Universal Security Instruments Usi 5204 Users Manual ManualsLib Makes It Easy To Find Manuals Online!

: Universal-Security-Instruments Universal-Security-Instruments-Usi-5204-Users-Manual-121723 universal-security-instruments-usi-5204-users-manual-121723 universal-security-instruments pdf

Open the PDF directly: View PDF .
Page Count: 8

READ ALL INSTRUCTIONS

The smoke alarm has a recommended service life of at least 10 years under normal conditions.

The smoke alarm uses an extremely small amount of a radioactive element in the ionization

chamber. Do not tamper with radioactive sealed source or try to repair the smoke alarm

yourself. Refer to instructions for repairs.

MODEL USI-5204

(Part #USI-5204HA)

COMMERCIAL RESIDENTIAL (UTHA)

SMOKE & FIRE ALARM WITH SILENCE CONTROL

SMOKE ALARM LIMITATIONS AND FUNCTIONS

• THERE ARE TWO BASIC SMOKE ALARM TYPES - IONIZATION AND PHOTOELECTRIC.

Ionization smoke alarms are your best overall choice for reliability and fast response time,

since they quickly sense small "invisible" smoke particles and will also sense larger "visible"

smoke particles. Photoelectric smoke alarms may respond more quickly in certain types of

fires, for example - slow smoldering fires with large "visible" smoke particles. ALL TYPES OF

SMOKE ALARMS HAVE LIMITATIONS. NO TYPE OF SMOKE ALARM CAN SENSE EVERY

KIND OF FIRE OR SMOKE EVERY TIME.

• WARNING - SMOKE ALARMS WILL NOT WORK DURING A LOSS OF POWER. SINCE A SMOKE

ALARM WILL NOT WORK WITHOUT POWER, having an alarm(s) that works from two completely

different power sources, such as an AC direct wire with battery backup smoke alarm, can give you an

extra measure of protection in case of an AC power failure or a dead battery.

• USING A SMOKE ALARM IN A SMOKY AREA LIKE A KITCHEN, OR IN A HIGH HUMIDITY

AREA NEAR A SHOWER, CAN CAUSE FALSE ALARMS. DO NOT TURN OFF THE AC

POWER TO QUIET THE ALARM. A SMOKE ALARM WILL NOT HELP PROTECT YOU IF IT

IS NOT POWERED. Properly locate your alarm to avoid nuisance alarms.

• A SMOKE ALARM MAY NOT ALWAYS WARN YOU ABOUT FIRES CAUSED BY CARELESSNESS

AND SAFETY HAZARDS LIKE SMOKING IN BED, VIOLENT EXPLOSIONS, ESCAPING GAS,

IMPROPER STORAGE OF FLAMMABLE MATERIALS, OVERLOADED ELECTRICAL CIRCUITS,

CHILDREN PLAYING WITH MATCHES, NATURAL CAUSES SUCH AS LIGHTNING, OR ARSON.

FIRE PREVENTION IS YOUR BEST SAFEGUARD.

• INSTALLING SMOKE ALARMS MAY MAKE YOU ELIGIBLE FOR LOWER INSURANCE

RATES, but SMOKE ALARMS ARE NOT A SUBSTITUTE FOR INSURANCE. Homeowners

and renters alike should continue to insure their lives and properties.

• SMOKE ALARMS CANNOT WORK WITHOUT POWER. Battery operated units cannot work if the

batteries are missing, disconnected or dead, if the wrong type of batteries are used or if the batteries

are not installed correctly. AC (only) powered units cannot work if the AC power is cut off for any

reason. If you are concerned about the limitations of battery or AC power, install both types of units.

• SMOKE ALARMS CANNOT DETECT FIRES IF THE SMOKE DOES NOT REACH THEM.

Smoke from fires may not reach the sensing chamber and set off the alarm. One unit should

be installed inside each bedroom or sleeping area.

