Unitech Electronics HT660EBTG PDA Scanner User Manual HT660e 400831G UM V10

Unitech Electronics Co., Ltd. PDA Scanner HT660e 400831G UM V10

User Manual

HT660e Rugged Handheld Terminal - HT660e - User’s Manual400831G Version 1.0

$i Preface About This Manual This manual explains how to install, operate and maintain the HT660e Rugged Enterprise Terminal. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from the manufacturer. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. © Copyright 2011 Unitech Electronics Co., Ltd. All rights reserved. Unitech global website address: http:\\www.unitech-adc.com Bluetooth is a registered trademark of Bluetooth SIG. Microsoft, Windows and ActiveSync are either registered trademarks or trademarks of Microsoft Corporation. Other product names mentioned in this manual may be trademarks or Registered trademarks of their respective companies and are hereby acknowledged. Unitech is a member of Oracle Embedded Software Licensing Program.$

ii Regulatory Compliance Statements FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, avoid direct contact to the transmitting antenna during transmitting. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. FCC Label Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

iii Canadian Compliance Statement This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. European Conformity Statement Declaration of Conformity with Regard to the R&TTE 1999/5/EC and EMC 89/336/ EEC directives. RoHS Statement This device conforms to RoHS (Reduction Of Hazardous Sub-stances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. Taiwan NCC Warning Statement 國家通訊傳播委員會低功率電波輻射性電機管理辦法 (930322) 根據國家通訊傳播委員會低功率管理辦法規定：第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 RF Radiation Exposure Statement: For body worn operation, this phone has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of 0 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.

iv Laser Information The Unitech HT660e series is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The HT660e series contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or during prescribed service operations. The laser safety warning label required by the DHHS/IEC for the HT660e series' optional laser scanner module is located on the memory compartment cover, on the back of the unit. CAUTION! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner will increase eye hazard. Optical instruments include binoculars, microscopes, and magnifying glasses. This does not include eyeglasses worn by the user. Battery Notices The HT660e is equipped with a Lithium-Ion battery pack and backup battery. Both batteries will discharge after an extended period of not being used. When both batteries are discharged, recharge the unit for 12 hours in order to fully charge the main battery and backup battery. Recharge the HT660e through the following: 1. Plug the USB charging cable to the HT660e and plug the 5V/2A AC-DC adapter to the power jack of the USB charging cable. 2. Place the HT660e into the cradle and plug the 5V/2A AC-DC adapter to the power jack of the cradle.

v If the main battery is removed, the backup battery ensures the data on SDRAM is safe for up to 72 hours. To prevent data loss, do not leave the HT660e uncharged with the main battery removed for an extended period. See First Time to Charge the Main Battery & Backup Battery on page 9 for more details. Note: Rechargeable batteries are advised to replace every year or when 500 charge/discharge cycles achieved to guarantee optimal performance. It is normal that the battery balloons or expands beyond one year or the maximum of 500 cycles. Although it does not cause harm, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures. If the performance decrease is greater than 20% in a Lithium-Ion battery, the battery is at the end of its life cycle. Do not continue to use, and ensure the battery is disposed of properly. The length of time that a battery power lasts depends on the battery type and how the device is used. Conserve the battery life through the following:  Avoid frequent full discharges because this places additional strain on the battery. Several partial discharges with frequent recharges are better than a deep one. Recharging a partially charged lithium-Ion battery does not cause harm because there is no memory.  Keep the lithium-Ion battery cool. Avoid a hot car. For prolonged storage, keep the battery at a 40% charge level.  Do not leave the lithium-Ion battery discharged and unused for an extended period because the battery will wear out and the longevity of the battery will be at least shorter than half of the one with frequent recharges. Battery charge notice It is important to consider the environment temperature whenever the Lithium-Ion battery pack is charged. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 10°C to 45°C. Charging batteries outside of the specified range could damage the batteries and shorten their charging life cycle. CAUTION! Do not charge batteries at a temperature lower than 0°C, which will increase the internal resistance to cause heat and make the batteries unstable and unsafe. Please use a battery temperature detecting device for a charger to ensure a safe charging temperature range. Further, to protect and avoid battery from

