8
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 40319 |
| Application ID | u2IlS9RlhjlJNtvv3TyVWA== |
| Document Description | 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 56.64kB (707964 bits) |
| Date Submitted | 1999-06-04 00:00:00 |
| Date Available | 1999-04-07 00:00:00 |
| Creation Date | 2001-06-18 19:16:36 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-06-18 19:16:38 |
| Document Title | 8 |
FCC II) TAI A7?!
BBC MODEL #6000
SECURITY SYSTEM
INS T ALLA T I ON MANUAL
PRELIMINARY COPY
(APPROVALS PENDING)
AUGUST 1998
BBC Corp,
433 East LinJe Canada Road
St. Paul, MN 55117
Telephone: (612) 490-1936
Fax: (612) 490-0495
Electronic Mail: info@birchbridge.aom
RN. 5. 8/23”!
FCCJD‘ TM A7Pl
1.0 INSTALLATION PROCEDURE STEPS
>>N01'E: We recommend following this installation outline after gaining familiarity with both the
System User and Installation Manuals. (The Installation Manual contains 3 “Ready Reference Guide”.
a small card which has a brief 'st of instnrctions of commonly used features. It also has a System
Installation Sheet (form for listing types and locations of transmitters) on the back of it
1.1 Locate the two System Installation Reference Guide Inserts and the Sample Insert in Section
5.2 of this manual for guidance on entries.
12 Walk through premise with purchaser, determining the number and type of Sensors and their
installation lowtions Discuss location of the Control Panel. Keep in mind tlrat if key FOBs may
be used in the future, the user should be able to hear the status feedback signals from the activation
location. The Panel Status Light should be generally visible. Enter the Sensor location iufonnation
and assigned Sensor number on one of the installation work sheets. (See Sections 2 and 5).
1.3 Install the Control Panel and complete power and telephone connections. Reset the Panel Memory
if required (see Section 5.1), then test Panel operation from all Touch-Tone (1T) telephones by
using the "‘ it "‘ " status request (i.e., enter'l'l' “ fl ‘ ”) (See Section 2).
1.4 Make Program Memory selections for options ' 06, * 07, and ' 08 for best system operation.
>>IMPORTAN T: For belt programming operation, make Tl“ entries alter the speech
prompts. (See section 5.3)
1.5 Find a Work location where a system Touch-Tone telephone is available-cordless phones work
very well. Gather all transmitters and attach the appropriate two-digit Sensor number labels to
each transmitter using the System installation sheet assignments.
1.6 Now assign these Sensor numbers to the System using the procedure outlined in
Section 5.3.
17 Enter the programmed two~digit transmitter numbers (Step 1.6) into the appropriate Sensor
Behavior Groups " 21 through ‘59. (See Sections 6-9}
1.8 Complete the program requirements for Program Memory locations ‘ 60 through "' 71. (See
Sections 10-1 1 for details). When prograrmning is complete, enter TI" “ * 99 " to leave Program
Memory and retum to “Level One—Ofi“.
1.9 At this point, install all the programmed fixed Sensors. Test Sensors by selecting
“ Level 9- Sensor Test ", by entering the operator default Access Code (IT “ # 1234- 9 ”).
Confirm operation by listening for at least four transmision packets (BEEPs) from each
transmitter when activated. (See Section 7 of Users Manual for further details).
1.10 Select Central Station communication test, by enteiing‘l'l' “ it 1234 — 8 ”. (See Section 3 of
Users Manual).
1.11 Familiarize the system user with system operation. Demonstrate changing Access Codes, Chime
option, and status selections, in addition to arming. disarming, and determining status of system by
entering Tl" “ # ‘ “.
1, 12 Familiarize the system user with the following important features:
a) All Sirens are set to Reset alter 4 minutes.
b) An alarm condition will continue to disable the green LED color until the System is reset
(returned to Level One-Ofi). System trouble conditions will also behave in the same way.
Whenever the green LED is off, enter “it” for an announcement of the problem in the detailed
Status Report.
2.0 BBC mo CONTROL PANEL FCC '“ "7" A7”
2.1 CONNECTIONS REQUIRED
2.1.1 TELEPHONE
The Control Panel requires a connection to the telephone line via a special telephone jack
(RI-31x) provided by the alarm or telephone companies, The jack and its wiring provide
complete disconnect fiorn the premise telephones during alarm communications
A telephone ”1" Adapter jack may also be used, but it will disconnect only the telephone
connected into it along side the Panel connection. This hookup does not pmvide the integrity of
the lUjack, as other premise mlephones could block an alarm call if one were “at? hook," keeping
the system from obtaining a dial tone. The telephone line circuit is monitored. Phone Line failure
will be arurunciated as “Phone Line Failure.” It will automatimlly reset when the telephone line is
renamed to neutral.
2.1.2 AC POWER
Operation requires 14 volts DC. This voltage is providedby the l4VDC-,35 amp Class II power
supply that plugs into a non-switched llSVAC-wall outlet. This provides power for operation and
maintaining clnrge on the 12-volt internal battery.
AC power is monitored “Power Failure“ will he annunciated typically within 60 minutes of no
AC Power. It will restore automatically alter AC power is restored,
>>WORTANT1 DISCONNECT THE SYSTEM BATTERY WHEN SYSTEM IS NOT
IN SERVICE. IF AC POWER IS OUT OF SERVICE FOR MORE THAN 16 HOURS,
TECHNICIAN SERVICE MAY BE REQUIRED TO RESTORE THE SYSTEM.
2.2 CONTROL PANEL TAMPER CIRCUIT
The control tamper circuit and system battery test are sofiware selectable in Location ‘89 of System
“Program Memory.” The System powers up with ‘89 "OK." This means that the Panel tamper circuit and
internal battery test will not function. It is rwomrnended that this option be turned On afler the System is
completely installed, the battery connected, AND the System cover screwed on. CAUTION! The tamper
audible annunciation is LOUD-{his could be dangerous to an installer on a ladder, if the System is
activated when the installer is next to it
>>NOTE: Once Tamper and Battery Test is turned On, the System must be Reset (see Section 5.1) to
remove.
2.3 CONTROL PANEL RADIO ANTENNA
The Control Panel Radio Receiver has two internal antennas attaclwd. The antennas will provide adequate
reception for most installations. Installations where Sensors are located 100 feet or more from the Panel
may require use of external antennas. The external antennas provide better radio reception if required Use
ofexternal antennas requires that the internal antennas be removed. The external antenna kit (E. A. K.-l) is
available for this application, Installation instructions are included with the kit.
The external antenna kit should he used in wall mount installations only.
2.4 SELECTING A PANEL LOCATION
Where security is a major concent, the Panel should be located well within the protected area, and wall
mounted as high as possible to discourage tampering. The Panel oelephone and power connections can be
brought in through the backside, or into the lower front of the box, by using surface mounted wire cover
products such as “ Wiremold NMI”. In installations where personal assistance is the primary use, the
Farrel may be located on a tabletop, kitchen counter, or other
Page 2
J‘CC ID: TA] A7l’l
LEAVE ABOUT ONE PAGE FOR DRAWINGS
(TWO DEA WINGS OF PANEL, (COVER OFF AND ON), SHOWING CABLE
CONNECTIONS for POWER, battery, special—left TELCO HOOK UP SHOULD GO HERE.)
