VIEWMAX VM032 LCD Monitor with PC User Manual

VIEWMAX Corporation LCD Monitor with PC

User Manual

Page 1 ATTRACT, DISPLAY, INFORMPROFESSIONAL LCD DISPLAY SIGNAGEOPERATION MANUALVM042H/VM032
Page 2 WARNING OWNER’S RECORD The model and serial numbers are located on the rear of the unit. Record the model and serial numbers in the spaces provided below for record purposes. Refer to these numbers whenever you call your local dealer regarding this product. Model Number: Serial Number: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. On Transportation Hold the unit itself and not the speakers (if applicable) when you carry the display unit. Failing to do so may result in dropping the unit and causing serious damage and/or injury. For customers in the U.S.A. If you have any questions about this product, you may call Viewmax Corporation’s Customer Service Center 1-800-000-0000 or http://www.ati-eng.com. Declaration of Conformity Trade Name: Viewmax Corporation Ltd. Model: VM042(H) Responsible Party: Viewmax Corporation Ltd. Address: 1214, Sicox Tower, 513-14, Sangdaewon-Dong, Jungwon-Gu, Seongnam, Gyeonggi-Do, Korea Telephone Number: +82-31-745-7812 Email Address: info@viewmaxcorp.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer on an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
Page 3 TABLE OF CONTENTS PPRREECCAAUUTTIIOONNSS..............................................................................................................................................................................................................77 General Safety Guide...........................................................................................................................7 Installation................................................................................................................................................. 7 Cleaning.................................................................................................................................................... 7 Notes on Handling and Cleaning the Display Panel................................................................................. 7 Repacking................................................................................................................................................. 7 LLOOCCAATTIIOONNSS AANNDD FFUUNNCCTTIIOONN OOFF CCOONNTTRROOLLSS............................................................................................................................88 Front / Rear / Side / Bottom Views......................................................................................................8 X Indicator and OSD Control Buttons ...................................................................................................... 8 Y Computer Access Panel....................................................................................................................... 8 Z Wall Mount Installation Holes ............................................................................................................... 8 [ Connector Panel Cover ........................................................................................................................ 8 Control Button Section (Side).............................................................................................................9 X Power Button.................................................................................................................................... 9 Y Menu Button ......................................................................................................................................... 9 Z Select Button ........................................................................................................................................ 9 [ \ ©/ª Up/Down Buttons..................................................................................................................... 9 ] Power and Standby Indicator Light ...................................................................................................... 9 ^ Rubber Plug.......................................................................................................................................... 9 Remote Control (Optional) ................................................................................................................10 iMON Pad Controller............................................................................................................................... 10 Using iMEDIAN....................................................................................................................................... 12 Connector Panel.................................................................................................................................13 X Mouse PS/2 Connector ...................................................................................................................... 13 Y Keyboard PS/2 Connector.................................................................................................................. 13 Z DVI Port .............................................................................................................................................. 13 [ USB Ports........................................................................................................................................... 13 \ Audio Connection Port........................................................................................................................ 13 ] LAN Port ............................................................................................................................................. 13 ^ VGA Port ............................................................................................................................................ 14 IINNSSTTAALLLLAATTIIOONN//MMOOUUNNTTIINNGG GGUUIIDDEE....................................................................................................................................................1155 Before you start..................................................................................................................................15 Installation Precautions........................................................................................................................... 15 Preinstalled Components........................................................................................................................ 15 Installation and Configuration Steps................................................................................................15 Unpacking............................................................................................................................................... 15 Packing List ............................................................................................................................................ 16 Mounting Space Requirements.........................................................................................................16 Mounting the Display Horizontally .......................................................................................................... 17 Mounting the Display Vertically .............................................................................................................. 17 Using the Optional Stand (not supplied)................................................................................................. 17 Mounting the System.........................................................................................................................18 Wall Mounting ......................................................................................................................................... 18 Using the Monitor Stand (Optional) ........................................................................................................ 21 Connecting the AC Power Cord........................................................................................................22 Connecting the Speakers (Optional) ................................................................................................22 UUSSIINNGG OONN--SSCCRREEEENN--DDIISSPPLLAAYY ((OOSSDD)) MMEENNUUSS..................................................................................................................2233 Operating OSD Menus .......................................................................................................................23 Menu operating buttons .......................................................................................................................... 23 Configuration of the Menu ...................................................................................................................... 23
