Unitech Electronics PA600BT PDA Scanner User Manual PDA PA600 UM EN

Unitech Electronics Co., Ltd. PDA Scanner PDA PA600 UM EN

user manual

unitechPA600 Rugged Enterprise PDAUser’s Manual400546G Rev. A
Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliancecould void the user's authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposurelimits set forth for an uncontrolled environment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.
iPrefaceAbout This ManualThis manual explains how to install, operate and maintain the PA600 PDA Barcode Scanner. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from the manufacturer. This includes electronic or mechanical means, such as photocopying, recording, or infor-mation storage and retrieval systems. The material in this manual is subject to change without notice. © Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved.Bluetooth is a registered trademark of Bluetooth SIG. Microsoft, Windows and Active-Sync are either registered trademarks or trademarks of Microsoft Corporation. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.Regulatory Compliance StatementsFCC StatementThis is a FCC Part 15 Class B product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.Canadian Compliance StatementThis Class B Digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.The device is certified to the requirements of RSS-139-1 for 2.4 GHz spread spectrum devices.European Conformity StatementDeclaration of Conformity with Regard to the R&TTE 1999/5/EC and EMC 89/336/ EEC directives.
iiLaser InformationThe Unitech PA600 series is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1. Class II and Class 2 products are not considered to be hazardous. The PA600 series contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or during prescribed service operations.The laser safety warning label required by the DHHS/IEC for the PA600 series's optional laser scanner module is located on the memory compartment cover, on the back of the unit.CAUTION! Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light. Use of optical instruments with the scanner will increase eye hazard. Optical instruments include binoculars, microscopes, and magnifying glasses. This does not include eye glasses worn by the user.NoticesThis unit is equipped with a battery pack and backup battery. It is possible that the Unitech PA600 may not power-on due to battery discharge as a result of storage.In the above situation, plug the PA600 to the USB charging cable which is with DC in port or put the unit into the Unitech PA600 Cradle (with 5V/2A AC-DC adapter), and recharge the unit for 16 hours in order to fully charge its backup battery.The backup battery will charge from external power or the main battery (if the main battery still has enough power to turn on). In the event the main battery is fully charged, refrain from using the PA600 for 16 hours in order for the main battery to fully charge the backup battery.Backing-up data by backup battery only without the main battery installed in battery compartment may take as long as 6 hours. Therefore, in order to prevent data protec-tion failure due to backup battery failure, do not leave the PA962 without the recharge-able battery pack installed, or without connection to AC power for an extended period of time.Battery charge noticeIt is important to consider the environment temperature whenever you are charging the Lithium-Ion battery pack. The process is most efficient at normal room tempera-ture or slightly cooler. It is essential that you charge batteries within thestated range of -5°C to 50°C. Charging batteries outside of the specified range could damage the batteries and shorten their charging life cycle.
About This Manual iiiStorage and safety noticeAlthough charged Lithium-Ion batteries may be left unused for several months, their capacity may be depleted due to build up of internal resistance. If this happens they will require recharging prior to use. Lithium-Ion batteries may be stored at tempera-tures between-20°C to 60°C, however they may be depleted more rapidly at the high end of this range. It is recommended to store batteries within normal room tempera-ture ranges.