• SMOKE ALARMS MAY NOT DETECT FIRE ON ANOTHER FLOOR OR AREA OF THE

HOME. Recommended minimum protection is at least one unit in every sleeping area and

every bedroom on every level of your home. Interconnected units may provide earlier warning

than stand-alone units since all units alarm when one detects smoke.

• SMOKE ALARMS MAY NOT BE HEARD. The alarm horn in this unit meets or exceeds current

standards, but it may not be heard if: (1) the unit is located outside a closed or partially closed

door; (2) residents recently consumed alcohol or drugs; (3) the alarm is drowned out by noise

from stereos, TV's, air conditioners or other appliances or (4) if residents are hearing impaired

or sound sleepers.

• SMOKE ALARMS ARE NOT FOOLPROOF. You must test the unit weekly to ensure your

continued protection. Smoke alarms cannot prevent or extinguish fires.

• SMOKE ALARMS HAVE A LIMITED LIFE. The unit should be replaced immediately if it is not

operating properly. You should always replace a smoke alarm after 10 years.

• SMOKE ALARMS ARE NOT TO BE USED WITH DETECTOR GUARDS UNLESS THE

COMBINATION HAS BEEN EVALUATED AND FOUND SUITABLE FOR THAT PURPOSE.

• CURRENT STUDIES HAVE SHOWN SMOKE ALARMS MAY NOT AWAKEN ALL SLEEPING

INDIVIDUALS AND THAT IT IS THE RESPONSIBILITY OF INDIVIDUALS IN THE

HOUSEHOLD WHO ARE CAPABLE OF ASSISTING OTHERS TO PROVIDE ASSISTANCE

TO THOSE WHO MAY NOT BE AWAKENED BY THE ALARM SOUND OR TO THOSE

WHO MAY BE INCAPABLE OF SAFELY EVACUATING THE AREA UNASSISTED.

USI-5204

Visit Us on the Web! www.SmokeAlarms.com

Page 2

RECOMMENDED LOCATION OF ALARMS

• Locate the first smoke alarm in the immediate area of the bedrooms. Try to protect the escape

route as the bedrooms are usually farthest from an exit. If more than one sleeping area exists,

locate additional smoke alarms in each sleeping area. If a hall is more than 40 feet (12 meters)

long, install a smoke alarm at each end.

• Locate additional smoke alarms to protect any stairway as stairways act like chimneys for

smoke and heat.

• Locate at least one smoke alarm on every floor level.

• Locate a smoke alarm in any area where a smoker sleeps or where electrical appliances are

operated in sleeping areas.

• Smoke, heat and other combustion products rise to the ceiling and spread horizontally. Mounting

the smoke alarm on the ceiling in the center of the room places it closest to all points in the room.

Ceiling mounting is preferred in ordinary residential construction. However, in mobile homes, wall

mounting on an inside partition is preferred to avoid the thermal barrier that may form at the

ceiling.

• When mounting smoke alarm on the ceiling, locate it a minimum of 4" (10cm) from a side wall

or corner (see Diagram A).

• When mounting smoke alarm on a wall, if local codes allow, use an inside wall with the top edge

of the smoke alarm a minimum of 4" (10cm) and a maximum of 12" (30.5cm) below the ceiling/

wall intersections (See Diagram A).

Sloped Ceilings (Peaked Ceilings):

Smoke alarms or smoke detectors mounted on a peaked ceiling shall be located within 36 in. (914 mm) horizontally

of the peak, but not closer than 4 in. (102 mm) vertically to the peak.

Sloped Ceilings (Shed Ceilings):

Smoke alarms or smoke detectors mounted on a sloped ceiling having a rise greater than 1 ft. in 8 ft. (1 m in 8

m) horizontally shall be located within 36 in. (914 mm) of the high side of the ceiling, but not closer than 4 in. (102

mm) from the adjoining wall surface.

