetic Stripe Card data 6 Not armed to read Armed to read 7 Reserve for future use Reserve for future use Second Status Byte (reserve for future use) • L (4CH) – LED ON 4-4
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 • l (6CH) – LED OFF • ( (28H) – LED Flash COMMENT 1.Turn first/second LED ON/OFF/Flash, as specified. 2.Transmits an acknowledgement "^" (5EH). NOTE 1.These commands are disabled in the self-arm mode. 2.These commands only use in LED model. • # (23H) – Configuration Request COMMENT Return standard one byte or extended 16-byte string with configuration. NOTE Using the configuration setting command to select standard or extended format. Standard One Configuration Byte Bit Value: 0 Value: 1 0 Track 1 not present Track 1 present 1 Track 2 not present Track 2 present 2 Track 3 not present Track 3 present 3-7 Reserved for future use Reserved for future use Extended Configuration Bytes (16 bytes) Byte 0 1 2 3 4 5-15 Remark Equip.0 Equip.1 Protocol Speed Address ReservedProtocol: 0=USI0; 1=USI1; 2=USI2. Speed: 0=1200, 1=2400, 2=4800, 3=9600, 4=19.2k, 5=38.4k, 6=56k, and 7=115.2k bps. Address: Always 00H. Equip. 0 － Extended Configuration Byte 0 Bit Value: 0 Value: 1 0-3 Reserved for future use Reserved for future use 4 Track 1 not present Track 1 present 5 Track 2 not present Track 2 present 6 Track 3 not present Track 3 present 7 Reserved for future use. Reserved for future use Equip. 1 － Extended Configuration Byte 1 Bit Value: 0 Value: 1 0 - 7 Reserved for future use Reserved for future use • <DC2> (12H) – RS232 pass through enable 4-5
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 COMMENT Enable RS232 data Pass Through (PT) function temporarily. FORMAT The command characters are followed by an ASCII ‘P’ to enable the RS232 pass through function. It is only valid in RS232 model. NOTE Once the pass through mode is enabled, UIC682 passes all data between COM1 and COM2 and do nothing. Power cycling (if the default of PT is disable) or send the string “<DC2>P<DC2>a<DC2>s<DC2>S” brings UIC682 back to normal operation. Before sending this command, the user must assure the PT function is desired. • <CAN> (18H) – Clear Data Buffer COMMENT Clear the card data buffer. • <7FH> – Warm Reset COMMENT Abort all current actions and cause the device to execute all initialization functions. The device will respond as it would for a "power up" cycle, but always returning a “:” (3AH). This operation will take at least 3 seconds. • <09H> – Configuration Setting COMMENT This command is used to set configuration in EEPROM. FORMAT The command (09H) is followed by the configuration data format to set the configuration in EEPROM. Please see “UIC682 Configuration Guide” for more details. • P (50H) – Arm to Read COMMENT 1.Clear read data buffers. 2.Transmit command acknowledgement (“^” 5EH). 3.Wait for card approached. 4.Transmit read acknowledgement ("^") after card read. After an "Arm to Read" command is received and acknowledged the only commands that will be accepted for execution are: <ESC> (Abort), ”$” (Status), LED control commands and Reset command. In self-arm mode, it is not necessary to send this command, if sent it will temporarily override self-arm mode. • p (70H) – Arm to Read (Used for Manufacturing Test Only) 4-6
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 COMMENT 1.Clear read data buffers. 2.Transmit command acknowledgement (“^” 5EH). 3.Wait for card read. 4.If the card media is detected a "(" (28H) byte is sent, when media detect goes inactive a “)” (29H) byte is sent. This is similar to the 'P' command but send ‘(‘ at start of magnetic stripe card data and ‘)’ at end. • <ESC> (1BH) – Abort Arm to Read COMMENT 1.Clear read data buffers. 2.Abort Arm to Read Command. 3.Transmit command acknowledge (“^” 5EH). • Q (51H) – Transmit Track 1 data • R (52H) – Transmit Track 2 data • S (53H) – Transmit Track 3 data COMMENT 1.Detect the card type automatically and process data in the read buffer.2.If error is detected, transmit proper error response ('*' or '+'), refer to “Responses to the Host” section. 3.Else, transmit data in ASCII. • H (48H) – Self-ARM function disable/enable COMMENT Disable auto read function temporarily if Self-Arm is enabling. H [Enable/Disable, 1 byte] [Enable/Disable] 0 (30h, ASCII Hex) - Self-Arm disable 1 (31h, ASCII Hex) - Self-Arm enable NOTE UIC682 cannot perform the Self-ARM enable command for the contactless payment card reading under below conditions: 1.The payment card is decoded successful and the UIC682 is waiting the card to be removed from the reading zone. 2.The payment card is failed to decode and the UIC682 is waiting the card to be removed from the reading zone. RESPONSE ‘^’ – Acknowledgement 4-7