iv
vTable of ContentsPrefaceAbout This Manual iRegulatory Compliance Statements ............................................................................. iFCC Statement........................................................................................................................ iCanadian Compliance Statement............................................................................................ iEuropean Conformity Statement ............................................................................................. iLaser Information ................................................................................................................. iiNotices ...................................................................................................................................... iiBattery charge notice............................................................................................................... iiStorage and safety notice....................................................................................................... iiiChapter 1Getting Started 1Introducing the PA600....................................................................................................... 1Features................................................................................................................................... 2Package Contents ............................................................................................................... 3A Tour of the PA600............................................................................................................ 4Front Left View........................................................................................................................ 4Back View............................................................................................................................... 5Getting Started...................................................................................................................... 6Installing the Battery ............................................................................................................... 6Charging the Battery............................................................................................................... 8Charging the Battery using the USB Cable ....................................................................... 8Charging the Battery with the Docking Station .................................................................. 9Checking the Battery Status .............................................................................................. 9Connecting the PA600 to a PC............................................................................................. 10Turning the PA600 on for the First Time............................................................................... 11Powering On.................................................................................................................... 11Calibrating the PA600 Screen ......................................................................................... 12Chapter 2Using the Hardware 14Keypads and Function Buttons................................................................................... 14Adjusting the Screen Brightness................................................................................ 16Using the Stylus................................................................................................................. 16Using the SD/MMC memory card ................................................................................ 17Inserting a Storage Card ................................................................................................. 17Removing a Storage Card ............................................................................................... 17Using the Laser Scanner ................................................................................................ 18
viChapter 3Getting Connected 20Establishing Device-PC Connection.......................................................................... 20Installing Microsoft ActiveSync ............................................................................................. 20Connecting the Device to Your Computer ............................................................................ 23Synchronizing with Your Computer........................................................................... 24Connection options............................................................................................................... 24USB Connection .............................................................................................................. 24Infrared Connection ......................................................................................................... 25Bluetooth Connection ...................................................................................................... 26WiFi Connection .............................................................................................................. 29Synchronizing Information ............................................................................................ 30Synchronization Options....................................................................................................... 30Using ActiveSync to Exchange Files ........................................................................ 30Chapter 4Barcode Scanner Programs 32Scan2Key .............................................................................................................................. 32Scanner Setting.................................................................................................................. 32Barcode Symbologies........................................................................................................... 33Chapter 5Advance settings 34Adjusting Settings............................................................................................................. 34Checking the Main and Backup Battery Status..................................................... 35Extending Battery Life..................................................................................................... 36Changing the Automatic Power Settings .............................................................................. 36Adjusting Backlight Setting ................................................................................................... 37Viewing Flash Memory Files ......................................................................................... 38Performing a hardware reset ........................................................................................ 39Performing a Warm Boot ...................................................................................................... 39Preforming a Cool Boot ........................................................................................................ 40Method 1.......................................................................................................................... 40Method 2.......................................................................................................................... 41AppendixSystem Specifications 42
1Chapter 1Getting StartedIntroducing the PA600 Thank you for purchasing the PA600 PDA Barcode Scanner.Your PA600 was designed for user who need a compact and durable PDA for data collection and real time transactions. The PA600 is a rugged, compact and lightweight palm-size com-puter using the Windows Mobile 5.0 operating system, and incor-porating an integral bar code scanning laser device, color LCD with touchscreen, keypad, IrDA interface, and wireless communi-cation capability. It provides users with a standard Windows-based environment for customizing and operating the device.To reduce TCO, the PA600 is sealed to meet IP54 standards and has undergone multiple drop tests to prevent downtime.
2Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.FeaturesPowerful system• Microsoft Windows Mobile 5.0 / Windows CE NET 5.0 operating system• Intel PXA270 processor with speed of up to 520 MHzSystem memory• 64 MB SDRAM• 128 MB Flash ROMDisplay• 3.5-inch QVGA LCD touch-sensi-tive screen• 320 x 240 resolutionBarcode scanner• Built-in Bar Code Scan Engine• Built-in vibrator for scanning indi-cation• CCD scan engine (optional)• Symbol SE950 support• UNITECH HAMSTER barcode decoderCommunication• USB Host & Client• IrDA 1.2 (SIR)• GPRS (Data Only)• VOIP support• 802.11b/g for power saving• Bluetooth version 1.2 (supports Bluetooth Printer, Bluetooth Modem, Bluetooth ActiveSync)Audio• Voice recording and playback•MIC• Speaker• Headset Connector• ReceiverWireless connectivity• 802.11b + g with diversity antenna• Bluetooth wireless technology• Serial infrared portExpansion slotSDIO slotBattery life• Normal usage: 6 hours• Charging time: 3.5 hours• Embedded backup battery cellUser-friendly interface• Quick launch hot keys for enabling backlight, calibration, software key-board, and other device manage-ment tasks• Trigger keys for barcode scanning
Chapter 1 Getting Started 3Package ContentsAfter opening the box, ensure the following accessories for the PA600 are present:If anything is missing or appear damaged in any way, contact your dealer.PA600 Terminal AC AdapterBattery Pack Stylus USB Charging Cables Elastic Stylus String CD-ROMQuick Reference Guide
4Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.A Tour of the PA600The following sections describe the main components and features of the PA600.Front Left ViewNo. Component Description1. Status indicator Indicates the battery charging and barcode scanning status.Green - Battery is fully charged, the device is running on battery power, or barcode scanning process is completed without error.Red - Battery is charging, barcode scanner is activated and processing.2. Left scanner trigger buttonPress to activate the barcode laser scanner. 3. Power button If the device is off, press this button to turn it on.Alternatively, when the unit is on, this key must be pressed and held down for about two seconds in order to turn the device off.4. Microphone Enables you to record voice audio.5. Universal connectorConnects your device to a USB charging cable, which in turn connects to the computer’s USB port and through the AC adapter to an electrical outlet.This allows you to recharge your device and perform an ActiveSync operation.You can also use it to connect a peripheral hardware, such as an docking station, to your device.6. Keypad Keypad interface for controlling the PA600. See Keypads and Function Buttons on page 14 for more information.7. LCD Touch screen Displays the applications and data stored on your device. It is touch-sensitive and responds to the stylus or finger.8. Speaker Enables you to hear audio from the PA600.
