8
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 40334 |
| Application ID | VOpUvGkLwIwAN5rm9KmLTw== |
| Document Description | 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 56.2kB (702475 bits) |
| Date Submitted | 1999-06-04 00:00:00 |
| Date Available | 1999-04-07 00:00:00 |
| Creation Date | 2001-06-20 18:12:30 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-06-20 18:12:32 |
| Document Title | 40334.pdf |
| Document Author: | jsoscia |
FCC II): TAI 1171’2
BBC MODEL #6000
SECURITY SYSTEM
OWNER’S MANUAL
PRELIMINARY COPY
(APPROVALS PENDING)
AUGUST 1998
BBC Com
433 Ealeinle Canada Road
St. Paul, MN 55117
Telephone: (612) 490-1936
Fax: (612) 490-0495
Electronic Mail: inffibirchbfidgacom
Rev. 5. 8/13/98
FCC lD‘ TAI A7P2
TABLE OF CONTENTS
P_flLe
FCC NOTICES z
LIMITATIONS OF ALARM SYSTEMS 3
BASIC COMPONENTS OF YOUR SECURITY SYSSTEM 4
BASIC THINGS YOU SHOULD KNOW
ABOUT YOUR BBC 56000 SECURITY SYSTEM 5
> ACCESS CODE 5
> TURNING YOUR SYSTEM OFF: USE THIS
TO CANCEL AN ALARM 5
> INTRUSION SELECTIONS 5
> FIRE PROTECTION 6
> SIRENS s
> SYSTEM STATUS LED INDICATOR 6
> RESET 6
> CALL BUTTONS 7
> ALARM MEMORY 7
BBC SECURITY SYSTEM FEATURES s
l. OPERATOR PROTECTION SELECTION s
z. PROTECTION MODIFIERS 9
3. SYSTEM TESTS 9
4. SYSTEM OPERATION OPTIONS—LEVEL o 10
5. OTHER 11 ENTRIES 11
6. TELEPHONE REMOTE ACCESS 11
74 SYSTEM TESTS AND TROUBLE ANNOUNCMENTS II
Page 1
FCC ll): TAl A7P2
FCC NOTICES
FCC Part 15 Information to the User
clunger or mndineetione net expreerly rpproved by BBC chip. inn void the “let's eutnnrityte ope-me the equipment.
FCC Part 15 glass B
ntir equipment lux been tested end foundto comply with the Iimiu for . clue B digirnl devioe, purulent to pan ls ofthe FCC Rules.
These limitn ere deeignedto provide reeeotuhle protection erg-inn interferences rn eresidentinl indullntiun.
Thit equipmeen generates. mu, end our mdine mdio frequency energy end. if not innelled uni used in noon-dance with the
inslnlflmm, mey eeuee herrnlul irtterrereneei to mdro eommunieetinmr However. thee is no gunmen thnt interference. will not
new in e pertieuler innnlletion.
lfthis equipment does eoute lumtfill interference to udlo or television reception. which an he determined by hinting the equipmern
ofiend on the owner in encnmged totry to correct the interference by one or more otthe following meeuuree:
. Reon'enl or reloeete the repeating men-re
. [nu-ease the eepemion between the equipment and “velvet
. chm-en the infected equipment end the panel receiver to repel-ate outlett, on difi'erem hmneh errouite.
- Duns-ll! the deeler oren experienced rodiorrv teehnieien for help.
FCC Part 68
This equipment emplies with pm on orthe FCC Rules. Located on this equipment in . lehel thrt cumin-s, lmrmg other hifonnetion.
the FCC regirtmtinn numher end the Ringer Equiveleriee Number (REN) forthir equipment. "requested, this inrmnetion mm. be
provided lathe Ielephune eumpnny.
The REN is used In damnine the maximum number of device; that may be connectedw your telephone line. In most are”, the sum
oflll device KENS xhwld not exceed five (3.0).
lrthie equipment eel-nee ham-l to the telephone network. the telephone eornpeny mny tempnmily direonneet your eerviee, lfpcuible,
you will he notified in edvmee. When Idvlnce nnfice it not preetiul. you will be notified to soon ls poreihle. You will else he
odvired ofyour right to file it eompletnt with the FCC.
Your telephone oomperry my nuke changed in in facilities, equipment. overihons, or procedrtreethnt eeuld efieol the proper
openlion ofywl equipment You will be y'ven edveneed nmice in order to meirnhin unlntnrupted med
Ifyou expu'ime trouhle with this equipment, plme cunt-a the compmy tit-t installed the equipment for servlee and rep-ir
infatuation. The telephone eonrpeny may eslr you to dieeonneet thir equipment hont the nettvonr until the problem hot hem
corrected or you are rurethetthe equipment it not nulfilnctioning.
This equipment: my not he need on eoin tmiee provided hytheteleplrone eompeny. Connection to petty linet is mhject to rule
tariffs.
BBC Corp,
433 East Little Canada Road
St. Paul, MN 55117
Telephone: (612) 490-1936
Fax: (612) 490-0495
Electronic Mail: info@birchbridge.com
Page 2
GDGDGDE
El
l-‘Ct'ID: I'A1A7I’2
LIMITATIONS F ALARM SYSTEMS
Even the most advanced alarm system cannot guarantee protection against burglary, fire, or
environmental problems. Any alarm system is subject to possible compromise or failure—to‘wam,
IF:
Sirens are not locawd within hearing range of persons who are asleep.
Sirens are located in remote parts of the premise.
Sirens are loaned behind doors or other obstacles.
Intruders gain access through unprotected points of entry or areas where Sensors have previously been.
Intruders have the technical means of bypassing, jamming, or disconnecting all or part of the system.
Power to Sensors is inadequate or is disconnected.
Freeze Sensors or other environmental Sensors are not located in areas where the appropriate condition
can be detected.
Smoke does not tench a Smoke Sensor. For example:
0 Smoke Sensors cannot detect smoke in: chimneys, walls, roofs or areasblockod by a closed door.
0 Smoke Sensors may not warn in time when fires are caused by: smoking in bed, explosions,
improper storage of inflammable materials, overloaded electrical circuits, or other hazardous
conditions.
0 Smoke Sensors may not detect smoke in other levels of the building.
Telephone lines are out of service. Telephone lines are also vulnerable to compromise by any of
several means.
The most common cause of alarm failure is inadequate maintenance. Therefore, test your system at
least monthly to ensure that all Sensors, sirens, and telephone communications are working correctly.
Although you may be eligflale for reduced insurance premiums by having an alarm system, your
system is no substitute for insurance.
WARN G: Security system devices cannot compensate you for the loss of life or property.
Service
lfyou have any questions about your security system, or if you ever need service, please contact your
security consultant:
Company Name
Address
Telephone Number
Page 3
I'Ct? IL), l‘A] A7I’Z
BASIC COMPONENTS OF YQUR SECURITY SYSSTEM
Pictpg of Control Ppnel detailing status light, speaker, mig.
Legend-m Receives Status and Control signals from transmitters and premise
telephones. Announces nggm Status and Alarms. Contains communication and
control electronics and includes standby power.
Picture of Call Bpgpn, with nggklpce, pinned on user clothing lapel, with belt and glip,
ngend-—Universal Call-Button Transmittgr.
Picture of DWS
Legeng-~Door-Window-Sensor |DWS|. Mpg gommonlx pgd transmitter.
