Universal Scientific CBGIN01 802.11G WLAN Card module User Manual I

Universal Scientific Industrial Co., Ltd. 802.11G WLAN Card module I

Manual

System Product Contract Mfg Business Division Draft User Manual for CB-G-IN-01, 03 Card BusSOURCE ORGANIZATION: USI COM/PDV/TPMPrepared by: Amos Date: Jun, 13, 2003Checked by: Approved by: Date: Concurrence: Date:
Universal Scientific Industrial Corp.. Doc No. Rev 1.0Document released by COM/PDV/TPM Date. 2003/06/13 Page 2Description Draft User manual for CB-G-IN-01, 03 CARD BusThe content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorizedi n writing by Universal Scientific Industrial Co. ,Ltd. Copyright © 2003 Universal Scientific Industrial Co. ,Ltd.Change SheetRev. DateDescription of change Approval & Date1.0 2003/6/13 Page All Initial
Universal Scientific Industrial Corp.. Doc No. Rev 1.0Document released by COM/PDV/TPM Date. 2003/06/13 Page 3Description Draft User manual for CB-G-IN-01, 03 CARD BusThe content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorizedi n writing by Universal Scientific Industrial Co. ,Ltd. Copyright © 2003 Universal Scientific Industrial Co. ,Ltd.OverviewThis document is for a user who wants to install CB-G-IN-01, 03 CARD Bus in Notebook/PCdesk , the user can read the document to configure his wireless PC Card.Software RequirementOS: Windows95,98,2K,NT,XPSoftware Package: USI_driver_11g_V1-0-8.zipHardware RequirementCB-G-IN-01, 03 CARD Bus.PC running in win95,98,2k,NT,XP .Cardbus controller in PC or PCMCIA interface in Notebook Installationz Install the driver in your host.z Insert PC Card in to the PC Card slot of host PC (Note: connect PC Card to PC Desk via adapterof pcmcia – cardbus) Execute the Configuration ProgramThere are two ways to start the configuration program.z After installation driver, insert the card into PC host, the program will be executed automatically,and display a tray icon
Universal Scientific Industrial Corp.. Doc No. Rev 1.0Document released by COM/PDV/TPM Date. 2003/06/13 Page 4Description Draft User manual for CB-G-IN-01, 03 CARD BusThe content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorizedi n writing by Universal Scientific Industrial Co. ,Ltd. Copyright © 2003 Universal Scientific Industrial Co. ,Ltd. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no changeto the antenna or the device is permitted. Any change to the antenna or thedevice could result in the device exceeding the RF exposure requirements andvoid user’s authority to operate the device.FCC INFORMATIONThe Federal Communication Commission Radio Frequency InterferenceStatement includes the following paragraph:The equipment has been tested and found to comply with the limits for a ClassB Digital Device, pursuant to part 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instruction, may causeharmful interference to radio communication. However, there is no grantee thatinterference will not occur in a particular installation. If this equipment dose cause
Universal Scientific Industrial Corp.. Doc No. Rev 1.0Document released by COM/PDV/TPM Date. 2003/06/13 Page 5Description Draft User manual for CB-G-IN-01, 03 CARD BusThe content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorizedi n writing by Universal Scientific Industrial Co. ,Ltd. Copyright © 2003 Universal Scientific Industrial Co. ,Ltd.harmful interference to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.--Consult the dealer or an experienced radio/TV technician for help.The user should not modify or change this equipment without written approval form U n i v e r s a lScientific Industrial Co., Ltd. .Modification could void authority to use thisequipment.
Universal Scientific Industrial Corp.. Doc No. Rev 1.0Document released by COM/PDV/TPM Date. 2003/06/13 Page 6Description Draft User manual for CB-G-IN-01, 03 CARD BusThe content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorizedi n writing by Universal Scientific Industrial Co. ,Ltd. Copyright © 2003 Universal Scientific Industrial Co. ,Ltd.Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct theinterference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that maycause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with minimum distance 20cmbetween the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter.
Universal Scientific Industrial Corp.. Doc No. Rev 1.0Document released by COM/PDV/TPM Date. 2003/06/13 Page 7Description Draft User manual for CB-G-IN-01, 03 CARD BusThe content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorizedi n writing by Universal Scientific Industrial Co. ,Ltd. Copyright © 2003 Universal Scientific Industrial Co. ,Ltd.This device is intended only for OEM integrators under the following conditions:1) The antenna must be installed such that 20 cm is maintained between the antenna andusers, and 2) The transmitter module may not be co-located with any other transmitter or antenna.As long as 2 conditions above are met, further transmitter test will not be required. However,the OEM integrator is still responsible for testing their end-product for any additionalcompliance requirements required with this module installed (for example, digital deviceemissions, PC peripheral requirements, etc.).IMPORTANT NOTE: In the event that these conditions can not be met (for example certainlaptop configurations or co-location with another transmitter), then the FCC authorization isno longer considered valid and the FCC ID can not be used on the final product. In thesecircumstances, the OEM integrator will be responsible for re-evaluating the end product(including the transmitter) and obtaining a separate FCC authorization.End Product LabelingThis transmitter module is authorized only for use in device where the antenna may beinstalled such that 20 cm may be maintained between the antenna and users ( for example :access points, routers, wireless ADSL modems and similar equipment ). The final endproduct must be labeled in a visible area with the following: “Contains TX FCC ID:IXMCBGIN01 ”.Manual Information That Must be IncludedThe OEM integrator has to be aware not to provide information to the end user regarding how toinstall or remove this RF module in the users manual of the end product which integrate thismodule.The users manual for OEM integrators must include the following information in aprominent location “ IMPORTANT NOTE: To comply with FCC RF exposure compliancerequirements, the antenna used for this transmitter must be installed to provide a separationdistance of at least 20 cm from all persons and must not be co-located or operating inconjunction with any other antenna or transmitter.
Universal Scientific Industrial Corp.. Doc No. Rev 1.0Document released by COM/PDV/TPM Date. 2003/06/13 Page 8Description Draft User manual for CB-G-IN-01, 03 CARD BusThe content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorizedi n writing by Universal Scientific Industrial Co. ,Ltd. Copyright © 2003 Universal Scientific Industrial Co. ,Ltd.Technical SupportTechnical Contact :Universal Scientific Industrial Co., Ltd. ( Headquarters )Address : 135, Lane 351, Taiping Rd., Sec. 1, Tsao Tuen, Nan Tou, TaiwanUSI Taipei Office : 10F, 420, Keelung Road, Sec. 1, Taipei, TaiwanContact Person : Ray HuangTelephone : +886-2-2345-5006, Ext.119Fax : +886-2-2345-5191Email : rayhwang@ms.usi.com.twTechnical Contact in the US :Address : 685A Jarvis Drive, Morgan Hill, CA 95037, USATelephone : +1-408-776-1966Fax : +1-408-778-5509Website : www.usi.com.tw

Navigation menu