Chapter 1 Getting Started 5Back ViewNo. Component Description9. Battery compartment Houses the Removable and rechargeable 3.7 V, 1950 mAH battery pack10. Battery compartment release latchOpens the battery compartment.11. Reset button Press the end of the stylus into the button to reset your device.12. Handstrap Enables you to securely hold the PA600 while using it.13. Speaker Enables you to hear audio from the PA600.14. Strap holder Attachment location for holding hand strap, carrying strap, and stylus.15. Memory card slot Accommodates Secure Digital memory cards. 16. Barcode scanner window Used to scan barcodes.17. Earphone jack Connects to audio line-out devices (earphones or headphones) for use in noisy environments.18. Stylus Enables you to interact with the operating system. To use the stylus, remove it from its holder and hold it the same way you hold a pen or pencil.19. Right scanner trigger buttonPress to activate the barcode laser scanner. 20. Infrared (IR) port Uses infrared technology to transmit and receive data from other IR-enabled devices.
6Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Getting StartedThis section explains how to install and charge the battery, how to check battery sta-tus, how to turn on the PA600, and how to calibrate the screen.Installing the BatteryWARNING! There is a risk of fire and burns if the battery pack is handled improp-erly. DO NOT disassemble, crush, puncture, short external contacts, or dispose the battery pack in fire or water. DO NOT attempt to open or service the battery pack. Dispose of used batteries according to local recycling guidelines in your area.A backup battery cell is embedded into your device to prevent data loss in instances when the removable battery pack is removed or completely discharged. This backup battery cell will only support the system for a maximum of 60 minutes.NOTE: To enable the internal battery cell to provide backup power supply, charge your device with the main battery pack for at least 12 hours.1. Open the battery compartment by pushing the latch in the direction of the arrow and lifting up.The battery compartment is displayed:NOTE: The plastic battery tab makes it easy to remove the battery.Compartment contactsPlastic battery tabBattery securing clip
Chapter 1 Getting Started 72. Position the battery pack, making sure the battery contacts are aligned with the contacts in the compartment and the battery is placed on top of the plastic tab, as shown in the following illustration.3. Slide the battery pack into the battery bay while simultaneously pulling the plas-tic tab and securing clip until the battery clicks into place.4. Replace the battery compartment cover.ContactsPlastic tabPlastic tabSecuring clip
8Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Charging the BatteryBefore using the PA600 for the first time, you need to charge it for about 16 hours. After that, you can charge the PA600 every day to recharge the battery to full capacity. Charge the PA600 using the USB charging cable or the docking station.CAUTION! Operating the PA600 for the first time without the AC adapter, and without fully charging the backup battery may result in loss of data stored in RAM memory. When the main battery is removed, the backup battery retains RAM data in memory for 2 hours, please charge the battery for the period to avoid the data loss in RAM mem-ory.NOTE: Data you enter may not be properly stored until the built-in backup bat-tery has been adequately charged.Charging the Battery using the USB Cable1. Press and hold the connector button on the USB charging cable and connect it to the PA600 (1).2. Plug the AC adapter cable into the power jack on the USB charging cable (2).3. Connect the AC adapter into an electrical outlet (3).