vi inflating, the battery is detected for thermal protection and will not be charged when the temperature of battery is over 50 degrees. Do not leave the terminal for a long time in the charging cradle and do not charge the battery with a cable long, which will shorten the battery life and cause battery expanding/ballooning. The unit should not be subject to very high temperature, excessive moisture, and direct heat. Avoid the battery from being fully charged and staying in a high temperature environment. Avoid terminal or spare battery from staying in a hot vehicle. For prolonging the storage time, keep the battery at a 40% charge level. Lithium ion batteries oxidize least when they are stored at the state of 40% charge. Storage and safety notice Although charged Lithium-Ion batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens they will require recharging prior to use. Lithium-Ion batteries may be stored at temperatures between -20°C to 60°C, however they may deplete more rapidly at the higher temperature ranges. It is recommended to store batteries within normal room temperature ranges. Warranty The following items covered under Unitech Limited Warranty are free from defects during normal use:  Terminal is covered by 1-year limited warranty.  Cradle is covered by 1-year limited warranty.  Cable is covered by 1-year limited warranty.  Battery is covered by 3-month limited warranty. Warranty becomes void if equipment is modified, improperly installed or used, dam-aged by accident or neglect, or if any parts are improperly installed or replaced by the user. Use only the adapter supplied. Using the wrong adapter may damage the unit and will void the warranty.

vii Table of Contents Preface About This Manual..........................................................................................i Regulatory Compliance Statements.......................................................... ii FCC Warning Statement.................................................................... ii FCC Label Statement ........................................................................ ii Canadian Compliance Statement ..................................................... iii European Conformity Statement....................................................... iii RoHS Statement............................................................................... iii Taiwan NCC Warning Statement ...................................................... iii Laser Information..................................................................................... iv Battery Notices ........................................................................................ iv Battery charge notice.........................................................................v Storage and safety notice ................................................................. vi Warranty .................................................................................................. vi Chapter 1 Getting Started ...............................................................................................1 Introducing the HT660e ............................................................................1 Notice .......................................................................................................1 Warranty............................................................................................2 Regulatory .........................................................................................2 HT660e Model Specification .....................................................................3 HT660e Product Introduction & Accessory Kit ..........................................4

viii HT660e Front View............................................................................5 HT660e Rear View ............................................................................6 First Step with HT660e ......................................................................7 Switch On Backup Battery.................................................................7 Install the Battery Pack......................................................................7 Supply Power to the HT660e.............................................................8 Charge the Battery for the First Time.................................................8 Protective Screen Film.......................................................................9 First Time Use of the HT660e............................................................9 Setting the Time Zone......................................................................10 Setting Date/Time ............................................................................10 Chapter 2 Using the Keypad and Scanner ..................................................................11 Keypad.................................................................................................... 11 HT660e HotKey...............................................................................12 Bar Code Scanner ..................................................................................13 Chapter 3 Power system...............................................................................................14 Charging the Lithium-Ion Battery Pack ...................................................14 Charging the Main and Backup Battery for the First Time ...............14 Environment Consideration for Charging.........................................15 Power Status Indication ...................................................................15 “Backup Battery Low” Icon...............................................................15 Charging the Lithium-Ion Battery Pack ...................................................15 Storage and Safety Precautions .............................................................16