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 ‘*’ – Cannot execute ‘!’ – Bad parameter 4-8
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 4.3 Contactless Card Operation Command Description • G (47H) – ISO14443 type protocol select COMMENT Select ISO 14443 type A or B which manual command operated. G[Type, 1 byte] [Type] 0 (30h, ASCII Hex) - ISO14443 A 4 (30h, ASCII Hex) - ISO14443 B The default contactless smart card type is type A after power up. RESPONSE ‘^’ – Acknowledgement ‘!’ – Bad parameter • O (4FH) – Antenna power ON COMMENT Apply power on the antenna. This command is for manual command operation. RESPONSE ‘^’ – Acknowledgement ‘*’ – Failed, the reader is in Self-Arm mode. The antenna power cannot be turned off. • o (6FH) – Antenna power OFF COMMENT Turn the antenna power off. RESPONSE ‘^’ – Acknowledgement ‘*’ – Failed, the reader is in Self-Arm mode. The antenna power cannot be turned off. • b (62H) – Request COMMENT Request command. b[Req command, 1 byte] - If reader is set to ISO14443 type A [Req command] (optional) The request command code is ISO14443 type A. It can be either 26 (REQA) or 52 4-9
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 (WUPA) NOTE If the [Req command] field does not appear in the request command, reader will set the request mode to WUPA automatically. b[AFI, 1 byte][Parameter, 1 byte] - If reader is set to ISO14443 type B [AFI](optional) - Binary hex (00h to FFh), please refer to ISO 14443-3 for the detailed information [Parameter](optional) - Binary hex (00h to FFh), please refer to 14443 for the detailed information. NOTE If the [AFI] and [Parameter] do not appear in the request command, reader will set the request mode to WUPB automatically. RESPONSE ATQA (2 bytes, type A, Binary Hex) or ATQB (16 bytes, type B, Binary Hex) if command executed successfully ‘*’ – No card response or No power on the antenna • c (63H) – Anticollision(type A)/Slot-Marker(type B) COMMENT In type A mode, the reader sends the Anti-collision command to the card. In type B mode, the reader sends the Slot-Marker command to the card. c – ISO 14443 type A c[APn] – ISO14443 type B [APn] – Anti-collision prefix byte.(type B only) NOTE Slot-Marker is not a mandatory command for type B card. RESPONSE If the command executed successfully, the reader returns PICC serial number for type A (Binary Hex) or PICC send ATQB (12 bytes, Binary Hex) for type B ‘*’ – No card response or or No power on the antenna ‘!’ – Bad parameter • f (66H) – Select(type A)/Attrib(type B) COMMENT In type A mode, the reader sends the SELECT command to the card. In type B mode, the reader sends the ATTRIB command to the card. RESPONSE If the command executed successfully, the reader returns 4-10
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 ‘^’ + SAK( 1 byte) or ‘^’ + MBLI/CID(1 byte) ‘*’ – No card response or No power on the antenna • g (67H) – Mifare classical card authentication (Support Mifare classical card only) COMMENT Mifare classical card authentication. g[Block number, 3 bytes][Key number, 1 byte][Key type] Authenticate the card with the key stored in EEPROM. or g[Block number, 3 bytes] ][Key type] [Key, 12 bytes] Authenticate the card with the key in [key field]. [Block number] There are two types of block format 000 to 255 (30h30h30h to 32h35h35h, ASCII Hex) or B<00><00> to B<00><FF> (42h00h00h to 42h00hFFh, ASCII Hex) [Key number] 0 to 4 (30h to 35h, ASCII Hex) [Key] 0 to 9 or A to F (30h - 39h or 41h - 46h, ASCII Hex) [Key type] A or B (41h or 42h) RESPONSE ‘^’ – acknowledgement ‘*’ – No card response or No power on the antenna • h (68H) – Mifare classical card read block (Support Mifare classical card only) COMMENT Mifare classical card read command. h[Block number, 3 bytes] [Block number] 4-11