Contains a magnetically activated switch that when used with magnet, provides
emu-close sensing. Also llgs provisions for an externallx activated switch inppt,
Picture of Smoke Sensor
Legend—Provides smoke detflign and alarm annunciation independent of the
panel annpnciation.
Picture of HR
Le en Motion nsnr. Detects and re orts movement 1“ individual within its
viewing area. Uses Passive lnt'raged Sensing (PlR).
Pictureof ical remi e hon
ngendn-sttem can be controlled by using pppr premisg telephones or remote]!
with an off-premise Touch»Tone (T! iteleplmne.
COVER with ictures an a lions.
Page 4
FCC ID: lAl A7l’2
BASIC THINGS YOU SHOULD KNOW ABOUT YQUR BBC #6000 SECURITY
§YSTEM
> ACCESS CODE
Your System is designed to be controlled by using your Touch-Tone (IT) telephone, Control is obtained by
picking up the phone and pushing Tl" buttons to select the level of protection desired. The results of the
entry will be announced over the System speakers, or over the telephone in the case of remote call in.
The #6000 Security System can accorrunodale two Access Codes, The second code can be temporary and
may be given to alann maintenance people to grin access for remote programming purposes.
Your System is shipped to work with Amss Code “1234" (DEFAULT Access Code). A Touch-Tone
(TI‘) “ it " is entered before the Access Code, then the Level protection desired is entered alter the Awess
Code; for example, enter “ it 1234 -l " for “Level 1, Oil". >>NOTEz This DEFAULT Access Code
number should he changed to your private Access Code as soon as practical, for murky purposes. (See
page 10). Touch-Tone entries and resulting Arming Levels are as follows:
TOUCH TONE ENTRY ARMING LEVEL ACTION
“ It 1234 -l " Level 1. Off Resets alarms Intrusion protection (except 24-hour)
turned Off
“ It 1234 -2 ” Level 2, Stay Intrusion protection with interior Sensors turned OE.
“ # 1234 -3 " Level 3, Away All intrusion protection turned on.
“ fl “ " At any time No change System status audibly armunciated.
> TURNING YOUR SYSTEM OFF: USE THIS TO CANCEL AN ALARM
Intrusion protection and any alarm conditions can be can he turned OFF by picking up a Touch-Tone
telephone and entering “ # ”, then your Access Code, then“ 1 ".
Example:
ENTER “ ti NNNN -l You will hear “Level I, OH“. (NNNN represents your Access Code).
This pmdure is NECESSARY upon entering a premise with intrusion protection ON.
Additional measures will likely be required to CANCEL an alarm condition for communicating
alarms These requirements vary with the monilo_ri_ng service provider.
SUPPLEMENTAL “CANCEL” INFORMATION
> INTRUSION SELECTIONS
El PERMETER PROTECTION—USE WHILE PREMJSE IS OCCUPIED
Pick up any phone and enter Touch-Tone “ # NNNN 2 ”.
You will hear “BEEP-BEEP, LEVEL 1, STAY ”, followed by “LEVEL 2, STAY, ON "
afier the exit delay time expires.
D TOTAL PROTECTION—USE WHILE PREMISE IS QOCCUPIED
Pick up any phone and enter Touch Tone “ # NNNN 3 ”.
You will hear “BEEP-BEEP-BEEP, LEVEL 3, AWAY followed by “LEVEL 3, AWAY,
ON ” alter the exit delay time expires.
Page 5
FCC 11). TM A7l’2
BASIC THINGS YOU SHOULD KNOW ABOUT YOUR BBC mo SECURITY
SYSTEM
> INTRUSION SELECTIONS (Cont)
n IF YOU TRY TO SELECT PROTECTION. AND A SENSOR IS “NOT SECURE”:
This situation can occur if a protected window, door. etc, is open, when arming System.
(>>NOTE: Level 2 does not require interior doors to be armed. These Sensors may be listed as
"Not Secure”, but are not used in level 2 protection and their status can be ignored).
Alter entry of the Access code and Protection Level, you would hear an annunciation of all
Sensors (ifany) that are not secure.
You can bypass Sensors by entering Access Code + 6 + Sensor number ( IT “ NNN'N 6 SS”).
You will then hmr “Sensor SS Bypassed”.
Or, you can go to the Sensorand secure it (close door or window) and repeat the arming
procedure.
0 INTRUSION PROTECTION
Several types of Detection Sensors may be used in the System. These include DWS (Door and
Window Switch activated) Sensors, Motion Sensors. and Glass Break Sensors. The Sensors are
usually arranged to provide Perimeter Protection (Sensors arranged at entry points around the
perimeter of the premise) and Interior Sensors (provided to pick up any intrusion that escapes the
perimeter detection) The Perimeter Protection usually allows for entry and exit time delays on
frequently used entry points. Entry time delay provides for an adjustable time period upon mtry to
reach a telephone to cancel the pending alarm activation. Exit delay allows the user to become
clear of the premise before the Intrusion Protection is activated,
> FIRE PROTECTION
Smoke and/or hut detectors are active in levels 1, 2, and 3. Smoke detectors also annuneiate a local
audible signal for both alarm and some trouble conditions. The Control Panel supplements the alarm
annunciation and forwards the detector trouble and alarm status in reporting Systems.
> SIRENS / mm a/fiwf Li I“ V" L.
i , U (l ,.
“WU-1," é'u‘F} ’ "
All SirenssresettoResetinabmrMminutes.
> SYSTEM STATUS LED INDICATOR
The System LED Indicator provides System status information:
1, The LED will display the System Arming Level status by red blinking patterns:
One blink Level 1
Two blinks Level 2
Three blinks Level 3
2. The light will display a continuous red during test repons and alarm conditions.
{or ii
3. The I color will disappear during a System trouble condition, or ii‘the System was previously in
an alarm condition and the alarm was not cleared (i. e., System returned to “Level l, 013").
> RESET
An Alarm condition that is not returned to Level 1, Off will muse LED green color to be replaced with
red color until System is Reset.
Page 6
FCC 1D: TA! A7l’Z
YSTEM
> CALL BUTTONS
Call Buttons may be used to summon assistance in reporting Systems. The Control Panel can be
programmed to respond to a pushed Call Button in three difl'erent modes, The number in front of the
behavior statement indicates the Call Button number in your System that will respond accordingly.
_ Activates a loud “HELP—HELP annunciation with audible siren alarm. Used to summon assistance
and discourage intruders.
_ Activates a “HELPJ-ELP” annullciatjon only. Used when assistance is required, and deterrent
nnnunciations are not necessary.
_ Activates Silent Alarm, with no annunciation. Usually used in reporting Systems for armed robbery
type situations.
> ALARM MEMORY
The System LED indicator green color will extinguish afier an alarm condition and remain off until the
System is retumed to “Level 1, Off”. This can be used to provide an alarm caution indication when
observing this condition. Note that the same display will occur for a System trouble condition.
