Universal Surveillance Systems USS-POWER4-B00 Power 4 System User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1267000
Application ID	CEGJibUiuHL+n6tguQ7mcQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.31kB (266400 bits)
Date Submitted	2010-04-14 00:00:00
Date Available	2010-04-14 00:00:00
Creation Date	2010-01-18 10:03:37
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2010-01-18 10:03:40
Document Title	Users Manual
Document Creator	Acrobat PDFMaker 8.1 for Word

User’s Guide
Innovative Security Solutions
USS POWER OF 4™
Contents
•
•
•
•
•
•
•
•
About this Guide
Limitation of Warranty
System Overview
Materials Required
Installation Requirements
Set up Procedure
Specifications
Declarations
About this Guide
This User’s Guide provides functional overview of the
Power of 4™ along with the Installation Requirements and
Setup Procedure for the User.
Limitation of Warranty
Any deviations from the materials or procedures
specified herein shall void the warranty of Universal
Surveillance System with the owner/buyer. In no event shall
Universal Surveillance Systems be liable for loss or damage
caused by the use of materials or procedures that do not
meet the specifications of Universal Surveillance Systems.
USS Products\Power of 4™\User’s Manual
Page 1
System Overview
The Power of 4™ is an advanced EAS System with early detection tools. It provides four
levels of security, which include:
•
•
•
•
EAS Technology: The System has advanced Acousto-Magnetic Technology detection
designed to detect 58 KHz hard tags and labels. Audible and visual alarms are provided
for the detection.
Booster Bag/Foil Lined Bag Detection: The System includes an early detection
system that triggers an alarm when a Booster Bag/Foil Lined Bag is detected. Once the
Booster Bag/Foil Lined Bag is detected within the detection range, the system alerts
store personnel via one or several optional notification devices.
Magnet Detection: The third level of security allows the Power of 4™ to detect when
Magnetic Detachers are illegally brought into the store.
Anti-Jamming Circuit: The Power of 4™ has an intelligent anti-jamming feature which
detects EAS jamming devices affecting the Power of 4™ System.
Materials Required
For all Power of 4™ installations, the following materials should be prepared prior to an
install, in addition to basic required tools and parts:
•
•
•
•
•
•
•
•
Cables – 45 ft maximum length (to connect pedestals with control box )
USB Dongle (to establish connection between control box and computer)
Ethernet Cable and Connector Unit (to establish Internet connection, if applicable)
Computer or Laptop (should be loaded with ‘AM Application’ Software)
CAT5 Cables (to extend alarm outputs for Voice Annunciation purpose)
2 Low Power Transformers, 15 VAC (for Booster and Magnet Detection Systems)
Booster Bag/Foil Lined Bag, Magnetic Detacher, AM Tags, and Jammer Device (to be
used for testing purpose)
Digital Multimeter
Installation Requirements
It is strongly recommended that a Site Survey is performed prior to the actual
installation. The Survey should include pictures, actual measurements and special notes about
the location. The survey enables the installer/technician to select a good location for system
installation. In addition to a Site Survey, the installer/technician should also consider the
following requirements:
•
Verify that all equipments, tools and parts have arrived in good condition, and be able to
select a proper system configuration for the installation site.
USS Products\Power of 4™\User’s Manual
Page 2
Figure 1. USS Power of 4™
•
Check the Store’s electrical supply: There should be a minimum of 4 outlets for the AM
Control Box while the Electrical Line should be a dedicated 110V AC @ 60Hz. Neutral to
ground voltage check should be a maximum of 0.5 VAC.
WARNING!
Do not install this product in hazardous
areas where highly combustible or
explosive products are stored or used.
•
WARNING—RISK
ELECTRIC SHOCK!
OF
The AC power line could be carrying
110VAC.
The Location of the Power of 4™ control box should be at maximum of 45 "cable" ft
length from each pedestal. Shorter lengths are preferred and will contribute to better
response of the system.
USS Products\Power of 4™\User’s Manual
Page 3
•
Ensure good detection of all subsystems (EAS System, Booster Bag/Foil Lined Bag
System, Magnet and Jammer Detector) before mounting pedestals to the ground.
Spacing between pedestals should be from 5 to 6 ft and keeping appropriate distance
between pedestals and doors. Power cables, computers, mirrors, and other big metal
objects may affect the system operation so it is advisable to keep the pedestals away
from these materials as much as possible.
•
Bolt the pedestals to the floor and install the cables. Pull cords should be provided in the
conduit/wire trench from each pedestal location to adjacent pedestals, and from each
pedestal to the control box location.
•
Conduit/wire trench from each pedestal will carry four (4) CAT5 low voltage signal and
sync cables; the cables should originate from each pedestal and terminate near the
dedicated line outlets. All pedestals can share a common conduit/wire trench, but it
should be big enough to accommodate the increased number of cables.
Set up Procedure
•
Check for correct connections of all the cables before turning the EAS System power
ON.
•
