Universal Global Scientific UNA-A 3G Module User Manual UNA A EVB V14 2

Download:
Mirror Download [FCC.gov]
Document ID	2619090
Application ID	xdZ4qHjGKM6Y/nk5+4pOsg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	95.15kB (1189410 bits)
Date Submitted	2015-05-19 00:00:00
Date Available	2015-11-16 00:00:00
Creation Date	2015-03-27 11:07:10
Producing Software	GPL Ghostscript 9.05
Document Lastmod	2015-05-15 11:07:15
Document Title	UNA-A EVB User manual_V14_2
Document Creator	PDFCreator Version 1.3.2
Document Author:	tw023621

Doc. Title
UNA -A EVB User Manual
Originator
Max
Date
2015/03/20
Version
V14
1/16
Rev 1.1
Revision Record
Version
1.1
1.2
1.3
1.4
Revise content
New release
EVB V12
EVB V13
Add FCC/IC/CE warning statement include
2/16
Date
2014-10-03
2014-12-27
2015-03-02
2015-03-20
Rev 1.1
UNA-A EVB User Guide
1. Illustration of Function EVB
J2
J4
J6
J5
U2
Top View
J1
J3
Bottom View
3/16
Rev 1.1
Component
Function
Description
J1
Test Conn.
MP test connector.
J2
USB Conn.
J3
SMA Conn.
Connect to external Antenna
J4
Test Conn.
Debug connector.
J5
Power supply IN
Optional Connect to external Power supply input.
J6
GND
System GND.
U2
SIM Conn.
SIM card slot.
reference
Connect host PC or download firmware.(Micro USB).
note1.
Note1: USB port , doesn't provide the power input.
2. Configure the UNA-A EVB
J15
Top View
Download Key :
Component reference
J15
Function
Enable Download mode.
Note: To enable download mode, Please close J15 and refer to “MTK_flashtool_UserGuide”
4/16
Rev 1.1
3. General action
Step1. Insert SIM card.
Step2. Set up Antenna.
5/16
Rev 1.1
Step3. Connect computer by USB cable.
Step4. Set up Power In.
a. J5 is power input, and voltage range is from 3.4 to 4.35V.
b. J6 is GND.
6/16
Rev 1.1
Computer
Power supply.(3.4V~4.35V)
USB Cable
Diagram of Application
4. Settings for Download Mode
Component reference
Open/Short
Function
Open
Close Download mode
Short
Start Download mode
J15
7/16
Rev 1.1
Step1. Put back the jumper,J15.( Two kinds of selection)
Step2. Connect EVB and computer by USB cable.
Step3. Set up Power In.
a. J1 is power input, and voltage range is from 3.4 to 4.35V.
b. J2 is GND.
8/16
Rev 1.1
EVB test point pin define
J1 Pin define(Bottom view)
49
50
Pin number
Pin name
Pin number
Pin name
VBAT
RESERVE
VBAT
RESERVE
VBAT
RESERVE
GND
GND
GND
10
GND
11
NC
12
NC
13
NC
14
NC
15
GND
16
GND
17
GPI_2
18
NC
19
NC
20
GPI_1
21
U1RXD
22
U1TXD
23
U1RTS
24
U1CTS
25
FW_READY
26
WAKEUP_AP
27
RESERVE
28
SAR_DET
29
NC
30
NC
31
U0TXD
32
U0RXD
33
NC
34
NC
35
NC
36
NC
37
NC
38
NC
39
DL KEY
40
EINT0
41
NC
42
VDD_UART
43
NC
44
NC
45
NC
46
NC
47
NC
48
NC
49
NC
50
NC
9/16
Rev 1.1
FCC Regulations
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna
and
users, and the maximum antenna gain allowed for use with this device is 3dBi.
10/16
Rev 1.1
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains FCC ID:
COF-UNA-A”. The grantee's FCC ID can be used only when all FCC compliance
requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module. The end user manual shall include all required
regulatory information/warning as show in this manual.
Industry Canada(IC) statement:
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
11/16
Rev 1.1
suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement."
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec
un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions:
(For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les
conditions suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est
respectée entre l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou
antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
12/16
Rev 1.1
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada authorization
is no longer considered valid and the IC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne
peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera
chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une
autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains IC:
10293A-UNAA”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où
l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être
maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un
endroit visible avec l'inscription suivante: "Contient des IC: 10293A-UNAA".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as show
in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de
13/16
Rev 1.1
l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires
requises et avertissements comme indiqué dans ce manuel.
CE (European Union Notice)
Česky
[Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se
Dansk
[Danish]
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets
typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv
základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme
tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, [name of manufacturer], declares that this [type of equipment] is in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de
equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones
aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ∆ΗΛΩΝΕΙ ΟΤΙ [type of equipment]
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est
conforme aux exigences essentielles et aux autres dispositions pertinentes de la
directive 1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio]
è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla
direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of
equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un
citiem ar to saistītajiem noteikumiem.
14/16
Rev 1.1
Lietuvių
[Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlan
ds [Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in
Malti
[Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma
overeenstemming is met de essentiële eisen en de andere relevante bepalingen
van richtlijn 1999/5/EG.
mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
Magyar
[Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó
Polski
[Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z
alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami
Dyrektywy 1999/5/EC.
Portuguê
[Portuguese
Slovensk
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com
os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in
[Slovenian]
ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensk
y [Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a
Suomi
[Finnish]
všetky príslušné ustanovenia Smernice 1999/5/ES.
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen
tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja
sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med
de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår
av direktiv 1999/5/EG.
This device complies with the R&TTE Directive (1999/5/EC) issued by the Commission
of the European Community.
A minimum separation distance of 20 cm must be maintained between the user’s body
and the device, including the antenna during body-worn operation to comply with the
RF exposure requirements in Europe.
R&TTE Regulation:
15/16
Rev 1.1
In all cases assessment of the final product must be mass against the Essential
requirements of the R&TTE Directive Articles 3.1(a) and (b), safety and EMC
respectively, as well as any relevant Article 3.3 requirements.
The maximum antenna gain for frequency 900 is 3 dBi; for frequency 1800 is 3 dBi and
the antenna separation distance is 20cm.
2200
16/16
Rev 1.1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : GPL Ghostscript 9.05
Keywords                        : 
Modify Date                     : 2015:05:15 11:07:15+08:00
Create Date                     : 2015:03:27 11:07:10+08:00
Creator Tool                    : PDFCreator Version 1.3.2
Metadata Date                   : 2015:05:15 11:07:15+08:00
Document ID                     : uuid:eeacbc50-d689-11e4-0000-830215533ca3
Instance ID                     : uuid:1c622f1f-b92f-4860-9dab-621a3b2c6620
Format                          : application/pdf
Title                           : UNA-A EVB User manual_V14_2
Creator                         : tw023621
Description                     : ()
Page Count                      : 16
Subject                         : 
Author                          : tw023621

EXIF Metadata provided by EXIF.tools