Page 4 Menu Guide.........................................................................................................................................24 Color Mode..........................................................................................................................................24 Contrast .................................................................................................................................................. 24 Brightness............................................................................................................................................... 24 Color Adjust ............................................................................................................................................ 24 Color Temperature.................................................................................................................................. 24 Image Setting......................................................................................................................................25 Clock ....................................................................................................................................................... 25 Phase...................................................................................................................................................... 25 Gamma ................................................................................................................................................... 25 Sharpness............................................................................................................................................... 25 Position ...............................................................................................................................................26 H. Position............................................................................................................................................... 26 V. Position............................................................................................................................................... 26 Fit to Screen ........................................................................................................................................... 26 OSD Menu ...........................................................................................................................................26 OSD H. Position...................................................................................................................................... 26 OSD V. Position...................................................................................................................................... 26 OSD Timer.............................................................................................................................................. 27 Language ............................................................................................................................................27 Miscellaneous.....................................................................................................................................27 Signal Source ......................................................................................................................................... 28 Volume.................................................................................................................................................... 28 Mute ........................................................................................................................................................ 28 Reset....................................................................................................................................................... 28 SSPPEECCIIFFIICCAATTIIOONNSS....................................................................................................................................................................................................2299 System Specifications .......................................................................................................................29 Mainboard Specifications..................................................................................................................29 Flat Panel Screen Specifications......................................................................................................29 MMAAIINNBBOOAARRDD................................................................................................................................................................................................................3300 Introduction ........................................................................................................................................30 CPU......................................................................................................................................................30 On-Board Chipset...............................................................................................................................30 Peripheral Device Interfaces, Connectors and Slots......................................................................31 Internal Slots........................................................................................................................................... 31 Internal Peripheral Device Connectors................................................................................................... 32 External Peripheral Device Connectors.................................................................................................. 32 SSYYSSTTEEMM MMAAIINNTTEENNAANNCCEE..............................................................................................................................................................................3333 System Maintenance Introduction....................................................................................................33 Mainboard Replacement....................................................................................................................33 Mainboard Access Panel Removal...................................................................................................33 Mainboard Access Panel Removal......................................................................................................... 34 Rear Panel Removal............................................................................................................................... 35 Component Replacements................................................................................................................36 Hark Disk Drive Replacement................................................................................................................. 36 Memory Module Replacement................................................................................................................ 36 DVD Drive Replacement......................................................................................................................... 37 BBIIOOSS SSEETTUUPP............................................................................................................................................................................................................3399 Entering Setup....................................................................................................................................39 Control Keys ........................................................................................................................................... 39
