Utel UT-1100B Car Alarm User Manual Operational Manual
Utel Co. Ltd. Car Alarm Operational Manual
Utel >
Operational Manual
TWO WAY
CARF-1100B
(USER’S MANUAL)
UTEL CO.,LTD.
N6YUT-1100B
UTEL CO.,LTD
CARF-1100B
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS :
(1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
Caution : Any changes or modifications in
construction of this device which are not
expressly approved by the party responsible
for compliance could void the users
authority to operate the equipment.
Please check the followings before use.
1. This manual explained mainly the CARF-1100 model functions.
2. Once the engine( for manual transmission ) is started
(by the key or remote controller), the engine does not stop
even if the key is pulled out from the key box.
After the user gets off the car, the doors will be
locked and the engine will stop. (confirmation is required)
3. When the program is completed, the program jumper
(cable of 2 PIN connector) must be cut. If the wire is still connected,
the remote controller does not work.
4. After reading this manual, please confirm function of this
product (whether they correspond with directions written on this
manual) If any problem is founded, please contact our agency
or company
We do not have any reasonabilities for wrong operation
coming from SET UP/SET UP program errors.
CAUTION : This product must be installed by a technician who
is instructed by UTEL(or agency)and arbitrary
installation is prohibited.
For the efficient use:
1. Codeless communication devices can be interrupted by
near electronic waves and the territorial characteristics will
have an influence on the communication distance.
2. For the efficient management of the car equipped with this
product, please check the communication distance and if it is
necessary the user can extend the distance by using the antenna.
1
THE TABLE OF CONTENTS
1. Components
2. Function of CARF-1100
1) CARF - 1100
2) Function of the buttons
3. Usage of CARF-1100
1) Function of button I
(1)Arm /Disarm (Door lock/Unlock)
(2)Valet ON/OFF
2) Function of button II
(1)Auto transmission car
(2)Manual transmission car
3) Function of button III
(1)Opening the trunk
(2)Knock, shock sensor ON/OFF
4) Function of button IV
(1) Confirmation of the car condition
(2) Panic function(emergency alarm)
5) Knock sensor
6) Auto re-arm
7) Enable/disable chirp
8) Operation of A/C/Heater
9) Cancellation of the alert tone
10) Low battery alarm
11) Change of arm delay time
4. Installation
1) Check list of carf series.
2) Connection and color code of the main harness ass'y
3) How to find wires(color and functions)
4) Wiring diagram
5) Program method
5. Warranty sheet
2
1. Components
REMOTE(CARF-1100R) BASE MODULE(CARF-1100B)
MAIN SIREN
SHOCK SENSOR CABLE (4,6,8,10 pin connector)
3
2.Function of CARF-1100
1) CARF-1100
REMOTE CONTROLLED ENGINE START
EMERGENCY LIGHTING
AIR CONDITIONER AND HEATER OPERATION
DOOR LOCK/UNLOCK
VALET FUNCTION
AUTO RE-ARM
PANIC FUNCTION(EMERGENCY ALARM)
CONFIRMATION OF THE ALARM
TRUNK OPEN
KNOCK SENSOR
SHOCK SENSOR(IMPACT SENSOR)
DOOR OPEN ALARM
CONFIRMATION OF THE CAR CONDITION
CONFIRMATION OF THE COMMUNICATION DISTANCE
ENABLE AND DISABLE CHIRP
2) FUNCTION OF THE BUTTONS
Short : press the button A beep accompanied by a green blink will occur once
(remote controller)
long : press the button for more than 2 seconds.
The beep accompanied by a green blink will occur twice.
