United Integrated Services WBC-110 Wireless Button Controller User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1198367
Application ID	0S0eADuJw2Mv9eLhWrXhag==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.78kB (172226 bits)
Date Submitted	2009-11-12 00:00:00
Date Available	2009-11-12 00:00:00
Creation Date	2009-11-03 17:01:43
Producing Software	Acrobat Distiller 9.2.0 (Windows)
Document Lastmod	2009-11-03 17:02:00
Document Title	Users Manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	jinnchen

Wireless Button Controller User's Manual
Product Name:
Wireless Button Controller
Model No: WBC-110
Input Power: 3V DC
Features Description:
1. To wireless transmission the button signals to the repeater set, you can start or lifting function.
2. Use CR2032 type Li-ion batteries, battery power is insufficient to inform the host will
automatically operate a very low power; the battery can be used for more than two years.
3. Easy link, when install at the first time to press the set button on the side of product binding
with repeater.
Outline Dimensions:
Dimension (W*H*D, mm) 31*65*13
Feature Locator:
1. Full Arm Button (FA)
2. Partial Arm Button
3. Disarm Button (DA)
4. State of LED window
5. (SET) Setting button
Installation Hints:
1. WBC-110(Wireless Button Controller) by pressing the SET button at the bottom, and then
press the WR-110 (wireless repeater) at the bottom of the SET button, Wait for 30 seconds to
1 minute. If LED indicator light flash three times that means linking success. If LED indicator
light flash two times that means fail.
2. Join to link with Gateway, please reference user manual of WCC-110 (Wireless console
controller).
3. Disarm Button (DA) function:
Disable all burglarproof sensor alarms BUT enable all anti-disaster sensor alarms.
4. Partial Arm Button (PA) function:
Enable all partial_arm_mode-enabled burglarproof sensor alarms AND enable all
anti-disaster sensor alarms.
5. Full Arm Button (FA) function: Enable all sensor alarms.
6. If start any Button (DA) (PA) (FA) the Green LED flash that means linking success.
7. WBC-110(Wireless Button Controller) Battery installation instructions are as follows maps,
(Dismount four screws removed , Separate cover from top to bottom, Replacement of internal
battery , Installed in accordance with the reverse order back).
(Attention: CR2032 Battery Positive side up)
Troubleshooting:
1. Problem: When link with WR-110 (Wireless repeater), there is no display of LED
indicator light for WBC-110 (Wireless Button Controller) to flash two or three
times.
Solution : a. Need to make sure the battery is good there is electricity, the installation of the
battery positive and negative direction is correct.
b. May be not press set button, need to link with repeater again.
c. If the above handles are invalid, please contact with agency
Specification:
Wireless Button Controller
Model No.
WBC-110
Electrical Specification
Transmit Frequency
2.4GHz
Modulation
GFSK
Transmit Power
0 dBm
Channel spacing
1 MHz
Channel NO.
81 Channel(2401~2481Mhz)
Range of operation
10 meters
Operating voltage
3.0V DC
Current (typical)
Working:
14mA Peak
Standby:
1 uA Max
Battery Type
CR2032
Battery Quantity (PCS)
Display Type
Red / Green LED indicator
Operation Interface
Push Switch *3
Environmental Requirement
Operating temperature
-10°C to 40°C
Storage temperature
-20°C to 60°C
Humidity
90% RH Max. Non-Condensing
Mechanical Specification
Dimension (WxHxD, mm)
31*65*13
Weight (No Battery)
26g
Weight (Include Battery)
30g
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
–
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Canada Warning
"Industry Canada regulatory information Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference,
including
interference that may cause undesired operation of the device.""The user is cautioned that this
device should be used only as specified within this manual to meet RF exposure
requirements. Use of this device in a manner inconsistent with this manual could lead to
excessive RF exposure conditions."

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : jinnchen
Create Date                     : 2009:11:03 17:01:43+08:00
Modify Date                     : 2009:11:03 17:02:00+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.2.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2009:11:03 17:02+08:00
Format                          : application/pdf
Title                           : <4D6963726F736F667420576F7264202D20AD5EA4E55FA8CFA5CEBBA1A9FAAED12E646F63>
Creator                         : jinnchen
Document ID                     : uuid:ee959d12-5b43-4b8b-8612-e62ae40b0a13
Instance ID                     : uuid:2a9dca66-c76a-4f11-9975-bad74302b76e
Page Count                      : 4

EXIF Metadata provided by EXIF.tools