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 There are two types of block format 000 to 255 (30h30h30h to 32h35h35h, ASCII Hex) or B<00><00> to B<00><FF> (42h00h00h to 42h00hFFh, ASCII Hex) RESPONSE block data (16 bytes, Binary Hex) if command executed successfully ‘*’ – No card response or No power on the antenna • i (69H) – Mifare classical card write block (Support Mifare classical card only) COMMENT Mifare classical card write command. i[Block number, 3 bytes][Block data, 4 bytes or 16 bytes] [Block number] There are three types of block number format 000 to 255 (30h30h30h to 32h35h35h, ASCII Hex) General Mifare Block or B<00><00> to B<00><FF> (42h00h00h to 42h00hFFh, ASCII Hex) General Mifare Block or U<00><00> to B<00><FF> (55h00h00h to 42h00hFFh, ASCII Hex) Mifare Ultralight [Block data] For Mifare Ultralight, the block data should be 4 bytes, others are using 16 bytes block data. RESPONSE ‘^’ – Acknowledgement ‘*’ – No card response or No power on the antenna • t (74H) – Mifare Value Operation (Support Mifare classical card only) COMMENT Mifare classical card value operation command. t[Block number, 3 bytes][Operation mode, 1 byte][Value, 4 bytes][transfer block, 3 bytes] [Block number] 4-12
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 There are two types of block number format 000 to 255 (30h30h30h to 32h35h35h, ASCII Hex) or B<00><00> to B<00><FF> (42h00h00h to 42h00hFFh, ASCII Hex) [Operation mode] 0 (30h, ASCII Hex) – Decrement 1 (31h, ASCII Hex) – Increment 2 (32h, ASCII Hex) – Restore 3 (33h, ASCII Hex) – Decrement and transfer to the different block. 4 (34h, ASCII Hex) – Create Mifare Value in the block. [Value] Binary Hex from 0h to FFh For option 3 only, the data format is same as [block number] RESPONSE ‘^’ – Acknowledgement ‘*’ – No card response or No power on the antenna ‘!’ – Bad parameter • X (58H) – Mifare classical card activation COMMENT Perform request/anticollision/select command to activate the card. It is also can be used for any ISO14443 compatible card. RESPONSE ATQA/SAK/serial number if the command executed successfully for type A card ATQB (12 bytes) if the command executed successfully for type B card ‘*’ – No card response or No power on the antenna • x (78H) – Card halt COMMENT Card halt command. RESPONSE ‘^’ – acknowledgement ‘*’ – No card response or No power on the antenna • J (4AH) – Activate PICC cpu card 4-13
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 COMMENT Activate PICC cpu card command. The Antenna POWER ON command has to be sent first. RESPONSE ATS (type A) or PUPI (type B) if command executed successfully ‘*’ – No card response or No power on the antenna • j (6AH) – Load Mifare key (Support Mifare classical card only) COMMENT Save up to 5 key sets for Mifare classical card application NOTE For security reason, there is no way to retrieve the key back. j[Key number, 1 byte][Key data, 12 bytes] [Key number] 0 to 4 (30h to 39h, ASCII Hex) [Key data] 0 to 9 or A to F (30h - 39h or 41h - 46h, ASCII Hex) RESPONSE ‘^’ – acknowledgement ‘*’ – No card response or No power on the antenna • y (79H) – Send DESELECT command COMMENT Send ISO14443 layer 4 DESELECT command to card RESPONSE ‘^’ – acknowledgement ‘*’ – No card response or No power on the antenna • Z (5AH) – I/O to contactless CPU card with APDU format COMMENT The command is used to pass an APDU to the card where both data and an ISO status are expected in the response. Z[APDU, variant, 262 bytes max] [APDU] Binary hex (00h to FFh) If successful, the data from the ICC and the two byte SW1/SW2 ISO 7816-4 response are returned. If unsuccessful, reader transmits '*'. 4-14