4
5
3. Usage of CARF-1100
Button Button
press
Door
(CONDITION)
Function CONFIRMATION SOUND
(REMOTE CONTROLLER)
SHORT CLOSED DOOR LOCK
DOOR UNLOCK
1 BEEP, 1 GREEN LED
2.BEEPS, 2.GREEN LEDS
LONG CLOSED VALET ON
VALET OFF
1 DUAL-BEEP, 1 GREEN LED
1 BEEP-HIGH-LOW, 1.GREEN LED
SHORT CLOSED
(LOCKED)
REMOTE
ENGINE START
ENGINE STOP
1 CRIKET SOUND
1 GREEN LED
2 CRIKET SOUNDS
2GREEN LEDS
CLOSED ARM DELAY
TIME 4,10 SEC
ARM DELAY TIME AFTER 2SEC
4SEC
→
10SEC, 10SEC
→
4SEC
LONG
OPENED CHIRP ON/OFF SOUND ON/OFF AFTER 2 SEC
SHORT CLOSED
OPENED
TRUNK OPEN 2 DUAL-BEEPS
2GREEN LEDS
LONG CLOSED
(UNLOCKED)
KNOCK, IMPACT
SENSOR
1 BEEP
1GREEN LED
SHORT CLOSED
OPENED
CHECKING
CAR CONDITION
DEPENDS ON
FUNCTION
LONG CLOSED
OPENED
PANIC ON 1 BEEP
1 GREEN LED AFTER 2 SEC
Confirmation sound will be heard from the remote controller after each button
is pressed( A beep with a green LED blink ) When it occurs, please remove
your finger from the buttons.
(If you keep pressing the button, This set may operate another function)
Example) To lock the door, press "button"of the remote controller.
When the button is pressed. The beep accompanied by a green blink will occur
once on the remote controller, then the same thing will happen to the car (The
turn signal with a chirp will blink once.) This means the door is locked,
After a little while the car will send the call back signal to the remote
controller.(The beep with green LED blink)
CALLBACK ?
- When the button of the remote controller is pressed and the
command is performed, this signal will be sent to the remote controller
from the car to confirm that the command has been recognized.
6
1)Function of the button
(1) Arm/Disarm(Door lock/Unlock)
1. When the "button " is pressed, the beep will sound and the green LED will
blink
once each on the remote controller.
2.The chirp accompanied by the turn signal blink will occur at the same time
on the car, then the doors will be locked and the callback signal will be sent
from the car.
3.When the "button" is pressed once again, another beep and green LED blink
will occur on the remote controller, but with the car, the chirp accompanied
by the turn signal blink will occur twice),then the doors will be
unlocked.(Callback signal will be sent once again-two beeps with two LED
blink)
4. If you try to open the locked door with the key(not with the remote
controller)or just by the force, the alarm will start and both the sound
and yellow LED blink will arise 8 times on the remote controller.
Right at this moment, if you press the "button ",the alarm will stop and
if the "button"is pressed again, then the car will be in the "disarm
mode".
The button has the alarm function and the function of
the auto engine-start reservation.
The engine (for the manual transmission car)does not go off even if the key
is pulled out from the key box. If you press the "button"after you get
off the car, doors will be locked and the engine will stop. And then, the
car will be in the "arm mode" and "remote starting reservation mode".
If the functions do not match with the above please contact the agency or
our company because problems might happen to the system owing to the
misinstallation.
(2) Valet on / off
Valet on/off
It is the function to suspend this system from operation. If the "valet"
is on, most of functions will be suspended except the "door lock/unlock".
If it turns "valet off", every function of the system will operate again.
1 If the "button"is pressed for more than 2 seconds when all doors are
closed(A beep accompanied by a green LED blink will occur twice on the
remote controller) then you will hear a chirp from the car and the turn
signal lamp will blink 3 times. This shows the "valet" is on and the
callback signal will be sent.
When the valet system is on, most of function will
be suspended except the door lock/unlock.
7
If the same procedure as procedure is done, the “valet mode” will be
off and the callback signal will be sent too.
Every function will operate again.
If you open the door by the key(in case you lose the remote controller or
the battery is all used up), the alarm will sound for 30 sec. Just start
the engine by the key to turn off the alarm.
To stop the engine, you get off the car( for the manual transmission),
close the door and press the "button".