Tray-Shaped Ceilings:

Smoke Alarms or smoke detectors shall be installed on the highest portion of the ceiling or on the sloped portion

of the ceiling within 12 in. (305 mm) vertically down from the highest point.

Mobile Home Installation:

For minimum protection, smoke alarms should be installed in compliance with H.U.D. Manufactured Home

Construction Safety Standards, Title 24 CFR, Section 3280.208 and Section 3282. For additional protection, see

Single Story Residence smoke alarm requirements/recommendations for Existing Homes and New Construction

Homes.

Note: For mobile homes built before 1978, install smoke alarms on inside walls between 4” and 12” from the

ceiling (older mobile homes have little or no insulation in the ceiling). This is especially important if the ceiling

is unusually hot or cold.

Install a smoke alarm inside each bedroom and in the hallway outside each separate sleeping area.

Existing Homes:

The NFPA requires a smoke alarm on every level and outside each sleeping area in existing construction. An

existing household with one level and one sleeping area is required to have one smoke alarm.

New Construction Homes and Manufactured Homes:

The NFPA requires AC-powered, interconnected smoke alarms to be installed inside each bedroom, outside each

bedroom area, and on every level of the home. They also require a minimum of two AC-powered, interconnected

smoke alarms in any new construction home.

THIS SMOKE ALARM WILL NOT WORK WITHOUT 120 VAC POWER AND A

GOOD BATTERY PROPERLY INSTALLED. THE SMOKE ALARM SHOULD BE

TESTED WHEN INSTALLED AND THEN TESTED WEEKLY AFTER THAT.

FALSE ALARMS

The smoke alarm is designed to minimize false alarms. Smoking will not normally set off the alarm

unless smoke is blown directly into the smoke alarm. Combustion particles from cooking may set

off the alarm if the smoke alarm is located close to the kitchen cooking surface. Large quantities of

combustion particles are generated from spills or broiling.

If the smoke alarm does sound, check for fires first. If a fire is discovered, get out and call the fire

department. If no fire is present, check to see if one of the reasons listed above may have caused

the alarm. Use the "silence" feature if it is a false alarm.

INSTALLATION AND OPERATION

INSTALLATION INSTRUCTIONS: CAUTION!! READ CAREFULLY.

CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOVABLE!

• A mounting plate is provided on the back of the alarm.

• Remove the mounting plate from the back of the alarm by holding the mounting plate and twisting

the alarm in the direction indicated by the "TURN TO REMOVE" arrow on the side of the alarm

base.

Installation of this unit must conform to the electrical codes in your area; Article 760 of the

National Electrical Code, NFPA 72, 101; SBC (SBCCI); UBC (ICBO); NBC (BOCA): OTFDC

(CABO), and any other local or building codes that may apply. Wiring and installation must

be performed by a licensed electrician. Failure to follow these guidelines may result in injury

or property damage.

This unit must be powered by a 24-hour, 120V AC 60Hz circuit. Be sure the circuit cannot be

turned off by a switch, dimmer or ground fault circuit interrupter. Failure to connect this unit

to a 24-hour circuit may prevent it from providing constant protection.

IMPORTANT: Do not subject this smoke alarm to megger, high voltage or high-pot tests.

Remove the smoke alarm(s) before high-potting tests occur on the circuit or system.

(Ref. Section 550-17, National Electric Code, 2002 Edition).

ELECTRICAL SHOCK HAZARD

Turn off power to the area where you will install this unit at the circuit breaker or fuse box

before beginning installation. Failure to turn off the power before installation may result in

serious electrical shock, injury or death.

TAMPER LOCKING PIN: To make your alarm somewhat tamper resistant, a locking pin has been

provided (break-away part of mounting plate). Using this tamper pin will deter children and others

from removing the alarm from the mounting plate. To use the tamper pin, insert it into the hole in the

side of the alarm after the alarm has been installed on the mounting plate. Using long nose pliers,

pull the tamper pin out of the hole. It is now possible to remove the alarm from the mounting plate.