RJjack. T adapter. wver cable, Panel‘s 4 pin 2 pin connector, power, battery, and telephone
connections. Point out bus connection, and auxiliary enunciawr interface location
Page 3
FCCll): ‘lAl A7Pl
2.4 SELECTING A PANEL LOCATION (Cont)
convenient location with telephone access and AC power available from a non-switched outlet
Keep in mind the advantage of easy access to viewing the system status light. Hardware for both
tabletop and wall mounting are provided. >>CAUTION. Good radio communication requires
that the Panel not be mounted on metallic wallpaper, or walls with metallic wallpaper or
minors on the backside Installations that use the two-way audio feature should avoid close
proximity to air conditioners, hot air ducts, TV: or radios, and other devices that are
intermittently noisy and could reduce audio reception.
3.0 BBC ALARM SYSTEM PROGRAM OVERVIEW
Alarm system Control Panels are shipped from the Mary with a basic alarm control program installed.
For this prngam to be functional it nwds much more information about the installation. This additional
information (number and type of Sensors, Access Codes, alarm report telephone numbers, etc.) must be
added before the system can be operational. All of this additional information is added at installation time
to a part of the System Program called Program Memory. Organiution is such that Section A. below,
appears first in the program list, then B, then C.
There are three primary sections to Program Memory:
A. The USER Section—Used to control the system operation. It allows the user to enter
custom Access Codes, select status audible gain and voice/tone status format, and select
the Chime feanue. Enter “NNN'N-O" for access.
B. The OPERATING Sectionsted no assign transmitters to groups that have response
characteristics for diflerent types of alarm conditions.
C. The COMMUNICATION Section—has options and information nwessary for alarm
reporting. This includes Central Station telephone numbers digital amount number, two-
way audio option On-Ofl‘ selection, etc.
The M00 System allows the Access Code holder access to Section A only. The alarm maintenance
provider has access to all sections except the user Access Code ponion of section A
3.1 RADIO TRANSMITTERS/SENSORS THEORY OF OPERATION
Radio transmitters are used to the control the system and to sense movement within the premise. All
transmit six~digit Identification numbers, status, and supervisory signals. These signals are referred to as
“radio packets”. Their six-digit 11) number is too cumbersome to relate to the system user. In the Sensor
programming process, we assign this six-digit number to be recognized as part of the system. Once part of
the system, it is rte-assigned a system two-digit ID number. These are the numbers referred to as “Sensor”
numbers.
The “Sensor" numbers are now recognized by the system, and the system has to be told “what to do" when
it hens signals from them We accomplish this by assigning Sensors to “Behavior Groups” in Program
Memory. These groups define specific steps the system will go through upon hearing a Sensor signal
assigned to them. For example, a Call Button (assigned Sensor number 03), my be assigned to group
“M0". On hearing Sensor “03" send an alarm radio packet signal (button pressed), the Panel program will
search for and find Sensor number 03 in group “ ‘40 ”, At this point, the symrn will implement all of the
“40" requirements. The alarm audible will activate. “Help, Help, Call Button 03 Alarm" will be
annunciated (followed by Siren) (along with optional Central Station notification and two-way audio). Any
activated Sensor assigned to group “ ‘40 “ will cause the system to activate inthe same manner, and will
cause the other necessary Alarm steps to be taken
Page 4
> SUMMARY rcc m TM A7Pl
Radio transmitters send a Higit transmitter ID number along with their present status These numbers
must be programmed to be recognized by the system, as part of the system Once rwognized by the Panel,
they are rte-unsigned a two-digit system H) number. The two-digit [D number is then assigned to a
Program Memory System Behavior Group (for example: ‘21, Delayed Intrusion Sensor). The Behavior
Group will determine how the system behaves when a signal fi'om a Sensor assigned to it is received
0 SUPERVISED SENSORS.
All system transmitters emit an hourly supervisory signal. All the Sensor Behavior Groups except for some
portable transmitter grimps monitor for supervisory signals, Supervised grmrps will report a supervisory
failure if a Sensor is not heard from in a twenty-four hour interval.
4.0 SYSTEM PROGRAM MEMORY ACCESS
>>NOTE: System must be in “level 1, Oil“ for times to Program Memory.
>>NOTEz The system will not respond to alarms during programming.
>>NOTE1 You may want to consider delaying any Access Code changes until the installation is
complete, to reduce confusion.
All unprogrammed systems will respond to Technician Default Access Code, “ # 4321 " and user Default
Access Code“ ti 1234
Once in Program Memory and “Program---Prog|arn--" is anntmeiated, a new Technician Code can be
assigned by entering program level ‘ 65, and then following the procedure for entering the new Technician
Access Number (“NNNN). Once programmed with a new number, the Default Technician Access Code
will no longer work.
The BBC Security System memory is programmed using a Touch-Torre telephone either locally or from a
remote location. The programming procedure is the same for each method. The difference is how the
Panel is accessed.
4.1 LOCAL ACCESS
With local access, the system memory is programmed on site, Access to Program Memory requires the use
or the Technician Access Code. Program Memory in an unprogrammed system is accessed as follows:
Enter Default Technician Access Code (Tr “ # 4321 ") or a new Technician Access Code if one
has already been assigned.
“Frogram-~-Program-—Program” is annunciated when Program Memory is accessed
4.2 REMOTE ACCESS
Technician remote programming uses the remote call in feature to gain amass to the system. To do this, the
system user would give the alarm maintenance provider a Temporary Access Code. The technician would
then call the premise following the remote call in procedure, disarm the system. enter the Technician
Access Code, perform maintenance operations, and leave System Arming Level as it was when calling in.
>>IMPORTAN T! The system user must give the service technician an Access Code for system access.
The system user may give a temporary code that is replaced afier service is done. Alter pining system
access. and disamting system, enter the Technician Code the same as is done in local access.
The remote access feature requires that the premise control answer the telephone. The premise Panel will
answer ifeither the Ring—Pause Ring (R—P—R) option or the Twelvelling answer option is used. These
options are described below. (The R—P-R option is programmed to default to “On” when System is
powered up.)
Page 5
FCC IL) TAl A7Pl
4.21 Ring-Pause-Ring ( R-P-R) Option
Call premise. Afier two ring signals, hang up the phone. About 10 seconds later, pick up the phone and
call in again The System will answer after about two rings, alter which “Code Please ---—- Code Please”
will be annunciamd for 20 seconds. During this time, you may enter detailed status ( “ # NNNN ‘ ") or any
other status codes, and the System will work the same as on premise. At this point1 tum System off and
enter Technician Access Code to enter Program Memory.
4.2.1 12 Ring Answer Option
Call premise and let the phone ring 12 times. The System will annunciate “Code Please -—-—- Code Please”.
Follow the none procedure as described in Section 4.2.1 above.
5.0 DETAILED PROGRAMMING PROCEDURES
5.1 SYSTEM PROGRAM RESET
This procedure removes the entire system program and returns selection options back to System “default"
settings. It would typienlly be used at the beginning of a new installation and is required when a system is
taken out of service and reinstalled ina new location. Reset requires disconnecting the system battery and
removing AC power. AC Power is then re-applied while mommtarily pressing the TI“ “* " button on a
system telephone during the first 5 woods of “Power On” (LED blinks during this time). The system will
annunciare a “Ping-Pong“ alert alter the TT “ * ” button is released and Reset is complete. lie-connect the
battery at that point >>MORTAN Tl Remember to bypass the Tamper circuit BEFORE removing
the cover. (Enter “Access Code + 6 + 00” to bypass Tamper). Resetting the System will turn “89
(Panel Tamper and Low Battery detection) 0“. This is the battery test and tamper bypass.