The engine will stop and the doors will be locked and the car will enter
the "arm mode" with the "remote engine starting reservation".
If the engine does not stop even if you followed the procedure (because
of the mechanical problem) then press the "button" for long to let the
"VALET" function turn on. This will stop the engine and lock the doors.( If
the engine does not stop continuously, this status indicates the door pin
has a problem, so fix it at the near auto-repair shop.)
The VALET function is useful when you lend your
car to another or when you repair the car or
when you park your car at a parking lot where
other person keeps your key.
8
2) Function of button
(1) Auto transmission car
When the auto transmission car is in the [p] or [n] position and doors are
locked, the car will be in the remote controller engine starting reservation
and the arm mode.
Remote-controll engine start.
If you press button shrotly, then a beep sound and a turn signal lamp
blink will be made on the car. Callback signal will be sent and the engine
will start after 5 sec.(diesel car takes 10 sec.)
After the engine is started, the car will have 3 chirp sounds and 3 turn
signal lamp blinks. The same thing will occur on the remote controller by
the callback signal.(After the callback, the turn signal lamp will blink
every 7 sec.)
Engine stopping
The condition of engine is started, press button to stop the engine.(A
sound and a blink will be made for both the car and the remote controller.
The bugger wil beep sound and the green LED will blink 2 times on the remote
controller by the callback signal.)
(2) Manual transmission car
Every functions is same as those of auto transmission car except starting the
engine with the remote controller.
The manual transmission car has to have auto-engine starting reservation
process as follows.
Start reservation
As it is explained before, the engine does not goes off even if you pull
out the ignition key while the engine is running. To have starting
reservation, first pull out the ignition key, get off the car and close
the door, and then press buttonto lock the door and turn off the
engine.
The arm with starting reservation will be set. and callback signal will
be made.(this process has to be done with in 20 sec.)
Cancel reservation .
By pressing the button( after pull out the key and get off the car) the
engine will stop and the engine start reservation will be cancelled with
disarm mode.
If you press the buttonagain, the car will be in arm mode without
starting reservation.
9
You can cancel the reservation when the door is locked and unlocked
during remote engine starting.
When the engine is stoped, the start reservation will be cancelled if
you open the door and closed.
Please observe the reservation proedure using key to restore reservation.
10
3) Function of button
(1) Trunk open
When the button is pressed until a beep sound and green LED blink comes out
then the trunk will open and, the callback signal will be followed.
(2) knock sensor & Shock sensor on/off
1 If the button is pressed for more than 2 seconds in condition that car
is in arm mode, then the knock sensor and shock sensor will be off.
A beep sound with a green LED blink will occur on the remote controller
after a while. The above occurs once again.
The turn signal lamp will blink 3 times and callback signal will be
followed.
If is repeated, the knock, and shock sensor will be on.
11
4) Function of button
(1) Confirmation of the car condition.
1 If button is pressed, the user will receive a call back signal to be
informed and the car condition.( A beep sound with a green LED blink will
be made on the remote controller. A chirp sound with a turn signal lamp
blink will be made on the car too.)
2 The callback signals, which The user can receive are the followings.(All
of the signals will be received by the remote controller.)
Arm : A beep sound with a green LED blink.
Disarm : Two beep sound with two green LED blinks.
Remote engine start : Three beep sound with three green LED blinks.
Remote engine stop : Two-sounds with two green LED blinks.
Trunk open : Two beep sound with two green LED blinks.
Low battery warning : two beep sound with two red LED blinks.
Valet on/off : Lock (A beep sound ), unlock(two beep sounds).
Error sign indicate : When any button is pressed, the remote waits
callback. If there is no callback, remote sends an error signal.
Error signal is 3 beep sounds with 3 red LED blinks (The regular callback
signal makes green LED blink but low battery warning and error signal make
red LED blink)
Communication distance : If button is pressed, the car condition will
be informed by the callback signal.
If the car is out of the communication distance error sign will be
made(Three beep sounds with three red LED blinks.)
