Unitech Electronics MS926BT BT Barcode Scanner User Manual

Unitech Electronics Co., Ltd. BT Barcode Scanner Users Manual

UserManual.wiki >

Unitech Electronics >

MS926BT User Manual

Users Manual

i © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual Preface About This Manual Thank you for purchasing the unitech product. This manual explains how to install, operate and maintain our product. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, such as photocopying, recording, or information storage and retrieval systems, without permission in writing from the manufacturer. The material in this manual is subject to change without notice. Regulatory Compliance Statements FCC Warning Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help. 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF

ii © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual exposure requirements, avoid direct contact to the transmitting antenna during transmitting. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. FCC Label Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. RF Radiation Exposure Statement For body contact during operation, this device has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of 1.5 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Canadian Compliance Statement This Class B Digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. European Conformity Statement unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the

iii © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual R&TTE 1999/5/EC directive, the EMC 2004/108/EC directive and the Low Voltage 2006/95/EC directive. The declaration of conformity is available for download at : https://portal.unitech.eu/public/Safetyregulatorystatement RoHS Statement This device conforms to RoHS (Restriction of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. Waste electrical and electronic equipment (WEEE) unitech has set up a policy and process to meet the EU directive 2002/96/EC and update 2003/108/EC concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitech’s resellers, you shall either contact your local supplier or visit us at : https://portal.unitech.eu/public/WEEE

iv © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual Taiwan NCC Warning Statement 交通部電信總局低功率電波輻射性電機管理辦法第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。注意事項: 1. 使用過度恐傷害視力。 2. 使用30分鐘請休息10分鐘；2歲以下幼兒不看螢幕，2歲以上每天看螢幕不要超過 1小時。 3. 減少電磁波影響，請妥適使用。

v © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual Laser Information The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or prescribed service operations. The laser safety warning label required by the DHHS/IEC for the unitech product’s optional laser scanner module is located on the memory compartment cover, on the back of the unit. * Laser information only applies to the products with laser components. CAUTION! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner, including binoculars, microscopes, and magnifying glasses, with will increase eye damage. This does not include eyeglasses worn by the user. LED Information The unitech product contains LED indicator(s) or LED ring whose luminance is not harmful to human eyes during normal operation, user maintenance or prescribed service operations. *LED information only applies to the products with LED components.

vi © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual Battery Notice 1. To guarantee optimal performance, it is recommended that rechargeable batteries be replaced every year, or after 500 charging cycles are completed. It is normal for the battery to balloon or expand after one year or 500 cycles. Although it does not cause damage, it cannot be used again and must be disposed of according to the location's safe battery disposal procedures. 2. If a battery performance decreases more than 20%, the battery is at the end of its life cycle. Stop use and ensure the battery is disposed of properly. 3. The length of time that a battery lasts depends on the battery type and how the device is used. Conserve the battery life by doing the following:  Avoid fully uncharging the battery because this places additional strain on it. Several partial uncharges with frequent charges are better than a fully uncharged battery. Charging a partially charged battery does not cause harm to the unit.  Keep the battery cool. Avoid hot vehicles. For prolonged storage, keep the battery at a 40% charge level.  Do not leave the battery uncharged and unused for an extended period of time, the battery will wear out and the longevity of the battery will be at least half of one with frequent charges. 4. Protect battery life by not over or under charging the battery. 5. Please do not leave battery unused for long time without charging it. Despite unitech’s safety precautions, the battery pack may begin to change shape. If so, stop using it immediately. Please check to see if you are using a proper power adapter to charge the battery or contact your service provider for service. 6. If you cannot charge the battery after it has been idle for an extended period of time and it begins to heat up, please do not try to charge it. It may not be functional anymore. 7. Please only use the original battery from unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by your warranty.

vii © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual  RISK OF EXPLOSION IF BATTERY IS REPLACED INCORRECTLY. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.  如果更換不正確之電池行事會有爆炸的風險請依製造商說明書處理用過之電池 CAUTION!  如果更换不正确之电池行事会有爆炸的风险请依制造商说明书处理用过之电池 Battery charge notice It is important to consider temperature when the battery pack is charging. Charging is most efficient at normal room temperature or in a slightly cooler environment. It is essential that batteries are charged within the stated range of 0°C to 40°C. Charging batteries outside of the specified range could damage the batteries and shorten their life cycle. CAUTION! Do not charge batteries at a temperature lower than 0°C. This will and make the batteries unstable and dangerous. Please use a battery temperature detecting device for a charger to ensure a safe charging temperature range. Storage and safety notice Although charged batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens, they will require recharging prior to use. Batteries may be stored at temperatures between -20°C to 60°C, however they may deplete more rapidly at higher temperatures. It is recommended to store batteries at room temperature. * The message above only applies to the usage of the removable batteries. For the products with non-removable batteries / without batteries, please refer to the specification of each product. Product Operation and Storage Notice The unitech product has applicable operation and storage temperature conditions. Please follow the limitation of suggested temperature conditions to avoid failure, damage or malfunction. *For applicable temperature conditions, please refer to the specification of each product.

viii © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual Adapter Notice 1. Please do not leave the power adapter in the socket when it is not connected to your unitech product for charging. 2. Please remove the power adapter when the battery is fully recharged. 3. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product. 4. Please only use the bundled power adapter or same specification of adapter to charge your unitech product. Using the wrong power adapter can damage your unitech product. * The message above only applies to the product connected to the adapter. For the products without using the adapters, please refer to the specification of each product. Hearing Damage Warning Zx.3 Warning The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following: - the symbol of Figure 1 with a minimum height of 5 mm; and - the following wording, or similar : To prevent possible hearing damage, do not listen at high volume levels for long periods. Alternatively, the entire warning may be given through the equipment display during use, when the user is asked to acknowledge activation of the higher level.

ix © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual Worldwide Support unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan – Headquarters Europe Tel: +886-2-89121122 Tel: +31-13-4609292 E-mail: info@hq.ute.com E-mail: info@eu.ute.com Address: 5F, No. 136, Lane 235, Baoqiao Road, Xindian District, New Taipei City 231, Taiwan (R.O.C.) Website: http://www.ute.com Address:Website:Kapitein Hatterasstraat 19, 5015 BB, Tilburg, the Netherlands http://eu.ute.com China Japan Tel: +86-59-2310-9966 Tel: +81-3-35232766 E-mail: info@cn.ute.com E-mail: info@jp.ute.com Address: Website: Room401C, 4F, RIHUA International Mansion, Xinfeng 3nd Road, Huoju Hi-tech District, Xiamen, Fujan , China http://cn.ute.com Address:Website:Kayabacho Nagaoka Building 8F.,1-5-19 Shinkawa, Chuo-Ku, Tokyo, 104-0033, Japan http://jp.ute.com Asia & Pacific / Middle East Latin America Tel: +886-2-27911556 Tel: +52-55-5171-0528 E-mail: info@apac.ute.com info@india.ute.com info@mideast.ute.com E-mail:Address:info@latin.ute.com 17171 Park Row, Suite 210 Houston, TX 77084USA (Rep.) Address: 4F., No. 236, ShinHu 2nd Rd., NeiHu Chiu, 114, Taipei,Taiwan Website: http://latin.ute.com Website: http://apac.ute.com / http://mideast.ute.com North America Please scan QR Code to visit us : Tel: +1-714-8926400 E-mail: Address: Website: info@us.ute.com / info@can.ute.com 6182 Katella Ave, Cypress, CA 90630, USA http://us.ute.com

x © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual Warranty Policy The items covered under the unitech Limited Warranty are free from defects during normal use. The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.