Entering a System status command will cause an armunciation of any previous alarm conditions not Reset,
or present trouble conditions:
1. Enter “it NNNN "’ (works for remote or local awess), or
2. Enter “It“ (works for local amass only).
Page 7
FCC ll). TAI A7l’2
BBC SEQURITY SYSTEM FEATURES
1. OPERATOR PROTECTION SELECTIQN
>>NOTE: Selection of arming Levels 2 or 3, will muse ALL System Sensors that are “not secme” to be
listed. Level 2 does not require interior doors to be aimed These Sensors may be listed as “not secure", but
are not uwd in the level 2 protection and their status can be ignored
LEVEL TTENTRY DESCRIPTION PANEL LIGHT §QQND AND VOICE
jLED! AN NUNCIATIQN
1 “ fl NN'NN -I " System Blinks red Single “BEEP” precedes
Disarmed repeatedly once voice annunointion.
every two
seconds. “Level One. Olf’ upon
Background entering Level 1.
color normally
green, but will
go to ‘Ofl" if a
trouble condition
exists.
2 “ # NNNN -2 " Used for Blinks red Double “BEEP" precedes
protection with repmledly twice voice annunciation.
someone in every two
premise seconds. “Level Two, Stay" on
(at home) Background entering Level 2,
color normally “Level Two" every four
green, but will seconds during entry time
go to “on“ if at until delay time is
trouble condition expired, or System is
exists. disanned.
“Level Two-On” at end
of delay time.
“Level Two-On” when
entry is detected.
3 “ # N -3 " Used for Blinks red Triple “BEEP“ precedes
protection when repeatedly three voice annnnciation,
premise is times every two
vacant mounds. “Level Three. Away" on
Background entering Level 3.
color nomially “Level Three” every four
green. but will seconds during entry time
go to “on" if a until delay time is
trouble condition expired, or System is
exists. disanned.
“Level Three—On” at the
end of delay time
“Level Three-On" when
enuy is detected.
4 NOT USED
Page 8
2. PROTECTION MODIFIERS
LEVEL
TT ENTRY
“ # NNNN —6 "
followed by
Sensor
Number (55)
to be
bypassed.
3. SYSTEM TESTS
LEVEL
>>NOTE:
Accessible
only in
reporting
Systems
TI” ENTRY
“#NNN'N-8”
“#NNNN-9"
DESCRIPTION
“Instant” modifier. Entry of T1"
“ 5 " during exit delay times of
Level 2 or Level 3 removes entry
delay time. System will revert
back to delays afier retuming to
Level 1.
Bypass selection. For use in
situations requiring a Sensor or
Sensors being bypassed, Enter
Tl'“NN‘N‘N SS "tobypassa
specific Sensor. Sensor will u-
bypass when Level 1 selected.
>>NOTE: Fire Sensors cannot
be bypassed.
>>NOTE: The Bypass entry
will bypass Sensor’s temper
and alarm reporting only.
Transmitter supervisory and
low battery detection infirm
are not effected during bypass.
NOT USED
DESCRIPTION
>>NOTE: For reporting alarms
only. Entry to this level causes a
Central Station immunisation
test. System will renu-n to Level I
alter snweessfu] test. Refer to
COMZMU'N'ICATION TEST (Page
13) for details.
Used for Sensor and Call Button
test. System will return to Level I
afler 120 seconds. Refer to
SENSOR TEST (Page 13) for
details.
Page 9
rec 11): TA] A7l’2
BBC SECURITY SYSTEM FEATURES
PANEL LIGHT
(LED)
Same as without
Instant selected.
Same as without
Bypass selected.
PANEL
mm
RED during test
Stays RED alter
ten
unsuccessful
communication
attempts).
RED until
returned to
Level 1.
NI) AND VOICE
Ml!
“Instant”,
“Sensor SS Bypaswd."
SOUND AND VOICE
mm
“Level 3, Call Test On".
Test resuns annuneiated
afier test. “Call Test OK”,
or “Call Test iailure‘.
“Level 9, Sensor Test On".
“ BEEP, SS" on Sensor
activation.
I-(.(_' 11) TM A7l’2
BBC SECURITY SYSTEM FEATURES
4. SYSTEM OPERATIQ OPTIONS-LEVEL 0.
Radio detection is disabled in much of Program Memory.
For best results, make Tl” entries slowly, after the voice prompts are done.
LED is solid red during Texts and Progrlm Memory. System will not respond to alarms during
Programming md Sensor Test.
TT ENTRY DESSZRIPTION
“ it NNNN-O ” For Option 0, enter TT “ it NNNN 4) ”, then “ ‘ NN ” to
define the task required:
Then Enter:
To ASSIGN OR CHANGE ! §ER ASXQE§§ CODES:
TO CHANGE MASTER ACCESS CODE;
“ * 01 " Euler “ ‘ 01 ” and follow audible instructions.
TO ADD QR CHANGE USER CODE 2:
“* 02 ” Enter “ ‘ 02 " and follow audible instructions.
‘03 to *05 NOT USED
CRIME SELECTION
“ t 06 " “ * 06 " for Cl-llME ON/OFF (toggles on entry)
STATU§ VOLQ ME
“ ‘ 070 “ Enter “" 070 " Int STATUS volume LOW
“ ' O71 “ Enter “ ‘ 071 ” for STATUS volume MEDIUM
“ ‘ 072 " Enter “ ‘ 072 " for STATUS volume HIGH
STATUS LEVEL ANNOUNCEMENT
“ "‘ 080 " Enter " * 080 " for status level verbal announcement onlyl
“ ‘ 081 " Enter “ ‘ 081 ” to add arming level “BEEPs”
LEAVING PROGRAM MEMORY
“ ‘ 99 ” To leave Program Memory and return to “Level 1"
Afier each successful entry in Progam Memory, the System
will acknowledge the new selection. When done
programming, enter “ ‘ 99" In retumtnchel l.
>>NOTE: Enter “ ' 99 " at any time to return to level 1.
Will return automatically after 15 minute: if there are
no entries.
Page 10
SOUND AND VOICE ANNUNCIATION
“Level 0, On”, then “Program—Program"
repeated every 5 seconds lllltfl after 90
seconds of no ‘IT entries,
“Enter New Master Access Code”, then
“Enter New Master Awess Code again’t
Then “OK" when complete.
“Enter new Access Code", then “Enter New
Access Code again". Then “OK" when
complete.
“on" (Default)
“ On” in Low Volume
“On” in Medium Volume (Default)
“On" in High Volume
“On”
“On" (Default)
“ BEB’fl then “Level 1, Off “,
l'CC IL)" TAl A7I’2
BBC SECURITY SYSTEM FEATURES
5. OTHER TT ENTRIE
FEATURE 'l'l‘ ENTRY DESCRIPTION SOUND ANDVOICE
ANN [ANCIATION
System Status “ it ‘ " Annuncixtes audible status of Typically something such as
System over the loudspmkefls), “BEEP, Level One, Ofl.
or This includes protection selection Sensor 03 Open. AC Power
and any abnormal conditions that On“
“ # NNNN ‘ " may exist. See “Abnormal
Conditions” (Page 7 ) for list.
6. TELEPHONE REMOTE A S
The Remote Access feature requires that the premise Control Panel answer the telephone
Tire telephone is answered it” the panel Ring—Pause Ring (R-P-R) option is selected. This option is programmed to
default to “On“ when System is powered up.