(2) Panic function
If the button is pressed for more than 2 seconds, a beep sound with a green
LED blink will occur on the remote controller. After a while another beep
sound and green LED blink will occur. The car will make a alarm for 30 sec
with the turn signal lamp blinks. And the callback signal will be followed.
Press the buttonto stop the alarm.
5) Knock sensor
If the sticker attached on the left conner of the front glass of the car is
knocked lightly, then eight beep sounds with eight yellow LED blinks will be
made by
callback signal. Then the driver will know that he/she is paged. To stop the
callback signal on the remote, press any button shortly.
12
6) Auto re-arm
1 If the door is unlocked by mis-contact of a button after the door was
locked a
beep sound with a turn signal lamp blink will be made and then re-arm will
work to
lock the door after 10 seconds of mis-contact.
If you open the door and closed above situation,re-arm will be cancelled.
7) Enable/ Disable chirp
1 Disable chirp : Let a door opened, then press the button for a long time.(
a beep
sound with a green LED blink will be made. After a while another beep sound
and green
LED blink will be made.)
This action will disable all the chirps from the car except 30 sec alarm.
Enable chirp : By repeating action chirp sound will be enabled.
8) Operation of A/C/Heater
To operate the A/C or the Heater beforehand, turn the switch on before getting
off the car, then the A/C or the heater will work after two minutes since the
engine has been started by the remote controller. This is only for the car
with mechanical switch.
9) Cancel alert tone
1 Alarm will sound and the turn signal lamp will blink for 30 sec, in arm mode
if you try to open the car with the key. Eight beep sounds with orange LED
blinks are made on the remote controller by the callback signal.
(If the door is not closed, the above process will be repeated.)
2 If you press any button after closing the door, the alarm will stop. If the
button I is pressed again, the alarm will be removed.
3 Alert tone can be cancelled by starting the engine with the ignition key
when you cannot use the remote controller.
10) Low battery alarm
If the battery is low and the button is pressed, the remote controller will
have the low battery warning alarm after performing the task(two beep sounds
with two red light blinks.) Please change the battery right after the warning
alarm is heard.
Example) If you pressed button I in the state of low battery to open the door,
then a beep sound with a green LED blink on remote controller and two beep
sound with two turn signal lamp light blinks will be made on the when the
doors will be unlocked.
After a while a call back signal(Two beep sounds and two green light blinks)
will be appeared on the remote and low battery warning alarm will be followed.
13
11) Change of arm delay time
There is some delay time called arm delay time until the arm mode is set up
after
the buttonis pressed.
The LED on the receiver ass’y is lighted continuously during arm delay time.
1 The arm delay has been adjusted to 10 seconds when it was shipped from the
factory. 10 second arm delay is used for the cars of which the room lamp
goes out slowly when the door has been opened and closed.
2 Press the button for more than 2 seconds when the car is in a disarm mode
and the door is closed.
And then, the arm delay time will be adjusted from 10 seconds to 4 seconds,
vice versa.
3 If the system has been adjusted to 10 seconds of arm delay time the car
enters the arm mode even if the room lamp lights up. But the siren built in
the car will sounds and the turn signal lamp will blink after 10 seconds if
the door has been opened.
14
4. Installation
1) Check list of CARF series
Before installing the CARF series system in a car, first check the following
points.
(1) Check the following conditions of the car
1.Engine ignition
2.Operation of heater & A/C
3.Operation of turn signal lamp
4.Operation of room lamp
5.Operation of door motor(Lock/Unlock of door)
6.The other electrical conditions
(2) Check the following conditions of the harness assy's connected
in
the car
1.Connectors
2.Position of each wire
(3) Select suitable mounting positions for the main box and the
siren
included in the CARF series system
(4) Make sure that the car is equipped with the door motor.
1) Connection and color code of main harness ass'y
To check the power supply of the following points, you can use the test probe
which contains a lamp.
(1) Power supply(B+:Red)
Function : Power supply from the battery-When the battery is checked by the
test probe, The probe lamp should be lighted steadily.