Page 5 Getting Help............................................................................................................................................ 39 Main Menu .............................................................................................................................................. 39 Sub-Menu ............................................................................................................................................... 39 General Help <F1> ................................................................................................................................. 39 The Main Menu ...................................................................................................................................40 Standard CMOS Features..................................................................................................................41 Date (MM:DD:YY)................................................................................................................................... 41 Time (HH:MM:SS) .................................................................................................................................. 41 IDE Primary Master/Slave, SATA 1~4.................................................................................................... 41 Device / Vendor / Size ............................................................................................................................ 42 LBA/Large Mode..................................................................................................................................... 42 DMA Mode.............................................................................................................................................. 42 Hard Disk S.M.A.R.T. ............................................................................................................................. 42 Floppy A.................................................................................................................................................. 42 System Information................................................................................................................................. 42 Advanced BIOS Features ..................................................................................................................43 Boot Sector Protection............................................................................................................................ 43 Full Screen LOGO Display ..................................................................................................................... 43 Quick Booting ......................................................................................................................................... 43 Boot Up Num-Lock LED ......................................................................................................................... 43 IOAPIC Function..................................................................................................................................... 43 MPS Table Version................................................................................................................................. 43 CPU Feature........................................................................................................................................... 44 Chipset Feature ...................................................................................................................................... 44 Boot Sequence ....................................................................................................................................... 44 Trusted Computing ................................................................................................................................. 45 Integrated Peripherals .......................................................................................................................45 USB Controller........................................................................................................................................ 45 USB Device Legacy Support .................................................................................................................. 45 Onboard LAN Controller ......................................................................................................................... 46 LAN Option ROM.................................................................................................................................... 46 Audio Controller ...................................................................................................................................... 46 On-Chip ATA Devices............................................................................................................................. 46 I/O Devices ............................................................................................................................................. 46 Power Management Setup.................................................................................................................47 ACPI Function......................................................................................................................................... 47 ACPI Standby State................................................................................................................................ 47 Suspend Time Out (Minute).................................................................................................................... 47 Power Button Function ........................................................................................................................... 47 Restore On AC Power Loss.................................................................................................................... 47 Wakeup Event Setup .............................................................................................................................. 48 PNP/PCI Configurations ....................................................................................................................49 Primary Graphic’s Adapter...................................................................................................................... 49 PCI Latency Timer .................................................................................................................................. 49 PCI Slot 1/2 IRQ ..................................................................................................................................... 49 IRQ Resource Setup............................................................................................................................... 49 H/W Monitor ........................................................................................................................................50 Chassis Intrusion .................................................................................................................................... 50 CPU/SYS Smart Fan Target................................................................................................................... 50 PC Health Status .................................................................................................................................... 50 Frequency/Voltage Control ...............................................................................................................51 Current CPU/DRAM Frequency.............................................................................................................. 51 Intel® EIST .............................................................................................................................................. 51 Advanced DRAM Configuration.............................................................................................................. 51 Configuration of DRAM Timing by SPD.................................................................................................. 51 FSB/Memory Ratio ................................................................................................................................. 52 Adjusted DDR Memory Frequency......................................................................................................... 52 Auto Disable DIMM/PCI Frequency........................................................................................................ 52 Memory Voltage (V)................................................................................................................................ 52
Page 6 PCI Express Voltage............................................................................................................................... 53 Spread Spectrum.................................................................................................................................... 53 Load Fail-Safe/Optimized Defaults ...................................................................................................53 BIOS Setting Password .....................................................................................................................53 TTRROOUUBBLLEESSHHOOOOTTIINNGG..........................................................................................................................................................................................5555 SSOOFFTTWWAARREE DDRRIIVVEERRSS......................................................................................................................................................................................5566 Mainboard Drivers..............................................................................................................................56 Additional Drivers ..............................................................................................................................56 Optional Drivers .................................................................................................................................56
