Universal Global Scientific WMBNBM26A 802.11b/g/n + BT Wireless LAN Module User Manual Unlock rev

WM-BN-BM-26_A WiFi+BT Module User Manual

PWN: 802.11b/g/n + BT Wireless LAN Module

FVIN: 7.10.324.2

WiFi User Guide

User SIDO interface in PC/NB to control WM-BN-BM-26_A

Bluetooth User Guide

Install Bluetool on PC firstly. User UART in PC to control Bluetooth.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna

or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

20cm between the radiator & your body.

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna and

users, and

2) The transmitter module may not be co-located with any other transmitter or antenna.

As long as 2 conditions above are met, further transmitter test will not be required. However,

the OEM integrator is still responsible for testing their end-product for any additional

compliance requirements required with this module installed

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain

laptop configurations or co-location with another transmitter), then the FCC authorization is

no longer considered valid and the FCC ID can not be used on the final product. In these

circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be

installed such that 20 cm may be maintained between the antenna and users. The final end

product must be labeled in a visible area with the following: “Contains FCC ID:

COF-WMBNBM26A”. The grantee's FCC ID can be used only when all FCC compliance

requirements are met.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding

how to install or remove this RF module in the user’s manual of the end product which

integrates this module.

The end user manual shall include all required regulatory information/warning as show in

this manual.

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed with 20 cm is maintained between the antenna and users in

mobile or fixed applications.

2) The Antenna for Module (COF-WMBNBM26A ) is Non-detachable and the maximum

antenna gain allowed for use with this device is 3.68 dBi.

3) The transmitter module may not be co-located with any other transmitter or antenna.

4) OEM integrators Must demonstrate SAR test and meet compliance before end-product with

module ( COF-WMBNBM26A) marketed in portable application.

As long as 2 conditions above are met, further transmitter test will not be required. However, the

OEM integrator is still responsible for testing their end-product for any additional compliance

requirements required with this module installed.

OEM integrators Must demonstrate Part 15B test and meet compliance before end-product with

module ( COF-WMBNBM26A) marketed.

a

ntenna

g

ain allowed

f

or use with this device is 3.68 dBi.

4)

O

EM inte

g

rators Must demonstrate SAR test and meet com

p

liance be

f

ore end-

p

roduct with

module

(

C

O

F-WMBNBM2

6

A

)

marketed

in porta

bl

e app

l

ication

.

OEM inte

g

rators Must

d

emonstrate Part 15B test and meet com

p

liance be

f

ore end-

p

roduct with

module

(

C

O

F-WMBNBM2

6

A

)

marketed.

Industry Canada statement:

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas

produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris

un brouillage susceptible de provoquer un fonctionnement indésirable.

Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20

cm de distance entre la source de rayonnement et votre corps.

This device is intended only for OEM integrators under the following conditions: (For module device use)

1) The antenna must be installed such that 20 cm is maintained between the antenna and users,

and

2) The transmitter module may not be co-located with any other transmitter or antenna.

As long as 2 conditions above are met, further transmitter test will not be required. However, the

OEM integrator is still responsible for testing their end-product for any additional compliance

requirements required with this module installed.

Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour

utilisation de dispositif module)

1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre

l'antenne et les utilisateurs, et

2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne

seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son

produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.

IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or

co-location with another transmitter), then the Canada authorization is no longer considered valid

and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will

be responsible for re-evaluating the end product (including the transmitter) and obtaining a

separate Canada authorization.

NOTE IMPORTANTE:

Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations

d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du

Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans

ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur)

et l'obtention d'une autorisation distincte au Canada.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be installed

such that 20 cm may be maintained between the antenna and users. The final end product must be

labeled in a visible area with the following: “Contains IC:10293A-WMBNBM26A”.

Plaque signalétique du produit final

Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne

peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et

les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:

"Contient des IC: 10293A-WMBNBM26A ".

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to

install or remove this RF module in the user’s manual of the end product which integrates this

module.

The end user manual shall include all required regulatory information/warning as show in this

manual.

Manuel d'information à l'utilisateur final

L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à

la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui

Ma

n

u

el

l

d

'

'i

'

f

nf

f

o

rm

a

i

ti

i

o

n

à

l

'

'u

'

ti

i

li

i

li

sa

t

eu

r

f

i

in

i

al

l

L'

L

'

L

'

L

'

in

té

é

gr

g

r

at

eur

OE

O

OE

O

E

M

do

d

it

ê

tr

e cons

ci

i

en

t

de

d

ne

pa

p

s

fo

f

ur

ni

i

r

de

d

s

in

i

f

fo

f

rm

at

io

i

ns

à

l

'u

i

ti

i

li

l

i

l

i

l

i

sa

te

ur

f

i

in

i

l

al

l

q

ua

nt

à

la

f

açon

d

'

'i

ns

ta

l

ll

l

er ou

de

d

suppr

im

er ce mo

du

d

l

le

l

R

F

da

d

ns

l

e manu

el

l

d

e

l'

l

ut

i

il

i

l

is

i

at

eur

du

d

pro

du

d

i

it

f

in

i

al

l

q

ui

i

intègre ce module.

Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et

avertissements comme indiqué dans ce manuel.

Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that

the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point

operation as appropriate; and

(iii) Users should also be advised that high-power radars are allocated as primary users (i.e. priority

users) of the bands 5650-5850 MHz and that these radars could cause interference and/or damage

to LE-LAN devices.

Avertissement:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une

utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de

satellites mobiles utilisant les mêmes canaux;

(ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5 850 MHz) doit

être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à point et l’exploitation non

point à point, selon le cas;

(iii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute

puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes

5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux

dispositifs LAN-EL.

Universal Global Scientific WMBNBM26A 802.11b/g/n + BT Wireless LAN Module User Manual Unlock rev

Universal Global Scientific Industrial Co., Ltd. 802.11b/g/n + BT Wireless LAN Module Unlock rev

Contents

User Manual

Navigation menu

Namespaces

Views

Navigation