(2) Ignition1-IG1(Green)
Function : Power supply except start motor, heater, A/C and car stereo-The
probe lamp should be lighted when the ignition key is in the “ON” position and
the engine is started.
(3) Ignition2-IG2(White)
Function : Power supply of heater and A/C-The probe lamp should be lighted
when the key is in the“ON”position and the probe lamp off when the engine is
starting time.
(4) Start (Yellow)
Function : Power supply of start motor(alternator)- The probe lamp should
be lighted when the engine is started.
15
(5) ACC (Only applicable to some cars)
The probe lamp should be lighted when the ignition key is in the“ACC”position.
3) How to find wires(color and functions)
NOTE : Following functions can be checked by connecting probe lamp with exact
wires.
(1) Door S/W (Orange):Negative trigger method
When door is opened, the room lamp comes on and DOOR-OPEN-INDICATOR on the
gauge board located in front of car will be displayed.
Test lamp turns on when the room lamp is off and when room lamp is on test
lamp is off.
(2) Door lock(Gray), Door unlock(Yellow)
(Cars equipped with the door motor)Door lock(Red stripe on gray) /Door
unlock(Red
stripe on yellow) Cars of which the door motor has to be installed.
The CARF series have two kinds of wires for door lock/unlock function.
A door is locked and unlocked automatically by using the remote controller.
Test lamp turns on and off if door is locked and unlocked when the first key
of the remote controller is used.
(3) Trunk open (White stripe on red)
The trunk can be opened by using the remote controller.
The lamp is turned on when the trunk switch is pressed.
(4) Light 1 & Light 2 (Black stripe on white)
Turn signal lamp blinks when the set is operating.
Test lamp blinks when the lever of turn signal lamp is located to upward or
downward point.
This set has two wires for light(light1 & light2),which are operating
independently.
Two wires can be checked when the lever of the turn signal lamp is upward or
downward.
(5) L Terminal of alternator(Green)
This function informs whether the engine is started or not.
You can see several conditions depending on the types of cars.
1. Test lamp grows dim when the ignition key in the “ON”position and it turns
on brightly when the engine is started.
2.Test lamp is off when the ignition key is in “ON” position and, it lights
brightly when the engine is started.
3.When the ignition key is in ”ON” position, the probe lamp lights and comes
off after a while. And then, test lamp turns on again when the engine is
started.
16
4) Wiring diagram
INSTALLATION OF CARF-1000
1) WIRING DIAGRAM OF DEVICE SETTING (MAIN 6 PIN CONNECTOR)
RED : + 12 VEMPTY TERMINAL
BLACK : -EARTH(GROUND) YELLOW : START
GREEN : IG 1 WHITE : IG 2
(2) 10 PIN CONNECTOR(FUNCTION WIRES)
BLUE : DOOR PIN(+)
ORANGE : DOOR PIN(-)
GREEN : GENERATOR
WHITE/BLACK : FLICKER 1
BROWN : SIREN
RED/WHITE: TRUNK
VIOLET : TRUNK IN
GRAY : LOCK(WIRE FOR THE CARS THAT HAVE TO BE EQUIPPED WITH THE DOOR MOTOR)
YELLOW : UNLOCK
WHITE/BLACK : TURN SIGNAL LAMP
(3) 8 PIN
BASE COMMUNICATION MODULE BE CONNECTED TO CONNECTOR
(4) 4 PIN CONNECTOR ( CAR WITH THE DOOR MOTOR )
GRAY/RED : LOCK (LOCK CABLE OF CAR WITH THE DOOR MOTOR)
EMPTY TERMINAL EMPTY TERMINAL
YELLOW/RED : UNLOCK(UNLOCK CABLE OF CAR WITH THE DOOR MOTOR)
(5) 3 PIN CONNECTOR
SHOCK SENSOR
17
(6) 2 PIN CONNECTOR
PROGRAM LINE, AFTER THE INSTALLATION,PLEASE CUT OFF OR PULL OUT.