Chapter 1 Getting Started 9Charging the Battery with the Docking Station1. Plug the AC adapter cable into the power jack on the docking station, then con-nect the AC adapter into an electrical outlet.2. Slide the device into the docking station until it clicks into place. 3. The connection is secure when the bottom edge of the device is aligned with the docking station, and the LED indicator on the device lights up red.Checking the Battery StatusIf the battery level becomes low in the course of normal use, a status icon appears on the device screen indicating low or very low battery status. In both cases, perform an Active-Sync operation to back up your data, then recharge your device as soon as possible.If the battery level reaches low status, the device will enter sleep mode; if the battery level reaches very low status, the device will enter deep sleep mode. In this case, you have about 72 hours to recharge your device after which you risk losing all data on your device’s internal memory.LED StatusLED MeaningPA600 Solid Red ChargingSolid Green Charging completeDocking StationPower LED Power is onCharging LED: ChargingSync LED Synchronization is taking place
10Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Connecting the PA600 to a PCUse the USB cable to connect the PA600 to a PC to use with ActiveSync.1. Press and hold the connector button on the USB charging cable and connect it to the PA600 (1).2. Plug the USB connector into the USB port on the PC and connect the AC adapter into the USB connector (2).3. Connect the AC adapter into an electrical outlet (3).
Chapter 1 Getting Started 11Turning the PA600 on for the First TimeAfter you have initially charged your device for about 12 hours, the device is ready to be used. You can now start up your device where you’ll calibrate the display, learn some basic stylus usage, and set up the system time zone, date and time.Powering On1. Turn on your device by pressing the power button on the front panel.NOTE: The PA600 screen ships with a protective plastic film. You may remove this if desired by peeling from one corner. The screen will be more susceptible to scratch-ing without the film, but will be more readable.2. The Unitech PA600 welcome screen appears for a moment fol-lowed by the Windows CE screen.Power Button
12Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Calibrating the PA600 ScreenThe calibrate screen automatically appears when the unit is powered-on for the first time or after the system is reset. To calibrate the screen at any time, follow these instructions. 1. Tap Start → Settings, and then click the System tab.2. Tap the Screen icon.
Chapter 1 Getting Started 13The Screen Settings window appears. This window enables you to customize the screen settings. 3. Tap Align Screen to calibrate the screen. The align screen window appears.4. Tap the cross hair firmly and accurately. The cross hair moves to the next location.5. Continue tapping the cross hairs until the screen has been calibrated.
14Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Chapter 2Using the HardwareKeypads and Function ButtonsThe keypad enables you to both enter information and interact with the PDA operating system and also operate secondary functions using the function button. When the green function button is pressed, the green icon functions on the keypad become available. When the Function button is pressed, an icon appears in the operating system:The following table describes the keypad keys.Key Main Function Secondary FunctionTurns the PA600 on and off. —Number 1 Left soft key - activates function above in LCD screen.Alphanumeric 2, a, b, c Up navigation keyAlphanumeric 3, d, e, f Right soft key - activates function above in LCD screen.Function activated icon
Chapter 2 Using the Hardware 15Enter key OKBack space Escape keyAlphanumeric 4, g, h, i Left navigation keyAlphanumeric 5, j, k, l —Alphanumeric 6, m, n, o Right navigation key—Enables disables secondary function keysTab Windows key opens Start menuAlphanumeric 7, p, q, r, s Decreases screen brightnessAlphanumeric 8, t, u, v Down navigation keyAlphanumeric 9, w, x, y, z Increases screen brightnessAlpha —Asterisk Illuminates keypadNumber 0, space —Period PoundKey Main Function Secondary Function
16Adjusting the Screen BrightnessAdjust the screen brightness by pressing the Function button to enable the soft keys and pressing the 7 (decrease bright-ness) or 9 (increase brightness) buttons.Using the StylusCAUTION! Never use anything other than the PA600 stylus on the screen. Using another object as a stylus could cause permanent damage.1. Remove the stylus from its holder.2. Hold the stylus as you would a pencil.3. To make a choice from a menu, lightly tap the tip of the stylus on that choice.4. To write data into a field on a form, use the stylus to print the letters or numbers. Use very light pressure.Function ButtonIncreaseBrightnessDecreaseBrightnessCopyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 2 Using the Hardware 17Using the SD/MMC memory cardYour device has an expansion slot compatible with a range of SD and MMC storage cards, which are primarily used to back up or transfer files and data. The slot also sup-ports SDIO cards for added connectivity options. Inserting a Storage Card1. Remove the two screws from the SD compartment cover and remove the cover.2. Insert the SD card with the notched corner as shown by the icon on the case. 3. Push the card into the slot until you hear an audible system sound; this will sig-nal that the card is already properly seated within the slot. The card is secure when it is not protruding from the slot.Removing a Storage Card1. Remove the two screws from the SD compartment cover and remove the cover.2. Press the card in and release. The card pops out. An audible system sound will signal that the card has been released.3. Remove the card from the slot.
18Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Using the Laser ScannerThe PA600 has an integrated laser scanner which reads all major bar code labels with excellent performance.NOTE: Reading software must be enabled in order to operate the scanner. This can be a user-loaded application or a pre-loaded utility such as Scanner Setting.Activate the laser scanner by pressing either one of the trigger keys located on the left and right side of the unit. The PA600 has a built-in Scanner Setting util-ity that allows you to test the device’s barcode scan function.1. To launch Scanner Settings, tap Start → Settings → System → Scanner Settings.2. The Scanner Control Panel opens.From here you can configure barcode scanner parameters such as enabling or disabling barcode symbologies, setting data transmission options, configuring magnetic and proximity reading options, and setting power management options. Scan button
Chapter 2 Using the Hardware 193. To test the barcode scanner, tap the Test tab and press one of the scanner buttons on a barcode. The screen will display the results of the scan.
20Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Chapter 3Getting ConnectedEstablishing Device-PC ConnectionInstalling Microsoft ActiveSyncIn order to exchange data between your computer and PA600, Microsoft ActiveSync must be installed on your computer. Use the USB charging cable that comes with your device to connect the device to your computer.NOTE: If you have a previous version of the Microsoft ActiveSync installed in your computer, uninstall it first before installing the latest version of Microsoft ActiveSync.To install Microsoft ActiveSync on your computer:1. Close any open programs, including those that run at startup, and disable any virus-scanning software.2. Download the ActiveSync software from the Microsoft ActiveSync Download page at http://www.microsoft.com/windowsmobile/ downloads/activesync42.mspx.3. Browse to the location of the downloaded file, and double-click it. The installation wizard begins.
Chapter 3 Getting Connected 214. Click Next. You are prompted to read the End User License Agreement (EULA).5. Accept the license agreement terms and click Next. You are prompted for user information.6. Type the user name and organization and click Next. You are prompted for the destination folder.
227. Select a drive to install the program to and click Next.The installation wizard has gathered the information it needs to install Active-Sync and prompts you to begin installation.8. Click Install. The program begins installationAfter the program has finished installing you see the following screen.Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 3 Getting Connected 239. Click Finish. You may be prompted to restart your computer.After you have installed ActiveSync and restarted your computer, the ActiveSync icon appears in your computer’s system tray as shown and ActiveSync Connection Wizard starts. For detailed information on how to use ActiveSync on your computer, start ActiveSync then click Help → Microsoft ActiveSync Help.Connecting the Device to Your Computer1. After ActiveSync has been installed, connect the USB charging cable to the uni-versal connector on the bottom of your device. If necessary, connect an adapter. Refer to Connecting the PA600 to a PC on page 10.2. Plug the other end of the USB charging cable into a USB port on your com-puter.3. Turn the device on.4. ActiveSync starts automatically and configure the USB port to work with the PA600. The New Partnership setup wizard will automatically start.NOTE: If ActiveSync doesn’t start automatically, click Start → Programs → Microsoft ActiveSync.If a message appears indicating that it is unable to detect a connection, click the Cancel button and manually configure the communication set-tings. 5. Follow the onscreen instructions.6. When the configuration process is complete, the ActiveSync window appears.7. Synchronization will be initialized and will take place if you’ve chosen to syn-chronize periodically or upon connection.NOTE: Your computer can create a partnership with multiple PA600s. Also, a PA600 can create a partnership with up to two computers.
24Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Synchronizing with Your ComputerSynchronization takes place according to the options you choose while setting up ActiveSync on your computer. If you accept the default (On Connect) synchronization option in the Microsoft ActiveSync Setup Wizard, you’ll be able to simply connect your PA600 to your desktop computer and synchronization will take place.If you have not enabled the On Connect feature in Active Sync, you can start Active-Sync in either of the following ways:• On your computer, double-click My Computer → Mobile Devices folder.• Connect the USB cable between the computer and PA600.• Execute “Rellpog.exe” from the PA600 Windows directory Connection optionsYou can set remote synchronization with your computer using the following connec-tion options:• USB connection• Infrared connection• Bluetooth connection• WiFi connectionUSB ConnectionTo synchronize with your computer using a USB connection:1. Open ActiveSync.2. Connect your device to your computer using the USB charging cable.3. Initiate connection by tapping Start → Programs → ActiveSync.4. Tap Menu → Connections.5. Select Synchronize all PCs using this con-nection check box.6. Select a baud rate or cable type connec-tion.7. Tap OK.