Page 7 PPrreeccaauuttiioonnss General Safety Guide A nameplate indicating operating voltage, power consumption, etc. is located on the rear of the unit. Should any solid object or liquid fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating the unit any further. Unplug the unit from the wall outlet if it is not to be used for several days or more. To disconnect the AC power cord, pull it out by grasping the plug. Never pull the cord by itself. When you install the units on the floor, be sure to use the optional stand (if applicable). Installation Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. Do not install the unit in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. When you install multiple equipment with the unit, the following problems such as malfunction of the remote control, noisy picture, and noisy sound may occur depending on the position of the unit and other equipment. Cleaning Be sure to unplug the power cord from the unit and/or electrical outlet before cleaning the display unit. Gently wipe off stains using a dry soft cloth. Wire off grimy stains using a cloth slightly moistened with a mild detergent, then wipe the area again using a dry soft cloth. Never use alcohol, benzene or thinner for cleaning purposes. They may damage the finish of the display unit or can remove the markings on it. Notes on Handling and Cleaning the Display Panel The special surface finish on the LCD display panel should be treated with care when cleaning or handling the unit. When cleaning it, use a soft cleaning cloth to avoid any scratches or damage to the panel. Repacking Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit, repack it in the manner the unit was initially packed. Contact your authorized local dealer if you have any questions on this unit. Warning on Power Connection Use the proper power cord for your local power supply. United States, Canada Continental Europe United Kingdom, Ireland, Australia, New Zealand Plug type CM0233 COX-07 / 636 Appropriate rating plug which complies with local regulations Female end CM0089 COX-02 / VM0301B VM0303B Cord type SVT H05VV-F CEE (13) 53rd (O.C) Minimum cord set rating 10A/125V 10A/250V 10A/250V Safety approval UL/CSA VDE VDE
Page 8 LLooccaattiioonnss aanndd FFuunnccttiioonn ooff CCoonnttrroollss Front / Rear / Side / Bottom Views X Indicator and OSD Control Buttons The power and standby indicator lights up in green when the display unit is powered on. The indicator lights up in red in the standby mode and in orange when the display enters the power saving mode while a signal is input from a computer. See the “OSD (On-Screen-Display) Control Button” section for more details on page 23. Y Computer Access Panel Access to the embedded computer is easily obtained through the easy access panel located in the rear of the display unit. The access panel can be easily removed by unscrewing six large screws by hand. Z Wall Mount Installation Holes Use the ten wall mount installation holes to install the wall mount bracket or optional stand (not supplied). [ Connector Panel Cover For details on the connector panel, see “Connector Panel” on page 13. NOTE Be sure to familiarize yourself with all the locations of various controls and connectors before installing the display unit. Front View Rear View Bottom View [ XY Z[ X x
Page 9 Control Button Section (Side) X Power Button Press to power on the display unit and the embedded computer. Press again to return to the standby mode. Y Menu Button Press to show menus. Press again to hide them. Z Select Button Press to set your choice. [ \ ©/ª Up/Down Buttons Press to move the cursor up or down ] Power and Standby Indicator Light The power and standby indicator lights up in green when the display unit is powered on. The indicator lights up in red in the standby mode and in orange when the display enters the power saving mode while a signal is input from a computer. ^ Rubber Plug Not used. NOTE To turn off the display and the embedded computer, use the remote control or execute the Windows™ shutdown process from the computer. NOTE To protect the LCD panel, a certain amount of time is required to turn the unit on. Wait about 10 seconds after one operation before executing the next operation. \XYZ[]^
Page 10 Remote Control (Optional) iMON Pad remote controller is designed to control the power of both the LCD display and the internal computer and it will also serve as the mouse pointer using the Pad Controller of the remote controller. Using iMON, iMON pad remote controller can control not only iMEDIAN, but also every Windows applications. The following is the normal usage of the buttons on the iMON Pad remote controller. Please see the section ‘Using remote controller on iMEDIAN’ for instructions on using iMON Pad remote controller on iMEDIAN. iMON Pad Controller Power Button: This button is used to turn both the LCD display and computer On and Off. Application Exit Button: This button generates the keyboard short command, [ALT]+[F4], which is used for closing the active window. Record Button: This button is used to generate ‘Record’ command in various media applications. Play Button: This button is used to generate ‘Play’ command in various media applications. Open Button: This button is used to generate ‘File/Folder Open’ command in various media applications. Rewind Button: This button is used to generate ‘Rewind’ command in various media applications. Pause Button: This button is used to generate ‘Pause’ command in various media applications. Fast Forward Button: This button is used to generate ‘Fast Forward’ command in various media applications. Previous Button: This button is used to generate ‘Previous’ command in various media applications. Stop Button: This button is used to generate ‘Stop’ command in various media applications. Next Button: This button is used to generate ‘Next’ command in various media applications. Backspace Button: This button functions identically to the [Backspace] key of the keyboard.
Page 11 Mouse/Keyboard Button: This button is used to toggle Pad controller operation mode. Pressing this button will toggle the mode of the Pad controller between mouse mode and keyboard mode. Select/Space Button: This button functions identically to the [Space] key of the keyboard. Windows Logo (Start) Button: This button opens the start menu and functions like the [Windows Start] key of the keyboard. Pad Controller: This Pad is used to move the mouse pointer in mouse mode, and to input four way arrow keys in the keyboard mode. Windows Menu Button: This buttons opens the menu and functions like the [Menu] key of keyboard. Left Click Button: This button functions as the [Left Click] button of the mouse. Enter Button: This button functions as the [Enter] key of the keyboard. Right Click Button: This button functions as the [Right Click] button of the mouse. Escape Button: This button functions as the [ESC] key of the keyboard. Eject Button: This button is used to open the ODD (CD/DVD) drive of the computer system. Application Launcher Button: This button executes the Application Launcher which can run numerous pre-assigned windows applications and files. Quick Launch Button: This button runs the assigned special application directly. The default assigned application is iMEDIAN. You can change the assigned application in Setup menu of the iMON Manager. Task Switcher Button: This button is used for choosing the application among the current running applications. This feature is similar to the [ALT]+[TAB] keyboard shortcut command. Mute Button: This button is used to mute/unmute the volume. Volume Up/Down Button: This button is used to adjust the volume up or down. Channel Up/Down Button: This button is used to change the channel up or down. Timer Button: This button runs the iMON timer. The iMON timer feature can turn off the computer or set the alarm assigned in Setup. Numeric Button: The numeric buttons from 0 to 9 are custom buttons that can be assigned by users. Shift+Tab Button: This button is used identically to [Shift]+[Tab] of the keyboard.