ix Warm Boot / Cold Boot / Factory Default ................................................17 Warm Boot.......................................................................................17 Warm Boot via Software ..................................................................17 Warm Boot via Hardware.................................................................17 Cold Boot.........................................................................................18 Cold Boot via Software ....................................................................18 Clean Boot via Software ..................................................................19 Chapter 4 Data Communication ...................................................................................20 Introduction.............................................................................................20 Connecting..............................................................................................20 Serial or USB Cable.........................................................................20 Cradle..............................................................................................21 Using ActiveSync.............................................................................21 Installation...............................................................................................22 Connecting the Device to Your Computer........................................23 WiFi Connection ..............................................................................24 Bluetooth Connection ......................................................................27 Chapter 5 Useful Utilities..............................................................................................36 Introduction.............................................................................................36 Scanner Setting...............................................................................36 Scan2Key ........................................................................................39 Chapter 6 Device Setting ..............................................................................................40

x Introduction.............................................................................................40 Info...................................................................................................40 Funckey...........................................................................................41 IO.....................................................................................................42 Server..............................................................................................42 Virtual Key .......................................................................................44 Screen .............................................................................................45 Ping .................................................................................................45 CPU.................................................................................................46 Backup.............................................................................................46 Battery .............................................................................................46 Appendix Worldwide Support ......................................................................................48

1 Chapter 1 Getting Started Introducing the HT660e The HT660e is a rugged, compact and ergonomic handheld terminal powered by the WinCE. NET OS to make your work more efficient and profitable. It comes with an integral barcode scanning laser device, color LCD with touch screen, keypad, BT and wireless communication interface capability. It provides the user with a standard Windows-based environment for customization and operation. The following HT660e Product Reference Guide provides simple step-by-step procedures to give you hands-on experience with your HT660e. For programming your HT660e, please refer to our SKD and programming manual. Notice 1. This unit is equipped with a battery pack and backup battery. It is possible that the Unitech HT660e may not be powered ON due to battery discharge as a result of storage. In the above situation and the first-time use, plug the HT660e to the charging cable or charging cradle (with 5V/2A AC-DC adapter), and charge the unused unit for over 12 hours in order to fully charge its backup battery as well. 2. Under normal condition, the back-up battery will be charged from external power or the main battery (if the main battery still has enough power to turn on). If it is charged for the first time, the back-up battery will be fully charged while main battery is charged fully.

2 Warranty Unitech's Limited Warranty provides for different warranty periods for different parts and accessories:  Terminal is covered by 1-year limit warranty.  Cradle is covered by 1-year limit warranty.  Cable is covered by 1-year limit warranty.  Battery is covered by 3-month warranty. Regulatory Compliance with RoHS Certificate includes: CB, CE, CCC, FCC, BSMI, TELEC, VCCI

3 HT660e Model Specification CPU Processor Samsung 6410 / 667mHz Operating System Microsoft Windows CE 6.0 R3 Professional/Core Flash ROM 256MB System MDDR 128MB Keypad Full Alphanumeric 36 keys Weight (g) 360g (with Battery) Enclosure Dimension (LxWxH mm) 199.5 X 79 X 39.6mm (Approximately) Main Battery Type 3.7V / 2200mAH Li-ion, 8.14WH Battery Recharging Time 4 hrs. Battery Life BT / RF disabled  8 hours BT ON / RF OFF  7 hours BT ON / RF ON  8 hours BT OFF / RN ON  Power source Backup Battery Type 120AH Li-polymer Display QVGA 240*320 Color 2.8" TFT LCD display with touch screen Cradle USB or Modem Barcode Scanner Reader 1D Laser Drop 1.5M IP Rating IP 54 Operation Temp. 14℉ to 122℉ (-10℃ to 50℃) Storage Temp. -4℉ to 140℉ (-20℃ to 60℃)Humidity 5%~95% non-condensing Rugged/Environment ESD Contact ± 8KV, Air ± 12KV Communications USB V1.1 Client, PAN Bluetooth V2.1 Class II, WLAN 802.11 b/g (Optional CCX4 certified radio), and Ethernet Cradle Expansion Slot Supporting SD/SDHC memory up to 16GB 802.11b/g Radio Options Bluetooth

4 HT660e Product Introduction & Accessory Kit HT660e Terminal Manual CD Communication Cable Battery Adaptor Kit Hand Strap Stylus Holder

