Unitech Electronics MS912PBT Wireless Pocket CCD Scanner User Manual User Manuel
Unitech Electronics Co., Ltd. Wireless Pocket CCD Scanner User Manuel
User Manuel
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3189793 |
| Application ID | NvWt/tT1y8SIRQihtupuAg== |
| Document Description | User Manuel |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 115.42kB (1442782 bits) |
| Date Submitted | 2016-11-08 00:00:00 |
| Date Available | 2017-05-07 00:00:00 |
| Creation Date | 2016-09-07 14:49:39 |
| Producing Software | Acrobat Distiller 10.1.1 (Windows) |
| Document Lastmod | 2016-09-07 14:51:07 |
| Document Title | User Manuel |
| Document Creator | Acrobat PDFMaker 10.1 Word 版 |
| Document Author: | user |
掌上型無線 CCD 掃描器
- MS912+ -
使用手冊
Version 1.0
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd
前言
手冊介紹
感謝您選購 unitech 產品。
本手冊將介紹如何設定、操作及使用此項產品，包含基本設定介紹。
未經製造商書面許可，不得以任何形式、利用電子或機械手段(例如影印、錄音
或資訊儲存及擷取系統)重製或使用本刊物的任何部分。本手冊的內容如有變
更，恕不另行通知。
Regulatory Compliance Statements
FCC Warning Statements
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference with radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference with radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
1.
2.
3.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
This device complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. To maintain compliance with FCC RF
exposure requirements, avoid direct contact to the transmitting antenna
during transmitting.
Any changes or modifications (including the antennas) made to this device
that are not expressly approved by the manufacturer may void the user’s
authority to operate the equipment.
Operation on the 5.15 - 5.25GHz frequency band is restricted to indoor use
only. The FCC requires indoor use for the 5.15-5.25GHz band to reduce the
potential for harmful interference to co-channel Mobile Satellite Systems.
Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and
5.725–5.850 GHz band when associated with an access point (AP).
FCC Label Statement
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
RF Radiation Exposure Statement
For body contact during operation, this device has been tested and meets FCC
RF exposure guidelines when used with an accessory that contains no metal
and that positions the handset a minimum of 1.5 cm from the body.
Use of other accessories may not ensure compliance with FCC RF exposure
guidelines.
Canadian Compliance Statement
This Class B Digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement
sur le material broilleur du Canada.
ii
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
European Conformity Statement
unitech Electronics co., Ltd herewith declares that the unitech product is in
compliance with the essential requirements and all other provisions of the
R&TTE 1999/5/EC directive, the EMC 2004/108/EC directive and the Low
Voltage 2006/95/EC directive.
The declaration of conformity is available for download at :
https://portal.unitech.eu/public/Safetyregulatorystatement
RoHS Statement
This device conforms to RoHS (Restriction of
Hazardous Substances) European Union regulations
that set maximum concentration limits on hazardous
materials used in electrical and electronic
equipment.
Waste electrical and electronic equipment (WEEE)
unitech has set up a policy and process to meet the EU
directive 2002/96/EC and update 2003/108/EC
concerning electronic waste disposal.
For more detailed information of the electronic waste
disposal of the products you have purchased from
unitech directly or via unitech’s resellers, you shall either
contact your local supplier or visit us at :
https://portal.unitech.eu/public/WEEE
iii
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Taiwan NCC Warning Statement
交通部電信總局低功率電波輻射性電機管理辦法
第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者
均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有
干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備
之干擾。
注意事項:
1. 使用過度恐傷害視力。
2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過
1小時。
iv
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Laser Information
The unitech product is certified in the U.S. to conform to the requirements of
DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1.
Class II and Class 2 products are not considered to be hazardous. The unitech
product contains internally a Visible Laser Diode (VLD) whose emissions do
not exceed the maximum limits as set forth in the above regulations. The
scanner is designed so that there is no human access to harmful laser light
during normal operation, user maintenance or prescribed service operations.
The laser safety warning label required by the DHHS/IEC for the unitech
product’s optional laser scanner module is located on the memory
compartment cover, on the back of the unit.
* Laser information only applies to the products with laser components.
CAUTION! Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous laser
light. Use of optical instruments with the scanner, including
binoculars, microscopes, and magnifying glasses, with will
increase eye damage. This does not include eyeglasses worn by
the user.
LED Information
The unitech product contains LED indicator(s) or LED ring whose luminance is
not harmful to human eyes during normal operation, user maintenance or
prescribed service operations.
*LED information only applies to the products with LED components.
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Battery Notice
1.
To guarantee optimal performance, it is recommended that rechargeable
batteries be replaced every year, or after 500 charging cycles are
completed. It is normal for the battery to balloon or expand after one year
or 500 cycles. Although it does not cause damage, it cannot be used
again and must be disposed of according to the location's safe battery
disposal procedures.
2.
If a battery performance decreases more than 20%, the battery is at the
end of its life cycle. Stop use and ensure the battery is disposed of
properly.
3.
The length of time that a battery lasts depends on the battery type and
how the device is used. Conserve the battery life by doing the following:
Avoid fully uncharging the battery because this places additional
4.
5.
6.
7.
strain on it. Several partial uncharges with frequent charges are better
than a fully uncharged battery. Charging a partially charged battery
does not cause harm to the unit.
Keep the battery cool. Avoid hot vehicles. For prolonged
storage, keep the battery at a 40% charge level.
Do not leave the battery uncharged and unused for an extended
period of time, the battery will wear out and the longevity of the
battery will be at least half of one with frequent charges.
Protect battery life by not over or under charging the battery.
Please do not leave battery unused for long time without charging it.
Despite unitech’s safety precautions, the battery pack may begin to
change shape. If so, stop using it immediately. Please check to see if you
are using a proper power adapter to charge the battery or contact your
service provider for service.
If you cannot charge the battery after it has been idle for an extended
period of time and it begins to heat up, please do not try to charge it. It
may not be functional anymore.
Please only use the original battery from unitech. Using a third party
battery can damage our products. Please note that when such damage
occurs, it is not covered by unitech’s warranty policy
vi
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
CAUTION!
RISK OF EXPLOSION IF BATTERY IS
REPLACED INCORRECTLY.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS..