Remember to select this option to “On” again.
5.2 READY REFERENCE GUIDE AND SYSTEM INSTALLATION SHEET
The “Ready Reference Guide” is a small card which has a brief list of instructions of commonly used
featmes. It also has a System Installation Sheet (form for listing types and locations of transmitters) on the
back of it. A sample reproduction of both sides of 3 Ready Reference Guide/System Installation Sheet is
included as Page 7 , This sample should be used as a guide to fill out the necessary system information. A
copy of the System Sensor location and assignment should he folded and inserted in back of the
battery within the Alann Panel box.
Program Memory Group Number (lefl column): This entry defines the Sensor and Call Button Behavior
characteristics, Transmitter Behavior Group numbers are listed in Section 6.0.
Sensor (Device) Identification Number (next column): This entry number is used to identify each Sensor
and Call Button used in the system. Note that many Sensor numbers are not used. Simply leave out entries
for unused Sensor numbers. >>NOTE: To avoid confusion in identifying Sensors, label each Sensor as
it is identified using the attached “Sticky-Bach” labels.
Key Holder information (bottom of sheet): These entries are the responsibility of the system Master Key
holder to fill out It is a good idea to assist users in how to make these entries, but make them aware that the
actual codes are their responsibility.
>>NOTEz The maximum total number or transmitters that can be used in the system is 19. There is no
limit on the number of transmitters that can be assigned to each behavior group as longas the total is 19 or
less. There is no need for numbering Sensors in any kind or order. Only the Control Panel (Sensor 00)
number is pro—assigned.
Pagers
SAMPLE READYREFERENCE GUIDE AND SYSTEM INSTALLA TION SHEET
FCC 11). TM A7l’1
READY REFERENCE GUIDE
huh-M ‘ Copy
- ALL ENTmEs ARE MADE wn'n TOUCH-TOUCH PHONI’.
- NNNN DESIGNATES YOUR ACCESS CODE.
'TO DISARM SYSTEM
To turn off burghry protection.
E-m a NNNN 1
'T0 ARM SYSTEM WHILE IN
PREMISE (guy)
To mm perimnlw sis-mm on, imid: tensor! ofi,
Enter fl NNNN 2
'TO ARM SYSTEM WHILE LEAVING
PEEMJSE (AWAY)
To turn penmmu mum an inside sensors on.
Enter H W I
‘TO CANCEL ACCIDENTAL ALARM
Tn mp sirens and cancel call to Crmnl Swim,
(Telephone Na, 7 - )
Em" a NNNN 1
'TO REMOVE llELAV TIMES
“oom- sown WHEN you "iv
To Am youn SYSTEM
lfyw hat m worm" mind when you try In
um your xynm - mm in upfli. Either aim
the mm, «mm husinglllchypnx
pwudm dawribud below,
my BYPASS A ercmc SENSOR
To turn on syasm with . specific mm ape-L
m" n NNNN 6 ss
>>whm SS is the specific mm In bypus.
‘TO CHECK STATUS OF SYSTEM
To ddnmnine the current pmeaion l=veL
Emu n '
-REMOTE PHONE ACCESS
To mm Symcm from mine location-u. See
Mum-l for filling innmctwns, than:
m: It NNNN ‘ (REMOTE STATUS)
(“INSTAN'I”)
To remove dehy mm in Level 2 a 3. ‘TESTINC YOUR SYSTEM
Enter 5 lath! mm" My time To mm m lhlt your lyslm i. vpzraling Wiy,
you shwld us it frequently (u Inn we each
wzeky Cum-ii your Ownzr's Manual for prose-mm
SYSTEM INSTALLATION SHEET
DATE
"mam DEVICE DEVICE LDCA'HDN
snow» 11) no.
PmAn-i‘md 00 Comm Elm Honr Hlflwny
01
in
us
- 41 M cm Mnn imam
ns
06
~ 11 in Door Sensor Fm-l Mr
- n u Winlw Set-or Del Window-Sum!
- 11 09 Whalw Sen-or Del WInlow-Wul
m 10 T'Tmr Senor lGM-el Em, amp Don!"
-22 11 DoorStnmr Pm DwriBmmelinh-I
-z1 11 Dear Sum Beam-m suing Glul Door
- 35 13 Smolu Samar Balm-l nun-q
- z: u Mouon Sen-or um; Rm Foyer
15
16
17
1:
19
MONITORING FACILITY PHONE N , ALARM SERVICE PHONE N01
CQHHEENTAL CODE LIST: ACCESS com: KEY mm ASSKGNEI) T0
(FUTURE OPTIOM
i" con
2” CODE
Page 7
FCC m. TAl mm
5.3 MEMORY PROGRAMMING
Once the Panel Program is accessed by loul access or remnle access and “Program---Progmm—” is
annuncixted. the Memory is ready in be programmed. Programming the system requires making Tr entries
into the proper locatiuns A description of the entry locations and required entries is given below.
>>NOTE: Wait for completion of voice message before entering ”commands.
>>NOTE: SYSTEM MUST BE IN “LEVEL 1, OFF” FOR ACCESS TO SYSTEM PROGRAM
MEMORY. The system will retum to “Level l, 013" alter 90 seconds of no activity, or an a T1' entry of
”99
Basie Feature Detailed ‘l'l' Dggriptlnn 01
1'1‘ Eutfl Eu!!! Detailed 17ng
“01 tn “01 Access Codes See “ Level 0 " (page 10, User User awess only
Manual)
‘ 03 to ‘05 NOT USED
* 06 Chime (Ping-Pong) “‘ 06 “ Each entry mggles between ON (default)/OFF
ON and OFF (0N-0FF-0N-0FF—,. .)
‘ 07 Audible Gain Status “ ‘ 07 0 “ LOW
“ ‘ 07 l " (Default) MEDIlM
“ ‘ 07 2 " HIGH
' 08 Status Level “ ‘ 08 0 “ Status annuneiated verbally
Announcement only.
“ * 08 1 " (Default) Status annlmciated with
BEEPS.
‘ 09 System entry delay “‘ 09-NN“. where NN is time in Allows time to enter premise
seconds (2 digits). Default is 45 before Alarm activates.
seconds.
Example: “ ' 09-09 " Atler nine seconds delay time
“On” will be enunciated
‘ ID System exit delay “‘ lO-NN " where NN is the time in Allows time to exit before
seconds, up to 60 seconds (2 digits). System is Amied
Default is 45 seconds.
" llto‘ 18 NOTUSED
Page 8
l'CL‘ ll): [7A] A7l’l
5.3 MEMORY PROGRAMME“; (Continued)
Basic
Tr Eng
‘19
‘20
Descrip of Feature
Identifies a Transmitter’r “System Sensor” Number.
>>NOTEz Do this test afier entering all Sensors (‘20) to confirm proper Sensor ID number.
Enter “19". “Begin System Sensor Test" will be annunciated. Activate transmitter slam Shortly utter
last packet “BEEP” is annnnciated, Smsor identification will be annunciated. System returns to Program
Memory 45 seconds utter last entry or new program selection.
Provides for conversion oi“ Cull transmitter’s six-din“; 1D ngmlgr to a two—dig! gym m Number.
System will return to Program Memory afier 45 seconds of no entries.