xi © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual Table of Contents Preface...........................................................................................................i About This Manual ........................................................................................i Regulatory Compliance Statements ..............................................................i Laser Information .........................................................................................v LED Information ...........................................................................................v Battery Notice.............................................................................................. vi Adapter Notice............................................................................................viii Hearing Damage Warning ..........................................................................viii Worldwide Support ...................................................................................... ix Warranty Policy ............................................................................................x Chapter 1 - Overview................................................................................1 1.1 Package .................................................................................................1 1.2 Scanner Detail........................................................................................2 1.3 Specifications .........................................................................................3 1.4 Getting Started .......................................................................................6 1.5 Battery Charging ....................................................................................7 1.6 LED Indicator / Beeper Sequence..........................................................8 1.7 Display Menu Tree .................................................................................9 Chapter 2 - Installation..........................................................................19 2.1 NFC Pairing with Mobile Devices .........................................................19 2.2 BT HID..................................................................................................19 2.3 BT SPP.................................................................................................20 2.4 BT SPP (Slave) ....................................................................................21 2.5 USB SPP..............................................................................................22 Chapter 3 – Symbology ..........................................................................23 3.1 All symbologies.....................................................................................23 3.2 Message Length Description................................................................23 3.3 1D.........................................................................................................24 3.4 2D.........................................................................................................61

xii © 2015 unitech Electronics Co., Ltd. All rights reserved. unitech is a registered trademark of unitech Electronics Co., Ltd. MS926 User’s Manual Chapter 4 – Command Settings...........................................................66 4.1 System setting......................................................................................66 4.2 BT pairing .............................................................................................68 4.3 Output data transmit.............................................................................69 4.4 BT Config .............................................................................................72 4.5 Beep & Vibration ..................................................................................75 4.6 Scan mode / Parameter Selection........................................................77 4.7 Prefix/Suffix selections .........................................................................89 4.8 Data formatting.....................................................................................93 4.9 Data Validation ................................................................................... 114 4.10 Lookup Table Function ..................................................................... 115 4.11 Manually set up................................................................................. 116 Appendix A – Symbology Charts.......................................................119 Appendix B – Programming Charts..................................................124

- 1 - MS926 User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the MS926 gift box. If something is missing or damaged, please contact your unitech representative. The standard package contents MS926 Scanner Quick Reference Guide Micro USB to USB Cable Hand Strap Optional accessories 1-Slot Charging cradle 5-Slot Charging cradle USB Adapter NOTE: 1. The scanner’s default power off time is 5 minutes. 2. Please charge scanner for at least 2 hours prior to initial use. 3. The barcode with an asterisk (*) which appears in the following chapters indicates that it is the default option for the corresponding setting.

- 2 - MS926 User’s Manual 1.2 Scanner Detail Micro USB Connector For scanner charging and data transmission Screen Show the information on the screen Scan Window Scan & Power Button Power On/Off & Scan barcode Charging Status LED (Red LED) It will light up while the scanner is charging Scan LED (Green LED) It will light up while the barcode is successfully scanned Page up / Page down keys (on the side of MS926) Move up / down through list of menu items Product Label NFC Pairing Label Hand Strap Hole Reset Key press one time: power off

- 3 - MS926 User’s Manual 1.3 Specifications System Display 1" OLED, 128 x 64 OS Proprietary, Connect to host with Windows, Android and iOS Memory 64 Kbytes SRAM / 2 MB Flash ROM Key 3 Keys: Page Up, Page Down, Scan with power on/off feature Optical & Performance Receiving Device CMOS sensor with 640 x 480 pixel resolution Illumination & Aiming White LED illumination; Red LED dot aimer Motion Tolerance Up to 100 cm/s (4 in/s) for13 mil UPC at optimal focus Typical frame rate 30 frames per second Skew Angle ±45 Pitch Angle ±45 Printing Contrast Scale 35% minimum print contrast ratio Depth of Field (DOF PCS=80%)

- 4 - MS926 User’s Manual Functionality Symbologies 1D Code UPC-A, UPC-E, EAN-8, EAN-13, CODE 39, CODE 128, GS1 128 , I 2 of 5, NEC 2 of 5, CODE 93, Codabar, GS1DataBar Omn, GS1DataBar Ltd, GS1DataBar Exp, CODE 11, MSI, UPC-E1, S 2 of 5 Indus, S 2 of 5 IATA, Matrix 2 of 5 1D Postal Code China Post, Korea Post 2D Code QR Code, Data Matrix, Aztec Code, PDF417, Macro PDF417, Micro PDF417, MaxiCode, Codablock A, Codablock F, GS1 Composite, Han Xin Code 2D Postal Code Australian Post, British Post, Canadian Pos, InfoMail, Intelligent Mail Bar Code, Japanese Post, KIX (Netherlands) Post, GS1 Composite, Korea Post, Planet Code, Postal, Postnet Scan Mode Trigger mode, Pulse mode, Flash mode, Continuous Mode, Buffer mode Environmental ESD Protection Functional after 8K Contact and 12K Air Mechanical Shock 1.5m onto concrete (scanner only) IP Rate IP42 Operating Temperature 0°C to 50°C Storage Temperature -30°C to 70°C Relative Humidity 95% non-condensing Electrical Operation Voltage DC 3V to 5V Current Consumption Operation mode: 400mAh, Standby mode: 160mAh Battery Type Rechargeable Li-ion battery Battery Capacity 680 mAh Battery Charging time Fully charged in about 4 hours Operating Time 5 hours at condition of 1 scan/5 sec

- 5 - MS926 User’s Manual Communication Radio Frequency BT V2.1+EDR. Class 2 Protocol Wireless SPP & HID profiles Range Up to 30 Feet (Open space) Interface supported Micro USB Mechanical Scanner Dimension H21.1*W36.9*L95.9mm Scanner Weight 63g Switch life 10 million times Regulation Approvals CE, FCC, BSMI, VCCI

- 6 - MS926 User’s Manual 1.4 Getting Started To turn on the scanner, press and hold the Scan & Power Button for about 2 seconds. To turn off the scanner, press and hold the Scan & Power Button for about 5 seconds. After powering on, you will see the following screen on the scanner display. The scanner is now under standby mode. Now you can scan the desired barcode. The standby display will show the current Battery Status, Scanner Type, Operation Mode, and Time. To scan a barcode, make sure the aiming beam crosses every bar and space of the barcode.

- 7 - MS926 User’s Manual 1.5 Battery Charging Insert the Micro USB connector into the port on the scanner and the standard USB connector of the USB cable into a USB port on the host PC.