5 HT660e Front View Power Alpha key Indicator Touch Screen Display LED Function key Scan key Communication Interface

6 HT660e Rear View SD Memory Slot Bar Code Scanner Speaker Battery Cover Hand Strap & Stylus

7 First Step with HT660e Before first using the HT660e, please ensure the battery is fully charged. There are three ways to charge your HT660e:  Cradle with one battery charger slot  USB/Charging cable  Rechargeable Lithium-Ion battery pack NOTE: Data loss may occur if the HT660e's backup battery is not adequately charged. Before charging the main battery, make sure the backup battery switch is ON. Switch On Backup Battery Before installing a battery, locate the backup battery switch inside the battery compartment on the left-hand side. Please ensure that it is in the “ON” position before charging the main battery. Install the Battery Pack 1. Remove the battery cover. 2. Move the backup battery switch to the ON position (see the description above). 3. Insert the battery pack so that the contacts on the battery pack line up with the contacts in the battery compartment. Fully seat the battery.

8 4. Cover the battery. Supply Power to the HT660e Connect the USB/Charging Cable to the HT660e and connect the AC adapter to the cable’s power jack and an electrical outlet. Or place the HT660e into the Cradle (first connect the power supply to the Cradle). Charge the Battery for the First Time We would like to propose to charge the battery at least up to 12 hours for the first time to use. While it normally only takes about 4 hours to charge the battery after it's been drained, when charging the battery for the first time please allow at least 16 hours. While charging the main battery the backup battery should also be charged. Please make sure the backup battery has been switched “ON” (this cannot be emphasized enough). CAUTION: There is a high risk of data loss from RAM if the backup battery is not fully charged. This can happen if the main battery has been drained and the unit is not connected to the AC adaptor. For this reason, it is crucial that the backup battery is switched on before charging the main battery for the first time.

9 Protective Screen Film To protect screen, the HT660e has been provided with a protective plastic film. You may remove it (if required). The screen will be more susceptible to scratching without the film, but will be more readable. First Time Use of the HT660e Pressing the Power ON/OFF Key The Unitech HT660e welcome screen appears. The Windows CE screen will appear shortly thereafter. Align the Screen When prompted, use the stylus to tap the targets as they appear in order to align the touch screen. When you complete the procedure, press any key or press anywhere on the touch screen to start up the WinCE system. Adjusting Screen Brightness To adjust the original default setting of the screen brightness, the backlight setting will be required. Please refer to the setting section below for the new setting procedure. Setting Time Zone/ Date Before using the HT660e please take a few minutes to set the time and date so that data can be properly time-stamped.

10 Setting the Time Zone Follow the steps below to set up your time zone. 1. Tap the location arrow to see a list of cities. 2. Choose your location (or nearest listed one). 3. Select the Daylight Savings Time check box, if necessary. 4. Tap the Apply button. If you would like the terminal automatically adjust clock for daylight saving, please tick on it. Setting Date/Time Tap the Left or Right arrows to scroll the year and month you desire. Or, directly tap location of year or month to change the year or month setting. To set up time, tap on the Hr/Min/Sec AM/PM to input the Hr/Min/Sec

11 Chapter 2 Using the Keypad and Scanner Keypad Data can be entered via its 36-key keypad, which includes: 0~9, alpha, function, escape, backspace, enter, scanner trigger, cursor, and on/off keys. Escape Key Enter Key Alpha KeyScan Key Cursor Key Function Key Space Key Tab Key Backspace Key Power Key [ENT] The "Enter" key confirms data entry. [FUNC] The Function Key is used in conjunction with specific number keys to operate as Hotkeys (see next page). [Bksp] The backspace key erases the character to the left of the cursor.