0 To sssigr a transmitter 11) number to a system sensor number.
Enter “20” in Program Memory. On hearing the annunciation “Enter Sensor”, immediml enter the
Sensor 2-digit number you want to assign to a transmitter. On hearing the annunciation “Begin Sensor
Test", activate an Alarm condition on that transmitter only (packet BEEPs will be annunciated).
Enter 'IT “VF afier hearing the “BEEPing”. “OK" will be annunciated. Repeat same procedure for each
transmitter to be added. This step causes the beginning Sensor to be assigned the Sensor ID Number.
>>NOTE: if a Sensor Number has already been assigred to a Transmitter, “ON” will be replaced
with an “Ooga” snnunciation, and no entry will occur.
a To remove an assigned transmitter 11) and system sensor number:
Enter Tl” “20" in Program Memory. On hearing the annunciation “Enter Sensof’, immediately enter
Tl‘ “ti" followed by the Sensor Number you wish to delete. “OFF" will be annunciated when Sensor
Number has been removed.
>>NOTE: The Sensor Number will also he removed from the group (it any) it was assigned to.
0 To replace a defective transmitter:
Follow the removal and replacement ‘20 procedure described above. Confirm Sensorfl'mnsmitter ID
using ‘19 procedure. Afler this is done, re-enter the Sensor into the group it was previously assigned to.
Example: To remove Sensor “ 03 ", enter Memory ‘ 20, then enter “ # ", then number “ 03". “On”
will be armuncinted. Place Sensor “03” tag on new transmitter. Enter Program Memory ‘20. Alarm
Sensor newly assigned number “03", Afier hearing the Puke! BEEPs annunciated from the
Sensor, enter the TT “ it ". “On" will then be annunciated. Confirm new “03” Sensor ID by using
* 19 Sensor verification procedure. Now re-enter “03" into the appmprinte Behavior Group.
Procedures for programming individual transmitters are as follows:
>DWS: Move magnet toward, and then away from, Sensorreed switch
>Smoke Sensor: Push test button and held for five seconds while Alarm is sounding
>1>ne Place Sensor on a flat surface. pattern facing down. for five minutes. Make sure that no motion
of the Sensor occurs during this time. Then pick up the Sensor and rotate it. This will cause motion to be
sensed, and a transmission to be sent. The five minute delay is necessary because PIR's are designed to
require this “no motion detected“ time in between activations, irt order to conserve battery life,
>>NOTE: This procedure must be followed for all system Sensors. Once this is done, the two-digit
system Sensor numbers (hereafler called Sensor Numbers) must be assigned to the Sensor Behavior
Groups on the following pages.
Page 9
I‘CC 1D. TAI A71’l
6.0 ASSIGMENT OF TRANSMITTERS T0 BEHAVIOR GROUPS
Transmitters can be assigned to Progrnm Loutions in various Behavior Groups, as listed below,
>>NOTE5 The total number of Transmitters that can be used in a system is 19A From zero to all
ninereen transmitters can be assigned (' 21 through ‘ 51). A Sensor Number cannot be assigned to a
group until a transmitter H) number is assign“! to it using the ‘10 procedure. (See Section 5.3).
BEHAVIQR QROUP PRO RAM LOCATION
Intmsion Sensors ‘21 to ‘25 (‘26 to ‘29 NOT USED)
Special Sensors ‘30 to ‘32 (‘33 to ‘34 NOT USED)
Fire Sensors ‘35 (‘36 to ‘39 NOT USED)
Call Buttons ‘40 to ‘45 (‘46 to ‘58 NOT USED)
6.1 TO ADD A SENSOR TO A GROUP
Once a Behavior Group is selected, “Enter Code” will be annunciawd. Sequentially enter the two-digit
numbers of the Sensors to be assigned to it “OK" is annuneiated afier each successful entry. Once all
Sensors in a group are entered, re-select the group. At that time the Panel will annunciate all Sensor
Numbers associated with that Group Number.
6.2 TO REMOVE A SENSOR FROM A GROUP
A Sensor is removed from the system by removing it by using " 20 Program Memory. (See Program
Memory ' 20 for procedure). Doing this will anmmntiully remove it from the assigned group. Re-enter
the Sensor in ‘20, and rc-assign it to the desired group.
6.3 T0 REPLACE A DEFECTIVE SENSOR IN A GROUP
See Program Memory M‘20” procedures.
6.4 TO MOVE A SENSOR FROM ONE GROUP T0 ANOTHER
Entering a Sensor into a Behavior Group
programmed group
I automatically remove it from any previously
Page 10
i-‘cu lL)' TA] A7PI
7.0 SENSORS
7.1 lNTRUSlON SENSORS
These Sensors will activate the Siren, and cause “Intrusion. Intrusion, Sensor NN, Intrusion, Intrusion,
Sensor N'N“ to be annnnciated intermittently with the Siren. The Siren is enabled afier [our minums plus
communication time, but will re-start on detection of a new alarm. The various types of Sensors are
described below:
Delay: Refers to the entry exit delay times explained on page 6 of the Users Manual.
Instant: Refers to alarm activation immediately on Sensor alarm detection
Initiate delay: Refers to Sensors detecting an alarm condition but activating the entry delay
(allowing user time to disarm) instead of causing an immediate alarm.
Delay follower: These are Sensors that will normally cause an “Instant” alarm, but are not active
during delay timesr Some appliwtions are: to provide control protection to use in hallways from
bedrooms to main living area, etc.
Program locations for the various types of Sensors are as follows:
PROGRAM SENSOR GROUP INACTIVE ARMIN ACTIVE ARMIN
LOCATION LEVEQ LEVEL
‘ 21 Door, Window: Initiate Delay ] 2 & 3
‘ 22 Door ,Window, Perimeter: lnstam l 2 & 3
‘ 23 Interior Motion: Delay Follower l, 2 3
‘ 24 Interior Motion: Initiate Delay 1, 2 3
‘ 25 Door ,Windrrw, Interior: Initiate Delay 1, 2 3
"‘ 26 w ‘ 29 NOT USED
Page 11
7.2 SPECIAL SENSORS
I'CC (D: IAI A7I’l
PROGRAM SENSOR INACTIV'E ARMINQ ACTIVE ARMING ALARM
LOCATION GROUP LEVELS LEVELS ANNUNCIATION
“ 30 24 hour “Special". Bypass for of! l, 2,& 3 Siren & “BEEP",
Used for gun “Sensor NN Alarm“,
whinels, stored then Siren
mater homes, etc.
‘ 31 24 hour “Special" Bypass for OH I, 2, &. 3 “BEEP”, “Sensor
Auxiliary. Used NN Alarm",
for water repeated every few
detection, freeze seconds
detection etcr
’ 32 24-hour “special” Bypass for 05 l, 2, & 3 “BEEP", “Serisnr
Used for medicine NN Alarm“,
cabinet, child repeamd every few
ale“, etc No seconds
communication
report.
* 33 to ‘ 34 NOT USED
7.3 FIRE SENSORS
These Sensors activate the fnur-minute time out Audible Alarm. The alarm will re-sum on the detection of
a new alarm event, Thm Sensor: cannot be bypassed. (The Bypass feature is described on page 9).