- 8 - MS926 User’s Manual 1.6 LED Indicator / Beeper Sequence Division Action/Status LED for Barcode reading & CommunicationLED for Battery status Beep / Sound Power On Green & Red Lights blink once One High Beep Auto Power Off Long press trigger key for 5 seconds Three short beeps at 15 seconds before power off USB connection Low- Medium –High Beeps USB disconnection High- Medium –LowBeeps Wedge & Auto (When BT Connect) Green Light blinks once One Beep Batch Green Light blinks once One short Beep Barcode reading Wedge & Auto (When BT Disconnect) Green Light blinks once One short Beep Data sent to PC successfully (Batch) Green Light blinks once Dee-Du sound Data sent to PC Fail sent data to PC (Batch) Red Light blinks once Dee-Dee-Dee sound Data delete Green Light blinks once All Data delete Deleting- Green light always on BT connection Low- Medium –HighBeeps BT disconnection High- Medium –LowBeeps Low Battery Alarm (<10%) (USB charging cable disconnected) Blinking Red Light Battery charging (USB charging cable connected) Red light always on Battery Fully charged (USB charging cable connected) Green light always on

- 9 - MS926 User’s Manual 1.7 Display Menu Tree To enter main menu of MS926, press and hold Page Down button and then press Page Up button. You will see the following screen on the MS926 display. Now you can use Page Up/Down button to scroll through the menu and use Scan button to make your selection. The Display Menu Tree below is based on Auto Mode. Top Menu Sub Menu Level 1 Sub Menu Level 2/Options/Result Options/Result Default Setting 1.1 BT HID 1.2 USB SPP 1.3 BT SPP 1. Scanner Type 1.4 BT SPP (Slave) n/a BT HID 2.1 Wedge Mode 2.2 Batch Mode 2. Operation Mode 2.3 Auto Mode n/a Auto Mode 3.1 View Date/Time Show Date/Time 3.2 Set Date/Time Set Date/Time 2014-01-01 08:00:00 3.3.1 Auto 3.3 Time Display 3.3.2 Always Auto 3. Date/Time 3.4 Exit n/a 4.1 Power Saving Disable/30/20/15/10/5 Sec. 15 Sec. 4.2 Auto Power Off Disable/30/20/15/10/5/3/1 Min. General Setting 4. Power Manager 4.3 Exit n/a 15 Min.

- 10 - MS926 User’s Manual Top Menu Sub Menu Level 1 Sub Menu Level 2/Options/Result Options/Result Default Setting 5.1 Enable 5. Setup By Label 5.2 Disable n/a Enable 6. FAC Default 6.1 Restore to FAC Default? Yes/No Save to Selected Customer Setting n/a 7. FW Version 7.1 Show Firmware Version V0.x n/a 8. Serial Number 8.1 Show SERIAL NUMBER XXXXXXXXX n/a n/a 9. Exit n/a n/a n/a Top Menu Sub Menu Level 1 Sub Menu Level 2/Options/Result Options/Result Default Setting Data & Memory 1. View / Edit Buff. 1.1. Show Buffer Data 1.1.1 Exit / Erase/ View ■ If choose Exit, back to DATA/ MEMORY Page ■ If choose Erase, delete data ■ If choose View, continue to view the buffer data ■ For Auto/Batch mode, pressing [ENTER]+[Down] / [ENTER]+[UP] keys to view data longer than 3 lines

- 11 - MS926 User’s Manual Top Menu Sub Menu Level 1 Sub Menu Level 2/Options/Result Options/Result Default Setting 2. Erase Buffer 2.1. Erase Buffer Yes/ No Erase entry if Yes selected 3. Free MEM Space 3.1 Show FREE BUFFER MEM n/a 4.1 CR 4.2 None 4.3 TAB 4.4 CRLF 4. Data Separator 4.5 LF CR 5. Sending BlkDly 5.1 Sending BlkDelay 10ms/3 Sec./1 Sec./500 ms./100 ms./50 ms. 10ms 6. Date/Time Stamp 6.1 DATE STAMP Disable/DDMMYYYY/ DD.MM.YYYY/ DD/MM/YYYY/ DD--MM--YYYY/ MMDDYYYY/ MM.DD.YYYY/ MM/DD/YYYY/ MM-DD-YYYY/ YYYYMMDD/ YYYY.MM.DD/ YYYY/MM/DD/ YYYY-MM-DD Disable

- 12 - MS926 User’s Manual Top Menu Sub Menu Level 1 Sub Menu Level 2/Options/Result Options/Result Default Setting 6.2 TIME STAMP Disable/HHMMAM/ HHMM/ HH:MM AM/ HH:MM/HHMMSSAM/ HHMMSS/ HH:MM:SS AM/ HH:MM:SS Disable 7.1 Disable Disable /Enable Disable 7.2 1:N Checking CHECKING START POSITION CHECKING LENGTH 7.2 1:1 Checking CHECKING START POSITION CHECKING LENGTH 7. Data Validation 7.3 Lookup Table Download Lookup 8. Exit n/a n/a n/a

- 13 - MS926 User’s Manual Top Menu Menu Result Default Setting 1. BT Pairing 1.1 Pairing 2.MAC Address 2.1 12 Characters Bluetooth MAC Address 3. Paired Device 3.1 Show PAIRED DEV NAME Show PAIRED DEV ADDR 4. Remove Pair 4.1 Remove pair 5. Signal Strength 5.1 Signal Strength Detection Enable / Disable Enable 6. BT FW Version 6.1 Show BT FW VERSION Bluetooth CONFIG 7. Exit

- 14 - MS926 User’s Manual Top Menu Menu Result Result Default Setting 1. Beeper Volume 1.1 Medium/ Low/ Mute/ High Medium 2. Vibrator 2.1 Disable/ Enable Disable 3.1 Good Read 3.1.1 Beeper & Vibrator Vibrator / Beeper None Beeper & Vibrator 3.2 Connection 3.2.1 Beeper & Vibrator Vibrator / Beeper None Beeper & Vibrator 3.3 Button 3.3.1 Beeper & Vibrator Vibrator / Beeper None Beeper & Vibrator 3.4 System Setting 3.4.1 Beeper & Vibrator Vibrator / Beeper None Beeper 3.5 System Warn/ Err 3.5.1 Beeper & Vibrator Vibrator / Beeper None Beeper 3.6 PwrOn 3.6.1 Beeper & Vibrator Vibrator / Beeper None Beeper & Vibrator 3.7 PwrOff Alarm 3.7.1 Beeper & Vibrator Vibrator / Beeper None Beeper & Vibrator 3. Indicators 3.8 Exit n/a n/a Beep & Vibrate 4. Exit n/a n/a n/a

- 15 - MS926 User’s Manual Top Menu Menu Options Options Default Setting 1. Disable All 1D OFF/ON OFF 2.1 UPC-A Enabled/Disabled Enabled 2.2 UPC-E Enabled/Disabled Enabled 2.3 EAN-8 Enabled/Disabled Enabled 2.4 EAN-13 Enabled/Disabled Enabled 2.5 CODE 39 Enabled/Disabled Enabled 2.6 CODE 128 Enabled/Disabled Enabled 2.7 GS1 128 Enabled/Disabled Enabled 2.8 I 2 of 5 Enabled/Disabled Enabled 2.9 NEC 2 of 5 Enabled/Disabled Enabled 2.10 CODE 93 Enabled/Disabled Enabled 2.11 Codabar Enabled/Disabled Enabled 2.12 GS1DataBar Omn Enabled/Disabled Enabled 2.13 GS1DataBar Ltd Enabled/Disabled Enabled 2.14 GS1DataBar Exp Enabled/Disabled Enabled 2.15 CODE 11 Enabled/Disabled Disabled 2.16 MSI Enabled/Disabled Disabled 2.17 UPC-E1 Enabled/Disabled Disabled 2.18 S 2 of 5 Indus Enabled/Disabled Disabled 2.19 S 2 of 5 IATA Enabled/Disabled Disabled 2.20 Matrix 2 of 5 Enabled/Disabled Disabled 2. 1D CODE SETTING 2.21 Exit Enabled/Disabled 3.1 China Post Enabled/Disabled Disabled 3.2 Korea Post Enabled/Disabled Disabled 3. 1D POSTAL CODE SETTING 3.3 Exit Enabled/Disabled 4. Disable All 2D OFF/ON OFF 5.1 QR Code Enabled/Disabled Enabled Barcode Setting 5. 2D CODE SETTING 5.2 Data Matrix Enabled/Disabled Enabled