Chapter 3 Getting Connected 25Infrared ConnectionThe infrared port allows you to synchronize information with an infrared enabled com-puter. Align the infrared port of your device with the infrared port on the computer. This method is ideal for quickly switching between multiple devices since there are no cables or adapters to change.1. Perform the steps below on your computer:a. Configure an infrared port on your computer following the manufacturer’s instructions. b. Once your computer’s IR port is ready, open ActiveSync. c. Click File → Connection Settings. d. Check Allow connec-tions to one of the fol-lowing and select Infrared Port (IR) from the drop-down list. e. Click OK.
26Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.2. Perform the steps below on your device:a. Align the IR port of your PA600 with that on your computer so that they are unobstructed and within close range. b. Initiate connection by tapping Start → ActiveSync → Menu → Connect via IR. c. Tap Sync.Bluetooth ConnectionYour device is equipped with Bluetooth wireless technology that you can use to syn-chronize information with a computer equipped with a Bluetooth adapter or access point. Bluetooth wireless technology allows you to communicate with the computer whenever it is within range.Follow these instructions to set up a Bluetooth connection.1. Tap Start → Settings → Connections → Bluetooth → Mode and check Turn on Bluetooth.
Chapter 3 Getting Connected 272. Tap Devices → New Partnership…3. Select a device from the list and tap Next.You are prompted for a passkey. 4. Enter the Passkey.
28Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.On the PC screen, you are prompted to enter the Bluetooth PIN Code Request.5. Enter the same Blue-tooth PIN Code you entered in step 4.6. On the PA600 tap Partnership Settings → Check Serial Port → Finish. 7. On your PC, click Active-Sync → Connection Set-ting → Select COM Port (COM 14) → OK8. On the PA6008 tap Start → Programs → ActiveSync → Menu → Connect via Bluetooth.
Chapter 3 Getting Connected 29WiFi ConnectionWith the device’s embedded WLAN module, you can send and receive signals to a WiFi network then synchronize files.NOTE: WiFi access requires a separate purchase of a service contract with a wireless service provider. Contact a wireless service provider for more information.A wireless network can be added either when the network is detected or by manually entering settings information. Before doing these steps, determine if authentication information is needed.1. Tap Start → Settings, then tap the Connections tab.2. Tap Network Cards.The Configure Network Adapters screen appears.3. Select whether the network card connects to the Internet or your work LAN from the drop-down list. 4. If there are networks already detected, tap and hold network name, then select Connect.5. Under the Network to access, select from the following network connection options:– All available– Only access points– Only computer-to-computer6. When finished, tap OK.For more information on how to configure the wireless network settings, tap Start → Help.
30Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Synchronizing InformationAll files created on the device are stored in My Document/PA600 My Document folder (if the designated device name is PA600). You can view files by double-clicking the PA600 My Documents icon on your computer.If you have enabled file synchronization, your PA600 files are automatically synchro-nized in the My Documents folder on your computer, unless a different name was cho-sen for PA600.Synchronization OptionsSynchronization options can be modified, including when you synchronize and what gets synchronized. In the Mobile Device window, click Tools → Sync Options.For each type of information, the synchronization process can be hastened by limiting the amount of data to be synchronized. To do this, select a service and click the Set-tings button. After enabling a service, you must close and reopen the ActiveSync.Using ActiveSync to Exchange FilesYou can use ActiveSync to exchange information from your device your computer and vice versa. Changes you make to the information on one location will not affect the information on the other one. If you want to automatically update information on both your device and computer, synchronize the information instead.You can copy two types of information to your device: files and Pocket Access Win-dows CE Store information.The procedure below only applies to copying files. Refer to the ActiveSync Help on your computer for instructions on how to copy Pocket Access Windows CE Store information.NOTE: Files created on your computer may need to be converted by Active-Sync so that they can be viewed and edited on your device, and vice versa.To copy files:1. Connect your device to your computer.2. In ActiveSync on your computer, click Explore.
Chapter 3 Getting Connected 31Windows Explorer opens the Mobile Device window for your device.3. Locate the file that you want to copy on your device or computer.4. Do either one of the following:– To copy the file to your device, right-click the file and click Copy. Place the cursor in the desired folder for your device, right-click, then click Paste.– To copy the file to your computer, right-click the file and click Copy. Place the cursor in the desired folder for your computer, right click, then click Paste.
32Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Chapter 4Barcode Scanner ProgramsScan2KeyThe Scan2Key application routes input from a scanner port to a keypad buffer, making all input from the scanner emulate input from the keypad. Using Scan2Key, scanned data can be directly input into a scanner port aware application such as MS Mobile Word.Scanner SettingWhen it is necessary for the user to change the default barcode symbology for a differ-ent application, the Scanner Control Panel provides the ability to change default sym-bology, place delimiter characters behind scanned data, and save the settings.Tap Start → Settings → System → Scanner Settings to display the Scanner Control Panel.
Chapter 4 Barcode Scanner Programs 33Barcode SymbologiesNote: *Value Adjustable Scanner Control Pannel V3.0Barcode SymbologyEnable/DisableCheck Char/Digit verificationTransmit Check Char/digitMax/Min LengthTransmit Leading DigitOtherLookland EAN YESCodabar YES YES YES Transmet Start/Stop bits, CLSI format, *data lengthCode 11 YES YES * check digits, *data lengthCode 128 YES *data lengthCode 32 YES YES Transmit Tailing digitCode 39 YES YES For ASCII, Transmit Start/Stop bits, Function Code, Double label decoding,*data length, *double labels separatorCode 93 YES Yes *data lengthDeta Code YES YES YESEAN 128 YES Yes Transmit Code ID, * Field separatorEAN 13 YES YES YESEAN 8 YES YES YES * Not suppress first or last digit, *data lengthInterleaved 2 of 5YES YES YES Fixed Length, * Not suppress first or last digit, *data lengthLabel Code IV&VYES YESMSI/Plessey YES YES * Check digit double module 10, * data lengthStandard 2 of 5YES YES YES Fixed Length, *Data LengthTelepen YES *Standard Character SetUPC A YES YES YESUPC E YES YES YES Zero Expension,NSCUPC/EAN GroupSupplement 2, Supplement 5,Insert Space before supplement, most have supplement, *Add-on code try level
34Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Chapter 5Advance settingsAdjusting SettingsThis section describes how to adjust the settings of your device to accommodate your work habits. To access Settings, tap Start → Settings.The Settings screen appears.From here can adjust such user configurable items as the backlight, auto power off timer, sys-tem volume, and processor speed. You can also assign functions to buttons, configure menus, enter owner information, and set up connec-tions.
35Checking the Main and Backup Battery StatusThis section describes how to view the power level for both the main and backup bat-tery. To minimize power consumption, you can define settings for the auto-off function and the processor’s operation speed.To check the main and backup battery status:1. Open Power Properties. Do either of the following:– If the Plug or Battery icon appears on your device, double-tap the icon to bring the Power Properties screen.– Tap Start → Settings → System → Power.Plug iconChapter 5 Advance settings
36Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.The Power screen appears.2. The battery menu item displays the status of the main and backup batteries. On the screen shown here, both batteries are at almost 100% charge.NOTE: It is necessary to charge the bat-tery when the battery charge reaches below 10%. If the battery does not accept a charge, contact Unitech Technical Support.Extending Battery LifeYou can extend the PA600 battery life by doing either of the following:• Change the automatic power settings• Minimize the use of backlightChanging the Automatic Power SettingsThe PA600 will enter idle mode when there is no task, or all tasks are waiting for input. In default setting, the PA600 automatically turns itself off if it remains idle for 3 minutes and when there is no external charging power connected. Pressing the power button returns the PA600 to the same point at the time of automatic shutdown.To change the automatic power settings:1. In the Power screen tap the Advanced tab. 2. Tap the automatic shut off time arrow to select from a list of time periods. The available time periods are 1, 2, 3, 4, and 5 minutes.3. This function can also be activated when the PA600 is plugged into the power adapter or placed in its docking station by tapping the On external power check box and then tapping the arrow to select from a list of time periods. The available time periods are 1, 2, 5,10, 15 and 30 minutes.