12 [ESC] The escape key returns the user to a previous page. [TAB] The Tab key moves the cursor to the next tab or next control on a form. [Cursor] The cursor key moves the cursor around the screen. [Alpha] The Alpha key toggles Alpha mode and Caps mode. First press of the Alpha key turns the HT660e's keys to input alpha characters, indicated by a blue LED light. A second press turns the input to upper-case characters, indicated by a green LED. A third press returns the HT660e to numeric input. HT660e HotKey The HT660e provides hotkeys for frequently used functions. Press the Function key and the appropriate numeric key for the following functions listed below: Func 6 = Task Manager Func 7 = Scanner Setting Func 8 = Power Properties Func 9 = System Info Hotkeys can be modified to suit the user's preferences. To modify hotkeys, please follow the path below: Path: My computer/Windows/RegFuncKey.exe

13 Bar Code Scanner The HT660e has an integrated 1D laser bar code scanner (depending on model number) capable of reading all major bar code labels.

14 Chapter 3 Power system Charging the Lithium-Ion Battery Pack The HT660e's batteries can be charged via the USB or serial communication cable, or via the optional cradle - both using the included AC adaptor. Please charge the battery for at least 4 hours per session to ensure a full charge. Please note that the first time charge should be for at least 12 hours (see the description below). Charging the Main and Backup Battery for the First Time When first charging the HT660e, please allow at least 12 hours to fully charge both the main and backup batteries. When the HT660e arrives from the factory the backup battery switch is in the OFF position in order to protect the backup battery. Before first charging the HT660e, make sure the backup battery switch is moved to the ON position. The backup battery switch can be found inside the main battery compartment. Data loss can occur if the backup battery is not adequately charged - therefore it is imperative to ensure that the backup battery switch is in the ON position before charging for the first time. A fully charged backup battery can store data for up to 72 hours without power from the main battery. This is not recommended. Please make sure an adequately charged main battery or AC power is presented and try not to rely on the backup battery for other than unusual or emergency situations. To prevent data loss due to backup battery failure (always a slim possibility), please minimize the amount of time that the backup battery has to operate without the main battery pack installed or while disconnected from AC power.

15 Environment Consideration for Charging It is important to consider the environment temperature whenever you are charging the Lithium-Ion battery pack. The process is most efficient at normal room temperature or slightly cooler. It is essential that you charge batteries within the stated range of -5°C to 50°C. Charging batteries outside of the specified range could damage the batteries and shorten their charging life cycle. Power Status Indication When the "Main Batteries Very Low" icon appears, charging the main battery pack as soon as possible is highly recommended in order to avoid system shutdown at an awkward moment. “Backup Battery Low” Icon When the "Backup Battery Low" icon appears, it indicates that the backup battery is low and needs to be charged. Charging the Lithium-Ion Battery Pack Automatic shutdown of the HT660e The HT660e will enter idle mode when there is no task, or all tasks are waiting for input. In default setting, the HT660e will automatically turn itself off if it remains idle for 3 minutes and when there is no external charging power applied. Pressing the power button will return the HT660e to the same point at the time of automatic shutdown. Do not leave the terminal for a long time in the charging cradle and do not charge the battery with a cable long, which will shorten the battery life and cause battery expanding/ballooning. The unit should not be subject to very high temperature, excessive moisture, and direct heat. Avoid the battery from being fully charged and staying in a high temperature environment. Avoid

16 terminal or spare battery from staying in a hot vehicle. For prolonging the storage time, keep the battery at a 40% charge level. Lithium ion batteries oxidize least when they are stored at the state of 40% charge. To save the battery power, it is better to turn off wireless mode. Please follow the steps below to turn off the wireless mode Tap Setting → Control Panel → Device Setting to enter the Device Setting zone. Move to the IO tab and select Disable to disable the wireless mode. Storage and Safety Precautions Batteries should be stored in an open environment and placed where there is no risk of accidental shorting or other damage. Although charged Li-Ion batteries may be left unused for several months, their capacity may be reduced due to back up and internal resistance. If this happens they will require recharging prior to use. Li-Ion batteries may be stored at temperatures between -4°F and 158°F (-20°C to 70°C).