Example: Remote Access Programming using R-P-R answer option:
Call premise, let phone ring two times, then hang up. Wait 10 seconds, then call premise again. Panel will
now answer during first ring signal and annunciate “ Code—Code“ for 12 seconds, then hang up. During
this time, enter “it NNN'N ‘ ”. The System will armunciate the present status. This is the same
announcement you would receive by selecting System Status (TI‘ “ ti ‘ “) fiom a premise telephone. At this
point the System will operate the same as if you were on premise. The status sound will be annunciated
over the telephone, The premise will umomatically hang up phone alter 1 minute of no TT entries.
7. SYSTEM TEST AND TROUBLE ANN NCMENTS
0 SYSTEM AUTOMATIC TESTS
>>NOTEz Some trouble conditions may require assistance from your security provider for correction.
The System contains many Self-Test routines. Failure of a test routine will cause a trouble condition A trouble
condition is indicated by no green color on the System Status Light. An “Dogs” sound (trouble alert) followed by
a trouble message identifying the wecific trouble will be armunciated when trouble is first recognized. The detailed
trouble announcement will occur during a “ it * ” 1T status request. Trouble conditions will automatically restore to
normal when the trouble is corrected and System is disarmed.
- Sensor Trouble conditions include one or more of the following:
Er Supervisory failures ( No Signal).
El Low battery.
0 Tamper situations (cover removed).
0 Control Panel trouble conditions also include one or more of the following:
El Panel Tamper conditions (cover loosened without Tamper disables).
El AC Power failure.
D Phone Line failure.
El System Low Battery,
Panel running on battery power only will have status LED blink status only until low battery is detected.
Page 11
FCC, ll): >lAl1\7I‘l
7. SYSTEM TESTS AND TROUBLE ANNOUNCMENTS 1Cont.|
0 SYSTEM AUTOMATIC TESTS (Cont)
o Tire System Status LED green indication will disappear in “Trouble” and any other abnormal
conditions, including operator selection levels otherthan Levels 1, 2, or 3 and when an alarm
condition exists.
Your Control Panel power is backed up with a rechargeable ll-volt battery that provides at least 12 hours of
standby power during an AC power failure. AC power failure is not annunciated until the condition persists,
typically for more than half an hour.
“Sensor low battery and supervisory (no signal) troubles require selecting SENSOR TEST (“ ti Master Access
Code —9 "), and then activating the faulty Sensor to clear problem inunediately.
>>HVIPORTAN T NOTE: The “Self Tests” are supplemented with the two Manual Tests listed below, which must
be perfomled by the System user.
0 SYSTEM MANUAL TESTS
The Manual Tests provide assurances the total System is working. They should be done monthly, and before
leaving the premise for an extended period of time
. LEVEL 8, COMMUNICATION TEST (Available on reporting Systems only)
Select Communication Test Icvel 8 by picking up any System phone and entering TI‘ “ # Access Code
(NNNN) -8 ". You will hear “Begin System Call Test”. Successful test will return System to Level 1, and
“Call Test 0K, Level 1, OH" will be annunciated. Ifthe Communication Test is unsuccessful, “Call Test
Failure, Level 1, OH“ will be annunciatecL
- LEVEL 9, SENSOR TEST
Select Sensor nest Mel 9 by picking up any phone and entering 1T “ it Access Code
(NNNN)-9 ". “Begin System Sensor Test” will be annunciated from System status spealter(s). Activate
each System Sensor and Call Button (we Sensor type description (Page 2) for test pmdure) and listen for
four or more radio pocket BEEP; Refer to the Call Button and Sensor ID number Location Sheet to locate
all Sensors. Test will return to =‘Level 1” after 45 seconds of no Sensor activity, A Z-second loud wanting
signal annunciatee automatic test time out. A System battery test is automatically done at the end of the
test when installer selected.
0 TROUBLE CONDITIONS
A trouble condition will be announced when it is first recogniud. The announcement is preceded by an annunciated
“00g!” trouble alert. The trouble condition will be annunciated during any Tl" “ # ‘ “ telephone status request.
SIleEZldoc Rev. 5. 3/23/95
Page 12
rec m TA] A7P2
BBC MODEL #6000
SECURITY SYSTEM
INS TALLA T I ON MANUAL
PRELIMINARY COPY
(APPROVALS PENDING)
AUGUST 1998
BBC Corp
433 Easl Link: Canada Road
Sl. Paul, MN 55] I7
Telephone: (612) 490—1936
Fax: (612) 490-0495
Electronic Mail: info@birchbridge.com
Rev SI run/ox
l‘CClD: TAI A7l’2
1.0 INSTALLATION PROCEDURE STEPS
>>NOTE: We recommend following this installation outline alter gaining famili rity with both the
System User and Installation Manuals. (The Installation Manual conlains a “Ready Reference Guide",
a small card which has a brieflisi ofinstructions ofcommonly used features It also has a System
Installation Sheet (form for listing types and locations oftransmi’tters) on the back ofit.
l 1 Locate the two System Installation Reference Guide Inserts and the Sample Insert in Section
5.2 cfthis manual for guidance on entries,
1.2 Walk through premise with purchaser. determining the number and type of Sensors and their
installation locations, Discuss location ofthe Control Panel. Keep in mind that ifkey FOBs may
he used in the future. the user should be able to hear the status feedback signals from the activation
location. The Panel Status Light should be generally visible. Enter the Sensor location information
and assigned Sensor number on one ofthe installation work sheets. (See Sections 2 and 5),
L3 Install the Control Panel and complete power and telephone connections Reset the Panel Memory
ifrequired (see Section 5. l ). then rest Panel operation fi-orn all Touch-Tone (TT) telephones by
using the “ it ‘ " status request tie. enter TT " it " ") (See Section 2).
1.4 Make Program Memory selections for options " 06. “ 07, and " 08 for best system operation.
>>lMPORTANTz For best programming operation, make TT entries after the speech
prompts. (See section 5 3).
1.5 Find a work location where a system Touch-Tone telephone is available--cordless phones work
very well. Gather all transmitters and attach the appropriate two-digit Sensor number labels to
each transmitter using the System installation sheet assignments.
I.6 Now assign these Sensor numbers to the System using the procedure outlined in
Section 53.
l.7 Enter the programmed twordigii transmitter numbers (Step L6) into the appropriate Sensor
Behavior Groups * 21 through “59. (Sec Sections 6-9).
1.8 Complete the program requirements for Program Memory locations * 60 through * 7l . (See
Sections 10-1 1 for details). When programming is complete, enter TT “ l‘ 99 " to leave Program
Memory and return to “Level One-oft".
1.9 At this point. install all the programmed fixed Sensors. Test Sensors by selecting
“ Level 9— Sensor Test by entering the operator default Access Code (TT " # l234- 9 ”).
Confirm operation by listening for at least four transmission packets (BEEPs) from each
transmitter when activated. (See Section 7 osters Manual for further details).
l.l0 Select Central Station communication test. by entering TT “ it l234 — 8 ". (See Section 3 of
Users Manual).
1.1 I Familiarize the system user with system operation. Demonstrate changing Access Codes, Chime
option, and status selections. in addition to arming. disarming, and determining status ofsystem by
entering TT “ ft ‘
LIZ Familiarize the system user with the following important features:
a) All Sirens are set to Reset after 4 minutes.
to) An alarm condition will continue to disable the green LED color until the System is reset
(returned to Level One-oft). System trouble conditions will also behave in the same way.