1. Turn the alarm counterclockwise in the direction indicated by the "TURN TO REMOVE" arrow

on the side of the alarm base to remove it from the mounting plate. NOTE: The alarm is sealed

and the cover is not removable.

Page 3

AVOID THESE LOCATIONS

• the garage – products of combustion are present when you start your automobile.

• near appliances or areas where normal combustion regularly occurs (kitchens, near furnaces,

gas hot water heaters). Use smoke alarms with Silence Control for these areas.

• in areas with high humidity, like bathrooms or areas near dishwashers or washing machines.

Install at least 3 feet (0.9 meters) away from these areas.

• in areas of turbulent air such as air returns or heating and cooling supply vents, smoke alarms

shall not be located where airflow prevents operation of the alarms.

• in extremely dusty, dirty or insect-infested areas. Loose particles interfere with smoke alarm

operation.

• in areas where temperature may fall below 400F (4.40C) or rise above 1000F (37.80C).

• closer than 1 foot (0.3m) from fluorescent lights, electrical "noise" and flickering may affect the

alarm's operation.

• closer than 3 feet (0.9m) horizontal path from the tip of the blade of a ceiling suspended (paddle)

fan.

• on a poorly insulated ceiling or exterior wall (mount smoke alarm on an inside wall).

2. Wiring Instructions:

a. The appropriate power supply is 120 Volt single phase power supplied from a non-switchable

circuit NOT protected by a ground fault circuit interrupter.

b. Turn off main power to the circuit before wiring the smoke alarm.

c. There are three pigtail leads (black, white and yellow) coming from the AC QUICK

CONNECTOR. The proper wire connection is as follows:

WIRES FROM QUICK CONNECTOR CONNECT TO

BLACK "HOT" side of AC line

WHITE "NEUTRAL" side of AC line

YELLOW Interconnect wires of other units

Early warning fire detection is best achieved by the installation of fire detection equipment in

all rooms and areas of the household as follows: A smoke alarm installed in each separate

sleeping area (in the vicinity of, but outside of, the bedrooms) and heat or smoke alarms in

living rooms, dining rooms, kitchens, hallways, attics, furnace rooms, closets, utility storage

rooms, basements and attached garages. Test the smoke alarm weekly to assure proper

operation.

3. Attach the mounting plate to the electrical junction box.

4. To activate 9 volt battery and alarm, hold the QUICK DRAW(R) battery drawer closed, pull and

remove the PULL-TAB. Discard PULL-TAB.

5. Plug the AC QUICK CONNECTOR into the alarm base. Push and turn the alarm clockwise

onto the mounting plate.

6. See "TAMPER LOCKING PIN."

For units that are used as single smoke alarms, do not connect the yellow wire to anything. Insulate

this wire (tape it) in place to make certain the yellow wire cannot contact any metal parts.

Interconnected units can provide earlier warning of fire than stand-alone units, especially if

a fire starts in a remote area of the dwelling. This smoke alarm may be interconnected with

as many as 11 other USI ELECTRIC model smoke alarms such as USI-1103, USI-1203, USI-

1204, USI-1209, USI-1213, USI-2204, USI-3204 and 6 other units which may be a combination

of Carbon Monoxide Alarms such as USI-7385, USI-7390, USI-7485, USI-7490, USI-7795, Heat

Alarms/USI-2430 or Relay Modules/USI-960 for a total of not more than 18 interconnected

devices.

Interconnected CO alarms will only respond if a CO alarm / event initiates the alarm. All other

alarms remain silent.

Interconnected smoke alarms, heat alarms and relay modules will only respond if a smoke

alarm / event or heat alarm / event initiates the alarm. All CO alarms remain silent.

Note that units without battery backup will not respond during an AC power failure.

NOTE: Relay Modules/USI-960 will not respond if a CO alarm / event initiates the alarm.