PROGRAM SENSOR GROUP lNAC’l‘IVE ARMlNG ACTIVE ALARM
LOCATION LEVEQ ARMING ANN UNCIATION
LEVE
‘ 35 FIREHEAT SENSOR Momentary Reset on 1, 2, & 3 Siren and “Fire, Fire,
Return to level 1. Sensor NN"
‘ 36 to ‘ 39 Not used
Page 12
FCC ll) TAI A7l’l
8.0 CALL BUTTON GROUP ASSIGMENTS
Call Buttons that permanently remain on premise are typically programmed to report supervisory failure if
the system does not hear from them at least once in a four-hour period. Silent Buttons are typically used
for break-in or other duress applications, Status audio Level “HEL " Buttons provide Low Level Alert
Alarm in applications where there is no one available to hear aloud audible alarm Choose the application
that best serves the trad.
PROGRAM CALL BU! lgzN GROUP ALARM SOUND AND VQICE ARMmG
LOCATION ANNUNCIATION LVLS
ACTIVE
" 40 Stays on premise. Supervised. Siren and “HELP" with Call 0,1, 2
Button Number annunciated
' 41 - Canberemoved from premise. Siren and “HELP” with Call 0, 1, 2
Unsupervised. Button Number annuncialed.
‘ 42 Stays on premise. Supervised. Status audio level, “HELP” with 0, 1, 2
Call Button Number annunciated.
‘ 43 Can be removed from premise. Status audio level, “HELP" with 0, 1. 2
Unsupervised. Call Button Number armunciated.
‘ 44 Stays on premise, Supervised, Silent Alarm 0, 1, 2
“ 45 Can he removed from premise, Silent Alarm 0, 1, 2
Unsupervised
‘ 46 to ‘ 58 NOT USED
Page 13
9.0 OTHER ASSIGNMENTS
FCC ID. TAI A717]
>>NOTE: SYSTEM INCORPORATES TOUCH-TONE DIALLING ONLY
Basic
‘l'l‘ Entry
‘60
‘61
‘ 62 to *63
*64
‘65
‘66
‘67
‘87
‘88
“89
Feature
Central Station
Telephone Number
Centnl Station back
up number
NOT USED
Central Station
account number
Technician Access
Code
NOT USED
z—Way Radio on.
Central Station reports
(can be used to
remove 2-Way
option).
Enables either Call
Back Option
1. Ring-Pause-Ring
(R-P-R) Option
2. 12 Ring Answer
Option
System 12-Hour
Battery Test and
Control Panel Tamper
Detection,
Detailed TI‘
En!!!
“ N'N...Up to 16 Digits, then “it ",
The number of digits in the telephone
number MUST EXCED four digits.
A“ fl"lnserted withinthefirstfour
digits will program a pause(s), each of
which is annuncinted as “Ping-Pong”,
No entry followed by “ # " will
disable, Alternate attempts, 3 first, 2
second. then repeat for ten mempts
total.
“ “ 64NNNN". Default is “ 0000 ”.
(Assigned Account Number must be
>5000 for BBC Central Station),
“‘ 65 ”, then “NNNN “, then
“NN'N'N' again. Default is “ 4321
“ * 67 " (Default is On).
“ " 87 ” (Default is On).
‘88 (Default is R-P-R Option)
‘89 (Default is “0FF")
Description of
Detailed F re
Toggles between “ON”
and “OFF":
ON: Reports Alarm
Condition, No Restore
Report
Toggles between “ON”
and “OFF’:
Toggles between 1, And 2.
LA LA mfatv W” “
one; 0\ Mme must
be Reset, to turn off.
PACSDXBAN Rev. 5, 8/23/93
Page 14
FCC n): I'A1A7Pl
BBC MODEL #6000
SECURITY SYSTEM
OWNER’S MANUAL
PRELIMINARY COPY
(APPROVALS PENDING)
AUGUST 1998
BBC Corp.
433 East Lillie Canada Road
St. Paul. MN 55117
Telephone: (612) 490-1936
Fax‘ (612) 490-0495
Rcv 54 3/23/93
FCC ID: TAI A7P]
TABLE OF CONTENTS
has
FCC NOTICES z
LIMITATIONS OF ALARM SYSTEMS 3
BASIC COMPONENTS OF YOUR SECURITY SYSSTEM 4
BASIC THINGS YOU SHOULD KNOW
ABOUT YOUR BBC mm SECURITY SYSTEM 5
', ACCESS CODE 5
"r TURNING YOUR SYSTEM OFF: USE THIS
TO CANCEL AN ALARM 5
‘r INTRUSION SELECTIONS 5
; FIRE PROTECTION 6
', SIRENS 6
‘r SYSTEM STATUS LEI) INDICATOR a
} RESET 6
; CALL BUTTONS 7
r ALARM MEMORV 7
BBC SECURITY SYSTEM FEATURES s
l. OPERATOR PROTECTION SELECTION s
2. PROTECTION MODIFIERS 9
3. SYSTEM TESTS 9
4. SYSTEM OPERATION OPTIONS—LEVEL 0 10
5. OTHER TT ENTRIES 11
6. TELEPHONE REMOTE ACCESS II
7. SYSTEM TESTS AND TROUBLE ANNOUNCMENTS I]
Page I
l ‘ I), TAI A71”
FCC NOTICES m“
FCC Pm IS Informs-(inn lo the User
("llzngcs llr modlflcflllum nol Cxpmsfl) appflwud lll BIXL' (Um can vmd Lhc uni-m llulhflffly lll llpcllllc llll: Equlpmenl
FCC Pan 15 Class B
[his elllllplllnnl has bccn lcsled ml] [0qu lo comply will! lln- llllllls fill a (1355BdigiullchlCLLpl-II‘SIMHHO purl I5 urlln- I-(‘C Rules
These llnllls nlc designed lu pruvldc rcasmlahll: pmlcchfln agnmsl lnlcrfelcllccs ln ll rcsillcrllial imlnllallnn
lhix caulpmcnl gcntl‘ales. lllcl. and can lnlllllle rafllfl l'n-llnnnc, cllcrg) and. ll'lml inslnllcu and used ln accordance Wllll Ihe
"l‘ll'llCllOl’h. ma) cause harmful mlcrl‘crcnces lo rudltl (llmllllllllculmns ilowcvcn [here is no gumnlee that lnleflemfllxs wlll not
ncclll ln 3 paniclllar lnsmllallon
ll’lllls eqlllplnenl dues calls: hamlrlll llllcrfflcllcc I0 mlnl nl lnlcmnln reccpllun whlch can he ddcrmlned by lumlng lhe cqnlpnlenl
U" and DI], lhl: uWnCr is encouraged to II) lll carved lhl: lfllcrlrmncc by one (ll’ more nl‘lllc lnllllwlllg measures
Reorlenl ul rcllxalc the rrcclllng antenna
Increase llle wpamllull bellman lhe equipment and lccellcr
Connecl ml- affcclcd qullpmelll and [ht pant] mullel Io scpumll.‘ mlllEia. on llirrunlll branch ulrcmlsl
CUHHI“ the dcalcr or an upcncnced radm/ l V |CC||I||£|dIl fill help
-..
FCC Part 68
Th|> equipmcnl clllnnllCl nilll pm 68 oflhe FCL’ Rum I llcull‘d an lhl: cqulpmcnl Is a lnllcl lllal Contains. nlllllllg ulllel lnrnnnalinn.