17 Warm Boot / Cold Boot / Factory Default Warm Boot Warm Boot is a reset to re-boot the HT660e without losing saved data. Perform a warm boot when:  The terminal fails to respond.  After installing some software applications  After making changes to certain system settings, such as network cards WARNING - Performing a Warm Boot will result in the loss of all unsaved data! Warm Boot via Software Tap Start → Programs → Utilities →BootMode. Tap “Warm Boot”. The system will be warm started. Warm Boot via Hardware Use a blunt pin (like an unfolded paper clip) to stab the warm-boot pinhole located on the front of the HT660e, below the keypad. warm-boot pinhole

18 Cold Boot Cold Boot is used to reset the operating system and reset the terminal after a bootloader, keyboard, or kernel upgrade. WARNING - Performing a Cold Boot will result in the loss of all data in RAM! Cold Boot via Software Tap Start → Programs → Utilities →BootMode. Tap “Cold Boot”. The system is reset and you will lose all data, including all files, in the RAM memory. You will need to recalibrate the screen and reset the date and time. Cold Boot via Hardware 1. Remove the Main Battery. 2. Switch OFF the Backup Battery. 3. Switch the Backup Battery back ON. 4. Insert the Main Battery. 5. The terminal will restart. 6. Recalibrate the screen and reset the date and time.

19 Clean Boot via Software Clean Boot is used to reset the terminal to factory default settings. WARNING - Performing a Clean Boot will return the HT660e to its original factory settings! Tap Start → Programs → Utilities →BootMode. Tap “Clean Boot”. The system reset the terminal to factory default settings. You will need to recalibrate the screen and reset the date and time.

20 Chapter 4 Data Communication Introduction The Unitech HT660e allows users to link to a host computer via USB, Bluetooth, or Wireless connection for data communication. This chapter provides an overview of the communication of the HT660e. The following subchapters cover these topics:  “Series or USB or Modem” communication via cable or cradle  “RF Communication” for details about wireless communication between the HT660e and host computers  “Microsoft ActiveSync” for details about serial communication via USB port Connecting Serial or USB Cable Plug the USB end of the HT660e communication cable into your PC's USB port, and the other end into the HT660e's communication port. To simultaneously charge the HT660e, plug the AC power adaptor into the power jack of the USB cable.

21 Cradle USB Cradle For data transmission, plug one end of your HT660e's USB communication cable into your PC's USB Port and the other end into the HT660e Cradle's USB port. To simultaneously charge the HT660e, plug the AC power adaptor into the power receptacle on the Cradle. Ethernet Cradle For data transmission, plug telephone line to the RJ45 port of your HT660e cradle. To simultaneously charge the HT660e, plug the AC power adaptor into the power jack on the cradle. Using ActiveSync Using Microsoft ActiveSync, you can synchronize and transfer information between your desktop computer and terminal. The most current version of ActiveSync can be downloaded from www.microsoft.com. Additional Capabilities With ActiveSync, you can also:  Back up and restore your device data.  Copy (rather than synchronize) files between your device and desktop computer.  Control when synchronization occurs by selecting a synchronization mode. For example, you can synchronize continually while connected to your desktop computer or only when you choose the synchronize command.  Select which information types are synchronized and control how much data is synchronized. For example, you can choose how many weeks of past appointments you want synchronized. Before beginning installation, carefully read the following:  Because you will be restarting your computer during installation, save your work and quit all programs before you begin.  To set up your communication settings, the HT660e serial cable is