如果更換不正確之電池行事會有爆炸的風險
請依製造商說明書處理用過之電池
如果更换不正确之电池行事会有爆炸的风险
请依制造商说明书处理用过之电池
Battery charge notice
It is important to consider temperature when the battery pack is charging.
Charging is most efficient at normal room temperature or in a slightly cooler
environment. It is essential that batteries are charged within the stated range of
0°C to 40°C. Charging batteries outside of the specified range could damage
the batteries and shorten their life cycle.
CAUTION!
Do not charge batteries at a temperature lower than 0°C. This will
and make the batteries unstable and dangerous. Please use a
battery temperature detecting device for a charger to ensure a
safe charging temperature range.
Storage and safety notice
Although charged batteries may be left unused for several months, their
capacity may be depleted due to build up of internal resistance. If this happens,
they will require recharging prior to use. Batteries may be stored at
temperatures between -20°C to 60°C, however they may deplete more rapidly
at higher temperatures. It is recommended to store batteries at room
temperature.
* The message above only applies to the usage of the removable batteries.
For the products with non-removable batteries / without batteries, please refer to
the specification of each product.
Product Operation and Storage Notice
The unitech product has applicable operation and storage temperature
conditions. Please follow the limitation of suggested temperature conditions to
avoid failure, damage or malfunction.
*For applicable temperature conditions, please refer to the specification of each
product.
vii
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Adapter Notice
1.
2.
3.
4.
Please do not leave the power adapter in the socket when it is not
connected to your unitech product for charging.
Please remove the power adapter when the battery is fully recharged.
The bundled power adapter that comes with your unitech product is not
meant to be used outdoors. An adapter exposed to water or rain, or a very
humid environment can cause damage to both the adapter and the
product.
Please only use the bundled power adapter or same specification of
adapter to charge your unitech product. Using the wrong power adapter
can damage your unitech product.
* The message above only applies to the product connected to the adapter.
For the products without using the adapters, please refer to the specification of
each product.
Hearing Damage Warning
Zx.3 Warning
The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of
the following:
the symbol of Figure 1 with a minimum height of 5 mm; and
the following wording, or similar :
To prevent possible hearing damage, do not listen at high volume levels for long periods.
Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to
acknowledge activation of the higher level.
viii
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
全球支援
unitech’s professional support team is available to quickly answer questions or
assist with technical-related issues. Should an equipment problem occur,
please contact the nearest unitech regional service representative.
For complete contact information please visit the Web sites listed below:
Taipei, Taiwan – Headquarters
Europe
Tel:
+886-2-89121122
Tel:
+31-13-4609292
E-mail:
info@hq.ute.com
E-mail:
info@eu.ute.com
Address:
5F, No. 136, Lane 235, Baoqiao Road, Xindian
Address:
Tilburg, the Netherlands
District, New Taipei City 231, Taiwan (R.O.C.)
Website:
Kapitein Hatterasstraat 19, 5015 BB,
Website:
http://www.ute.com
China
http://eu.ute.com
Japan
Tel:
E-mail:
Address:
Website:
+86-59-2310-9966
info@cn.ute.com
Room401C, 4F, RIHUA International Mansion,
E-mail:
+81-3-35232766
E-mail:
info@jp.ute.com
Address:
Shinkawa, Chuo-Ku,
Xiamen, Fujan , China
Tokyo, 104-0033, Japan
http://cn.ute.com
Website:
http://jp.ute.com
Latin America
+886-2-27911556
Tel:
+52-55-5171-0528
info@apac.ute.com
E-mail:
info@latin.ute.com
info@india.ute.com
Address:
info@mideast.ute.com
Address:
Kayabacho Nagaoka Building 8F.,1-5-19
Xinfeng 3nd Road, Huoju Hi-tech District,
Asia & Pacific / Middle East
Tel:
Tel:
17171 Park Row, Suite 210
Houston, TX 77084USA (Rep.)
4F., No. 236, ShinHu 2nd Rd.,
Website:
http://latin.ute.com
NeiHu Chiu, 114, Taipei,Taiwan
Website:
http://apac.ute.com / http://mideast.ute.com
North America
Tel:
E-mail:
+1-714-8916400
info@us.ute.com / info@can.ute.com
Address:
6182 Katella Ave, Cypress, CA 90630, USA
Website:
http://us.ute.com
ix
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Warranty Policy
The items covered under the unitech Limited Warranty are free from defects
during normal use.
The warranty period is varied from each country. Please consult with your
supplier or unitech local office for actual length of warranty period to your
purchased product.
Warranty becomes void if equipment is modified, improperly installed or used,
damaged by accident or neglect, or if any parts are improperly installed or
replaced by the user.