- 16 - MS926 User’s Manual Top Menu Menu Options Options Default Setting 5.3 Aztec Code Enabled/Disabled Enabled 5.4 PDF417 Enabled/Disabled Enabled 5.5 Macro PDF417 Enabled/Disabled Enabled 5.6 Micro PDF417 Enabled/Disabled Disabled 5.7 MaxiCode Enabled/Disabled Disabled 5.8 Codablock A Enabled/Disabled Disabled 5.9 Codablock F Enabled/Disabled Disabled 5.10 GS1 Composite Enabled/Disabled Disabled 5.11 Han Xin Code Enabled/Disabled Disabled 5.12 Exit Enabled/Disabled 6.1 OFF OFF 6.2 Australian Enabled/Disabled Disabled 6.3 British Enabled/Disabled Disabled 6.4 Canadian Enabled/Disabled Disabled 6.5 China Post Enabled/Disabled Disabled 6.6 InfoMail Enabled/Disabled Disabled 6.7 Intelligent Mail Enabled/Disabled Disabled 6.8 Japanese Enabled/Disabled Disabled 6.9 KIX Enabled/Disabled Disabled 6.10 Planet Enabled/Disabled Disabled 6.11 Postal-4i Enabled/Disabled Disabled 6.12 Postnet Enabled/Disabled Disabled 6. 2D POSTAL CODE SETTING 6.13 Postnet w/B&B' Enabled/Disabled Disabled

- 17 - MS926 User’s Manual Top Menu Menu Options Options Default Setting 6.14 InfoMail British Enabled/Disabled Disabled 6.15 Intelligent Mail Postnet w/B&B' Enabled/Disabled Disabled 6.16 Postnet Postal-4i Enabled/Disabled Disabled 6.17 Postnet Intelligent Mail Enabled/Disabled Disabled 6.18 Postal-4i Intelligent Mail Enabled/Disabled Disabled 6.19 Postal-4i Postnet w/B&B' Enabled/Disabled Disabled 6.20 Planet Postnet Enabled/Disabled Disabled 6.21 Planet Postnet w/B&B' Enabled/Disabled Disabled 6.22 Planet Postal-4i Enabled/Disabled Disabled 6.23 Planet Intelligent Mail Enabled/Disabled Disabled 6.24 Planet Postnet Postal-4i Enabled/Disabled Disabled 6.25 Planet Postnet Intelligent Mail Enabled/Disabled Disabled6.26 Planet Postal-4i Intelligent Mail Enabled/Disabled Disabled6.27 Postnet Postal-4i Intelligent Mail Enabled/Disabled Disabled 6.28 Planet Postal-4i Postnet w/B&B' Enabled/Disabled Disabled 6.29 Planet Intelligent Mail Postnet w/B&B' Enabled/Disabled Disabled 6.30 Postal-4i Intelligent Mail Postnet w/B&B' Enabled/Disabled Disabled

- 18 - MS926 User’s Manual Top Menu Menu Options Options Default Setting 6.31 Planet Postal-4i Intelligent Mail Postnet Enabled/Disabled Disabled 6.32 Planet Postal-4i Intelligent Mail Postnet w/B&B' Enabled/Disabled Disabled 7. Exit n/a n/a n/a Top Menu Sub Menu Level 1 Result Default Setting 1. iOS Soft Keypad 1.1 iOS SOFT KEYPAD by DblClick Disable / Enable Disable 2. KBD Language 2.1 US English / Japanese / Partial ALT Danish/ ALT Mode/ French / German Italian / Norwegian / Spanish / Swedish/ Swiss/ UK English US English 3. KBD Case 3.1 Auto Trace / Upper/ Lower Auto Trace 4. KBD ChrDelay 4.1 1ms/ 100ms/ 50ms/ 20ms/ 10ms/ 5ms 1ms HID KEYBOARD SETTING 5. Exit n/a n/a Top Menu Menu Result Default Setting Remote SETTING 1. exit

- 19 - MS926 User’s Manual Chapter 2 - Installation 2.1 NFC Pairing with Mobile Devices 1. Ensure your host device supports NFC and that it is enabled. 2. Touch the back of the MS926 scanner to your host device. 3. Your device is now paired with MS926. 2.2 BT HID BT HID* Establishing BT connection in BT HID mode. 1. Use MS926 to scan BT HID barcode. 2. Press Page Down key then press Scan button to enter BT pairing mode. 3. Double-click Bluetooth Device icon in the toolbar on your PC. Select Add New Devices. When you see a device list windows, choose MS926-XXXX and then press Next. PC now is establishing BT connection. 4. MS926 will beep when your PC successfully establish a BT connection with MS926.

- 20 - MS926 User’s Manual 2.3 BT SPP BT SPP Establishing BT connection in BT SPP mode. 1. To establish BT connection between MS926 and your PC in BT SPP mode, you must install unitech CDC driver on your PC in advance. ( For CDC driver, please check on the product section on unitech website : http://www.ute.com ) 2. Use MS926 to scan BT SPP barcode. 3. Press Page Down key then press Scan button to enter BT pairing mode. 4. Double-click Bluetooth Device icon in the toolbar on your PC. Select Add New Devices. When you see a device list windows, choose MS926-XXXX and then press Next.. 5. When PC is establishing a BT connection in BT SPP mode with MS926, windows system will automatically install the required drivers. 6. Back to your PC toolbar, right click on the Bluetooth Device icon , choose Open Settings. Go to COM Port page and select in-coming COM port ;for example COM 28. 7. MS926 will beep when your PC successfully establish a BT connection with MS926.

- 21 - MS926 User’s Manual 2.4 BT SPP (Slave) BT SPP (Slave) Establishing BT connection in BT SPP (Slave) mode. 1. To establish a BT connection between MS926 and your PC in BT SPP (Slave) mode, you must install unitech CDC Driver on your PC in advance. ( For CDC driver, please check on the product section on unitech website : http://www.ute.com ) 2. Use MS926 to scan BT SPP (Slave) barcode. 3. Press Page Down key then press Scan button to enter BT pairing mode. 4. Double-click Bluetooth Device icon in the toolbar on your PC. Select Add New Devices. When you see a device list windows, choose MS926-XXXX and then press Next. 5. When PC is establishing a BT connection in BT SPP (Slave) mode with MS926, windows system will automatically install the required drivers. 6. Back to your PC toolbar, right click on the Bluetooth Device icon , choose Open Settings. Go to COM Port page and select out-going COM port; for example COM 27. 7. MS926 will beep when your PC successfully establish a BT connection with MS926.

- 22 - MS926 User’s Manual 2.5 USB SPP USB SPP Establishing connection in USB SPP mode. 1. To establish connection between MS926 and your PC in USB SPP mode, you must install unitech CDC Driver on your PC in advance. ( For CDC driver, please check on the product section on unitech website : http://www.ute.com ) 2. Use MS926 to scan USB SPP barcode. 3. Connect MS926 to your PC with a Micro USB-USB cable. 4. Go to PC device manager to check the COM information, for example; CDC USB Demonstration (COM40). 5. Back to the application, and select the corresponding COM port number. MS926 will beep when your pc successfully establish the connection with MS926.