Whenever the green LED is off enter “it“ for an announcement ofthe problem in the detailed
Status Report,
Page I
l'( C II). l'Al A7l’2
2.0 BBC 36000 CONTROL PANEL
2.1 CONNECTIONS REQUIRED
2.1.1 TELEPHONE
The Control Panel requires a connection to the telephone line via a special telephone jack
(RJ-3 IX) provided by the alarm or telephone companies. Thejack and its wiring provide
complete disconnect from the premise telephones during alarm communications.
A telephone “T‘ Adapterjack may also be used. but it will disconnect only the telephone
connected into it along side the Panel connection. This hookup does not provide the integrity of
the RJ jack. as other premise telephones could block an alarm call it‘one were “off hook." keeping
the system from obtaining a dial tone. The telephone line circuit is monitored. Phone Line failure
will be annunciated as "Phone Line Failure." It will automatically reset when the telephone line is
returned to normal.
2.l.2 AC POWER
Operation requires I4 volts DC. This voltage is provided by the 14VDC4.35 amp Class ll power
supply that plugs into a non-switched l lSVAC—wall outlet. This provides power for operation and
maintaining charge on the I2-volt |ntemal battery.
AC power is monitored. "Power Failure" will be annunciated typically within 60 minutes ofno
AC Power. It will restore automatically alter AC power is restored.
>>IMPORTANT! DISCONNECT THE SYSTEM BATTERY WHEN SYSTEM IS NOT
IN SERVICE. IF AC POWER IS OUT OF SERVICE FOR MORE THAN 16 HOURS,
TECHNICIAN SERVICE MAY BE REQUIRED TO RESTORE THE SYSTEM.
2.2 CONTROL PANEL TAMPER CIRCUIT
The control tamper circuit and system battery test are sofiware selectable in Location *89 of System
“Program Memory." The System powers up with “89 “Off.“ This means that the Panel tamper circuit and
internal battery test will not function It is recommended that this option be turned On afier the System is
completely installed. the battery connected. AND the System cover screwed on. CAUTION” The tamper
audible annunciation is LOUD—this could be dangerous to an installer on a ladder. ifthe System is
activated when the installer is next to it,
>>NOTE: Once Tamper and Battery Test is turned On, the System must be Reset (see Section 5.I) to
remove.
2.3 CONTROL PANEL RADIO ANTENNA
The Control Panel Radio Receiver has two internal antennas attached. The antennas will provide adequate
reception for most installations. Installations where Sensors are located I00 feel or more from the Panel
may require use of external antennas. The external antennas provide better radio reception if required. Use
ofextemal antennas requires that the internal antennas be removed. The external antenna kit (E. A. K.-1) is
available for th|s application. Installation instructions are included with the kit.
The external antenna kil should be used in wall mount installations only.
2.4 SELECTING A PANEL LOCATION
Where security is a major concern. the Panel should be located well within the protected area, and wall
mounted as high as possible to discourage tampering. ‘Ihe Panel telephone and power connections can he
brought in through the backside. or into the lower t'ront ofthe box. by using surface mounted wire cover
products such as " wiremold NM I ln installations where personal assistance is the primary use. the
Panel may be located on a tabletop. kitchen counter. or other
Page 2
FCC ID: TAI A7l’2
LEAVE ABOUT ONF, PAGE FOR DRAWINGS
(Two DRA WINGS OF PANEL, (COVER OFFAND ON), SHOWING CABLE
CONNE C TIONS for POWER, battery, speaker/ed. TELCO HOOK UP SHOULD GO HERE.)
RJ jack, T adapler, cover cable‘ Panel‘s 4 pin 2 pin connetlor. power, battery, and telephone
connections. Poinl out bus cannsciiom and auxiliary enunciawr interface chalion.
Page 3
I’CC 11) “1A! A7l’2
2.4 SELECTING A PANEL LOCATION (Conn)
convenient location with telephone acccss and AC power available from a non~switched outlet.
Keep in mind the advantage ofensy access to viewing the system status light. Hardware for both
tabletop and wall mounting arc provrded. >>CAUTION. Good radio communication requires
that the Panel not be mounted on metallic wallpaper, or walls with metallic wallpaper or
mirrors on the backside Installations that use the two-way audio feature should avoid close
proximity to air conditioners, hot air ducts. TV's or radios, and other devices that are
intermittently noisy and could reduce audio reception.
3.0 BBC ALARM SYSTEM PROGRAM OVERVIEW
Alarm system Control Panels are shipped from the factory with a basic alarm control program installed.
For this program to be functional it needs much more information about the installation This additional
information (number and type of Sensors. Access Codes, alarm report telephone numbers, etc.) must be
added before the system can be operational. All ofthis additional information is added at installation time
to a part ofthe System Program called Program Memory. Organization is such that Section A, below.
appears first in the program list, then B. then C.
There are three primary sections to Program Memory:
A. The USER Section--Used to control the system operation. it allows the user to enter
custom Access Codes, select status audible gain and voice/tone status format, and select
the Chime feature. Enter “NNNN-O" for access.
B. The OPERATING Section—Used to assign transmitters to groups that have response
characteristics for different types of alarm conditions.
C. The COMMUNICATION Section—-has options and information necessary for alarm
reporting. This includes Central Station telephone numbers. digital account number. two»
way audio option On»0ffseieclion. etc.
The “6000 System allows the Access Code holder access to Section A only. The alarm maintenance
provider has access to all sections except the user Access Code ponion of section A.
3.1 RADIO TRANSMITTERS/SENSORS THEORY OF OPERATION
ttcrs are used to the control the system and to sense movement within the premise. All
git Identification numbers. status. and supervisory signals. These signals are referred to as
“radio packets". Their six-digit ID number is toocumbersome to relate to the system user. In the Sensor
programming process. we assign this six~digit number to be recognized as part ofthe system. Once part of
the system. ll is reassigned a system two-digit ID number. These are the numbers referred to as “Sensor"
numbers.
The "Sensor" numbers are now recognized by the system, and the system has to be told “what to do" when
it hears signals from them. We accomplish this by assigning Sensors to “Behavior Groups“ in Program
Memory. These groups define specific steps the system will go through upon hearing a Sensor signal
assigned to them. For example, a Call Button (assigned Sensor number 03), may be assigned to group
“40". On hearing Sensor "03" send an alarm radio packet signal (button pressed), the Panel program will
search for and find Sensor nuniber03 in group “ ‘40 At this point, the system will implement all ofthe
"MO" requirements. The alarm audible will activate. "Help. Help, Call Button 03 Alarm" will be
annunciated (followed by Siren) (along with optional Central Station notification and two-way audio). Any
activated Sensor assigned to group " NO "' will cause the system to activate in the same manner, and will
cause the other necessary Alarm steps to be taken.
Page 4
.~ 'c m TAl MP2
‘, SUMMARY ‘ L
Radio transmitters send a 6»digit transmitter 1D number along with their present status. These numbers
must be programmed to be recognized by the system. as part ofthe system. Once recognized by the Panel.
they are re-assigned a two-digit system ID numher. The two»digit lD number is then assigned to a
Program Memory System Behavior Group (for example' ‘21. Delayed Intrusion Sensor), The Behavior
Group will determine how the system behaves when a signal from a Sensor assigned to it is received.
0 SUPERVISED SENSORS.
All system transmitters emit an hourly supervisory signal. All the Sensor Behavior Groups except For some
portable transmitter groups monitor for supervisory signals. Supervised groups will report a supervisory
failure it‘a Sensor is not heard from in a twenty-tour hour interval.