Establish the connection between the Control Box and Computer (or laptop) using a
USB Dongle.
•
Load the AM Application Software; then, connect the system with software by searching
for an appropriate COM Port.
•
Set up the configuration using the software; select a proper system configuration from 8
available options (from the drop down menu) that you wish to install and confirm it by
clicking ‘Set Config’. According to the chosen configuration, a picture with description of
individual transmit and receive pedestal will be displayed on the computer screen.
•
Check the correct tuning of TX antennas and adjust the jumpers of the tuning capacitor
board “TX_CAPS” for fine-tuning of TX loop into resonance, if necessary.
•
Factory setting of TX1 and TX2 power is 200, which is the maximum specified limit for
the transmitter power.
•
Check for good synchronization with other systems (window “Sync”) from surroundings.
If interference is seen, use “Auto Sychro” to synchronize the system with surrounding
AM Systems automatically. To activate this function, it is necessary to start loading the
signals from surroundings (use ‘Automatic Read’ and ‘Hold Maximum’ set up) and wait
for at least twenty patterns to be loaded, and then click “Auto Synchro”.
USS Products\Power of 4™\User’s Manual
Page 4
•
If soft labels are used, RX ‘Sweep’ is recommended to be set to ON. Set RX ‘Sweep’
OFF if only hard tags are used.
•
Set the sensitivity of receivers (window “RX”). Gain is correct, if window "input level"
shown on the computer screen is in green or green/yellow. Gain is acceptable, if "input
level" is in yellow. If "input level" is in red, it is recommended to decrease the gain for the
RX channel. Factory setting is 9 for optimal receiver sensitivity. Test the detection using
all types of tags and labels in all 3 positions to check the receiver sensitivity.
•
If the detection is not acceptable, modify the RX detection criteria as Standard
Detection, Best Detection, etc....
•
Set up sound and light alarms (type of beeping, time duration, etc...).
•
Test jammer detection using a test jammer.
•
Set up and test the Internet connection between the system installation site and service
office (if remote monitoring is used).
•
Turn ON the power supply for Booster Bag/Foil Lined Bag System by plugging in the 15
VAC Power Transformer.
•
Choose the Booster transmit frequency from available 4 frequencies. Set up different
Booster transmit frequencies when installing more Booster transmitters near each other.
The Minimum distance for using the transmitters with same frequency is 10 meter. The
minimum distance also depends on surroundings at the place of installation.
•
Check the level of TX power of Booster Bag/Foil Lined Bag detector and adjust it if
necessary. Maximum allowable power setting is 100%.
•
Test the Booster Bag/Foil Lined Bag detection using the test Booster Bag/Foil Lined
Bag. The Booster Bag/Foil Lined Bag receiver can also be set to block the alarms
triggered by heavy metal objects such as shopping carts, baby strollers and trolleys.
Adjust the “CADDY” to block such alarms.
•
Turn ON the power supply for Magnet Detector by plugging in the 15 VAC Power
Transformer.
•
Test the Magnet Detector using a test magnet. Adjust the sensitivity “SENS” of the RX
Magnet Detector board, if needed.
•
Perform a final test on the Power of 4™ system (EAS, Booster Bag/Foil Lined Bag,
Magnet and Jammer Detector) before wrapping up installation process.
•
Observe the Power of 4™ system for several minutes and re-tune the system if
necessary.
USS Products\Power of 4™\User’s Manual
Page 5
Specifications
•
•
•
•
•
•
•
•
Primary Input: 100-120 VAC @60Hz
Input Power: 150W
Operating Frequency: 58KHz (±200Hz)
Transmitter: 2 multiplexed output channels
Receiver: 4 multiplexed input channels
Operating Temperature: 32° to 122°F (0° to 50°C)
2 Pedestals: 6-12 ft coverage (Pedestal seperation at 5-6 ft)
Dimensions: a. Pedestal: 61”H x 19.5” W x 4” D
b. Control Box: 4”H x 16” W x 11”D
Declarations
FCC Compliance: This Device has been tested and found to comply with the limits for a class
A device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a commercial installation. This equipment generates,
uses and can radiate radio frequency energy and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. The user is cautioned
that changes and modifications made to the equipment without the approval of manufacturer
could void the user’s authority to operate this equipment.
USS Products\Power of 4™\User’s Manual
Page 6

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Company                         : 
Source Modified                 : D:20100118180325
Creator Tool                    : Acrobat PDFMaker 8.1 for Word
Modify Date                     : 2010:01:18 10:03:40-08:00
Create Date                     : 2010:01:18 10:03:37-08:00
Metadata Date                   : 2010:01:18 10:03:40-08:00
Document ID                     : uuid:aa0307b6-48f6-46c9-a42a-ac14b0f71d54
Instance ID                     : uuid:0e571c75-71f3-457d-a932-9cb36fd989b8
Subject                         : 2
Format                          : application/pdf
Creator                         : 
Title                           : 
Page Count                      : 6
Page Layout                     : OneColumn
Author                          : 

EXIF Metadata provided by EXIF.tools