Page 4

The yellow wire is used only for multiple station operation with USI ELECTRIC Model alarms

only. Connecting this yellow wire to any other circuits may result in damage. When alarms

are interconnected, all units must be powered from a single AC branch circuit. If local codes

do not permit be sure the neutral wire is common to both phases. The maximum wire run

distance between the first and last alarm/device in an interconnected system is 1,000 feet.

NOTE: Use standard household wire (18 gauge or larger, rated at least 300V, as required by

local codes) available at all electrical supply/hardware stores.

The wiring to be used shall be in accordance with the provisions of Articles 210 and 300.3(B)

of the National Electrical Code, ANSI/NFPA 70. In addition, the resistance of the interconnecting

wiring shall be a maximum of 10 Ohms.

INPUT:

120 VAC

60 HZ

.05A

7. Turn on AC power and check the LED's for proper operation. The green LED lights to indicate

AC power. The red LED will flash every 40-60 seconds to indicate proper operation.

OPERATION, TESTING & MAINTENANCE

OPERATION: The smoke alarm is operating once the power is connected and turned on (the battery

must also be installed). When products of combustion are sensed, the unit sounds a loud alarm

which continues until the air is cleared.

This alarm incorporates the internationally recognized horn signal for evacuation. During alarm

mode, the horn produces three short beeps followed by a two second pause and then repeats.

STANDBY CONDITION: The red LED flashes once every 40-60 seconds to indicate the unit is

properly functioning.

LOCAL ALARM CONDITION: The red LED flashes rapidly and the unit emits a loud, pulsating

alarm sound.

REMOTE ALARM CONDITION: The red LED is off and the unit emits a loud, pulsating alarm.

GREEN LED: The green LED is on whenever AC power is turned on.

TESTING: Test by pushing the test button on the smoke alarm cover until the alarm sounds, then

release. The alarm sounds if all electronic circuitry, horn and battery are working. The alarm may

continue to sound for up to 10 seconds after the button is released. If no alarm sounds, the unit may

have a defective battery or other failure. Test the smoke alarm weekly to assure proper operation.

If you choose to use an aerosol smoke product to test the smoke alarm, be certain to use one

that has been Listed to Underwriters Laboratories, Inc. Safety Standards and use it only as

directed. Use of non-UL Listed products or improper use of UL Listed products may affect

the smoke alarm's sensitivity.

FALSE ALARMS "SILENCE" CONTROL: Units with the "silence" feature have the capability of

temporarily reducing the sensitivity of the alarm circuit for approximately 3-9 minutes. This feature is

to be used only when a known alarm condition such as smoke from cooking activates the smoke

alarm. The smoke alarm "silence" feature is activated by pushing the Hold to Silence button on the

smoke alarm cover for at least three seconds. The smoke alarm will automatically reduce sensitivity

and the red LED will light for approximately 3-9 minutes to indicate the alarm is in the temporary

silent condition. The smoke alarm will gradually regain normal sensitivity and sound the alarm if

particles of combustion are still present. The "silence" feature may be used repeatedly until the air

has cleared.

Page 5

NEVER use an open flame of any kind to test this unit. You might accidentally damage or set

fire to the unit or to your home. The built-in test switch accurately tests the unit's operation

as required by Underwriters Laboratories Inc. (UL).

(UTHA) Sensitivity Indicating Means

The sensitivity indicating means for this Smoke and Fire Alarm is the use of the analyzer for Smoke

Detectors Model 501-A or 501-A/Bat Aerosol Generator Manufactured by Gemini Scientific Corp.,

1122-B Aster Ave., Sunnyvale, CA 94086.

The Equivalent UL 268 Light obscuration %/Ft as measured by this instrument must be between

1.55% Obs./Ft. and 0.85% Obs./Ft (1.20 + 0.35% Obs./Ft.).