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Table of Contents
前言...................................................................................................................i
手冊介紹........................................................................................................ i
Regulatory Compliance Statements .............................................................. i
Laser Information ......................................................................................... v
LED Information ........................................................................................... v
Battery Notice.............................................................................................. vi
Adapter Notice............................................................................................viii
Hearing Damage Warning ..........................................................................viii
全球支援...................................................................................................... ix
Warranty Policy ............................................................................................ x
第一章 –總覽 .................................................................................................1
1.1 產品配備清單..........................................................................................1
1.2 產品介紹 ................................................................................................2
1.3 規格 .......................................................................................................3
1.4 安裝與連線.............................................................................................5
1.5 電池充電 ................................................................................................5
1.6 掃描器LED和嗶聲說明 ...........................................................................6
第二章 – 安裝設定 ..........................................................................................7
2.1 BT HID....................................................................................................7
2.2 BT SPP.................................................................................................12
第三章 –條碼 .................................................................................................13
3.1 所有碼製 ..............................................................................................13
3.2 MSI / UK Plessey code.........................................................................16
3.3 Code93 / Telepen / IATA .......................................................................17
3.4 Interleaved 2 of 5 / Code 11 .................................................................18
3.5 Industrial 2 of 5 / Matrix 2 of 5 ..............................................................19
3.6 Codabar ...............................................................................................20
3.7 ABC Codabar, CX Codabar ..................................................................21
3.8 Code 39 (Full ASCII/Standard) / Code 32.............................................23
3.9 UPC-E ..................................................................................................24
3.10 UPC-E(0)&(1) / UPC-E EXPAND .......................................................25
3.11 UPC-A ................................................................................................26
3.12 EAN-8.................................................................................................27
xi
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
3.13 EAN-13 / ISSN / ISBN / ISMN ............................................................28
3.14 EAN & UCC128/Code 128 .................................................................30
3.15 DataBar (RSS) ...................................................................................31
第四章 – 偏好設定 ........................................................................................33
4.1 系統設定 ..............................................................................................33
4.2 BT Pairing.............................................................................................34
4.3 Output data transmit .............................................................................41
4.4 BT Config .............................................................................................46
4.5 Beep tone, Terminator ..........................................................................50
4.6 掃描模式 ..............................................................................................51
4.7 條碼長度設定,同步碼，後同步碼 .........................................................52
4.8 精確度調整...........................................................................................53
4.9 關機設定 ..............................................................................................54
附錄A – 數字條碼..........................................................................................55
附錄B – Full ASCII Table(Code39) ........................................................56
附錄C – 預設表 .............................................................................................67
xii
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
MS912+ 使用者手冊
第一章 –總覽
1.1 產品配備清單
請確認 MS912+包裝箱中各項配備是否齊全。
若發現任何組件遺失或損壞，請立即與 unitech 當地經銷商聯繫。
基本配件清單：
MS912+ 掃描器
快速指南
Regulatory Compliance Statements
USB 充電電源線
手帶
注意: 若想掃描條碼，請確認瞄準光束穿過條碼的每一條碼條及空隙。
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
MS912+ 使用者手冊
1.2 產品介紹
掃描鍵
LED 指示燈
Mini USB 連接埠
掃描視窗
硬體重設鍵
(將細長物插入洞中以重設 )
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
1.3 規格
效能/光學
影像感應器
線性 CMOS 感應器
光源
625 nm 可見紅色 LED
最大解析度
4 密耳(0.1mm)
掃描率
650 次掃描/秒
列印對比
最低 30%
掃描距離
讀取距離
(DOF PCS = 90%)
Code 39, 4mil: 40mm (近) / 65mm (遠)
Code 39, 5mil: 35mm (近) / 90mm (遠)
Code 39, 10mil: 35mm (近) / 195mm (遠)
Code 39, 15mil: 50mm (近) / 280mm (遠)
UPC/EAN, 13mil: 35mm (近) / 230mm (遠)
功能
碼制(Symbologies)
UPC-A/UPC-E, EAN-8/EAN-13, Industrial 2of 5,
Codabar, Matrix 2 of 5, Code 11, Code93, Code
32, Code 128, Standard Code 39,Full ASCII
Code 39, Interleaved 2 of 5, ChinaPostal Code,
MSI Plessy Code, UK PlessyCode, EAN/UCC
128, Telepen Code, IATACode, GS1 Databar.
組態方法
組態條碼
電器規格
操作電壓
3.7VDC ± 5%
電池類型
鋰電池
電流消耗
操作模式： < 145mA
待命模式： < 55mA
電池持續時間
6000 次讀取/充電
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
環境
ESD 保護
4KV Contact 和 8KV Air 後可運作
操作溫度
0°C 至 50°C
儲存溫度
-20°C 至 60°C
相對濕度
0% to 95% 非冷凝
掉落測試
1.5M
傳輸通訊
範圍
10M (無障礙)
支援的主控介面
Mini USB
介面/設定檔
SPP,HID
無線類別
無線第 2 類
機械規格
外殼材料
ABS + PC
尺寸
L65 x ABS + PC
18mm / 2.6 x 0.9 x 0.7in
重量
30.2g / 1.06oz
安規認證
FCC Part15B, FCC Part15C, EN301489-1-17, EN62133, EN60950-1,
EN300328, IEC 62471, NCC, TELEC, VCCI, BSMI
配件
Mini USB 連接線、手帶
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
1.4 安裝與連線
將掃描器連線至主控電腦(配對)
請確定您的電腦或智慧型手機具備一個內建的無線網路介面卡；MS912+支援
HID 及 SPP 無線設定檔。如果您是要連線至 iOS (Apple)的智慧型手機，請依照
「透過人機介面裝置(HID)模式連線」的說明執行；如果要連線至 Android 智慧
型手機，請依照「透過序列埠設定檔(SPP)模式連線」或「人機介面(HID)模式」
的說明執行。
注意：Android 2.x 裝置「只能」在 SPP 模式下和 MS912+搭配使用。SPP 模式及
/或 HID 模式並非與 Android 作業系統的每個版本完全相容，而取決於 Android
裝置製造商所定義之 Android 硬體規格。
1.5 電池充電
1.
2.
3.
翻轉開啟掃描器上的Mini USB連接埠。
將Mini USB接頭插入掃描器上的連接埠，然後將USB A接頭插入主控電腦上
的USB連接埠。
請將掃描器充電至少2個小時(直到LED指示燈熄滅為止)。
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
1.6 掃描器LED和嗶聲說明
掃描器 LED 和嗶聲說明
綠色 LED
紅色 LED
嗶聲
電源關閉或待命
充電中
恆亮
閃爍
閃爍
閃爍
1 次長嗶聲
1 次長嗶聲
閃爍
1 次嗶聲
1 次閃爍
1 次嗶聲
連線成功
2 次嗶聲
Pin 碼設定失敗
閃爍
低電量
閃爍
已中斷連線或可
以搜尋
正在初始化
開啟電源
掃描器
尚未正確連線的
條碼掃描
掃描條碼成功
備註
設定電源關閉逾時時間
3 次短嗶聲 掃描[Pin 碼停止]並重試
5 次嗶聲
4 次嗶聲
超出範圍
1 次閃爍
(高-低-高-
移動靠近主控裝置。
低)
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
第二章 – 安裝設定
2.1 BT HID
1.
2.
3.
開啟您主控裝置(個人電腦、智慧型手機或平板)上的無線裝置。
按下 MS912+掃描器的掃描鍵 1 秒鐘以啟動。
掃描[Disconnect]條碼。
Disconnect
4.
5.
按下 MS912+掃描器的掃描鍵 1 秒鐘以啟動。
掃描下方的[HID]條碼：
HID
6.
7.
8.
9.