Ihc FCC regislrallnn number and "la Ringer Fqunaluncc Nllllllw lRl'N) fill [his cqlllpmcnl lfrcqucsled, lh|s informant)“ lllllsl be
provided 10 Illc lelcphlmt: company
rllc RIIN IS uscd lo delermlnc lhc llmlmnnl mllnbu ill deuce, lhm mu) m- curlnecled m wlll ltlcplmnc lille ln mosl areas, lhc vllm
Lil all dcvicc RFNS should lml tweed five 15 0)
lf|hi> cqlllllnlcnl tausex llnlnl In [ht lclcuhon: ln-lll 01k Iht lclcphollc lllllpllnl llla) lempol’zfll) disconnccl yflur 5chch ll‘posslhlc.
lull “ill be "llllfitd ill adsancc Wllcll adlannc nnlllc l. nlll plalllc .}(\\I will bl: notified as soon as posslhlc You will alsu llc
advlsed maul rlghl l.) file a complalnl mlh the m-
Yllurlclcplwnc compan) Illa) nlnlc Chungcs ln I“ l'acllllln. cqlllplllelll, Upwfllmm. lll procedures lllnl mull] afl'ccl mc pl'vpcf
llpclallml of )(l\|l Cqulpmenl YMI wll bc glvcll naillllccll nullcc lll llldcl lo mnlnlnln ufllfllt‘rnlplcd 5mm
ll‘ flu apenzvlcc lmuhlc willl lhix cnlllpnlenl, plum cnlllncl fllc uflfllpafly llllll inslzllcd lllc cllnlplncm fmmlcc llnd lepalr
mfbmldllon Tim lelt‘phnnc company ln 'a.sk you lo (llscnllllccl ll") cqulplllnnl rnlnl Ihe nclwcrk unlil (he pmblem has been
cnnccled (ll yuu are sun: lhal Ihc tqlllpnlcnl ls llol mall‘ullclllllllllg.
lllls tqulpnlclll may llcll he used nn cllln scr‘lcc l’lmvldcd lll Ihl.‘ lclepllolw company (‘llnnccllon lll pany llnc‘ ll sublet! ln slal:
lallll‘s.
BBC Corp,
4B Easl Linle Canada Road
St. Paul‘ MN 551l7
Telephone: (612) 490-1936
Fax: (612) 490-0495
Electrunlc Mall: info@blrchbridge.com
Page 2
IZICDEUDE
l’LC ll) [Al A7l‘l
LIMITATIONS OF ALARM SYSTEMS
Even the most advanced alarm system cannot guarantee protection againsl burglary, fire. or
environmental problems. Any alarm system is subject to possible compromise or failure-to-warn.
IF:
Sirens are not located within hearing range ol'pcrsons who are asleep,
Sirens are located in remote pans ofthe premise.
Sirens are located behind doors or other obstacles.
Intruders gain access through unprotected points of entry or areas where Sensors have previously been.
Intruders have the technical means or bypassing jamming, or disconnecting all or pan ofthe system.
Power to Sensors is inadequate or is disconnected.
Freeze Sensors or other environmental Sensors are not located in areas where the appropriate condition
can be detected.
Smoke does not reach a Smoke Sensor For example:
0 Smoke Sensors cannot detect smoke in. chimneys, walls, roofs, or areas blocked by a closed door.
0 Smoke Sensors may not warn in time when fires are caused by: smoking in bed, explosions.
improper storage of inflammable materials. overloaded electrical circuits, or other hazardous
conditions.
0 Smoke Sensors may not detect smoke in other levels ofthe building.
Telephone lines are out of service. Telephone lines are also vulnerable to compromise by any of
several means.
The most common cause ofalarm failure is inadequate maintenance. Therefore. test your system at
least monthly to ensure that all Sensors. sirensl and telephone communications are working correctly.
Although you may be eligible for reduced insurance premiums by having an alarm system, your
system is no substitute for insurance.
WAR
G Security system devices cannot compensate you for the loss oflife or property.
Service
[fyou have any questions about your security system. or if you ever need service, please contact your
security consultant:
Company Nameir
Address]
Telephone Number
Page 3
I'CC ID: lAlA7l’]
BASIC COMPO TS OF YOUR SECURITY SYSSTEM
Picture of Control Panel detailing status liglit speaker, mic.
Legend~~ Receives Slams and Control signals from transmitters and premise
telephones. Announces Svstem Status and Alarms. Contains communication and
control electronics and includes standby pgwer.
Picture of Call Button, with necklace. pinned on user clothing lapel, with belt and clip,
Legend—«Universal Call-Button Transmitter.
Picture of DWS
Legend~Door»Window-Sensur {DWS}. Most commonly used transmitter.
Contains a magnetically activated switch that when used with magnet, provides
open-close sensing. Also has provisions for an externall! activated switch input.
Picture of Smoke Sensor
legenvarovides smoke detection and alarm annunciation independent of the
panel annunciation.
Picture of PIR
ngend~Motion Sensor. Detects and reports movement of individuals within its
viewing area. Uses gassive InlraKed Sensing (PIR).
Picture of apical premise telephone
Legend—System can be controlled I)! using your premise telephones or remotely
with an oil-premise Touch-Tune (TT) telephone.
COVEB, with pictures and captions.
Page 4
I'CC II) 'l/\I A7I’l
BASIC THINGS YOU SHOULD KNOW ABOUT YOUR BBC $4600!) SECURITY
SYSTEM
'r ACCESS CODE
Your System is designed to be controlled by using your Touch—Tone (1T) telephone. Control is obtained by
picking up the phone and pushing TT buttons to select the level ofprolectton desired. The results ofthe
entry will be announced over the System speakers, or over the telephone in the case of remote call in.
The #6000 Security System can accommodate two Access Codes. The second code can be temporary and
may be given to alarm maintenance people to gain access for remote programming purposes
Your System IS shipped to work with Access Code " I 234" (DEFAULT Access Code) A Touch-Tone
(TT) “ I! “ I5 entered before the Access Code. then the Level protection desired is entered after the Access
Code; for example, enter “ it 1234 -I " for "Level 1. Off". >>NOTEz This DEFAULT Access Code
number should he changed to your private Access Code as soon as practical. for security purposes. (See
page I0). Touch-Tone entries and resulting Arming Levels are as follows:
T9. U._CH TONE ENTRY M M
“ $1 [234 -l " Level I. Off Resets alarms. Intrusion protection (except 24-hour)
turned Oil"
" it I234 -2 “ Level 2. Stay Intrusion protection with interior Sensors turned Off.
" ii I234 -3 " Level 3. Away All intrusion protection turned on.
" a * “ At any time No change System status audibly annunciatcd.
‘r TURNING YOUR SYSTEM OFF: USE THIS TO CANCEL AN ALARM
Intrusion protection and any alarm conditions can be can be turned OFF by picking up a Touch-Tone
telephone and entering“ t: then your Access Code, then “ I
Example:
ENTER ~> a NNNN .| You will hear "Level 1, mt". (NNNN represents your Access Code).
This procedure is NECESSARY upon enlertttg a premise with tntruston protection on.
Additional measures will likely be required to CANCEL an alarm condition for communicating
alarms. These requirements vary with the monitoring service provider.
SUPPLEM ENTAL “CANCEL” IN FORMATION
i' INTRUSION SELECTIONS
C] PERIMETER PROTECTION--USE WHILE PREMISE IS OCCUPIED
Pick up any phone and enter TOUCILTOHL‘ “ ti NNNN 2
You will hear "BEEP-BEEP, LEVEL 2, STAY ". followed by "LEVEL 2, STAV‘ ON "
after the exit delay time expires.
[1 TOTAL PROTECTION-—USE WHILE PREMISE IS U_NOCCUPIED
Pick up any phone and enter Touch Tone " it NNNN 3 "
You will hear "BEEP-BEEF-BEEP, LEVEL 3, AWAV “. followed by “LEVEL 3, AWAY,
ON " afier the exit delay time expires.