(UTHA) Go/No-Go Field Test

The Go/No-Go test for this Smoke and Fire Alarm is the use of a UL Listed can type aerosol smoke

detector tester. The instructions for the use of this tester are given on the container.

BACKUP BATTERY REPLACEMENT

Disconnect AC power before changing battery. Shock hazard exists if AC power is miswired.

The smoke alarm uses a 9 Volt battery. The battery should last for at least one year under normal

operating conditions. The smoke alarm has a low battery indicator, an audible "beep." It will operate

at 30-40 second intervals for a minimum of 7 days. When this indication occurs, replace the battery

with an Alkaline type (Eveready Energizer #522, Duracell #MN1604), Carbon-Zinc type (Gold Peak

#1604P, Eveready #216). Use the convenient QUICK DRAW(R)

pull-out batterydrawer for easy battery

replacement.

Pull the QUICK DRAW(R) battery drawer open and remove the battery. While observing polarity,

push the replacement battery into the battery drawer until it is held securely in place. Carefully close

and latch the battery drawer.

REPAIRS AND SERVICES

The smoke alarm contains less than 1 microcurie (37 kilobecquerel) of Americium 241, a radioactive

material. The distribution of these ionization-type smoke alarms is licensed by the U.S. Nuclear

Regulatory Commission; the consumer is exempt from any licensing or requirements. If the

smoke alarm is defective in any way, do not tamper with the unit. Return the unit for servicing. (See

warranty for instructions or in-warranty returns.) There will be a service charge for repairing out of

warranty units.

Page 6

Before using the alarm "silence" feature, identify the source of smoke and be certain that

safe conditions exist.

(UTHA) MAINTENANCE:

The smoke alarm is virtually maintenance free. However, under dusty conditions, a vacuum hose

may be used to clear the sensing chamber of dust.

Clean the smoke alarm at least once a month to remove dust, dirt or debris. Always turn off power

to smoke alarm before cleaning. Using a soft brush or wand attachment to a vacuum cleaner,

vacuum all sides and cover of smoke alarm. Be sure all the vents are free of debris.

If the smoke alarm is false alarming and cannot be restored to normal operation, the smoke alarm

should be replaced.

DEVELOP AND PRACTICE A PLAN OF ESCAPE

BASICS OF ESCAPE PLAN

o Make a floor plan indicating all doors and windows and at least two escape routes from each

room. Second story windows may need a rope or chain ladder.

o Have a family meeting and discuss your escape plan, showing everyone what to do in case of

fire.

o Determine a place outside your home where all of you can meet if a fire occurs.

o Familiarize everyone with the sound of the smoke alarm and train them to leave your home when they

hear the sound.

o Identify children's bedrooms with red stickers placed in the upper left corner of the windows. They

are available from your local fire department.

o Practice a fire drill at least every six months. Practice allows you to test your plan before an

emergency. You may not be able to reach your children. It is important they know what to do!

WHAT TO DO WHEN THE ALARM SOUNDS

o Leave immediately by your plan of escape. Every second counts, so don't waste time getting

dressed or picking up valuables.

o In leaving, don't open any inside door without first feeling its surface. If hot, or if you see smoke

seeping through cracks, don't open that door! Instead, use your alternate exit. If inside door is

cool, place your shoulder against it, open it slightly and be ready to slam it shut if heat and smoke

rush in.

o Stay close to the floor if air is smoky. Breathe shallowly through a cloth, wet if possible.

o Once outside, go to your selected meeting place and make sure everyone is there.

o Call the fire department from your neighbor's home – not from yours!

o Don't return to your home until fire officials say that it is all right to do so.

NATIONAL FIRE PROTECTION ASSOCIATION REQUIRED PROTECTION

For your information, the National Fire Protection Association's Standard 72, reads as follows:

“11.5.1 One- and Two-Family Dwelling Units. 11.5.1.1 Smoke Detection.

