VIA Technologies VAB820-WA1 11n+BT WiFi Board User Manual

VIA Technologies, Inc. 11n+BT WiFi Board

User Manual

Download: VIA Technologies VAB820-WA1 11n+BT WiFi Board User Manual
Mirror Download [FCC.gov]VIA Technologies VAB820-WA1 11n+BT WiFi Board User Manual
Document ID3227866
Application IDUgIv6DbLyG8zAd+7CGmLuQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize133.36kB (1666958 bits)
Date Submitted2016-12-14 00:00:00
Date Available2016-12-14 00:00:00
Creation Date2016-12-09 17:36:06
Producing SoftwareAdobe Acrobat 10.0 Image Conversion Plug-in
Document Lastmod2016-12-13 09:31:20
Document TitleUser Manual
Document CreatorAdobe Acrobat 10.0

XIX
we connect
User Manual
VAB-SZO-W
11n+BT WiFi board
Introduction:
VABeSZOeW is a WLAN lln and Bluetooth board, which fully supports the features and
functional compliance of IEEE 802.11b/g/n standards, Bluetooth v2.1, v3.0 and v4.0
standards. It supports up to 150Mbps WLAN network
It is designed to provide excellent performance with low power consumption and
enhance the advantages of robust system and cost-effective.
Specification
WiFi/ Bluetooth
- CM-87ZEBV 11n+BT WiFi module (USB interface)
Onboard I/O
- 1 x USB pin header for WiFi/BT module
Operation temperature
- o~ 60"(3
Humidity
- 0% "' 95% (non-condensing)
Federal Cnmmunieation Cnmmission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits fora Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. lfthis equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment offand on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna Of transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator St your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their endrproduct for any additional
compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or corlocation with another transmitter), then the FCC authorization is
no longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following: "Contains FCC ID:
NCI-VABSZD-WAl", The grantee's FCC ID can be used only when all FCC compliance
requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
This end user manual shall include all required regulatory information/warning as
show in this manual.
Host integration insiructions
1 Pm Description
Onboard USB connector
Th: vAaaQAWmm has an anboad use :m
Hadzd is my N plnout D‘mrconnzdnr 5 shown
below
use N5_nr
use «syn
«c
nm.um_g
2 Instauatlons
Installing EMIGSSKIVOOAI WLAN Krt
Sup)
mm“ m vAB-azaw mdun: md seem n mm m screws
' 9
sup:
(mm m: use trimmm am: an m: anbold use
emnar (USBM Then (unto me and m mm (ab-1m
me Just! 'pm mmdmmgdu on me mm“
(mumrzmrmu
5w 3
mm m: pm 01 stamina my: mm m: mam nnv’e mm n:
me: um and menu: “mum nwm me nma'w:
msanmc-polam
5w ¢
Gem, camera 0.: mm m a; new; cable m m: mlm R;
mama on vmme w mum

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2016:12:13 09:31:20+08:00
Create Date                     : 2016:12:09 17:36:06+08:00
Metadata Date                   : 2016:12:13 09:31:20+08:00
Creator Tool                    : Adobe Acrobat 10.0
Format                          : application/pdf
Document ID                     : uuid:a5201c3b-ace3-42fa-8d30-0324e657b650
Instance ID                     : uuid:4bbf07a1-d554-4a75-a87c-c939b9bc6854
Producer                        : Adobe Acrobat 10.0 Image Conversion Plug-in
Page Count                      : 6
Creator                         : Adobe Acrobat 10.0
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NCI-VAB820-WA1

Navigation menu