Page 12 Tab Button: This button functions identically to the [Tab] key of the keyboard. My Movie Button: This button is used to go to the Movie View directly in iMEDIAN, Media Center and Power Cinema. My Music Button: This button is used to go to the Music View directly in iMEDIAN, Media Center and Power Cinema. My Photo Button: This button is used to go to the Photo (picture) View directly in iMEDIAN, Media Center and Power Cinema. My TV Button: This button is used to TV View directly in iMEDIAN, Media Center and Power Cinema. Bookmark Button: This button is used to generate ‘Bookmark’ command in various media applications. Thumbnail Button: This button is used to generate ‘Thumbnail’ or ‘Capture Image’ command in various media applications. Aspect Ratio Button: This button is used to generate ‘Change the Aspect Ratio’ command in various media applications. Full Screen Button: This button is used to generate ‘Full Screen’ command in various media applications. My DVD Button: This button is used to go to the DVD view directly in iMEDIAN, Media Center and Power Cinema. Menu Button: This button is used to generate ‘DVD Menu’ command in DVD applications. Caption Button: This button is used to generate ‘Change the Caption/Subtitle’ command in DVD applications. Language Button: This button is used to generate ‘Change the Language/Audio’ command in DVD applications. Using iMEDIAN iMEDIAN is designed to you enjoy various media files such as music, movies and photos in local and network PC, and use multimedia devices like DVD, TV, digital camcorder and web camera using the Pad remote controller.
Page 13 Connector Panel The connector panel is located on the bottom side of the display unit. (Please remove the connector panel cover to access the connector panel) X Mouse PS/2 Connector The standard PS/2 mouse DIN connector is for a PS/2 mouse. Y Keyboard PS/2 Connector The standard PS/2 keyboard DIN connector is for a PS/2 keyboard. Z DVI Port The DVI (Digital Visual Interface) port allows you to connect a LCD monitor. It provides a high-speed digital interconnection between the computer and its display device. To connect an LCD monitor, simply plug your monitor cable into the DVI connector, and make sure that the other end of the cable is properly connected to your monitor. [ USB Ports Four USB 2.0 ports are available for connection to various peripheral devices. \ Audio Connection Port These audio connectors are used for audio devices. You can differentiate the color of the audio jacks for different audio sound effects. Line-Out (Green }) – Line Out, is a connector for speakers or headphones. Line-In (Blue }) – Line In, is used for external CD player, tape player or other audio devices. Mic (Pink }) – Mic, is a connector for microphones. RS-Out (Black }) – Rear Surround Out in 4, 5.1 and 7.1 channel modes. CS-Out (Orange }) – Center/Subwoofer Out in 5.1 and 7.1 channel modes. SS-Out (Gray }) – Side Surround Out in 7.1 channel mode. ] LAN Port The standard RJ-45 LAN jack is for connection to the Local Area Network (LAN). You can connect a network cable to it. ]X Y Z [ \^
Page 14 LED Color LED State Status Off LAN link not established On (Steady State) LAN link established Left Yellow On (Bright & Pulsing) Communicating with another computer over LAN Off 10 Mbit/sec data rate selected Green On 100 Mbit/sec data rate selected Right Orange On 1000 Mbit/sec data rate selected ^ VGA Port The DB 15-pin female connector is provided for connection to a monitor. NOTE Normally a DB 15-pin cable is already connected to this connector to provide VGA signal to the screen. Please do not disconnect this cable unless you want to change the input signal of the screen to a different source.
