Universal Electronics 4350 Comcast XR11v2 Remote 2014 User Manual
Universal Electronics Inc Comcast XR11v2 Remote 2014
User Manual
Remote with Voice Control
Start
Press and hold the Setup button (about 3 seconds)
until the Status LED changes from red to green.
Press the XFINITY button.
Follow the on-screen instructions to enter the
3-digit code that appears.
Once the code is correctly entered, your XFINITY
Remote is paired with the device.
Using the list on the right, nd the rst
5-digit code for your TV manufacturer.
Press and hold the Setup button (about
3 seconds) until the Status LED changes
from red to green.
Enter the rst 5-digit code for your TV
manufacturer. The Status LED should
ash green twice.
Verify that the code was accepted by using
your remote to adjust volume and turn the
TV on and o.
A
B
C
A
B
C
D
Status LED
All Power
Voice Control
Push and hold to talk.
Discover content by
channel, program or key
words.
Number Keys
Use predictive text (T9) to
quickly search for content.
TV Input
Changes to the next
available input on your TV
(if programmed in Step 4) Not working? Try the second code listed. Still
not working? Visit xnity.com/remotes for a
complete list of manufacturer codes.
Pick up your remote and remove the “Pull” tab
(on back) by pulling away from the remote. The
Status LED will blink green four times as the remote
powers up (about 5 seconds).
Turn on your TV.
Turn on your set-top box.
A
B
C
Back
If your code isn’t listed or you would
like to control an audio device, visit
xnity.com/remotes.
Popular Manufacturer Codes
LG 10178 , 11265
Panasonic 10051, 10250
Samsung 10812, 10060
Sanyo 10154, 10159
Sony 10000, 11100
Sharp 10093, 10165
Toshiba 10156, 11156
Vizio 1175 8, 11756
A
B
C
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not used in accordance with
the instructions, may cause harmful interference to radio
communications.
There is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase or decrease the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a circuit
dierent from that which the receiver is connected.
• Consult the dealer or an experienced remote control/
TV technician for help.
• It is strongly recommended that the TV be plugged
into a separate wall outlet.
The user is cautioned that changes and modications made to
this equipment without the approval of the manufacturer could
void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
“Caution” : Exposure to Radio Frequency Radiation. Antenna
shall be mounted in such a manner to minimize the potential
for human contact during operation to avoid the possibility of
exceeding the FCC radio frequency exposure limit.
Radio Exposure Statement: This equipment complies with the
FCC radiation exposure limits set forth for devices operating
in an uncontrolled environment. This equipment should be
operated with a minimum distance of 2 cm between the
radiator and front of face. This equipment should not be placed
directly on the ear when the speaker is active.
Pair Remote for “Aim Anywhere” ControlMeet Your Remote Turn On Your Remote Control Your TV’s Power and Volume
1 32 4
Control your set-top box without having to point your remote
at the device, even when it is located inside a cabinet or
entertainment center.
Your remote arrives with the AA batteries already installed,
but not activated. Here is how to power it on for the rst time.
Test Voice Control
5
Once your remote is paired with your set-top box, you can use
voice control.
FCC Compliance Statement
Press and hold the Voice button until
you hear the audio tone.
Speak a voice command to the remote
while continuing to hold down the
button. Try one of the suggestions to the
left. The Status LED will be solid blue
while you speak your command.
Release the Voice button when your
command is complete. Look at the TV for
the results of your voice command.
Not working? Make sure you’re pressing the
Voice button while you speak into the remote,
and release it when complete.
TV Power
XFINITY / Menu
Access Guide, Saved,
XFINITY On Demand, Apps,
Search and Settings.
Setup
Program remote for Aim
Anywhere or to control your
TV or audio device.
Need to remove Aim Anywhere control? Press
and hold the Setup button on the remote until the
status LED changes from red to green. Press A on
the remote. If the status LED blinks green twice,
you have successfully removed Aim Anywhere.
Not working? Make sure the battery tab from
your remote is removed, your TV is on and you are
entering the correct 3-digit code on your TV screen.
WATCH CNBC
FIND The Voice
SHOW ME all Eagles games
SHOW ME all kids movies on HBO
RECORD The Biggest Loser
LAUNCH Pandora
GUIDE
WHAT SHOULD I WATCH?
WHAT’S ON NOW?