22 required to connect the HT660e to your host computer.  If you run the Windows NT® operating system with a service pack, you will be informed during setup that you may need to reinstall the service pack. Try connecting first, and if unsuccessful, reinstall the latest service pack. Requirements To synchronize, ActiveSync version 3.7 or higher must be installed on both your desktop computer and the HT660e terminal. The HT660e terminal is installed with ActiveSync and shipped. Therefore, you must install ActiveSync 3.7 on your desktop computer. To install ActiveSync on your desktop computer, please link to Microsoft website to get free download driver. Installation Follow the installation procedure below to install Microsoft ActiveSync, connect your HT660e to your desktop computer, and establish a partnership for synchronization, if required. In order to exchange data between your computer and the HT660e, Microsoft ActiveSync must be installed on your computer. Use A USB cable that comes with your device or the docking station to connect the device to your computer. NOTE: If you have a previous version of the Microsoft ActiveSync installed in your computer, uninstall it first before installing the latest version of Microsoft ActiveSync. To install Microsoft ActiveSync on your computer: 1. Close any open programs, including those that run at startup, and disable any virus-scanning software. 2. Download the ActiveSync software from the Microsoft ActiveSync Download page at http://www.microsoft.com/downloads/details.aspx?Fami-lyID=7269173a-28bf-4cac-a682-58d3233efb4c&DisplayLang=en. 3. Browse to the location of the downloaded file, and double-click it. The installation wizard begins. 4. Follow the instructions on the screen to install Microsoft ActiveSync.

23 Connecting the Device to Your Computer 1. After ActiveSync has been installed, connect HT660e to your PC as described in Connecting the terminal to a host (PC/Notebook) to a PC. 2. Turn the HT660e on. 3. ActiveSync starts automatically and configure the USB port to work with the HT660e. The New Partnership setup wizard automatically starts. NOTE: If ActiveSync doesn’t start automatically, click Start → Programs → Microsoft ActiveSync. NOTE: If a message appears indicating that it is unable to detect a connection, click the Cancel button and manually configure the communication settings. 4. Follow the on-screen instructions. 5. When the configuration process is complete, the Active-Sync window appears. 6. Synchronization will be initialized and will take place if you’ve chosen to synchronize periodically or upon connection. NOTE: Your computer can create a partnership with multiple HT660es. Also, a HT660e can create a partnership with up to two computers.

24 WiFi Connection Unitech terminals come with built-in RF facility, Summit or Marvel. A wireless network can be added either when the network access point is detected or by manually entering setting data. Before following these instructions, make sure if authentication information is needed. Here, you can use, for example, the Summit Client Utility tool to do or change the WiFi settings. Admin Login 1. Tap Start → Programs → SUMMIT →scu. 2. To login as an administrator, tap Admin Login.

28 Using BTMAN to connect and pair a Bluetooth device After enabling the built-in Bluetooth module, you may use BTMAN to connect and pair a Bluetooth device around. BTMAN is a Bluetooth manager gathering and managing all Bluetooth profiles you add. Tap Start → Programs → Bluetooth → BTMAN to open the manager. In the Service tab, six icons, About, Power OFF/ON, FTP, ActiveSync, and Modem, are arranged. About: To show you the software version and BT module MAC address Power OFF/ON: To enable ON or OFF the BT module FTP: To transfer files to or receive files from a PC or terminal ActiveSync: To synchronize with a PC Modem: To allow you go on Internet after connecting to a cell phone as a modem

29 Power OFF/ON: To enable or disable paired Bluetooth earphones First of all, tap the Power OFF icon to enable the Bluetooth module. Tap Yes to turn ON the Bluetooth module. Tap the Scan Device tab to scan Bluetoothdevices around. Tap Scan Device.

30 Scanned Bluetooth devices around are listed. Later, you may double tap a desired device and check Trusted and then Active. ActiveSync Between HT660e and a PC or Terminal On the Scan Device tab, for example, select and double tap a desired PC. Tap Trusted. Tap Yes.

31 Enter a PIN code on the terminal and tap OK. Then, an Enter PIN dialog box pops up and enter the PIN code same as that you inputted on the terminal. Double tab the paired PC. When the pairing is successful, Trust and Active are checked. Move to the Service tab and tap ActiveSync. Tap Yes to launch ActiveSync. Then, HT660e will synchronize with the desired PC by means of Bluetooth.