掃描器會發出幾聲短促的嗶聲，然後停止。進行配對程序時，綠色的 LED
燈會持續閃爍。
在您的主控裝置上，位於可以看見藍牙設定和管理連線的設定區段中。
a. 您將在藍牙裝置看見列為[Wireless Scanner]的 MS912+。
b. 您將在[Pair with this device]看見一則訊息。
c. 在您的主機選擇此裝置，然後開始進行配對。
您的主控裝置會要求您輸入一組 Pin 碼。
a. 請使用您主控裝置的鍵盤輸入這組 Pin 碼。
b. 這組 Pin 碼可以是任何數字的組合。
c. 建議您使用 4 位數字。
當您在主控裝置中輸入 Pin 碼後，必須在 MS912+中設定 Pin 碼，才能進行
配對。
a. 請利用 MS912+掃描下方的 Pincode Start 條碼。
Pincode Start
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
b.
請參閱附錄 A 然後掃描與您主控裝置 Pin 碼相同的數字。例如：如果
您的 Pin 碼為「241657」，請依序掃描[2] - [4] - [1] - [6] - [5] - [7]：
c.
掃描下方的[Enter]條碼：
Enter
d.
掃描[Pincode-Stop]條碼：
Pincode-Stop
10. 在您的主控裝置中，您將在[Wireless Scanner]看見[連線中…]的訊息。
11. 當該訊息變成[已配對且已連線]時，掃描器將發出 2 次嗶聲證實連線成功，
接著您可以開始將條碼日期掃描至您的主控裝置。
a. 若要執行測試，請開啟 Word 或記事本，或一封新的電子郵件[可讓您輸
入資料的任何應用程式]。
b. 掃描本手冊中的數字條碼。
c. 該數字應該會出現在您主控裝置開啟的應用程式中。
d. 如果沒有出現，請掃描下方的[Disconnect]條碼，然後重複上述的步驟 1
到 9。
注意：若要將掃描器從主機中斷連線，或是切換為另一個無線設定檔，請掃
描[Disconnect]條碼：
Disconnect
掃描[Disconnect]條碼後，MS912+ 會發出 3 次嗶聲。
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
2.1.1 透過人機介面裝置(HID)模式連線(非Pin碼)
1. 按下 MS912+掃描器的掃描鍵 1 秒鐘以啟動。
2. 掃描[DISCONNECT]
Disconnect
3. 掃描[BT mode - HID non-pincode]；掃描器會發出 8 次嗶聲。
BT mode - HID non-pincode
4. 使用您主控電腦的藍牙模組搜尋附近的掃描器。
5. 按一下 Add a device 來搜尋附近的無線掃描器。
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
6. 按一下 Wireless Scanner，將其新增至電腦。接著請按一下 Next。
7. 在此步驟中，電腦會連線 Wireless scanner。連線時，請按一下 Next。
8. 按一下 Pair without using a code。接著請按一下 Next。
10
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
9. 接著請按一下 Close。
10. 您將看見一則訊息，顯示裝置驅動程式軟體已成功安裝。
11. 掃描器將發出 2 次嗶聲，證實已連線。
*注意：
在此模式下，主控裝置會將掃描器識別為滑鼠(指標裝置)。如果您的
主控裝置找不到掃描器，請嘗試[Connecting via Human Interface
Device (HID) Mode]。
11
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
2.2 BT SPP
1. 開啟您主控裝置(個人電腦、智慧型手機或平板)上的無線裝置。
2. 按下 MS912+掃描器的掃描鍵 1 秒鐘以啟動。
3. 掃描[Disconnect]條碼。
Disconnect
4. 掃描下方的 SPP 條碼:
SPP
5. 掃描器將發出多次嗶聲。
6. 請在您的主控裝置上搜尋 MS912+。從探索到的裝置清單中選擇「Wireless
Scanner」，掃描器將會發出 2 次嗶聲。
7. 輸入 Pin 碼(預設為「1234」)。
8. 開啟 COM 連接埠(已正確設定)的序列通訊軟體(請參閱裝置管理員)。
9. 掃描器將發出 2 次嗶聲，且 LED 指示燈將熄滅，證實已成功連線。
12
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
第三章 –條碼
3.1 所有碼製
啟動
取消
ENABLE ALL CODE
DISABLE ALL CDE
CODE 32
CODE 32 *
CHINA POSTAL CODE *
CHINA POSTAL CODE
UK PLESSEY CODE
UK PLESSEY CODE *
INDUSTRIAL 2 OF 5
INDUSTRIAL 2 OF 5 *
MATRIX 2 OF 5
MATRIX 2 OF 5 *
INTERLEAVED 2 OF 5 *
INTERLEAVED 2 OF 5
CODE 128 *
CODE 128
CODABAR *
CODABAR
TEELEPEN
TELEPEN *
13
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
啟動
取消
UPC-A *
UPC-A
UPC-E *
UPC-E
EAN-8 *
EAN-8
EAN-13 *
EAN-13
MSI
MSI *
CODE 39 *
CODE 39
CODE 11
CODE 11 *
CODE 93
CODE 93 *
EAN-128 *
EAN-128
IATA
IATA *
14
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
啟動
取消
GS1 Databar ENABLE
GS1 Databar DISABLE
GS1 Databar STACKED ENABLE *
GS1 Databar STACKED DISABLE
GS1 Databar LIMITED ENABLE
GS1 Databar LIMITED DISABLE *
GS1 Databar EXPANDED ENABLE
GS1 Databar EXPANDED DISABLE *
GS1 Databar EXPANDED STACKED
GS1 Databar EXPANDED STACKED
ENABLE *
DISABLE
PDF 417 ENABLE
PDF 417 DISABLE *
China postcode (Toshiba code)
ENABLE *
CDV & SEND CD
DISABLE
CDV & NOT SEND CD
DISABLE CDV *
MIN LENGTH (11)
MAX LENGTH (48)
15
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.2 MSI / UK Plessey code
MSI
UK PLESSEY CODE
ENABLE
ENABLE
DISABLE *
DISABLE
CDV & SEND CD*
CDV & SEND CD
CDV & NOT SEND CD
CDV & NOT SEND CD *
CHECK DIGIT DOUBLE MOD 10
CHECK DIGIT DOUBLE 11 PLUS MOD 10
CHECK DIGIT SINGLE MOD 10*
MIN LENGTH [6]
MAX LENGTH [48]
16
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.3 Code93 / Telepen / IATA
CODE 93
TELEPEN
IATA
ENABLE
ENABLE TELEPEN
ENABLE
DISABLE *
DISABLE TELEPEN*
DISABLE *
MIN LENGTH [6]
TELEPEN ASCII
DESABLE CDV *
MAX LENGTH [48]
TELEPEN NUMBER
CDV & SEND CD
CDV & NOT SEND CDV
MIN LENGTH [6]
MAX LENGTH [48]
17
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.4 Interleaved 2 of 5 / Code 11
