Universal Electronics 59007 UE878 LGA Module User Manual

Universal Electronics Inc UE878 LGA Module Users Manual

Users Manual

JPN UE878 Standard BLE LGA ModulePart Number: 59007-9999999Quick Reference Guide
PAIRING BLE MODULE (English)1. Apply Power 3.3V to module2. Send serial command via UART3. Module will be in advisement modeCautionPlease read these safety instructions to ensure our personal safety and prevent property damageWarning- Do not put remote in a fire- Do not disassemble the remote control- Disposal of the remote controlA warning that batteries shall not be exposed to excessive heat such as sunshine, fire or thelike.Important Safety Instruction1. Read these instruction2. Keep these instruction3. Head all warning4. Follow all instructions5. Do not use this apparatus near water6. Clean only with dry cloth7. Do not install near any heat source such as radiators, heat registers, stoves or otherapparatus (including amplifiers) that produce heat.8. Only use attachment/accessories specified by manufacture9. Refer all servicing to qualified service personnel. Service is required when apparatus hasbeen damaged in any way, such as liquid has been spilled or objects have fallen into theapparatus, the apparatus has been exposed to rain or moisture, dose not operatenormally, or has been dropped.SpecificationOperating Temperature: -10 degree - 40 degreeOperating Voltage: 3.3V
COMPLIANCE WITH FCC RULES AND REGULATIONS15.21You are cautioned that changes or modifications not expressly approved by the part responsiblefor compliance could void the user’s authority to operate the equipment.15.105(b)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and if not used in accordance with the instructions, maycause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase or decrease the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.• Consult the dealer or an experienced remote control/ TV technician for help.This equipment has been verified to comply with the limits for aClass B computing device, pursuant to FCC Rules. The user iscautioned that changes and modifications made to the equipmentwithout the approval of manufacturer could void the user'sauthority to operate this equipment.FCC RF Radiation Exposure Statement:To comply with the FCC RF exposure compliance requirements, this device and its antenna mustnot be co-located or operating in conjunction with any other antenna or transmitter.This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.FCC Authorization LabelThis device complies with part 15 of the FCC Rules. Operation issubject to the following two conditions:1. This device may not cause harmful interference.2 This device must accept any interference received, includinginterference that may cause undesired operation.
End Product Labeling: The final end product must be labeled in a visible area with the following: “Contains FCC ID: xxxxxx”This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.Warning Statement:Europe-EU Declaration of Conformity and RestrictionsHereby, SONY declares that this Voice Remote Control is in compliance with the essentialrequirements and other relevant provisions of Directive 2014/53/EU.This equipment is marked with the symbol and can be used throughout the European community.This indicates compliance with the RE Directive 2014/53/EU and meets the relevant parts offollowing technical specifications:EN300328 v2.1.1: 2016EN301489-1 v2.1.1: 2016 (draft) / -17 v3.1.1: 2016 (draft)EN60065: 2014EN62479: 2010EN55032: 2012+AC: 2013; EN55024: 2010+A1: 2015
CAUTIONRISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPEUnder Industry Canada regulations, this radio transmitter may only operate using an antenna of atype and maximum (or lesser) gain approved for the transmitter by Industry Canada.To reduce potential radio interference to other users, the antenna type and its gain should be sochosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessaryfor successful communication.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subjectto the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of thedevice.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.This Class B digital apparatus complies with Canadian ICES-003Cet appareil numérique de classe B est conforme à la norme NMB-003.RF Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de
20 cm de distance entre la source de rayonnement et votre corps.End Product Labeling: The final end product must be labeled in a visible area with the following: “Contains IC: xxxxx-xxxxx”This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna Type: PCB Antenna Peak Gain: 2.5dBi
安全注意事項根據 NCC 低功率電波輻射性電機管理辦法 規定:第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。‘La operación de este equipo está sujeta a las siguientes dos condiciones”1. Es posible que este equipo o dispositivo no cause interferencia perjudicial2. Este equipo o dispositivo debe aceptar cualquier interferencia. Incluyendo la que puedacausar su operación no deseada.’‘Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferênciaa sistemas operando em caráter primário.’

Navigation menu