4.0 SYSTEM PROGRAM MEMORY ACCESS
>>NOTE: System must be in “Level 1. Of?" for access to Program Memory.
>>NOTE: The system will not respond to alarms during programming.
>>NOTE: You may want to consrder delaying any Access Code changes until the installation is
complete, to reduce confusion.
All unprogrammed systems will respond to Technician Default Access Code. " fit 432] " and user Default
Access Code " tr 1234
Once in Program Memory and “Program———Program annunciated. a new Technician Code can be
assigned by entering program level * 65. and then following the procedure for entering the new Technician
Access Number ("NNNN). Once programmed with a new number. the Default Technician Access Code
will no longer work.
The BBC Security System memory is programmed using a Touch-Tone telephone either locally or from a
remote location. The programming procedure is the same for each method. The difference is how the
Panel is accessed.
4.1 LOCAL ACCESS
With local access, the system memory is programmed on site. Access to Program Memory requires the use
ofthe Technician Access Code. Program Memory in an unprogrammed system is accessed as follows:
Enter Default Technician Access Code (TT “ if 432 I ") or a new Technician Access Code ifone
has already been assigned,
“ProgrammProgram-"Program“ 15 annunciated when Program Memory is accessed.
4.2 REMOTE ACCESS
Technician remote programming uses the remote call in feature to gain access to the system. To do this, the
system user would give the alarm maintenance provider a Temporary Access Code, The technician would
then call the premise following the remote call in procedure. disarm the system. enter the Technician
Access Code. perform maintenance operations and leave System Arming Level as it was when calling in.
>>IMPORTANT! The system user must give the service technician an Access Code for system access.
The system user may give a temporary code that is replaced afier service is done. Afier gaining system
access, and disarming system, enter the Technician Code the same as is done in local access.
The remote access feature requires that the premise control answer the telephone. The premise Panel will
answer ifeither the Ring-Pause Ring (KP-R) option or the TwelveRing answer option is used. These
options are described below. (The RvP-R option is programmed to default to “On” when System is
powered up.)
Page 5
. . TM mm
4.2! Ring—Pause—Ring ( R-P-R) Option l PC in.
Call premise. Afier two ring signals. hang up the phone. About 10 seconds later, pick up the phone and
call in again. The System will answer after about two rings‘ after which “Code Please ----- Code Please"
will be annunciated for 20 seconds. During this time, you may enter detailed status(“ it NNNN “ “) or any
other status codes. and the System will work the some as on premise. At this point‘ turn System otTand
enter Technician Access Code to enter Program Memory.
4.2.2 12 Ring Answer Option
Call premise and let the phone ring 12 times. The System will annunciate “Code Please —--»- Code Please“.
Follow the same procedure as described in Section 4.2.1 above.
5.0 DETAILED PROGRAMMING PROCEDURES
5.I SYSTEM PROGRAM RESET
This procedure removes the entire system progmm and returns selection options back to System “default"
settings I! would typically be used at the beginning ofa new installation and is required when a system is
taken out ofservice and re-installed in a new location. Reset requires disconnecting the system battery and
removing AC power, AC Power is then re-applied while momentarily pressing the TT “* " button on a
system telephone during the first 5 seconds of"Power On“ (LED blinks during this time). The system will
annuneiate a “Ping-Pong" alert afier the TT" ‘ " button is released and Reset is complete. Re-connect the
battery at that point, >>lMPORTANT! Remember to bypass the Tamper circuit BEFORE removing
the cover. (Enter ”Access Code + 6 + 00" to bypass Tamper). Resetting the System will turn *89
(Panel Tamper and Low Battery detection) 0". This is the battery test and tamper bypass.
Remember to select this option to “On" again.
5.2 READY REFERENCE GUIDE AND SYSTEM INSTALLATION SHEET
The “Ready Reference Guide“ is a small card which has a brieflist of instructions ofcommonly used
features. It also has a System Installation Sheet (form for listing types and locations oftransmitters) on the
back ofit. A sample reproduction ofboth sides ofa Ready Reference Guide/System Installation Sheet is
included as Page 7 This sample should be used as a guide to fill out the necessaiy system information. A
copy ofthe System Sensor location and assignment should be folded and inserted in back of the
battery within the Alarm Panel box.
Program Memory Group Number (left column): This entry defines the Sensor and Call Button Behavior
Characteristics. Transmitter Behavior Group numbers are listed in Section 6.0.
Sensor (Device) Identification Number (next column): This entry number is used to identify each Sensor
and Call Button used in the system. Note that many Sensor numbers are not used. Simply leave out entries
f r unused Sensor numbers. >>NOTE: To avoid confusion in identifying Sensors, label each Sensor as
i identified using the attached “Sticky-Back“ labels.
Key Holder information (bottom ot‘sheet): These entries are the responsibility ofthe system Master Key
holder to fill out. It is a good idea to assist users in how to make these entries, but make them aware that the
actual codes are their responsibility.
>>NOTE: The maximum total number of transmitters that can be used in the system is I9. There is no
limit on the number oftransmttters that can be assigned to each behavior group as long as the total is 19 or
less, There is no need for numbering Sensors in any kind oforder. Only the Control Panel (Sensor 00)
number is pre-assigned.
Page 6
Iéc ID. ‘IAI A7P2
SAMPLE READ Y REFERENCE GUIDE AND SYSTEM INSTALLA TIO SHEET
READY REFERENCE GUIDE
Fleh'minnry Cally
. ALL Ewmrzs ARE “Am, WITH Tm ( "DITII puma.
- NNNN DESIGMH ks \ 0! R. A“
‘1 0 DISARM svsnzw nun/a" sown WHEN you TRY
To Ium on burglary pmlcclinn ‘ru ARM ml R s ' l‘l-ZM
Euler # “w l Iryoo hear an "sou sound when you 1on
mm ynur syslem. a unsm is open.
am ARM SVSTEM WHILE IN the sensor. or bynns u Ilslng mo bypass
PREMISE (STAY) prunedurc dm mm below
I'o Ium perImcIcr sensors on. msvdc wnmn on‘
am" a “w 2 "I0 aw. es 4 swarms SE son
.(I tum on syslcm mm aspcclfic msomm
"I 0 ARM SI'STI-zu WIIILE Lmvm; Enter # NNNN 6 x9
PRIZMISE (Awu') >>v\h::rc 55 is Ihe weenie sensor lo bypass
Io (um pcnmeler sensors and msIdc sensors on
Emu- x, xx 1 fro (‘HH‘K s‘rATus or S\'STEM
Io dIflL‘mIIne Inc currcm prmcuion Iml
‘TO CANCEL “(11)an AIARM Enter 14 ,
To slop sirens nml cancel call 10 L'cmml S'Ialmn
(Telephone No 7 , ) «mm: mm: ACCESS
Enter u NNNN I Tuaccess Syslm from lemme locations Sec
Manual for callmg iIIsIrucuons. me..-
"TO REMOVE I) Enttr fl NNNN ‘(REMOTE STA rl'S)
(“INSTANT ")
To rcmuve delay mm m I evel z or s ' I'I.sI INC VDl‘R SYSTEM
a..." 5 during Xl r delay mm To malo- sure um your system IS (mutating proverb;
Mm should lest il frequcnlly (at rem once each
chk) L‘nmull your nwner's Manual for procndnrcs
\ TI‘II
‘ INSTALLATION SHEET
DATE
PROGRAM DEV , DEVICE LOCATION
GROUP ll) ‘40.