- 23 - MS926 User’s Manual Chapter 3 – Symbology 3.1 All symbologies If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular sym-bology. Note: Scanner performance may reduce by scanning All Symobologies On. Only scan All Symbologies On when needed. Note : When All Symbologies On is scanned, 2D Postal Codes are not enabled.2D Postal Codes must be enabled separately. All Symbologies On All Symbologies Off 3.2 Message Length Description You are able to set the valid reading length of some of the bar code symbologies. You may wish to set the same value for minimum and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread. EXAMPLE: Decode only those bar codes with a count of 9-20 characters. Min. length = 09Max. length = 20 EXAMPLE: Decode only those bar codes with a count of 15 characters. Min. length = 15Max. length = 15

- 24 - MS926 User’s Manual For a value other than the minimum and maximum message length defaults, scan the bar codes included in the explanation of the symbology, then scan the digit value of the message length and Save bar codes on the Programming Chart. The minimum and maximum lengths and the defaults are included with the respective symbologies. 3.3 1D 3.3.1 Codabar Codabar On* Default All Codabar Settings Codabar Off 3.3.1.1 Codabar Start / Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit Don’t Transmit*

- 25 - MS926 User’s Manual 3.3.1.2 Codabar Check Characters Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar bar codes with Modulo 16 check characters. Default = No Check Character. No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate and Transmit, the scanner will only read Codabar bar codes printed with a check character, and will transmit this character at the end of the scanned data. When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. No Check Character* Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit

- 26 - MS926 User’s Manual 3.3.1.3 Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated into one with the “D” characters omitted. Select Require to prevent the scanner from decoding a single “D” Codabar symbol without its companion. This selection has no effect on Codabar symbols without Stop/Start D characters. On Off* Require 3.3.1.4 Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60. Minimum Message Length Maximum Message Length

- 27 - MS926 User’s Manual 3.3.2 Code 39 Code 39 On* Default All Code 39 Settings Code 39 Off 3.3.2.1 Code 39 Start / Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/ Stop characters. Default = Don’t Transmit. Transmit Don’t Transmit*

- 28 - MS926 User’s Manual 3.3.2.2 Code 39 Check Characters No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 bar codes printed with a check character, but will not transmit the check character with the scanned data. When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. No Check Character* Validate , but Don’t Transmit Validate and Transmit 3.3.2.3 Code 39 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 0-48. Minimum Default = 0, Maximum Default = 48. Minimum Message Length Maximum Message Length

- 29 - MS926 User’s Manual 3.3.2.4 Code 39 Append This function allows the scanner to append the data from several Code 39 bar codes together before transmitting them to the host computer. When the scanner encounters a Code 39 bar code with the append trigger character(s), it buffers Code 39 bar codes until it reads a Code 39 bar code that does not have the append trigger. The data is then transmitted in the order in which the bar codes were read (FIFO). Default = Off. Off * On 3.3.2.4 Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as PARAF. Note: Trioptic Code must be turned off while scanning Code 32 Pharmaceutical codes. Off * On

- 30 - MS926 User’s Manual 3.3.2.5 Full ASCIIIf Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off. Character pairs /M and /N decode as a minus sign and period respectively. Character pairs /P through /Y decode as 0 through 9. Off * On

- 31 - MS926 User’s Manual 3.3.2.6 Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were created (see ISO 2022/ISO 646 Character Replacements), and scan the value and the Save bar code from the Programming Chart. The data characters should then appear properly. Code 39 Code Page 3.3.3 Interleaved 2 of 5 Interleaved 2 of 5 On* Default All Interleaved 2 of 5 Settings Interleaved 2 of 5 Off

- 32 - MS926 User’s Manual 3.3.3.1 Check digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data. When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. No Check Digit* Validate , but Don’t Transmit Validate and Transmit 3.3.3.2 Interleaved 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length

- 33 - MS926 User’s Manual 3.3.4 Code 93 Code 93 On* Default All Code 93 Settings Code 93 Off 3.3.4.1 Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Minimum Message Length Maximum Message Length

- 34 - MS926 User’s Manual 3.3.4.2 Code 93 Append This function allows the scanner to append the data from several Code 93 bar codes together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 93 bar codes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data. The scanner stores the data in the order in which the bar codes are read, deleting the first space from each. The scanner transmits the appended data when it reads a Code 93 bar code that starts with a character other than a space. Default = Off. Off * On 3.3.4.3 Code 93 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were created (see ISO 2022/ISO 646 Character Replacements), and scan the value and the Save bar code from the Programming Chart. The data characters should then appear properly. Code 93 Code Page

- 35 - MS926 User’s Manual 3.3.5 Standard 2 of 5 Industrial (three-bar start/stop) Standard 2 of 5 Industrial On Default All Standard 2 of 5 Industrial Settings Standard 2 of 5 Industrial Off* 3.3.5.1 Standard 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length 3.3.6 Standard 2 of 5 IATA (two-bar start/stop) Standard 2 of 5 IATA Industrial On Default All Standard 2 of 5 IATA Industrial Settings Standard 2 of 5 IATA Industrial Off*

- 36 - MS926 User’s Manual 3.3.6.1 Standard 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length 3.3.7 Matrix 2 of 5 Matrix 2 of 5 On Default All Matrix 2 of 5 Settings Matrix 2 of 5 Off* 3.3.7.1 Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length

- 37 - MS926 User’s Manual 3.3.8 Code 11 Code 11 On Default All Code 11 Settings Code 11 Off* 3.3.8.1 Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits. One Check Digit Two Check Digits* 3.3.8.2 Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length

- 38 - MS926 User’s Manual 3.3.9 Code 128 Code 128 On* Default All Code 128 Settings Code 128 Off 3.3.9.1 ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner. The use of ISBT formats requires a paid license. The ISBT 128 Application Specification describes 1) the critical data elements for labeling blood products, 2) the current recommendation to use Code 128 due to its high degree of security and its space-efficient design, 3) a variation of Code 128 that supports concatenation of neigh-boring symbols, and 4) the standard layout for bar codes on a blood product label. Use the bar codes below to turn concatenation on or off. Default =Off. On Off*

- 39 - MS926 User’s Manual 3.3.9.2 Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80. Minimum Message Length Maximum Message Length 3.3.9.3 Code 128 Append This function allows the scanner to append the data from several Code 128 bar codes together before transmitting them to the host computer. When the scanner encounters a Code 128 bar code with the append trigger character(s), it buffers Code 128 bar codes until it reads a Code 128 bar code that does not have the append trigger. The data is then transmitted in the order in which the bar codes were read (FIFO). Default = On. On* Off

- 40 - MS926 User’s Manual 3.3.9.4 Code 128 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were created (see ISO 2022/ISO 646 Character Replacements), and scan the value and the Save bar code from the Programming Chart. The data characters should then appear properly. Code 128 Code Page 3.3.10 UPC-A Code UPC-A On* Default All UPC-A Settings Code UPC-A Off Note: To convert UPC-A bar codes to EAN-13, see Convert UPC-A to EAN-13. 3.3.10.1 UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. On* Off

- 41 - MS926 User’s Manual 3.3.10.2 UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. On* Off 3.3.10.3 UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda Off* 2 Digit Addenda On 5 Digit Addenda Off* 5 Digit Addenda On

- 42 - MS926 User’s Manual 3.3.10.4 UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda. Default = Not Required. Not Required* Required 3.3.10.5 UPC-A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. On * Off

- 43 - MS926 User’s Manual 3.3.10.6 UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting (Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes. If you scan the Allow Concatenation code, when the scanner sees the coupon code and the extended coupon code in a single scan, it transmits both as one symbology. Otherwise, it transmits the first coupon code it reads. If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a single read to transmit the data. No data is output unless both codes are read. Default = Off. Off* Allow Concatenation Require Concatenation

