VERO GLOBAL COMMUNICATION VR-P25V Radio Amplifier User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3796006
Application ID	VeXydst4kaRIdQj6wEr1Pg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.15kB (114384 bits)
Date Submitted	2018-03-26 00:00:00
Date Available	2018-03-26 00:00:00
Creation Date	2018-03-13 11:08:36
Producing Software	Foxit Reader PDF Printer Version 7.1.0.112
Document Lastmod	2018-03-13 11:08:36
Document Title	User manual

VERO AMPLIFIER USER MANUAL
【READ FIRST 】：
 The VERO Series Amplifiers are available in different frequency bands and
frequency modulation modes (D Series covers both FDMA/TDMA).



Transmitting Out of Band (Example: Transmitting VHF on UHF):
 FDMA Amplifier: Transmitting out of band on the FDMA Amplifiers will
pass through the direct HT power through. Ensure the connected antenna
is matched and you can transmit out of band without amplification
 TDMA Amplifier (D Series): Amplifier will not transmit out of band
(example: it will not transmit a VHF signal on the UHF amplifier (vice
versa)). Do not transmit out of band on the TDMA (D Series) Amplifier
Transmitting on a different Modulation Mode:
 FDMA Amplifier: The FDMA amplifier will not properly transmit another
other modulation mode (such as DMR which is TDMA)
 TDMA Amplifier (D Series): The TDMA Amplifier is compatible with both
FDMA and TDMA signals. It will automatically transmit the proper signal
Use a Proper External Antenna to the Amplifier
Antenna Basics
Your VERO Amplifier does not include an Antenna. It is very Important to not transmit
without an antenna or dummy load attached to the amplifier. Doing so, may cause
harm to the radio equipment.
You will want to choose a suitable antenna for the bands you plan on transmitting and
receiving on.
Example: If you plan on transmitting on 145MHz you will want to ensure you have
picked an antenna that states it is capable of working with 145MHz.
If an antenna is not properly tuned for the frequency you transmit on – it can cause
damage with the reflected power going back into the radio. Pick an antenna with SWR
of less than 1.5:1 to safely transmit.
Magnetically Mounted Antennas:
These antennas must be grounded to a metal surface, such as a vehicle body.
Magnetic base antennas do not properly operate unless they are fully magnetically
grounded first.
【Product Highlights 】:
●The VERO Amplifier series are portable, lightweight, wide coverage RF power amplifiers for
Handheld Radio equipment.
●Dual mode Amplifier for both Digital and Analog Radio Automatic recognition of digital and analog
systems.
Use the FDMA Amplifier for: Analog, P25 Phase 1, C4FM (System Fusion), NXDN, IDAS,
dPMR, MPT1327
Use the D Series TDMA Amplifier for all FDMA Modes Plus DMR and P25 Phase 2
TDMA Amplifier Signified by “D” on Model Number
●High output power up from 20-30 watts (Input: 2-6 watts)
●Small size: This amplifier's size makes it the perfect companion for field operation without the
added weight.
●Includes Voltage Spike Suppression, Over Temperature Protection, RF sensing, Automatic Power
Control (APC), Harmonic Filters.
●Harmonic Filters: Purifies the input signal and transmits a cleaner signal
●Built-in large speaker and microphone socket.
●Status indicators: Shows on the amplifier the current status.
【Three Basic Options to Operate your Amplifier 】：
Option 1:Only connect to the Antenna Jacks on the Radio and Amplifier – Use the radio itself to
operate the amplifier
Option 2： Only connect to the Antenna Jacks on the Radio and Amplifier – Use the accessory jack
on the radio to an external mic or earpiece to operate the amplifier
Option 3:Connect both to the Antenna Jacks and Audio jacks on the Radio and Amplifier – Use the
supplied microphone and built in speaker to operate the amplifier without using the radio itself.
FCC Statement
This equipment has been tested and found to comply with the limits for part 90 of FCC
Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates and can radiate
radio frequency energy. If not installed and used in accordance with the instructions, it
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. Verification of
harmful interference by this equipment to radio or television reception can be
determined by turning it off and then on. The user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna. Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a different circuit to that of the receiver's
outlet.
Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation.
Note: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Compliance with RF Exposure Standards
United States Federal Communications Commission, Code of Federal Regulations; 47
CFR §1.1307, 1.1310 and 2.1091
American National Standards Institute (ANSI) / Institute of Electrical and Electronic
Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015.
Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
RF Exposure Compliance and Control Guidelines and Operating Instructions
To control your exposure and ensure compliance with the occupational/controlled
environment exposure limits always adhere to the following procedures.
Guidelines:
Do not remove the RF Exposure Label from the device.
User awareness instructions should accompany device when transferred to other users.
Do not use this device if the operational requirements described herein are not met.
Operating Instructions:
Keep the device at least 50 mm away from the body. Keeping the device at the proper
distance is important as RF exposure decreases with distance from the antenna. The
antenna should be kept away from the face and eyes.
Use of non-approved accessories may result in exposure levels which exceed the FCC's
occupational/controlled environmental RF exposure limits.
Use of non-approved antennas, batteries, and accessories cause the repeater to
exceed the FCC RF exposure guidelines.
Contact your local dealer for the product's optional accessories.
【Supplied Accessories】
Body 1pc
Mobile Mounting Bracket & Screw set 1pc
Radio to Amplifier RF cable 1pc
User Manual 1pc
【Specifications】：
●Frequency range：
136MHz-174MHz VR-P25&VR-P25D&VR-P35&VR-P55
●Power supply：DC 13.8V （±15%）
●Input RF power：2 - 6W （±10%）
●Output RF power：20 - 30W
●Current：4.0-5.5A
●Size：135*115*35mm
●Net weight：800g

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 5
Author                          : 
Create Date                     : 2018:03:13 11:08:36+08:00
Creator                         : 
Modify Date                     : 2018:03:13 11:08:36+08:00
Producer                        : Foxit Reader PDF Printer Version 7.1.0.112
Subject                         : 
Title                           : 

EXIF Metadata provided by EXIF.tools