I’m-Assigned 00 ( nntrul I‘anel Fim Flour Hallway
01
02
U.)
" AI 04 (all Bullon Parable
05
06
" 2I 07 Door Srnsnr From Donr
" 22 08 Window Rum" Den Winduw-Souln
fl 22 09 VVindlm Semur nu. Window-Wm
‘2I ll] flour S nsor Kilchen llnlry Girage Door
‘22 I] "nor o nsor Putin Door. Busemenl walkout
‘22 12 Dunr fiensnr Bedroom SI j Gllss Door
“ 35 11 Small: Sensor Ballroom Hallway
‘ 23 I4 ‘Iotilm Stnsor Living lem Foxcr
I5
I6
I7
I8
I?
VIOXITORING l'"A(,'lLlT\ l‘lIONE Vt]. ALARM SERV
(70 [DENTAL COHE LI AC 5 CODE KEY 08“ Ag ILNED “l
(FUTURE OPTION)
lfl ("ODE
2” ( ODE
Page 7
FCC, ID: ‘l'AI A7l’2
5.3 MEMORY PROGRAMMING
Once the Panel Program is accessed by local access or remote access and “I’rogram~——Program--” is
annuncialed. the Memory is ready to be programmed. Programming the system requires making T'I‘ entries
into the proper locations. A description ofthe entry locations and required entries is given below.
>>NOTEz Wait for completion of voice message before entering 1T commands.
>>NOTEz SYSTEM MUST BE IN “LEVEL l, OFF" FOR ACCESS TO SYSTEM PROGRAM
MEMORY, The system will return to “Level I, Of‘t“ after 90 seconds of no activity, or on a T1" entry of
”99 n
Basie
TT Entg
*01 lo *02
* 03 to ‘05
“06
‘07
1“08
‘09
*l0
‘Ilto‘lS
Access Codes
NOT USED
Chime (Ping-Pong)
Audible Gain Status
Status Level
Announcement
System entry delay
System exit delay
NOT USED
See " Level 0 " (page I0, User
Manual)
“* 06 " Each entry toggles between
ON and OFF (0N-0FF—ON-OFF-...)
.. 4. 07 0 .‘
" * 07 l "(Beta-lull)
,. y 07 2 ..
“ * OS 0 "
" ‘ 08 I " (Default)
"’ 09-NN". where NN is time in
seconds (2 digits). Default is 45
seconds.
Example: " “ 09-09 “
"’ lO-NN " where NN is the time in
seconds, up to 60 seconds (2 digits).
Default IS 45 seconds.
Page 8
Descrigtion of
Detailed Feature
User access only
ON (default)/OFF
LOW
MEDIUM
HIGH
Status annunciared verbally
only.
Status annunciated with
BEEFS
Allows time to enter premise
before Alarm activates,
Afier nine seconds delay time
“On“ will be annunciated
Allows time to exit before
System is Armed.
FCC ll). liAl A7P2
5.3 MEMORY PROGRAMMING (Continued)
Basic
TT Emu
‘l9
‘20
Description of Feature
identifies a Transmitter‘s “System Sensor" Number.
>>NOTE: Do this test after entering all Sensors (‘20) to confirm proper Sensor lD number.
Enter “’ 19". “Begin System Sensor Test" will be annunciated. Activate transmitter alarmr Shortly afler
last packet “BEEP" is annunciated. Sensor identification Will be annunciated. System returns to Program
Memory 45 seconds after last entry or new progmm selectionr
Provides for conversion ol‘each transmitter’s six-iii it 1D number to a two-digit system H) Number.
System will return to Program Memory after 45 seconds of no entries.
- To assign a transmitter ID number to a system sensor number:
Enter “20“ in Program Memory. On hearing the annunciation “Enter Sensor". ‘mmediateiy enter the
Sensor 2—digit number you want to assign to a transmitter. On hearing the annunciation “Begin Sensor
Test“. activate an Alarm condition on that transmitter only (packet BEEPs will be annunciated).
Enter TT “it" otter hearing the ”BEEPing". "OK” will be annunciated. Repeat same procedure for each
transmitter to be added. This step causes the beginning Sensor to be assigned the Sensor ID Number.
>>NOTE= Ifa Sensor Number has already been assigned to a Transmitter, “ON" will be replaced
with an “Ooga” annuncia ion, and no entry will occur.
' To remove an assigned transmitter ID and system sensor number:
Enter TT ""20" in Program Memory. On hearing the annunciation "Enter Sensor", ‘mmediately enter
TT “ti" followed by the Sensor Number you wish to delete "OFF" will be annunciated when Sensor
Number has been removed.
>>NOTE: The Sensor Number will also be removed from the group (if any) it was assigned to.
0 To replace a defective transmitter:
Follow the removal and replacement ‘20 procedure described above. Confirm Sensor/Transmitter ID
using * I9 procedure. Afier this is done. re-enter the Sensor into the group it was previously assigned to.
Example: To remove Sensor “ 03 enter Memory * 20, then enter “ it ", then number“ 03“. "Off"
will be annunciated. Place Sensor “03“ tag on new transmitter. Enter Program Memory ‘20. Alarm
Sensor newly assigned number “03“. After hearing the Packet BEEPs annunciated from the
Sensor. enter the W" 7: "On“ will then be annunciated. Confirm new "03“ Sensor ID by using
’ I 9 Sensor verification procedure. Now re-enter “03" into the appropriate Behavior Group.
Procedures for programming individual transmitters are as follows:
>DWS: Move magnet toward. and then away from. Sensor reed switch.
>Smoke Sensor: Push test button and hold for five seconds while Alarm is sounding
>PIR: Place Sensor on a flat surface. pattern facing down. for five minutes. Make sure that no motion
ofthe Sensor occurs during this time. Then pick up the Sensor and rotate it. This will cause motion to be
sensed. and a transmission to be sent The five minute delay is necessary because PlR's are designed to
require this "no motion detected" time in between activations, in order to conserve battery life.
>>NOTE: This procedure must be followed for all system Sensors. Once this is done, the twofdigit
system Sensor numbers (hereafier called Sensor Numbers) must be assigned to the Sensor Behavior
Groups on the following pages
Page 9
111", ll)‘ "1 Al A7l’2
6.0 ASSIGMENT OF TRANSMITTERS TO BEHAVIOR GROUPS
Transmitters can be assigned to Program Locations in various BehaviorGroups, as listed below.
>>NOTE: The total number olTransmitters that can be used in a system is 19. From zero to all
nineteen transmitters can be assigned (* 2I through * 51). A SensorNumber cannot be assigned to a
group until a transmitter ID number is assigned to it using the *20 protedure. (See Section 5.3).
BEHAVIOR GROUP PROGRAM LOCATION
intrusion Sensors *21 to *25 (‘26 to ‘29 NOT USED)
Special Sensors *30 to *32 (‘33 to *34 NOT USED)
Fire Sensors ‘35 (*36 to *39 NOT USED)
Call Buttons “40 to ”1504610 *58 NOT USED)
6.1 TO ADD A SENSOR TO A GROUP
Once a Behavior Group is selected, “Enter Code" will be annunciated. Sequentially enter the two-digit
numbers ofthe Sensors to be assigned to it. "OK" is annunciated after each successful entry, Once all
Sensors in a group are entered. re-select the group. At that time the Panel will annunciate all Sensor
Numbers associated with that Group Number.