37Adjusting Backlight SettingThe power consumption of the LCD backlight is high, turn off the backlight function if it is not necessary.If a backlight is required, set “automatically turn off the backlight” function.To change backlight settings:1. Tap Start → Settings → System.2. Tap Backlight.The Backlight screen appears.3. Do any of the following:– In the Battery Power tab, tap the Turn off backlight if device is not used for check box and select the amount of time before the unit turns off the back-light while running in battery power mode from the drop-down list.– In the External Power tab, tap the Turn off backlight if device is not used for check box and select the amount of time before the unit turns off the back-light while running in battery power mode from the drop-down list.– Tap the Turn on the backlight key... checkbox to activate the backlight when the software keyboard is enabled.Chapter 5 Advance settings
38Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.– In the Brightness tab, tap and drag the slider to choose a dimmer backlight when operating on battery power. Viewing Flash Memory FilesFlash memory is rewritable location for programs and data files. The benefit of this feature is that files and programs saved in Flash Memory are unaffected by the PA600 power status.To access the Flash Memory files:1. Connect the device to your computer. See page 24.2. On your computer, click My Computer > Flash Storage.To transfer files to Device’s Flash Memory:1. Connect the device to your computer. See page 24.2. On your computer, click My Computer > Flash Storage.3. Select the file that you want to save.4. Click File > Save To and select Flash Storage.
Chapter 5 Advance settings 39Performing a hardware resetYou may have to perform a reset if the device freezes (i.e., device no longer responds to the buttons on the screen).A soft reset allows your device to get a fresh start, similar to rebooting a computer. This will restart your device and adjust memory allocation. All records and entries are retained after a soft reset. Unsaved data in open programs may in some cases be lost.Performing a Warm Boot1. Remove the stylus from its holder.2. Lightly press the tip of the stylus to the reset button located on the rear of the PA600.Reset buttonChapter 5 Advance settings
40Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.Preforming a Cool BootA hard reset cuts off power to your device, erasing all records and entries, deleting all programs you have added, and restoring the device to default factory settings. Never perform a hard reset unless a soft reset does not correct your problem. When you perform your next ActiveSync operation, you can restore any data that you previ-ously synchronized to your computer or you can restore data that you backed up to a storage card.NOTE: When you perform a hard reset, the date and time settings are not be retained. Formats, preferences, and other settings are restored to their default factory settings.Method 1Follow these instructions to perform a cool boot.1. Press and hold the Backspace key. 2. While holding the Backspace key, insert the tip of the stylus into the reset hole on the back of the PA600 and press and hold the reset button until you see the Unitech splash logo screen appear and then release the Backspace and reset buttons.NOTE: The system is returned to the default settings. All registry settings and all files (include the hidden files) are returned to their original factory defaults
Chapter 5 Advance settings 41Method 21. Press and hold the TAB key. 2. While holding the TAB key, insert the tip of the stylus into the reset hole on the back of the PA600 and press and hold the reset button until you see the Unitech splash logo screen appear and then release the TAB and reset buttons.NOTE: All registry settings are returned to default settings. You must reinstall all software. All files in flash memory are retained.
42Copyright 2006 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.AppendixSystem SpecificationsProcessing/Memory CPU Intel PXA270 520MHzMemory SDRAM:64MBFlash ROM:128MBOS Window Mobile 5.0 / Windows CE.NET 5.0Keypad 18-Key, including numeric key, alpha key and function keyDisplay 240x320 QVGA, Color Transflective TFT,with Touch Screen & backlightScanner Laser Scan Engine, CCD Scan Engine as optionalIndicator Led, VibratorCommunication USB Host & ClientIrDA 1.2(SIR)GPRS (Data Only)802.11b/g for power savingBluetoothBluetooth supports Bluetooth Printer, Bluetooth Modem,Bluetooth ActiveSyncAudio MICSpeakerHeadset ConnectorReceiverExpansion Slot SDIO slotPower Source Main 3.7V 1950mAH Li-ion battery packBackup One rechargeable Ni-MH backup batteryEnclosure Weight Under 300g with battery & scan engineDimension Approximately L149.5 X H26.6 X W85mmEnvironmental Operating temperature 0 C~ 50 CStorage temperature -20 C~ 60 CRelative Humidity 5% ~ 95%(non-condensing)Drop test to Concrete 4 feetEnvironmental Sealing IP54Models GPRS + BT802.11b/g + BTBT OnlyCertification CE, FCC, BSMI, VCCI, RoHS compliantAccessories Desktop Cradle4 slot Battery ChargerVehicle Quick Charging CableHolsterSoftware Microsoft Visual Studio 2005Microsoft Windows Mobile 5.0 SDKUnitech PA600 SDKVOIP (via 3rd party)

Navigation menu