Where required by applicable laws, codes, or standards for the specified

occupancy, approved single- and multiple-station smoke alarms shall be

installed as follows: (1) In all sleeping rooms. Exception: Smoke alarms

shall not be required in sleeping rooms in existing one- and two-family

dwelling units. (2) Outside of each separate sleeping area, in immediate

vicinity of the sleeping rooms. (3) On each level of the dwelling unit, including

basements. Exception: In existing one- and two-family dwelling units,

approved smoke alarms powered by batteries are permitted.

“A.11.8.3 Are More Smoke Detectors Desirable? The required number of

smoke detectors might not provide reliable early warning protection for those

areas separated by a door from the areas protected by the required smoke

detectors. For this reason, it is recommended that the householder consider

the use of additional smoke detectors for those areas for increased

protection. The additional areas include the basement, bedrooms, dining

room, furnace room, utility room, and hallways not protected by the required

smoke detectors. The installation of smoke detectors in kitchens, attics

(finished or unfinished), or garages is not normally recommended, as these

locations occasionally experience conditions that can result in improper

operation.”

The equipment should be installed using wiring methods in accordance with the National

Fire Protection Association’s Standard 72, Chapter 11. (National Fire Protection

Association, Batterymarch Park, Quincy, MA 02269).

THIS PRODUCT IS LISTED TO UL STANDARD FOR SAFETY,

UL217 BY UNDERWRITERS LABORATORIES

Page 7

288-3297-00D/UTHA

USI FIVE YEAR LIMITED WARRANTY

USI ELECTRIC, INC. ("USI") warrants your USI product to be free

from defects in material and workmanship for a period of five (5)

years from the date of purchase. This warranty applies only to the

original consumer purchaser and only to products used in normal

residential use and service. If this product is found to be defective, USI's

only obligation, and your exclusive remedy, is the repair or replacement

of the product, at USI's discretion, provided that the product has not

been damaged through misuse, abuse, accident, modifications, alteration,

neglect or mishandling. This Warranty shall not apply to any product

which is found to have been improperly installed, set-up, or used in any

way not in accordance with the instructions supplied with the product.

This warranty shall not apply to any batteries used in the product or to

any damage which may be caused by such batteries. For repair or

replacement, send the defective product to USI ELECTRIC, INC. at

11407 Cronhill Drive, Suite A, Owings Mills, Maryland 21117, postage

prepaid with a payment of $5.00 to cover the costs of return postage

and handling. You must include a proof of purchase (receipt) along with

the returned product.

USI DOES NOT WARRANT AND SPECIFICALLY DISCLAIMS ANY

WARRANTY, WHETHER EXPRESS OR IMPLIED, OF FITNESS FOR

A PARTICULAR PURPOSE, OTHER THAN THE WARRANTY

CONTAINED HEREIN. NO IMPLIED WARRANTY ON THIS PRODUCT,

CREATED BY STATE LAW, SHALL EXTEND BEYOND THE TERM OF

THIS WARRANTY UNLESS SUCH LAW OTHERWISE PROVIDES. USI

SPECIFICALLY DISCLAIMS ANY LIABILITY AND SHALL NOT BE

LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL LOSS OR

DAMAGE, INCLUDING, BUT NOT LIMITED TO, DAMAGES TO ANY

EQUIPMENT WITH WHICH THIS PRODUCT IS USED.

Some states do not allow the exclusion or limitation of incidental or

consequential damages so the above limitations or exclusions may not

apply to you.

No agent, representative, dealer, or employee of the company has the

authority to increase or alter the obligations or terms of this Warranty.

This Warranty gives you specific legal rights and you may also have

other rights which vary from state to state.

This Warranty is only valid for merchandise purchased from outlets in

the United States and Canada.

©2002 UNIVERSAL SECURITY INSTRUMENTS, INC.

Printed in China

11407 Cronhill Drive, Suite A

Owings Mills, Maryland 21117 USA

Visit Us on the Web! www.SmokeAlarms.com