Page 5
El
i‘CC llJ. lAI A7l’l
BBC “000 SECURITY
ASlC THINGS YOU SHO D KNOW ABOUT YO
S EM
INTRUSION SELECTIONS (Cont.)
IF YOU TRY TO SELECT PROTECTION. AND A SENSOR IS “NOT SECURE":
This situation can occur ifa protected window. door, etc, is open, when arming System.
(>>NOT evel 2 does not require interior doors to be armed. These Sensors may be listed as
ut are not used in level 3 protection and their status can be ignored)
Afier entry ofthe Access code and Protection Level. you would hear an annunciatiun ofall
Sensors (ifany) that are not secure.
You can bypass Sensors by entering Access Code « 6 + Sensor number ( TT ~~ NNNN 6 SS").
You will then hear "Sensor SS Hypassed".
Or, you can go to the Sensor and secure it (close door orwindow) and repeat the arming
procedure.
'2' INTRUSION PROTECTION
Several types ot‘Detection Sensors may be used in the System. These include DWS (Door and
Window Switch activated) Sensors, Motion Sensors, and Glass Break Sensors. The Sensors are
usually arranged to provide Perimeter Protection (Sensors arranged at entry points around the
perimeter ofthe premise) and Interior Sensors (provided to pick up any intrusion that escapes the
perimeter detection). The Perimeter Protection usually allows for entry and exit time delays on
frequently used entry points. Entry time delay provides for an adjustable time period upon entry to
reach a telephone to cancel the pending alarm activation. Exit delay allows the user to become
clear ofthe premise before the Intrusion Protection is activated.
"r FIRE PROTECTION
Smoke and/or heat detectors are active in Levels I. 2‘ and 3. Smoke detectors also annunciate a local
audible signal for both alarm and some trouble conditions, The Control Panel supplements the alarm
annunciation and forwards the detector trouble and alarm status in reporting Systems.
‘r SIRENS
All Sirens are set to Reset in about 4 minutes.
’r SYSTEM STATUS LED INDICATOR
The System LED Indicator provides System status information.
The LED will display the System Arming Level status by red blinking patterns:
One blink Level 1
Two blinks Level 2
Three blinks Level 3
2 The light will display a continuous red during test reports and alarm conditions.
3. The red color will disappear during a System trouble condition, or ifthe System was previously in
an alarm condition and the alarm was not cleared (ir e., System returned to “Level Loft").
"r RESET
An Alarm condition that is not returned to Level l, 0" will cause LED green color to be replaced with
red color until System is Reset.
Page 6
tcc 10; MI MN
BASIC THINGS YOU SHOULD KNOW ABOUT YOUR BBC ammo SECURITY
SYSTEM
’r CALL BUTTONS
Call Buttons may be used to summon assistance in reporting Systems. The Control Panel can be
programmed to respond to a pushed Call Button in three different modes. The number in from ofthe
behavior statement indicates the Call Button number in your System that will respond accordingly,
74 Activates a loud "HELP—HELP" annunciation with audible siren alarm. Used to summon assistance
and discourage intruders.
7 Activates a “HELP-HELP“ annunciation only Used when assistance is required, and deterrent
annunciatinns are not necessary.
Activates Silent Alarm, with no annunciatlon. Usually used in reporting Systems for armed robbery
type situations.
r ALARM MEMORY
The System LED indicator green color will extinguish after an alarm condition and remain offuntil the
System is returned to "Level I. Off”. This can be used to provide an alarm caution indica 'on when
observing (hlS condition. Note that the same display will occur for a System trouble condition.
Entering a System status command will cause an annunciation of any previous alarm conditions not Reset,
or present trouble conditions:
1. Enter “rt NNNN "' (works for remote or local access). or
2 Enter "it“ (works for local access only).
Page 7
l'CC ID: TA] A7l’l
BBC SECURITY SYSTEM FEATURES
I OPERATOR PROTECTION SELECTION
>>NOTE: Selection ofarmlng Levels 2 or 3. will cause ALL System Sensors that are “not secure" to be
listed. Level 2 does not require interior doors to be armed, These Sensors may be listed as “not secure", but
are not used in the level 2 proteclion and their status can be ignored.
LEVEL TT ENTRY DESCRIPTION PANEL LIGHT SOUND AND VOICE
tLED] ANNUNCIATION
1 “ # NNNN -l '" System Blinks red Single "BEEP" precedes
Disarmed repeatedly once voice annunciation.
every two
seconds “Level One, Off“ upon
Background entering Level I.
color normally
green, but will
go to "Ofl" ifa
trouble condition
exists,
2 " tit NNNN -2 " Used for Blinks red Double “BEEP" precedes
protection with repeatedly twice voice annunciation
someone in every [W0
premise seconds. "Level Two. Stay" on
(at home) Background entering Level 2.
color normally “Level Two" every four
green. but will seconds during entry time
go to "Off“ ifa until delay time is
trouble condition expired, or System is
exists. disarmed.
"Level Tw0--On” at end
of delay time.
“Level Two--On” when
entry is detected.
3 “ $4 NNNN -3 " Used for Blinks red Triple “BEEP" precedes
protection when repeatedly three voice annunciation.
premise is times every two
vacant seconds. "Level Three, Away" on
Background entering Level 3.
color normally “Level Three" every four
green, but will seconds during entry time
go to "Off” ifa until delay time is
trouble condition expired, or System is
exists. disarmed.
“Level ThreenOn” at the
end ofdelay time.
“Level Three--On" when
entry is detected.
4 NOT USED
Page 8
l'L'C ID TAl A7I’]
BBC SECURITY SYSTEM FEATURES
2. PROTECTION MODIFIERS
LEVEL TT ENTRV DESCRIPTION PANEL LIGHT SOUND AND VOICE
(LED) ANNUNCIATION
5 “Instant" modifier. Entry oI'TT Same as without “Instant“.
" 5 “ during exit delay times of Instant selected.
Level 2 or Level 3 removes entry
delay time. System will revert
back to delays afier reluming to
Level 1.
6 “ # NNNN -6 " Bypass selection. For use in Same as without “Sensor SS Bypassed."
followed by situations requiring a Sensor or Bypass selecled.
Sensor Sensors being bypassed. Enter
Number (SS) TT" NNNN SS " to bypass a
to be specific Sensor. Sensor will w-
bypassed. bypass when Level I selecled.
>>NOTE1 Fire Sensors cannot
be bypassed.
>>NOTE: The Bypass entry
will bypass Sensur‘s tamper
and alarm reporting only.
Transmitter supervisory and
low hatlery detection features
are not effected during bypass.
7 NOT USED
3. SYSTEM TESTS
LEVEL TT._ENTRV w w —
LIGHT LED) ANNUNCI TION
8 " $4 NNNN -8 " >>NOTE: For reporting alarms RED during test “Level 8, Call Test On“.
only. Entry to this level causes a Stays RED afier Test results annunciated
>>N0TEi Central Station communication Ien afier test. “Call Test OK‘i
Accessfb’e test. System will return to Level I unsuccessful or “Call Test failure".
only '," afier successful test. Refer to communication
"Pm‘ng COMMUNICATION TEST (Page attempts).
Sys‘ms 13) for details.