INTERLEAVED 2 OF 5
CODE 11
ENABLE*
ENABLE
DISABLE
DISABLE*
DISABLE CDV*
DISABLE CDV *
CDV & SEND CD
CDV & SEND CD
CDV & NOT SEND CDV
CDV & SEND CDV (1DIGIT)
First digit suppressed
CDV & SEND CDV (2DIGIT)
Last digit suppressed
CDV & NOT SEND CD
NO suppressed *
MIN LENGTH [6]
MIN LENGTH [6]
MAX LENGTH [32]
MAX LENGTH [48]
18
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.5 Industrial 2 of 5 / Matrix 2 of 5
INTERLEAVED 2 OF 5
CODE 11
ENABLE
ENABLE
DISABLE*
DISABLE*
DISABLE CDV*
DISABLE CDV*
CDV & SEND CD
CDV & SEND CD
CDV & NOT SEND CDV
CDV & NOT SEND CDV
MIN LENGTH [6]
MIN LENGTH [6]
MAX LENGTH [48]
MAX LENGTH [48]
19
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.6 Codabar
CODEBAR
START / STOP
CLSI FORMAT
ENABLE *
ST/SP: abcd/abcd
DISABLE
ST/SP: ABCD/ABCD *
CLSI FORMAT ON
DESABLE CDV*
ST/SP:ABCD/TN*E
CLSI FORMAT OFF
CDV & SEND CD
ST/SP: abcd/tn*e
CDV & NOT SEND CD
SEND START / STOP *
MIN LENGTH [6]
Not Send START /STOP
MAX LENGTH [48]
20
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.7 ABC Codabar, CX Codabar
ABC- CODABAR
CX CODE- CODABAR
ON
ON
OFF*
OFF*
◆SET INSERT DATA
◆SET INSERT DATA
INSERT DATA-ON
INSERT DATA-ON
INSERT DATA-OFF
INSERT DATA-OFF
21
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.7.1 CODABAR COUPLING
CODABAR COUPLING
◆SET INSERT DATA
ON
OFF*
INSERT DATA-ON
INSERT DATA-OFF
ADJACENT REQUIRED
ON
OFF*
設定步驟
步驟 1 –
步驟 2 步驟 3 -
– SET INSERT DATA
掃描: Scan SET INSERT DATA.
掃描任一 FULL ASCII Table.請參考附錄 B
掃描 SET INSERT DATA.
RESET P023$
注意
1.
2.
如果掃描器發出 3 次嗶聲，其為設定更新未完成的警示。
如果您在嘗試更新掃描器設定時發生錯誤，例如不小心掃描到
錯誤的條碼，或是忘記操作步驟，請掃描上方的[RESET]條碼
重新開始掃描程序。
22
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.8 Code 39 (Full ASCII/Standard) /
Code 32
STANDARD CODE 39 & FULL ASCII 39
ENABLE *
DISABLE
FULL ASCII CODE39 ENABLE *
FULL ASCII CODE39 DISABLE
START / STOP –SEND
DESABLE CDV *
CDV & SEND CD
CDV & NOT SEND CD
MIN LENGTH [1]
MAX LENGTH [48]
START / STOP NOT SEND *
CODE 32
ENABLE
DISABLE *
LEADING SEND *
LEADING NOT SEND
TAILING SEND *
TAILING NOT SEND
23
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.9 UPC-E
UPC-E
ENABLE*
DISABLE
LEAD DIGIT SEND*
LEAD DIGIT NO SEND
CHECK DIGIT SEND*
CHECK DIGIT NO SEND
ADD ON SUPPLEMENT
+5 ON
+5 OFF*
+2 ON
+2 OFF*
ADD A SPACE ON
ADD A SPACE OFF*
ADDENDA REQUIRED ON
ADDENDA REQUIRED OFF
24
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.10 UPC-E(0)&(1) / UPC-E EXPAND
UPC-E0
E [0] OFF
E (0) ON *
E [1] ON
E (1) OFF *
UPC-E EXPAND TO UPC-A
ENABLE
DISABLE *
25
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.11 UPC-A
UPC-A
ENABLE *
DISABLE
LEAD DIGIT SEND *
LEAD DIGIT NO SEND
CHECK DIGIT SEND *
LEAD DIGIT NO SEND
UPC-A EXPANDTO EAN-13
ENABLE
DISABLE *
ADD ON SUPPLEMENT
+5 ON
+5 OFF *
+2 ON
+2 OFF *
ADD A SPACE ON
ADD A SPACE OFF *
ADDENDA REQUIRED ON
ADDENDA REQUIRED OFF
26
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.12 EAN-8
EAN-8
ENABLE*
DISABLE
LEAD DIGIT SEND*
LEAD DIGIT NO SEND
CHECK DIGIT SEND*
LEAD DIGIT NO SEND
ADD ON SUPPLEMENT
+5 ON
+5 OFF*
+2 ON
+2 OFF*
ADD A SPACE ON
ADD A SPACE OFF*
ADDENDA REQUIRED ON
ADDENDA REQUIRED OFF
27
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.13 EAN-13 / ISSN / ISBN / ISMN
EAN-13
ENABLE*
DISABLE
LEAD DIGIT SEND*
LEAD DIGIT NO SEND
CHECK DIGIT SEND*
CHECK DIGIT NO SEND
ADD ON SUPPLEMENT
+5 ON
+5 OFF*
+2 ON
+2 OFF*
ADD A SPACE ON
ADD A SPACE OFF*
ADDENDA REQUIRED ON
ADDENDA REQUIRED OFF*
28
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
ISBN
ISBN OFF*
ISBN ON
ISSN
ISSN OFF*
ISSN ON
ISMN
ISMN OFF*
ISMN ON
29
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.14 EAN & UCC128/Code 128
EAN / UCC-128
ENABLE*
DISABLE
CODE ID ENABLE
CODE ID DISABLE*
FUNC 1 CHAR SEND
FUNC 1 CHAR NOT SEND *
DEFINE EAN 128
String format：
設定步驟:
1: 掃描 DEFINE EAN128.