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 APDU Command Structure CLA INS P1 P2 P3 Lc or Le Data (If Lc present) APDU Response Structure Data (optional) SW1 SW2 • z (7AH) – I/O to contactless card for block data exchange COMMENT The command is used to pass a block data to a card. z[CRC mode, 1 bytes][Wait time, 4 bytes][Block data, 384 bytes max.] [CRC mode] 0 (30h, ASCII Hex) – Block data contain 2 bytes CRC and enable CRC transmission. 1 (31h, ASCII Hex) – No CRC in block data and disable CRC transmission. [Wait time] 0000 to 9999 (30h30h30h30h to 39h39h39h39h, ASCII Hex) Waiting time in ms. [Block data] Binary hex (00h to FFh), Maximum accepts 384 bytes. If successful, the data from the ICC are returned. If unsuccessful, reader transmits '*'. 4-15
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 4.4 Responses to the Host ^ (5EH) Acknowledge. Acknowledges correct completion of most recent command. * (2AH) Command was received correctly. But could not be completed. + (2BH) No Magnetic Stripe Card Data. Command was received correctly. ? (3FH) Communication Error. Command was not received correctly. ! (21H) Invalid Command or bad parameter. : (3AH) Power On report. ~ (7Eh) Unavailable. Hardware not available to complete this request. 4-16
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 Section5: Application Example The default setting of UIC682 reader, Self-ARM mode, is mainly to simplify the process for the host that doesn’t need to communicate to each other. In this situation, the UIC682 acts like a general magnetic stripe card reader whenever it senses the card, it will try to decode the card data automatically and send the decoded data to the host if the process is successful. Otherwise, no information is sent out. If the application would like to take whole control on the reader, it is recommended using the “Host Polled” mode instead of the “Self-ARM” mode. It can be done by either sending “Self-ARM” disable command or changing default setting in the reader configuration. Once UIC682 receives the Self-ARM disable command, H0 (see the command description section), it turns off auto-read function and waits for the “Arm-to-Read” command, P, for next transaction. Since the Self-ARM disable command won’t change the EEPROM setting, UIC682 will turn back to Self-ARM for next power cycling. Besides, the Self-ARM enable command, H1, can also bring UIC682 back to Self-ARM. To disable Self-ARM mode permanently, the host needs to set the EEPROM value of UIC682. The configuration command SAx (x = E or D, see the Configuration Guide) saves the setting into the EEPROM of UIC682 and keep the value until next changed. Meanwhile, it is recommended using the Protocol 2 (USI2) for “host polled” application because USI2 contains the header, message counter and block check character. It is better than Protocol 0 (USI0) and Protocol 1 (USI1) to prevent the data to be misinterpreted but needs more redundant bytes. 5-1
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 Host Polled Application Example A. UIC682 setting changed In this example, it assumes UIC682 is in factory default and the user would like to change it to protocol USI2 and Self-ARM disable. Initial State 1. Send the configuration command to set UIC682 to protocol 2. 2. Send the configuration command to set UIC682 to Self-ARM disable. Done This process should be done only once to set the UIC682 to the proper state. Due to the EEPROM life limitation, it is recommended that don’t change the EEPROM value very frequently. Normally, the configuration setting has done in the factory production stage, please contact UIC Sales representative for more detail information. 5-2
UIC682 Programmer’s Manual UDN PM070-U Rev. 1 B. Operation Example In this example, it assumes UIC682 is in protocol USI2 and Self-ARM disable. Read Card Start Send “Arm-to-Read” command to UIC682 Any card read? After host issues the Arm-to-Read command, UIC682 will check if any payment card in the reading read zone or any magnetic stripe card swiped (the magnetic stripe reader is optional device). No matter the card is decoded succeed or failed, it will return ‘^’ to indicate the card has been read. The host can issue Q, R, S command to retrieve the card data. Send Transmit track 1, 2, or 3 command to retrieve track data Card data processing No Yes For next transaction 5-3

Navigation menu