- 44 - MS926 User’s Manual 3.3.11 UPC-E0 Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number system, use UPC-E1. Default = On. Code UPC-A On* Default All UPC-E Settings Code UPC-A Off 3.3.11.1 UPC-E0 Expand UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format. Default = Off. Off * On 3.3.11.2 UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required. Not Required * Required

- 45 - MS926 User’s Manual 3.3.11.3 UPC-E0 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = On. On* Off 3.3.11.4 UPC-E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On. On* Off 3.3.11.5 UPC-E0 Leading Zero This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan Off. Default = On. On* Off

- 46 - MS926 User’s Manual 3.3.11.6 UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda. 3.3.12 UPC-E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use UPC-E0. If you need to read codes that lead with the 1 number system, use the UPC-E1 On selection. Default = Off. Off* On 2 Digit Addenda Off* 2 Digit Addenda On 5 Digit Addenda Off* 5 Digit Addenda On

- 47 - MS926 User’s Manual 3.3.13 EAN/JAN-13 EAN/JAN-13 On* Default All EAN/JAN Settings EAN/JAN-13 Off 3.3.13.1 Convert UPC-A to EAN-13 When UPC-A Converted to EAN-13 is selected, UPC-A bar codes are converted to 13 digit EAN-13 codes by adding a zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A. Do not Convert UPC-A* UPC-A Converted to EAN-13 3.3.13.2 EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. On* Off

- 48 - MS926 User’s Manual 3.3.13.3 EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 3.3.13.4 EAN/JAN-13 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-13 bar codes that have addenda. Default = Not Required. Not Required* Required 2 Digit Addenda Off* 2 Digit Addenda On 5 Digit Addenda Off* 5 Digit Addenda On

- 49 - MS926 User’s Manual 3.3.13.5 EAN/JAN-13 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = On. Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code. On* Off 3.3.14 EAN/JAN-8 EAN/JAN-8 On* Default All EAN/JAN-8 Settings EAN/JAN-8 Off 3.3.14.1 EAN/JAN-8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. On* Off

- 50 - MS926 User’s Manual 3.3.14.2 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 3.3.14.3 EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda. Default = Not Required. Not Required* Required 2 Digit Addenda Off* 2 Digit Addenda On 5 Digit Addenda Off* 5 Digit Addenda On

- 51 - MS926 User’s Manual 3.3.14.4 EAN/JAN-8 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = On. On* Off 3.3.15 MSI MSI On Default All MSI Settings MSI Off *

- 52 - MS926 User’s Manual 3.3.15.1 MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data. When Check Character is set to Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes printed with the specified type check character(s), but will not transmit the check character(s) with the scanned data. Validate Type 10, but Don’t Transmit* Validate Type 10 and Transmit Validate 2 Type 10 Characters, but Don’t Transmit Validate 2 Type 10 Characters and Transmit Validate Type 11 then Type 10 Character, but Don’t Transmit Validate Type 11 then Type 10 Character and Transmit Disable MSI Check Characters

- 53 - MS926 User’s Manual 3.3.15.2 MSI Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length 3.3.16 GS1 DataBar Omnidirectional GS1 DataBar Omnidirectional On* Default All GS1 DataBar Omnidirectional Settings GS1 DataBar Omnidirectional Off 3.3.17 GS1 DataBar Limited GS1 DataBar Limited On* Default All GS1 DataBar Limited Settings GS1 DataBar Limited Off

- 54 - MS926 User’s Manual 3.3.18 GS1 DataBar Expanded GS1 DataBar Expanded On* Default All GS1 DataBar Expanded Settings GS1 DataBar Expanded Off 3.3.18.1 GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74. Minimum Message Length Maximum Message Length 3.3.19 PDF 417 PDF 417 On* Default All PDF 417 Settings PDF 417 Off

- 55 - MS926 User’s Manual 3.3.19.1 PDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750. Minimum Message Length Maximum Message Length 3.3.20 QR Code QR Code On* Default All QR Code Settings QR Code Off 3.3.20.1 QR Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 1-7089. Minimum Default = 1, Maximum Default = 7089. Minimum Message Length Maximum Message Length

- 56 - MS926 User’s Manual 3.3.20.2 QR Code Append This function allows the scanner to append the data from several QR Code bar codes together before transmitting them to the host computer. When the scanner encounters an QR Code bar code with the append trigger character(s), it buffers the number of QR Code bar codes determined by information encoded in those bar codes. Once the proper number of codes is reached, the data is output in the order specified in the bar codes. Default = On. On* Off 3.3.20.3 QR Code Page QR Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were created (see ISO 2022/ISO 646 Character Replacements ), and scan the value and the Save bar code from the Programming Chart. The data characters should then appear properly. QR Code Page

- 57 - MS926 User’s Manual 3.3.21 Data Matrix Data Matrix On* Default All Data Matrix Settings Data Matrix Off 3.3.21.1 Data Matrix Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116. Minimum Message Length Maximum Message Length

$- 58 - MS926 User’s Manual 3.3.21.2 Data Matrix Append This function allows the scanner to append the data from several Data Matrix bar codes together before transmitting them to the host computer. When the scanner encounters an Data Matrix bar code with the append trigger character(s), it buffers the number of Data Matrix bar codes determined by information encoded in those bar codes. Once the proper number of codes is reached, the data is output in the order specified in the bar codes. \ Default = On. On* Off$

- 59 - MS926 User’s Manual 3.3.21.3 Data Matrix Code Page Data Matrix Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were created (see ISO 2022/ISO 646 Character Replacements ), and scan the value and the Save bar code from the Programming Chart. The data characters should then appear properly. Data Matrix Code Page 3.3.22 MaxiCode MaxiCode On Default All MaxiCode Settings MaxiCode Off* 3.3.22.1 MaxiCode Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150.. Minimum Message Length Maximum Message Length

- 60 - MS926 User’s Manual 3.3.23 Chinese Sensible (Han Xin) Code Han Xin On Default All Han Xin Settings Han Xin Off* 3.3.23.1 Han Xin Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833. Minimum Message Length Maximum Message Length

- 61 - MS926 User’s Manual 3.4 2D 3.4.1 Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combinations that are allowed. Only one 2D postal code selection can be active at a time. If you scan a second 2D postal code selection, the first selection is overwritten. Default = 2D Postal Codes Off. 2D Postal Codes Off 3.4.1.1 Single 2D Postal Codes Australian Post On British Post On Canadian Post On Intelligent Mail Bar Code On Japanese Post On KIX Post On Planet Code On

- 62 - MS926 User’s Manual Postal-4i On Postnet On Postnet with B and B’ Fields On InfoMail On 3.4.1.2 Combination 2D Postal Codes InfoMail and British Post On Postal-4i and Postnet with B and B’ Fields On Postnet and Postal-4i On Planet Code and Postal-4i On Postal-4i and Intelligent Mail Bar Code On

- 63 - MS926 User’s Manual Planet Code, Postnet, and Postal-4i On Planet Code and Postnet On Planet Code, Postal-4i, and Intelligent Mail Bar Code On Intelligent Mail Bar Code and Postnet with B and B’ Fields On Planet Code, Postal-4i, and Postnet with B and B’ Fields On Postnet and Intelligent Mail Bar Code On Postal-4i, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On Planet Code and Postnet with B and B’ Fields On