9 “ 41 NNNN -9 " Used for Sensor and Call Butlon RED until “Level 9, Sensor Test On”.
lest. System will return to Level I returned to “ BEEP, SS” on Sensor
after 120 seconds, Refer to Level I. activation.
SENSOR TEST (Page I3) for
details.
Page 9
I'CCID. l‘AlATI’l
BBC SECURITY SYSTEM FEATURES
4. SYSTEM OPERATION OPTIONS-LEVEL 0.
Radio detection is disabled in much of Program Memory
For best results. make TT entries slowly, after lhe voice prompts are done,
LED is solid red during Tesls and Program Memory. System will not respond to alarms during
Programming and Sensor Testi
TT ENTRY DESCRIPTION SOUND AND VOICE ANNUNCIATION
“ # NN'NN-U " For Option 0, enter TT “ $4 NNNN 4] "a (hell "' * NN ” to “Level 0, On”. then “Program—»Progmm"
define the task required: repeated every 5 seconds until after 90
seconds of no TT entries,
Then Enter:
To ASSIGN OR CHANGE USER ACCESS CODES:
TO CHANGE MASTER ACCESS CODE:
“ “ OI “ Enter “ * Ol " and follow audible instructions “Enter New Master Access Code", then
“Enter New Master Access Code again'fi
Then "OK" when complete.
TO ADD OR CHANGE USER CODE 2:
“’ 02 “ Enter " " 02 " and follow audible instructions. “Enter new Access Code“. then “Enter New
Access Code again“. Then "OK" when
complete,
’03 to *05 NOT USED
CHIME SELECTION
~~ * 06 " -- * 06 " tbrCHIME ON/OFF (toggles on entry) “Off’{Default)
STATUS VOLUME
“ * 070 " Enter “* 070 " for STATUS volume LOW “ On" in Low Volume
“ " 07] “ Enter " “ O7I " for STATUS volume MEDIUM "On" in Medium Volume (Default)
“ * 072 “ Enter “ “ 072 “ for STATUS volume HIGH "On" in High Volume
STATUS LEVEL ANNOUNCEMENT
“ ’ 080 " Enter " * 080 " for status level verbal announcement Only "On“
“ * 08] " Enter " * 08] " to add arming level "BEEPs" "On" (Default)
LEAVING PROGRAM MEMORY
“ “ 99 " To leave Program Memory and return to “Level I" “ BEEP”, then “Level 1‘ Off”,
Afler each successful entry in Program Memory. the System
will acknowledge the new selection, When done
programming, enter " " 99 " to return to Level ll
>>NOTE: Enter “ * 99 ” at any time to return to Level 1.
Will return automatically after 1.5 minutes ifthere are
no entries
Page 10
FCC ll): l’AI A7l’l
5. OTHER TT ENTRIES
FEATURE TT ENTRY DESCRIPTION SOUND ANDVOICE
ANNUNCIATIO
System Status " # t “ Annunciates audible status of Typically something such as
System over the loudspeakerts). “BEEP. Level One, Off.
or This includes protection selection Sensor 03 Open AC Power
and tiny abnormal conditions that On“
" it NNNN " “ may exist. See “Abnormal
Conditions“ (Page 7 ) for list.
6. TELEPHO REMOTE ACCESS
The Remote Access feature requires that the premise Control Panel answer the telephone
The telephone is answered ifthe panel Ring-Pause Ring (R—P-R) option is selected. This option is programmed to
default to "On“ when System is powered up
Example: Remote Access Programming using R-P-R answer option:
Call premise. let phone ring two times. then hang up. Wait 10 seconds, then call premise again, Panel will
now answer during first ring signal and annunciatc " Code-"Code" for 12 seconds. then hang up. During
this time. enter “it NNNN * The System will annunciate the present status This is the same
announcement you would receive by selecting System Status (TT “ it * “) from a premise telephone. At this
point, the System will operate the same as it‘you were on premise, The status sound will be annunciated
over the telephone. The premise will automatically hang up phone after 1 minute of no TT entries.
7. SYSTEM TESTS AND TR BLE AN UNCMEN
0 SYSTEM AUTOMATIC TESTS
>>NOTE: Some trouble conditions may require assistance from your security provider for correction.
The System contains many Self-Test routines. Failure ofa test routine will cause a trouble condition. A trouble
condition is indicated by no green color on the System Status Light. An “Degas" sound (trouble alert) followed by
a trouble message identifying the specific trouble will be annunciated when trouble is first recognized. The detailed
trouble announcement will occur during a " til * " TT status request. Trouble conditions will automatically restore to
normal when the trouble is corrected and System is disarmed.
- Sensor Trouble conditions include one or more ofthe following:
El Supervisory failures ( No Signal).
i:i Low battery.
i_i Tamper situations (cover removed).
' Control Panel trouble conditions also include one or more of the following:
El Panel Tamper conditions (cover loosened without Tamper disables).
El AC Power failure.
D Phone Line failure,
El System Low Battery.
Panel running on battery power only will have status LL'D blink status only until low battery is detected.
Page I I
l‘LC ll). l‘Al A7l’l
SYSTEM TESTS AND TROUBLE ANNOUNCME S |C0nt.[
0 SVSTEM AUTOMATIC TESTS (Cont)
- The System Status LED green indication will disappear in “Trouble” and any other abnormal
conditions. including operator selection levels other than Levels I, 2, or 3 and when an alarm
condition exists.
Your Control Panel power is backed up with a rechargeable lZ-volt battery that provides at least 12 hours of
standby power during an AC power failure. AC power failure is not annunciated until the condition persists,
typically for more than halfan hour.
"Sensor low battery and supervisory (no signal) troubles require selecting SENSOR TEST (“ Fl Master Access
Code —9 “), and then activating the Faulty Sensor to clear problem immediately,
>>IMPORTANT NOTE: The “SelfTests” are supplemented with the two Manual Tests listed below, which must
he performed by the System usert
0 SVSTEM MANUAL TESTS
The Manual Tests provide assurances the total System is working. They should be done monthly, and before
leaving the premise for an extended period oftime
- LEVEL 8, COMMUNICATION TEST (Available on reporting Systems only)
Select Communication Test Level 8 by picking up any System phone and entering TT “ it Access Code
(NNNN) -3 You will hear “Begin System Call Test“. Successful test will return System to Level I, and
"Call Test OK. Level 1. on” Will be annunciaied. Ifthe Communication Test is unsuccessful, “Call Test
Failure, Level lo Off“ will be annunciated.
- LEVEL 9, SENSOR TEST
Select Sensor test Level 9 by picking up any phone and entering TT “ ti Access Code
(NNNN)—9 "'. "Begin System Sensor Test“ will be annunciated from System status speakeds). Activate
each System Sensor and Call Button (see Sensor type description (Page 2) for test procedure) and listen for
four or more radio packet BE EPs. Refer to the Call Button and Sensor ID number Location Sheet to locate
all Sensors. Test will return to “Level I" afler 45 seconds ofno Sensor activity. A 2-second loud warning
signal annunciates automatic test time out. A System battery test is automatically done at the end ofthe
test when installer selected.
0 TROUBLE CONDITIONS
A trouble condition will be announced when it is first recognized, The announcement is preceded by an annunciated
“Gaga" trouble alert. The trouble condition will be annuncialed during any TT “ ii ‘ " telephone status request.
slvlnszs dot: Rev 5. 8/23/98
Page I2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:06:18 19:16:36 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:06:18 19:16:38-04:00 Page Count : 28EXIF Metadata provided by EXIF.tools