Page 15 IInnssttaallllaattiioonn//MMoouunnttiinngg GGuuiiddee Before you start First make sure that the power to each piece of equipment is turned off. Use connecting cables suitable for the equipment to be connected. The cable connectors should be fully inserted into the jacks. A loose connection may cause hum and other noise. To disconnect the cable, pull it out by grasping the plug. Never pull the cable itself. Refer to the connection guide of the operation manual of the equipment to be connected. Insert the plug securely into the AC IN socket. Installation Precautions When installing the VM032, VM042(H) or VM047 series systems, please follow the precautions listed below: Power OFF: When installing the VM032, VM042(H) or VM047 series system(s), make sure the power is off. Failing to turn off the power may cause severe injury to the body and/or damage to the system. Qualified Personnel: Only certified or qualified personnel should install and modify onboard functionalities. Mounting: The VM032, VM042(H) and VM047 series systems are heavy devices. When mounting the system onto a rack, panel, wall or arm, make sure that at least two people are assisting with the procedure. Anti-static Discharge: If a user opens the rear panel of the VM032, VM042(H), or VM047 series system to configure, replace or add peripheral devices, be sure to ground the body first or wear an anti-static wristband. Preinstalled Components The following components are preinstalled in the VM032, VM042(H) and VM047 series systems: Mainboard TFT LCD screen 2 x 1GB DDR2 memory module Wireless LAN module (Optional) Remote control (Optional) DVD±RW drive (Optional) 80GB SATA II hard disk drive NOTE Installation or replacement of some of the components is described in the following sections. Installation and Configuration Steps The following installation steps must be followed: STEP 1 Unpack the VM032, VM042(H) or VM047 series system from its box. STEP 2 Mount the VM032, VM042(H) or VM047 series system. STEP 3 Connect the main power cord and any other peripheral devices to the bottom connector panel of the VM032, VM042(H) or VM047 series system. STEP 4 Turn the power ON and configure the system. Unpacking To unpack the VM032, VM042(H) or VM047 series system(s), follow the instructions below: WARNING! The front side of the LCD screen has a protective plastic cover attached to the screen. Only remove the protective cover after the monitor has been properly installed. This ensures the screen is protected during the installation process.
Page 16 STEP 1 Use a box cutter, a knife, or a sharp pair of scissors to cut the seals on top side of the carbon box. STEP 2 Open the carbon box. STEP 3 Lift the unit carefully out of the box. STEP 4 Remove both polystyrene ends, one from each side. STEP 5 Pull the safety plastic cover off the monitor screen. STEP 6 Make sure all the components listed in the packing list are present. Packing List The VM series monitor is shipped with the following standard components: Quantity Description and Part Number Image 1 VM032, VM042(H) or VM047 Series System (Part number: ) 1 Remote controller (Optional) (Part number: ) 1 Power cord (Part number: ) 1 Wireless LAN antenna (Optional) (Part number: ) 1 Operation manual (Part number: ) 1 Windows™ XP Professional CD (Part number: ) 1 Driver CD (Part number: ) 1 Wall mount (Part number: ) 1 Screw set (Part number: ) Mounting Space Requirements To prevent internal heat buildup from sealing off the display, make sure to ensure proper ventilation by leaving open the minimum amount of space around the display as illustrated below. The ambient temperature must be 0°C to 35°C (32°F to 95°F). When installing the display horizontally, use the optional display stand (not supplied). Installation of hardware such as brackets, screws, or bolts is not specified and is up to the authorized local dealers. Consult with qualified personnel for installation. While the display is on, a certain amount of heat builds up inside. This can cause burns. Avoid touching the top or rear of the unit when it is powered on or just after it has entered standby mode.
Page 17 Mounting the Display Horizontally Mounting the Display Vertically NOTE When mounting the LCD display unit vertically, make sure the POWER switch is at the lower position. Using the Optional Stand (not supplied) NOTE When moving or installing the LCD display unit, it is recommended that at least two people do so to prevent any damage and/or injury to both the display unit and people moving or installing the unit. Front Side4” (100) 4” (100) 9.875” (250mm) 9.875” (250mm) 2” (50mm) Units: inches (cm) Front Side7.875” (200mm) 9.875” (250mm) 9.875” (250mm) 4”(100mm) 2”(50mm) Units: inches (mm) Front Side7.875” (200mm) 4” (100)4” (100) 4” (100mm) Units: inches (mm)