- 64 - MS926 User’s Manual Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On Planet Code and Intelligent Mail Bar Code On Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet On Planet Code, Postnet, and Intelligent Mail Bar Code On Postnet, Postal-4i, and Intelligent Mail Bar Code On Planet Code, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On

- 65 - MS926 User’s Manual 3.4.1.3 China Post (Hong Kong 2 of 5) China Post (Hong Kong 2 of 5) On Default All China Post (Hong Kong 2 of 5) Settings China Post (Hong Kong 2 of 5) Off* 3.4.1.4 China Post (Hong Kong 2 of 5) Message Length Scan the bar codes below to change the message length. Refer to Message Length Description for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length

- 66 - MS926 User’s Manual Chapter 4 – Command Settings 4.1 System setting 4.1.1 Default Scan below bar code to restore the factory setting Factory Default 4.1.2 Display FW version / Data Format Scan below bar code to show the current F/W & BT version FW version Scan the bar code below to show current data format settings. Data Format Settings

- 67 - MS926 User’s Manual 4.1.3 Auto Power Off Scan below bar code to set the time frame for auto power off 1 Minute 10 Minutes 30 Minutes 3 Minutes 15 Minutes 5 Minutes * 20 Minutes Disable 4.1.4 Power Saving Scan below bar code to set the time frame for power saving. 5 Seconds 20 Seconds 10 Seconds 30 Seconds 15 Seconds* Disable

- 68 - MS926 User’s Manual 4.2 BT pairing 4.2.1 Enter Pairing mode Scan below bar code to enter BT pairing mode BT Pairing 4.2.2 Paired device info. Scan below bar code to show the current paired device information Paired Device 4.2.3 Remove the pair Scan below bar code to remove BT pair Remove Pair

- 69 - MS926 User’s Manual 4.3 Output data transmit 4.3.1 Auto mode In this mode, when scanner is out off BT transmit range, the scanned data will be stored in the memory and transmit data automatically when back to in-range. Auto mode* 4.3.1.1 Erase last memory entry Scan below bar code to erase last scanned data in memory Erased Last Memory Entry 4.3.1.2 Erase all data in buffer (Erase Memory) Scan below bar code to erase all data in the memory Erase Memory 4.3.1.3 Check buffer memory space Scan below bar code to check buffer memory space Free Memory Space

- 70 - MS926 User’s Manual 4.3.2 Wedge mode In this mode, the data only transmit while the BT is connected Wedge mode 4.3.3 Batch mode In this mode, the scanned data will be stored in the memory all the time and transmit data only when BT is connected by scanned the “send batch” bar code Batch mode 4.3.3.1 Send batch Scan below bar code to send the stored data to host Send Batch 4.3.3.2 Erase last memory entry Scan below bar code to erase last scanned data in batch memory Erase Last Memory Entry

- 71 - MS926 User’s Manual 4.3.3.3 Erase all data in batch (Erase memory) Scan below bar code to erase all data in batch memory Erase Memory 4.3.3.4 Free batch memory space Scan below bar code to check batch memory space Free Memory Space

- 72 - MS926 User’s Manual 4.4 BT Config 4.4.1 HID keyboard block delay In BT HID mode, scan below bar code to set the block delay time. Default is 10ms. 10 ms * 50 ms 100 ms 500 ms 1 Sec. 3 Sec.

- 73 - MS926 User’s Manual 4.4.2 HID keyboard inter-character delay In BT HID mode, scan below bar code to set inter-character delay time. Default is 1ms. 1 ms * 5 ms 10 ms 20 ms 50 ms 100 ms 4.4.3 HID keyboard Case In BT HID mode, scan below bar code to change the alphabet case. Scan ‘’to lower” barcode to output data in lower case; or scan “to upper” barcode to output data in upper case. Default setting: “auto trace” to have original scanned data transmitted. Auto Trace * To Lower To Upper

- 74 - MS926 User’s Manual 4.4.4 HID keyboard language In BT HID mode, scan below bar code to change keyboard language. Default is US English US English * UK English Swiss Swedish Norwegian Italian German French Danish Partial ALT Japanese (OADG109) Spanish ALT Mode

- 75 - MS926 User’s Manual 4.5 Beep & Vibration 4.5.1 Beep Scan below bar code to adjust beep volume. Default: Medium volume 4.5.1.1 High volume High Volume 4.5.1.2 Medium volume * Medium Volume* 4.5.1.3 Low volume Low Volume 4.5.1.4 Mute Mute 4.5.2 Vibration The vibration is off in default. Scan below bar code to open vibration function Enable Vibrator Disable Vibrator *

- 76 - MS926 User’s Manual 4.5.3 Beep & Vibration Setting manually Please follow the steps to set up the Beep & Vibration.  Main Menu Beep & Vibrate Indicators Button Beeper & Vibrator * None Beeper Vibrator

- 77 - MS926 User’s Manual 4.6 Scan mode / Parameter Selection 4.6.1 Manual Trigger Mode When in manual trigger mode, the scanner scans until a bar code is read, or until the trigger is released. 4.6.1.1 LED Illumination - Manual Trigger If you wish to set the illumination LED brightness, scan one of the bar codes below. This sets the LED illumination for the scan engine when the trigger is pressed. Default = High. Note: The LEDs are like a flash on a camera. The lower the ambient light in the room, the brighter the LEDs need to be so the scan engine can “see” the bar codes. High* Medium Low Manual Trigger - Normal

- 78 - MS926 User’s Manual 4.6.2 Serial Trigger Mode You can activate the scan engine by pressing the trigger. When in serial mode, the scan engine scans until a bar code has been read or until the deactivate command is sent. The scan engine can also be set to turn itself off after a specified time has elapsed. 4.6.2.1 Read Time-Out Use this selection to set a time-out (in milliseconds) of the scan engine’s trigger when using serial commands to trigger the scan engine. Once the scan engine has timed out, you can activate the scan engine either by pressing the trigger or using a serial trigger command. After scanning the Read Time-Out bar code, set the time-out duration (from 0-300,000 milliseconds) by scanning digits on the Programming Chart, then scanning Save. Default = 30,000 ms. Read Time-Out 4.6.3 Presentation Mode Presentation Mode uses ambient light to detect bar codes. The LED dims until a bar code is presented to the scanner, then the LED brightens to read the code. If the light level in the room is not high enough, Presentation Mode may not work properly. Scan the following bar code to program your scanner for Presentation Mode. Presentation Mode

- 79 - MS926 User’s Manual 4.6.3.1 Idle Illumination - Presentation Mode Scan one of the bar codes below to set the LED illumination for the scanner when it is in an idle state in Presentation Mode. Default = High. Note: If you use one of the lower Idle Illumination settings, and there is not enough ambient light, the scanner may have difficulty detecting when a bar code is presented to it. If the scanner has difficulty “waking up” to read bar codes, you may need to set the Idle Illumination to a brighter setting. Note: LED Illumination - Presentation Mode does not apply to Poor Quality PDF Codes or Mobile Phone Read Mode. High* Medium Low 4.6.3.2 Presentation Sensitivity Presentation Sensitivity is a numeric range that increases or decreases the scan engine's reaction time to bar code presentation. To set the sensitivity, scan the Sensitivity bar code, then scan the degree of sensitivity (from 0-20) from the inside back cover, and Save. 0 is the most sensitive setting, and 20 is the least sensitive. Default = 1. Sensitivity

- 80 - MS926 User’s Manual 4.6.3.3 Centering Use Centering to narrow the scan engine’s field of view to make sure that when the scanner is hand-held, it reads only those bar codes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the desired codes are read. (Centering can be used in conjunction with Aimer Delay, for the most error-free operation in applications where multiple codes are spaced closely together. Using the Aimer Delay and Centering features, the scanner can emulate the operation of older systems, such as linear laser bar code scanners.)If a bar code is not touched by a predefined window, it will not be decoded or output by the scan engine. If centering is turned on by scanning Centering On, the scan engine only reads codes that pass through the centering window you specify using the Top of Centering Window and Bottom of Centering Window bar codes.