2: 掃描 ASCII Code 請參閱附錄 B
3: 掃描 DEFINE EAN128.
CODE 128
ENABLE*
DISABLE
MIN LENGTH [5]
MAX LENGTH [48]
30
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
3.15 DataBar (RSS)
GS1 DataBar (RSS) – OMNI & STACKED
GS1 DataBar ENABLE
GS1 DataBar DISABLE*
GS1 DataBar CHECK DIGIT SEND
GS1 DataBar CHECK DIGIT NOT SEND*
GS1 DataBar PREFIX SEND
GS1 DataBar PREFIX NOT SEND*
GS1 DataBar STACKED ENABLE *
GS1 DataBar STACKED DISABLE
GS1 Databar SET ID
GS1 DataBar (RSS) – LIMITED
GS1 DataBar LIMITED ENABLE
GS1 DataBar LIMITED DISABLE*
GS1 DataBar LIMITED CHECK DIGIT SEND
GS1 DataBar LIMITED CHECK DIGIT NOT
SEND*
GS1 DataBar LIMITED PREFIX SEND
GS1 DataBar LIMITED PREFIX NOT SEND *
GS1 DataBar LIMITED SET ID
31
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
GS1 DataBar (RSS) - EXPANDED
GS1 DataBar EXPANDED ENABLE
GS1 DataBar EXPANDED DISABLE*
GS1 DataBar EXPANDED STACKED ENABLE*
GS1 DataBar EXPANDED STACKED DISABLE
GS1 DataBar EXPANDED MIN LENGTH
GS1 DataBar EXPANDED MAX LENGTH
GS1 DataBar EXPANDED SET ID
32
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
第四章 – 偏好設定
4.1 系統設定
恢復原廠設定
◆Reset to factory default
檢查版本
◆Check firmware version
重設/ ABORT
◆Abort multi-step configuration
設定 CODE READ
SETUP CODE ON *
SETUP CODE OFF
33
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.2 BT Pairing
4.2.1 Interface
CODABAR COUPLING
Batch Mode
USB-HID
USB-VCP
MODE
WIRELESS
Interface
Auto Mode
BT HID
BT SPP
Batch Mode
Tethered
Batch Mode
Ez Utility
USB HID
USB VCP
34
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.2.2 藍牙連線
BT mode – HID
1. 按住trigger鍵維持1秒以啟動裝置。
2. 掃描 [DISCONNECT]
3. 掃描 [BT mode-HID]; 掃描器會發出幾聲嗶聲。
4. 請在您的主控裝置上搜尋MS912+。從探索到的裝置清單中選擇「Wireless
Scanner」， (PC裝置, 請選擇 “Create a pairing code for me”)
5. 藍牙應用程式將提示您輸入一組隨機Pin碼。
6. 請參考下一頁的 PINCODE SETUP
7. 掃描器將發出2次嗶聲，證實已連線成功。
BT mode - SPP
1. 按住trigger鍵維持1秒以啟動裝置。
2. 掃描 [DISCONNECT]
3. 掃描 [BT mode -SPP]; 掃描器會發出幾聲嗶聲。
4. 請在您的主控裝置上搜尋MS912+。從探索到的裝置清單中選擇「Wireless
Scanner」(PC裝置, 請選擇“Enter the device’s pairing code”)
5. 輸入Pin碼 ( 預設為「1234」)。
6. 開啟 COM 連接埠(已正確設定)的序列通訊軟體。
7. 掃描器將發出2次嗶聲，證實已連線成功。
BT mode - HID non-pincode
1. 按住trigger鍵維持1秒以啟動裝置。
2. 掃描 [DISCONNECT]
3. 掃描 [BT mode - HID non-pincode ]; 掃描器會發出幾聲嗶聲。
4. 請在您的主控裝置上搜尋MS912+。從探索到的裝置清單中選擇「Wireless
Scanner」，(PC裝置, 請選擇“Pair without using a code.)
5. 掃描器將發出2次嗶聲，證實已連線。
35
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
注意: 在此模式下，主控裝置會將掃描器識別為滑鼠(指標裝置)。如果您的主控
裝置找不到掃描器，請嘗試[BT mode -HID]。
Disconnect
4.2.2.1 Pincode 設定
STEP 1
Pincode Start
STEP 2 數字表 ( 請參閱附錄A)
STEP 3
Enter
STEP 4
Pincode Stop
36
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.2.2.2 連線至 iOS & Android
連線至 - iOS (Apple)
請參照 [BT mode - HID]. 因 Apple 裝置不需要 pincode 來連線，所以請忽略步
驟 5&6.
觸控式鍵盤
若要切換 iPhone/iPad 觸控式鍵盤，請掃描下方的條碼，或只要按兩下掃描鍵。
ENABLE iOS HOTKEY
DISABLE iOS HOTKEY
37
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.2.2.3 設定藍牙裝置ID
若要為無線掃描器自訂您的藍牙裝置(MS912+)名稱，請依照下列步驟執行
步驟 1 掃描 Default Wireless ID 條碼
步驟 2 掃描 Set Wireless ID 條碼
步驟 3 掃描附錄 B Full ASCII Chart中的英數字元。
步驟 4
掃描設定無線 ID 條碼
步驟 5
掃描所需的BT模式條碼(SPP或HID)以執行連線。
*注意：
1.
如果您在自訂您的藍牙裝置名稱「之前」，就已經透過主控裝置連線掃描器，請移除該裝
置並建立一個新的連線，以確定裝置名稱已重新整理。若主控裝置為電腦，建議您重新啟
動藍牙介面卡，以重新整理裝置名稱。
2.
在步驟 3 中，如果輸入超過 7 個字元，掃描器將發出 3 次嗶聲做為警示。
38
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.2.2.4 Set Pincode
By default, the pincode under SPP profile for eh scanner is “1234” You may
customize this pincode with bellows steps:
STEP 1
Set SPP Pincode
STEP 2 Scan numeric barcodes (see Appendix A) Up to 8 numbers can
be set as SPP pincode
STEP 3
Set SPP Pincode
STEP 4 Scan a desired BT mode in BLUETOOTH PROFILE(4.2.2) to
Complete the configuration.
