United Integrated Services SCT-230 Wireless Environment sensor User Manual
United Integrated Services CO., LTD. Wireless Environment sensor
User manual
Confidential
SCT-230/STH-230 User's
Manual
Wireless Environment sensor
Confidential 1
Contents
一、 Product Overview ..........................................................................................1
二、 Product Features.............................................................................................2
三、 Installation operation .....................................................................................3
四、 Precautions.....................................................................................................4
五、 Troubleshooting .............................................................................................5
六、 Product Specifications ...................................................................................5
Confidential 1
一、Product Overview
1. Product Name：Wireless Contact Sensor
2. Model：SCT-230
3. Power Supply：CR123A Battery (3V) x 1
4. Dimensions (mm) and Accessories：Detect body, magnets, batteries, manual
82(L)mm x 25.5(W)mm x 17.5(H) mm
1. LED window
2. Reed switch
position
3. Setting key
(SET)
4. CR123A
Battery
5. Screws
Confidential 2
二、Product Features
1. The wireless signal magnetic reed switch or the temperature and humidity of the
transfer to the host、Panel Coordinator or Route, we can see that the doors and windows
open and close or the temperature and humidity the current state, to prevent thieves
invasive
2. Use CR123A Battery, battery power is insufficient to inform the host will
automatically operate a very low power; the battery can be used for
more than one year
3. Easy link, when install at the first time to press the set button on the side
of product joining with Gateway、Panel Coordinator or Route
Confidential 3
三、Installation operation
1. Placed batteries in the battery holder, as shown below. (Note: In accordance with the
polarity of the battery icon)
SCT-230/STH-230 on both sides to suppress uprooted open into the battery is completed
2. Connection: (EZ-MODE)
To register the first host device ready－Press Gateway (host) or short press Router
(router) behind the SET button，Then press the SET button on the rear of the machine。
At this point the host device and this opportunity within about 20 seconds while
flashing red light；When the connection (join) success，The machine's LED will start
blinking red light 20 seconds of micro, At this point if it can be paired (Binding)
devices to join or press the SET button. Would try pairing， If the pairing is successful
then stop lights， If the pairing fails, then goes off after 20 seconds。
3. If the connection fails，The two parties in 15 seconds the device will look after the long
red flash。
4. Fixed base (restricted flat screw) and the magnet holder，Installed on windows and
doors to detect，Before being started. The following figure.
Fixed base (restricted flat screw)
Confidential 4
5.
Lift connection：
Press quickly the rear of the machine SET key twice (Double Key), this time flashing
red light, inherent in 5 seconds behind the machine even by SET key twice, this
opportunity about three seconds after the long flashed red, that means lifting
connection successful.
6.
Wireless signal strength test (RSSI, Received Signal Strength Indication)：
Press quickly the rear of the machine SET key twice (Double Key), this time
flashing red light, inherent in 5 seconds behind the machine by double-clicking
the SET button a second, this time in front of a different three kinds of LED light
flashes to indicate how fast the wireless signal strength:
(1) Signal Good: Fast flashing red light 15 seconds.
(2) Weak signals: Slow flashing red light 15 seconds.
(3) No Signal: red light three seconds, off one second.
7. Anti-removal function: When the unit and system connection, then closed his cover, 5
seconds after the flash two times, that is to start anti-removal function. When the cover
is opened that will send a message notification (flash 3 times)
四、Precautions
1. SCT-230/STH-230 front top left there is an arrow mark, to be aligned with the center
line of the magnet cover (pictured), when two or more intervals than 10mm, it will send
a radio warning.
2. Recommended that the wall-mounted base, with screw lock screw hole locations or
gum paste, fixed to a stationary part of the door or window frame, magnet fixed to the
door or window frame movable parts. As shown below
Proposed installation location
Confidential 5
Please note that the machine being installed vertically, horizontally mounted upside
down or avoid, avoid anti-removal operation does not function properly when installed,
and cause excessive consumption phenomenon.
五、Troubleshooting
1. Abnormal conditions: SCT-230/STH-230 LED flashes the number of exceptions, do
not recognize the connection status. Treatment:
a. Ssure the battery is in good condition, the polarity is correct.
b. Restore the factory default reset the connection.
c. Handle invalid if the above situation, please contact your dealer.
2. Abnormal conditions: Unable to connect with the wireless host. Treatment:
The first to test the wireless signal strength RSSI way, and then confirm the distance
between the host SCT-230/STH-230, and is within the effective range of 50 meters
straight unsheltered. If the shelter will shorten the effective distance, you can shorten
the distance between the two, or adding repeaters, re-test for any improvement.
六、Product Specifications
UIS/ Wireless Environment sensor
Model No. SCT-230/STH-230
Electrical Specification
Transmit Frequency 2.4GHz ISM band, IEEE802.15.4: 2405 ~ 2480MHz
Operation Range Up to 50 meters (LOS)
Operating Voltage 3.0 VDC
Battery Type CR123A Battery (3V) x 1
Battery Life Up to 2 year
LED Indicator Red
Environmental Requirement
Operating Temperature 0°C to 50°C
Storage Temperature -10°C to 55°C
Humidity 90% RH Max., Non-Condensing
Mechanical Specification
Dimension (WxHxD, mm) 15.7x25.5x82
Weight (w/o Battery) 14g
Confidential 6
Notice : The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements,
the antenna(s) used for this transmitter must be installed to provide a separation distance
of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter. No change to the antenna or the device is
permitted. Any change to the antenna or the device could result in the device exceeding
the RF exposure requirements and void user’s authority to operate the device.