33 receive data. Tap OK to confirm the connection. Choose a desired PC or terminal to or from which you want to transfer or Next, a dialog box pops up on the selected PC. Swhere a file or files may be transferred between HThe FTP Service zone appearelect and determine a path T660e and the PC. s. All function icons in the zone are defined below. Refresh Modem Y nternet by connecting HT660e to a mobile phone that serves as a modem. Follow the instruction below to connect and pa e with GPRS function. Tap the Scan Device tab to scan Bluetoothou may surf on Iir a mobile phondevices around. Shared Files List Upload Download End and Exit Move to subdirectoryMove to upper directory

34 Tap Scan Device. Scanned Bluetooth mobile phones around are listed. Later, you may double tap a desired phone and check Trusted and then Active.Then, HT660e is successfully connect to and paired with the phone as the modem.

$36 Chapter 5 Useful Utilities Introduction Unitech has been developing some of useful utilities for user’s application. The followings are Unitech Utilities introduction. Scanner Setting When it is necessary for the user to change the default barcode symbology for a different application, Scanner Control Panel provides the setting function to change default symbology, place delimiter characters behind scanned data, and save the settings. Run this program from \Start\Setting\Control Panel\Scanner Setting.exe and Scanner Control Panel will be displayed. Barcode Symbologies Barcode Symbology Enable/ Disable Char Check / Digit verificationTransmit Check Char/digit Leading Digit TransmitOthers Bookland EAN YES Codabar YES YES YES Transmit Start/Stop bits, CLSI format, *data length Code 11 YES YES * check digits, *data length Code 128 YES *data length Code 32 YES Transmit Tailing digit Code 39 YES YES For ASCII,$

37 Barcode Symbology Enable/ Disable Char Check / Digit verificationTransmit Check Char/digit Leading Digit TransmitOthers Transmit Start/Stop bits, Function Code, Double label decoding,*data length, *double labels separator Code 93 YES YES *data length Deta Code YES YES YES EAN 128 YES YES Transmit Code ID, * Field separator EAN 13 YES YES EAN 8 YES YES * Not suppress first or last digit, *data length Interleaved 2 of 5 YES YES YES Fixed Length, * Not suppress first or last digit, *data length Label Code IV&V YES YES MSI/Plessey YES YES * Check digit double module 10, * data length Interleaved 2 of 5 YES YES YES Fixed Length, *Data Length Telepen YES *Standard Character Set UPC A YES YES YES UPC E YES YES YES Zero Expension,NSC UPC/EAN Group Supplement 2, Supplement 5,Insert Space

38 Barcode Symbology Enable/ Disable Char Check / Digit verificationTransmit Check Char/digit Leading Digit TransmitOthers before supplement, most have supplement, *Add-on code try level Group GS1 YES Note: *Value Adjustable Scanner Control Pannel V3.0 Barcode Symbologies 2D Barcode Symbology Enable/ Disable Char Check / Digit verificationTransmit Check Char/digitLeading Digit TransmitOthers Aztec YES Runes, *data lengthCodablock F YES *data length Code 49 YES *data length Data Matrix YES *data length EAN-UCC Composite YES UPC composite, *data length MaxiCode YES *data length MicroPDF417 YES *data length OCR YES OCR mode, OCR direction, Template, Group G, Group H, Check character PDF-417 YES *data length QR Code YES TLC-39 (TCIF Linked Code 39) YES Note: *Value Adjustable Scanner Control Panel Version 5.14

$39 Scan2Key The Scan2Key application can route input from the scanner port to the keyboard buffer, with the result that all scanned data will be treated as if they were input from the keypad. With this router, scanned data can be directly input into generic applications like MS Pocket Word. Scan2Key can be found at: \Start\Setting\Control Panel\Scanner\To kpd.$

Unitech Electronics HT660EBTG PDA Scanner User Manual HT660e 400831G UM V10

Unitech Electronics Co., Ltd. PDA Scanner HT660e 400831G UM V10

User Manual

Navigation menu

Namespaces

Views

Navigation