6.2 TO REMOVE A SENSOR FROM A GROUP
A Sensor is removed from the system by removin ‘t by using * 20 Program Memory. (See Program
Memory " 20 for procedure), Doing this will automatieally remove it from the assigned group. Revenler
the Sensor in *20, and rc—assign it to the desired group.
6.3 T0 REPLACE A DEFECTIVE SENSOR IN A GROUP
See Program Memory “20" procedures
6.4 TO MOVE A SENSOR FROM ONE GROUP TO ANOTHER
Entering a Sensor into a Behavior Group will automatically remove it from any previously
programmed group.
Page [0
l'L‘t'lD. l‘AlA7l‘2
7.0 SENSORS
7.1 INTRUSION SENSORS
These Sensors will activate the siren and cause “Intrusion: Intrusion. Sensor NN. Intrusion, Intrusion,
Sensor NN" to be annunciated intermittently with the Sirens The Siren is enabled after four minutes plus
communitarian time. but will re—slan on detection ofa new alarm. The various types of Sensors are
described below‘
Delay: Refers to the entry exit delay times explained on page 6 ofthe Users Manual.
Instant: Refers to alarm activation immudialely on Sensor alarm detection.
Initiate delay: Refers to Sensors detecting an alarm condition, but activating Ihe entry delay
(allowing user time to disarm) instead of causing an immediate alarmi
Delay follower: These are Sensors that will normally cause an "Instant” alarm, but are not active
during delay times Some applications are: to provide control protection, to use in hallways from
bedrooms to main living area. etc.
Program Locations for the various types ofSensors are as follows:
PROGRAM SENSOR GROUP INACTIVE ARMING ACTIVE ARMING
LOCATION LEVELS LEVELS
* 21 Doori Window: Initiate Delay I 2 & 3
" 22 Door ,Window. Perime|erz Instant I 2 & 3
‘ 23 Interior Motion: Delay Follower l~ 2 3
‘ 24 interior Motion: lniliale Delay 1,2 3
‘ 25 Door .Window. Interior: Initiate Delay I,2 3
‘ 26 lo ” 29 NOT USED
Page II
72 SPECIAL SENSORS
PROGRAM
LOCATION
*30
‘31
‘32
‘3310'34
SENSOR
GRDU P LEVELS
24 hour "Special“. Bypass for Off
Used for gun
cabinets. stored
motor homes. etc.
24 hnur "Special"
Auxiliary. Used
fur water
detection, Freeze
detection. etc.
Bypass for on
24»h0ur "special"
Used for medicine
cabinet, child
alert. etc. No
com mnniculion
report.
Bypass for Ofl“
NOT USED
7.3 FIRE SENSORS
FCC. ll): 'I'/\I A7l’2
INACTIVE ARMING ACTIVE ARMING
LEVELS
1,2,&3
I.2,&3
I,2,&3
ARM
ANNUNCIATION
Siren & “BEE
"Sensor NN Alarm".
then Siren
“BEEP", “Sensor
NN Alarm".
repeated every few
seconds
“BEEP”. “Sensor
NN Alarm".
repeated every few
seconds
These Sensors activate the four-minute nme out Audible Alarm. The alarm will restart on the detection of
a new alan-n event. These Sensors cannot be bypassed. (The Bypass feature is described on page 9).
PROGRAM
LOCATION
‘35
*36to‘39
SENSOR GROUP
FIRE-HEAT SENSOR
Not used
Page 12
man/M
LEVELS
Momentary Resel on
Return to Level I.
ACTIVE
ARMING
LEVELS
l,2,&3
ALARM
ANNUNCIATION
Siren and "Fire, Fire,
Sensor NN"
8.0 CALL BUTTON GROUP ASSIGMENTS
FCC ll) TAl A7I’Z
Call Buttons that permanently remain on premise are typically programmed to report supervisory failure if
the system does not hear from them ill least once in a four-hour period. Silent Buttons are typically used
for break-in or other duress applications. Slams audio Level "HELP“ Buttons provide Low Level Alert
Alann in applications where there IS no one available to heara loud audible alarm. Choose the application
that best serves the need.
PROGRA M
LOCATION
*40
‘4I
1‘42
‘43
‘44
‘45
‘46to‘58
CALL BUTTON GROUP
Stays on premise. Supervised.
Can be removed from premise.
Unsupervised.
Stays on premise. Supervised
Can be removed from premise.
Unsupervised,
Stays on premise. Supervised.
Can be removed from premise.
Unsupervised.
NOT USED
ALA
SOUND AND VOICE
ANN U NCIATIO
Siren and “HELP" with Call
Button Number annunciated.
Siren and “HELP“ with Call
Button Number annunciated.
Status audio level, “HELP" with
Call Button Number annunciated.
Status audio level. “HELP" with
Call Button Number annunciated.
Silent Alarm
Silent Alarm
Page 13
ARMING
LVLS
ME
0,1,2
0.1.2
0,1.2
0.I,2
9.0 OTHER ASSIGNMENTS
FCC lI)‘ TAl A7I’Z
>>NOTE: SYSTEM INCORPORATES TOUCH~TONE DIALLING ONLV
Ba
‘60
‘61
* 62 to ‘63
*64
‘65
‘66
“67
‘87
“88
“39
Fealure
Central Station
Telephone Number
Central Station back
up number
NOT USED
Central Station
account number
Technician Access
Code
NOT USED
Z—Way Radio on.
Central Station repons
(can be used to
remove 2-Way
option).
Enables either Call
Back Option
1. Ring-Pause-Ring
(R-P-R) Option
2. 12 Ring Answer
Option
System IZ-Hour
Battery Test and
Control Panel Tamper
Detection.
Detailed TT
“ NN...Up to 16 Digits. then "it
The number ofdigits in the telephone
number MUST EXCEED four digits.
A " fl " Inserted within the first four
digits will program a pause(s). each of
which is annuneiated as “Ping-Pong“.
N0 entry followed by “ ft " will
disable. Alternate attempts, 3 first, 2
second. then repeat for ten attempts
tolal.
“ ’ 64 NNNN ". Default is “ 0000 ".
(Assigned Account Number must be
>5000 for BBC Central Station).
“‘ 65 then "NNNN ”2 then
“NNNN” again. Default is “ 432] ”.
“ * 67 " (Default is On).
" * 87 " (Default is On).
“88 (Default is R-P-R Option)
*89 (Default is "OFF")
Page 1 4
Description of
Detailed Feature
Toggles between “ON”
and “OFF“:
ON: Reports Alarm
Condition. No Restore
Report
Toggles between “ON"
and “OFF“:
Toggles between 1. And 2.
Once selected, Panel must
be Reset, to turn Off,
PACSOSZJflM Rev 5. 8/23/98
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2001:06:20 18:12:30 Producer : Acrobat Distiller 4.0 for Windows Author : jsoscia Title : 40334.pdf Modify Date : 2001:06:20 18:12:32-04:00 Page Count : 28EXIF Metadata provided by EXIF.tools