4.2.2.5 SPP Master Mode
First, please generate one configuration barcode for the target SPP slave
device in below methods:
1. The barcode must be Code 39 with no checksum
2. Barcode data format: LTB + Target MAC address
For example, the target SPP slave device’s MAC address is 001583522C3B.
Please encode:
*LTB001583522C3B* in Code39 barcode.
Then, follow below steps to create connection:
STEP 1
SPP-Master
STEP 2
39
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.2.2.6 Remote Control
SPP REMOTE CONTROL
There are two ways to verify connection status by the host under SPP Profile.
Command Response
Host sends:
Scanner replys:
CR,LF,{,A,L,},CR,LF
O,K,CR,LF
(8 bytes)
(4 bytes)
CR,LF,{,M,1,},CR,LF
a short beep
(8 bytes)
Beeper Response
Host sends:
Scanner replys:
SHUT DOWN
This configuration barcode will shut down the scanner immediately but still
reserve the pairing record.
SHUT DOWN
DISCONNECTION
DISCONNECT
(CLEAR PAIRING RECORD)
DISCONNECT
(KEEP PAIRING RECORD)
40
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.3 Output data transmit
4.3.1 Auto mode
Auto mode
ENABLE
DISABLE
When out of range, the scanner will temporarily keep scanned data in its
memory buffer (2K RAM) until the buffer is full. When back in range, the
scanner will send all stored data back to the host.
NOTE: Auto mode will not function when Batch Mode is enabled, or no
connection is made beforehand.
BINARY CHECK CHARACTER
ENABLE
DISABLE
Once enabled, a checksum will be added to the end of each data to conduct
Xor calculation. For Bluetooth SPP & USB-VCP, the BCC is 1 byte. For
Bluetooth HID, the BCC are 2 bytes.
Example:
The barcode data is “TEST” with terminator
1. Bluetooth SPP & USB-VCP:
Data Format = + + + + + + . BCC =
54h ^ 45h ^ 53h ^ 54h ^ 0Dh ^ 0Ah = 11h
2. Bluetooth HID:
Data Format = + + + + + BCC = 54h ^
45h ^ 53h ^ 54h ^ E7h = F1h
However, since control character cannot be displayed in Bluetooth HID, BCC
will be converted into 2 bytes of characters.
As a result, the data will be: TEST + + F + 1
41
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.3.2 Batch mode
Batch mode
After scanning the above barcode, the scanner will be able to collect barcode
data off-line. The barcode data will be stored in the format of:
< Date >, < Time >, < Barcode Data > < CR >
To retrieve stored data, please connect the scanner to the host with cable,
access removable storage device “MiniScan” from which you may open or
copy the file “BARCODE.txt” to your computer.
To delete ONE stored data, please scan below barcode :
DELETE LAST DATA
To delete ALL stored data, simply delete the file “BARCODE.txt” in the
removable storage device “MiniScan” until you hear two beeps.
42
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.3.2.1 Batch mode - Data Format /
Date & Time Setup
DATA FORMAT
注意：[僅支搜記憶體版本]
預設的資料格式為<日期>、<時間>，下方的<條碼資料>為項目及其設定代碼：
代碼
項
日期
時間
條碼資料
例如：
若要將資料格式變更為<條碼資料>、<日期>、<時間>
1. 請掃描[Date Format]
2. 掃描第[4], [2], [3]，請參閱附錄 A
3. 請掃描[Date Format]
FIELD SEPARATOR
預設為逗號( , )。您可以利用使用手冊完整 ASCII 表中的任何英數字元來取代此
符號。
例如：將欄位分隔符號變更為分號( ; )
1. 掃描[Field Separator]
2. 掃描完整 ASCII 表中的[ ; ]。
3. 掃描[Field Separator]
43
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
日期時間設定
日期設定
注意：[僅支搜記憶體版本]
例如：若要將日期設定為 2012-08-01 (年-月-日)：
1. 掃描[Set Date]
2. 請參閱附錄 A 的[1]、[2]、[0]、[8]、[0]、[1]。
3. 掃描[Set Date]
時間設定
例如：若要將時間設定為 08:10:30 am (小時：分鐘：秒)
1. 掃描[Set Date]
2. 請參閱附錄 A 的[0]、[8]、[1]、[0]、[3]、[0]。
3. 掃描[Set Date]
* 若要避免電池電力用盡導致時間與日期重設為原廠預設值，請在使用前
至少充電3個小時，以充飽掃描器的電力。
44
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
DATE FORMAT
注意：[僅支搜記憶體版本]
預設的日期格式為 DD/MM/YYYY (Code = 09)，以下是可用格式及其設定代碼的
完整清單：
代碼
01
02
03
04
05
06
07
08
項目
DD-MM-YYYY
MM-DD-YYYY
DD-MM-YY
MM-DD-YY
YYYY-MM-DD
YY-MM-DD
DD-MM
MM-DD
代碼
09
10
11
12
13
14
15
16
項目
DD/MM/YYYY
MM/DD/YYYY
DD/MM/YY
MM/DD/YY
YYYY/MM/DD
YY/MM/DD
DD/MM
MM/DD
例如：
若要將日期格式設定為 MM/DD/YY (Code = 12)
1. 掃描[Date Format]
2. 請參閱附錄 A 的[1]、[2]。
3. 掃描[Date Format]
TIME FORMAT
注意：[僅支搜記憶體版本]
預設的 Time Format 為 HH:MM:SS (Code = 01)，以下是可用的格式及其設定代碼：
代碼
項目
代碼
01
HH:MM:SS
02
例如：
若要將時間格式設定為 HH:MM (Code = 02)
1. 掃描[Time Format]
2. 請參閱附錄 A 的[0]、[2]。
3. 掃描[Time Format]
項目
HH:MM
45
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.4 BT Config
4.4.1 Inter-block and Inter-character Delay
INTERBLOCK DELAY
INTERCHARACTER DELAY
0mS
140uS
10mS
500uS
50mS
1mS
100mS
4mS
200mS
16mS
500mS
46
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.4.2 Caplock Mode / Numeric Key
INTERBLOCK DELAY
INTERCHARACTER DELAY
CAPLOCK ON
NUMERIC KEY