10 9 8 7 6
54321
41
52
63
8765
4321
43 2 132 121
5) Program method
(1) program preparing work
Connect all the connectors except the main connector.
Of the above diagram, check if the black wire of 2 pin connector
( which is the program jumper ) is connected.
If is not connected( used cars, a/s cars), connector it to 2 pin
connector.
After excuting the above steps connect 6 pin connector.
And then, the LED on the base communication module will be lighted.
This indicates the program is ready.
(2) Program method 1 (If one remote controller is used)
1 First program : Choose a button from the below selections to decide
the starting time.
press the button until a beep sound is heard. A beep sound with A turn
signal lamp blink will occur from the car. After a while, the remote
controller will have three beep sound with three green LED blinks.
1st starting 2st starting 3st starting
Button : 0.7 sec 1.1 sec 1.5 sec
Button : 1.1 sec 1.1 sec 1.1 sec
Button : 1.5 sec 1.5 sec 1.5 sec
2 Second program : Choose a button from the below selections. to decide
the type of oil press the button until a beep sound is heard. two beep
sound with two the turn sign lamp blinks. will have three beep sound
with three red LED blinks.
Button : Applicable for the gasoline engine cars.
Button : Applicable for the diesel engine cars.
3 Third program : Chose a button from the below selections. Follow the
steps just like the first and the second programs. Programming is
completed after beeps and blinks.
Button : Manual transmission car.
Button : Auto transmission car.
18
(3) Program Method 2 (If two remote controllers are used.)
1 First program : Perform exactly the same procedure as the program method
1( first program ) with the remote controller 1.
2 Second program : perform exactly the same procedure as the program method
2( second program) with the remote controller 2.
3 Third program : Chose one remote controller and follow the same procedure
as
the program method ( third program )
After the third program is made, all of the programming process will
be completed.
If all of the programs are done, please cut out the black wire of the
2 pin connector.(the car will have three beep sounds with three
directional light blinks and the receiver lamp will be turned off.)
After excuting the above steps check if all the functions are
working correctly, then all the works are done.
19
WARRANTY
This product has passed through the thorough quality control and the close
examination.
If there is any manufactural defect or spontaneous trouble, call our company
or agent. We will repair it without extra charges.
GUARANTEE INFORMATION
1. Guarantee period is 12 months from the day of purchasing.
2. But, we receive fee for the repairing in the following cases.
In case that the guarantee-period of free charge is over
In case that the product is out of order because of careless using
In case that it is a hindrance by natural calamity
In case that it is a hindrance by inadequate repair, or change of inner-
structure
3. The standard of reward in repairing the product, exchange and refund follow
the
consumer-damage-reward-act composed by the Economic Planning Board.
4. The retention period of component parts are 5 years after the cease of
product.
Note : Please make sure that all of above form has been filled out.
20
SPECIFICATIONS
1. GENERAL
- ANTENNA : DIPOLE ANTENNA
- FREQUENCY RANGE : 447.6375MHz
DATE
NAME TELCUSTOMER
ADDRESS
NAME TELSHOP
ADDRESS
SERVICE DATE
- MODULATION MODE : F2D
- COMMUNICATION MODE : 1CH HALF DUPLEX
- POWER SUPPLY : DC +5V
- CHANNEL SPACE : 12.5KHz
- OPERATING TEMPERATURE : -20 ~ +60
- DEMENSIONS : 57.4 ( H ) * 38.7 ( W ) * 15 ( D )
2. ELECTRICAL
1) Transmitter
- OUTPUT IMPEDANCE : 50Ω
- MODULATION METHOD : CRYSTAL MODULATION
- FREQUENCY STABILITY : ±0.0005%
2) Receiver
- RECEIVING METHOD : SUPER HETERODYNE
- IF FREQUENCY : 10.7MHz, 455KHz
- FREAUENCY STABILITY : ±0.0005%
- OUTPUT IMPEDANCE : 50Ω