- 81 - MS926 User’s Manual 4.6.3.4 Presentation Centering Use Presentation Centering to narrow the scanner’s field of view when it is in the stand to make sure the scanner reads only those bar codes intended by the user. For instance, if multiple codes are placed closely together, Presentation Centering will insure that only the desired codes are read. To adjust centering when the scanner is hand-held, see Centering.If a bar code is not touched by a predefined window, it will not be decoded or output by the scanner. If Presentation Centering is turned on by scanning Presentation Centering On, the scanner only reads codes that pass through the centering window you specify using the Top of Presentation Centering Window, Bottom of Presentation Centering Window, Left, and Right of Presentation Centering Window bar codes. In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Bar Code 1 passes through he centering window, it will be read. Bar Code 2 does not pass through the centering window, so it will not be read. Note: A bar code needs only to be touched by the centering window in order to be read. It does not need to pass completely through the centering window.

- 82 - MS926 User’s Manual Scan Presentation Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual. Scan Save. Default Presentation Centering = 40% for Top and Left, 60% for Bottom and Right. Note: If you are taking images, you must set the In-Stand Sensor to Off. You may program a Streaming Presentation Mode (Normal, Enhanced, or Mobile Phone) you wish to use for in-stand scanning, and a Manual Trigger mode (Normal, Enhanced, or Mobile Phone) you wish to use for out-of-stand scanning. To do this, you must first scan the preferred Streaming Presentation mode (see below), then scan the Manual Trigger mode you want to use. Presentation Centering On Presentation Centering Off * Top of Presentation Centering Window Bottom of Presentation Centering Window Left of Presentation Centering Window Right of Presentation Centering Window

- 83 - MS926 User’s Manual 4.6.4 Poor Quality Codes 4.6.4.1 Poor Quality 1D Codes This setting improves the scanner’s ability to read damaged or badly printed linear bar codes. When Poor Quality 1D Reading On is scanned, poor quality linear bar code reading is improved, but the scanner’s snappiness is decreased, making it less aggressive when reading good quality bar codes. This setting does not affect 2D bar code reading. Default = Poor Quality 1D Reading Off. Poor Quality 1D Reading Off* Poor Quality 1D Reading On 4.6.4.2 Poor Quality PDF Codes This setting improves the scanner’s ability to read damaged or badly printed PDF codes by combining information from multiple images. When Poor Quality PDF On is scanned, poor quality PDF code reading is improved, but the scanner’s snappiness is decreased, making it less aggressive when reading good quality bar codes. This setting does not affect 1D bar code reading. Default = Poor Quality PDF Reading Off. Poor Quality PDF Reading Off* Poor Quality PDF Reading On

- 84 - MS926 User’s Manual 4.6.5 Mobile Phone Read Mode When this mode is selected, your scanner is optimized to read bar codes from mobile phone or other LED displays. However, the speed of scanning printed bar codes may be slightly lower when this mode is enabled. Note: To turn off Mobile Phone Read Mode, scan a Manual or Serial Trigger Mode bar code. Hand Held Scanning - Mobile Phone Presentation Scanning - Mobile Phone 4.6.6 Hands Free Time-Out The Scan Stand and Presentation Modes are referred to as “hands free” modes. If the scanner’s trigger is pulled when using a hands free mode, the scanner changes to manual trigger mode. You can set the time the scanner should remain in manual trigger mode by setting the Hands Free Time-Out. Once the time-out value is reached, (if there have been no further trigger pulls) the scanner reverts to the original hands free mode. Scan the Hands Free Time-Out bar code, then scan the time-out duration (from 0-300,000 milliseconds) from the inside back cover, and Save. Default = 5,000 ms. Hands Free Time-Out

- 85 - MS926 User’s Manual 4.6.7 Reread Delay This sets the time period before the scan engine can read the same bar code a second time. Setting a reread delay protects against accidental rereads of the same bar code. Longer delays are effective in minimizing accidental rereads. Use shorter delays in applications where repetitive bar code scanning is required. Reread Delay only works when in a Presentation Mode. Default = Medium. Short (500 ms) Medium (750 ms)* Long (1000 ms) Extra Long (2000 ms) 4.6.8 Aimer On/ Off This feature allows you to turn the aimer on and off. When the Interlaced bar code is scanned, the aimer is interlaced with the illumination LEDs. Default = Interlaced. Interlaced* Off

- 86 - MS926 User’s Manual 4.6.9 No Read With No Read turned On, the scan engine notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data Window, an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear. Default = Off. If you want a different notation than “NR,” for example, “Error,” or “Bad Code,” you can edit the output message (see Data Formatting ). The hex code for the No Read symbol is 9C. Off* On

- 87 - MS926 User’s Manual 4.6.10 Video Reverse Video Reverse is used to allow the scan engine to read bar codes that are inverted. The Video Reverse Off bar code below is an example of this type of bar code. Scan Video Reverse Only to read only inverted bar codes. Scan Video Reverse and Standard Bar Codes to read both types of codes. Note: After scanning Video Reverse Only, menu bar codes cannot be read. You must scan Video Reverse Off or Video Reverse and Standard Bar Codes in order to read menu bar codes. Note: Images downloaded from the unit are not reversed. This is a setting for decoding only. Video Reverse Off * Video Reverse and Standard Bar Codes Video Reverse Only

- 88 - MS926 User’s Manual 4.6.11 Working Orientation Some bar codes are direction-sensitive. For example, KIX codes and OCR can misread when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner. Default = Upright. Upright * Vertical, Bottom to Top Upside Down Vertical, Top to Bottom

$- 89 - MS926 User’s Manual 4.7 Prefix/Suffix selections 4.7.1 To Add a Prefix or Suffix Step 1. Scan the Add Prefix or Add Suffix symbol. Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Charts) for the symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Scan the 2 hex digits from the Programming Chart or scan 9, 9 for all symbologies. Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252), for the prefix or suffix you wish to enter. Note: To add the Code I.D., scan 5, C, 8, 0. To add AIM I.D., scan 5, C, 8, 1. To add a backslash (\), scan 5, C, 5, C. To add a backslash (\) as in Step 7, you must scan 5C twice – once to create the leading backslash and then to create the backslash itself. Step 5. Scan the 2 digit hex value from the Programming Chart. Step 6. Repeat Steps 4 and 5 for every prefix or suffix character. Step 7. Scan Save to exit and save, or scan Discard to exit without saving. Repeat Steps 1-6 to add a prefix or suffix for another symbology. Example: Add a Tab Suffix to All Symbologies : Step 1. Scan Add Suffix. Step 2. Scan 9, 9 from the Programming Chart to apply this suffix to all symbologies. Step 3. Scan 0, 9 from the Programming Chart. This corresponds with the hex value for a horizontal tab, shown in the ASCII Conversion Chart (Code Page 1252). Scan Save, or scan Discard to exit without saving.$

Unitech Electronics MS926BT BT Barcode Scanner User Manual

Unitech Electronics Co., Ltd. BT Barcode Scanner Users Manual

Users Manual

Navigation menu

Namespaces

Views

Navigation