CAPLOCK OFF *
ALPHANUMERIC KEY *
CAPLOCK FREE
47
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.4.3 KEYBOARD LAYOUT
KEYBOARD LAYOUT
ENGLISH (USA) *
SWISS (GERMAN)
ENGLISH (UK)
SWISS (FRENCH)
FRENCH
JAPAN (106KEY)
GERMAN
CANDIAN (FRENCH)
ITALIAN
CANADIAN (TRADITIONAL)
SPANISH
NORWEGIAN
CZECH (QWERTY)
SWEDISH
CZECH (QWERTZ)
PORTUGUESE
HUNGARIAN (QWERTZ)
BELGIAN (AZERTY)
48
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
KEYBOARD LAYOUT
HUNGARIAN (101 KEY)
DUTCH
DANISH
BRAZILIAN (PORTUGUESE)
SLOVAK
ALT CODE
49
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.5 Beep tone, Terminator
BEEP TONE
TERMINATOR
2.7KHz Buzzer
BEEP OFF
NONE
BEEP HIGH
LF
BEEP HIGH-LOW
CR *
BEEP MEDIUM *
CR+LF *
BEEP LOW-HIGH
TAB
BEEP LOW
SPACE
ESC
50
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.6 掃描模式
4.6.1 Trigger mode *
4.6.2 Continuous mode
4.6.3 Continuous Auto off
4.6.4 Flash mode
4.6.5 Toggle mode
51
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.7 條碼長度設定,同步碼，後同步碼
條碼長度設定
同步碼(字首)和後同步碼(字尾)：
SEND DATA LENGTH ON
CLEAR PRE / POSTAMBLE
SEND DATA LENHTH OFF *
PREAMBLE (16)
POSTAMBLE (16)
例如：
將同步碼字串設定為「##」
後同步碼字串設定為「$$」
設定程序：
步驟1：掃描：CLEAR PRE/ POSTAMBLE
步驟2：掃描：PREAMBLE.
步驟 3：附錄 B 完整 ASCII 表中的「#」兩次。
步驟 4：掃描：PREAMBLE.
步驟 5：掃描：POSTAMBLE.
步驟 6：掃描：附錄 B 完整 ASCII 表中的「$」兩次。
步驟7：掃描：後同步碼。
DATA FORMAT:
[Preamble] [Symbology ID] [Barcode Length] [Barcode Data] [Postamble]
[Terminator]
格式：
{Preamble} {Code ID}{Bar Code }{Postamble}
注意：
1.
同步碼是一個多達 16 個字元的字串，會新增至掃描條碼的開頭。
2.
後同步碼是一個多達 16 個字元的字串，會新增至掃描條碼的
結尾。
兩者的預設值：無。
3.
52
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.8 精確度調整
精確度調整
精確度調整可確保解碼輸出更為可靠。啟用此功能並設定 1 到 9 的數字，可以提高解碼輸
出的精確度標準。數字越大，精確度越高。
步驟 1 掃描精確度調整。
步驟 2 從附錄 A 中掃描一個數元(1 到 9)。
步驟 3 掃描精確度調整
RESET
P023$
注意：
1. 掃描器將發出 3 次嗶聲，提醒設定尚未完成。
2. 如果設定發生錯誤，或是忘記設定步驟等，請掃描 RESET 即可再次開始。
53
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
4.9 關機設定
時間設定 (預設值: 3分鐘)
分鐘設定 (範圍: 00 ~ 60)
秒數設定 (範圍: 00 ~ 60)
例子: 設定5分鐘30秒關機
1. 掃描 [Set Minute]
2.
3.
4.
5.
6.
掃描 [0] & [5] ，請參閱附錄A
掃描[Set Minute]
掃描[Set Second]
掃描 [3] & [0] ，請參閱附錄A
掃描[Set Second]
取消關機 ( 維持待機 )
DISABLE TIMEOUT
54
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
附錄 A – 數字條碼
FULL ASCII ( Code 39 ) NUMERIC TABLE
最小/最大長度
設定程序
步驟 1－掃描：最小/最大長度
步驟 2－掃描：附錄中的兩個數元
步驟 3－掃描：最小/最大長度
請注意，如果已啟用最小長度及/或最大長度，掃描器將只讀取條碼長度符合這些
長度參數的條碼。掃描器將不會讀取比指定長度更短或更長的條碼。其預設長度
位於每個碼制最小和最大條碼的括號內。
RESET
P023$
備註:
1. 若聽到嗶聲三聲，則表示設定未完成。
2. 若想重新設定，請掃上方條碼 RESET 以重新開始。.
55
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
附錄 B – Full ASCII Table(Code39)
CONTROL CODES
56
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
CONTROL CODES
57
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
SYMBOLS
58
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
SYMBOLS
59
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
UPPER CASE ALPHABETS
60
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
UPPER CASE ALPHABETS
61
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
LOWER CASE ALPHABETS
62
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
LOWER CASE ALPHABETS
63
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
FUNCTION KEYS FOR PC-AT
64
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
NAVIGATION KEYS
65
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
MODIFIER KEYS
注意：
*1.
已設定「Alt(left)Make」。請掃描「Alt(left)Break」繼續設定條碼。
*2.
已設定「Shift(left)Make」。請掃描「Shift(left)Break」繼續設定條碼。
*3.
已設定「Ctrl(left)Make」。請掃描「Ctrl(left)Break」繼續設定條碼。
66
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
附錄 C – 預設表
67
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
68
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
69
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
70
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
71
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
72
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
MS912+ 使用者手冊
73
© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Author : user Create Date : 2016:09:07 14:49:39+08:00 Modify Date : 2016:09:07 14:51:07+08:00 Subject : XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : Acrobat PDFMaker 10.1 Word 版 Metadata Date : 2016:09:07 14:51:07+08:00 Producer : Acrobat Distiller 10.1.1 (Windows) Keywords : Format : application/pdf Creator : user Title : Description : Document ID : uuid:8794f528-a876-4ad5-a743-8a8108afa83f Instance ID : uuid:fe0e1341-55f5-4a88-9c11-eb9b28954e88 Company : Unitech Comments : Page Layout : OneColumn Page Count : 86EXIF Metadata provided by EXIF.tools