Page 18 Mounting the System Wall Mounting WARNING! 5 Do not begin to install the system until you have read and understood the instructions and warnings contained in this section. 5 Make sure that the supporting surface will safely support the combined load of the system and all attached hardware and components. 5 Never exceed the Maximum Load Capacity of 220 lb (100 kg). 5 If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an “edge to edge” stud finder is highly recommended. 5 Always use an assistant or mechanical lifting equipment to safely lift and position the system. 5 When installing wall mounts on cinder block, verify that you have a minimum of 1-3/8” of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints. Besure to mount in a solid part of the block, generally 1” (25 mm) minimum from the side of the block. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. 5 Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. 5 Concrete anchors are NOT intended for attachment to concrete walls covered with a layer of plaster, drywall, or other finishing materials. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/drywall (up to 5/8” thick) must be counterbored. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8”, custom fasteners must be used. 5 Tighten the screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power. Required Tools Drill, level, 3/16” drill bit, 1/2” masonry bit for brick concrete or concrete block installations, wrench or socket set, Philips screwdriver Parts List AA Wall Plate (1) BB Left monitor bracket (1) CC Right monitor bracket (1) DD Safety bar (1) M4x12 Bolt (4) M5x12 Bolt(4) M6x12 Bolt(4) M8x25 Bolt (4) M4x30 Bolt (4) M5x30 Bolt(4) M6x35 Bolt(4) M8x40 Bolt (4) M4 Lock washer(4) M5 Lock washer(4) M6 Lock washer(4) M8 Lock washer (4) M4/M5 Spacer(4) M6/M8 Spacer(4) M4/M5 Washer(8) M6/M8 Washer (8) Lag bolt (6) Lag bolt washer(6) Concrete Anchor (6)
Page 19 NOTE Not all bolts, lock washers, spacers, and washers are used during the installation. To mount the VM032, VM042(H) or VM047 series system(s) onto the wall, please follow the steps below. Mounting Monitor Brackets to the System STEP 1 The VM042(H) system uses M6x35 bolts for the monitor brackets. Thread the M6x35 bolt through an M6 lock washer, an M6/M8 washer, the monitor bracket (BB/CC) and finally into the monitor system (left). STEP 2 Repeat the above process for the remaining monitor bracket. NOTE Make sure the monitor brackets are vertically centered and level with each other. Mounting the Wall Plate Wood Stud Mounting STEP 1 Select the location on the wall for wall plate. Make sure there are sufficient spacing as mentioned in the previous section between the monitor and walls when selecting the location. STEP 2 The wall plate (AA) must be mounted to two wood studs at least 16” (406mm) apart. Use a stud sensor to locate two adjacent studs. It is a good idea to verify where the studs are located with an awl or thin nail shown left. STEP 3 Pre-drill a 2-1/2” (64mm) deep hole at the desired height in each stud using a 3/16” drill bit. Make sure these holes are in the center area of the studs and level with each other. Use the wall plate as a template to mark the location of the second hole in each stud. STEP 4 Drill 2-1/2” (64mm) deep holes using the 3/16” drill bit in the marked locations. STEP 5 Attach the wall plate to the wall using 4 pieces of 1/4”x2-1/2” lag bolts and 4 pieces of lag bolt washers. Make sure the wall plate is oriented so the flat surface in the center of the plate is against the wall and that a set of lag bolts is on each side of the two large holes in the center as shown above. M6x35 boltM6 lock washerM6/M8 washerStud sensor 16 inches Wall plate
Page 20 Brick, Solid Concrete and Concrete Block Mounting STEP 1 Use the wall plate (AA) as a template to mark six hole locations on the wall. The outer holes must fall to the left and right of the two holes in the middle of the plate; three in the top row of slots and three more in the bottom row. Make sure the holes are level and there is at least 6” (152mm) distance between any two holes. STEP 2 Pre-drill the holes with a 1/2” drill bit to at least 2-1/2” (64mm) in depth. STEP 3 Insert a concrete anchor into each holes that were drilled in the previous step. Make sure the anchor is seated completely flush with the concrete surface. Use a hammer if the anchor does not seat properly. NOTE Concrete anchors are not intended for attachment to concrete walls covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete walls covered with plaster or drywall is unavoidable, plaster/drywall (up to 5/8” thick) must be counterbored as shown below. Hanging the Monitor onto the Wall Plate STEP 1 First hook the monitor brackets over the top of the wall plate as shown left, then let the bottom of the monitor brackets swing in under the bottom of the wall plate. STEP 2 Once the system has been installed properly on the wall plate, the horizontal position of the system can be adjusted. The black knobs on are used to adjust the tilt position of the monitor. Loosen both knobs and adjust the tilt of the monitor until satisfied then tighten both knobs. The monitor can be tilted up or down by 15°. NOTE When loosening the tilt adjustment knobs, the monitor may suddenly tilt downwards and cause injury or damage. Make sure to hold the monitor firmly when adjusting the tilt of the monitor to prevent injury or damage. Wall plateTilt adjustment knob
Page 21 STEP 3 Once the system is in place, insert the safety bar into the slots in the bottom of the monitor brackets so that it sits behind the bottom tab on the wall plate as shown left. The bend at the end of the safety bar should face toward the wall. Once the safety bar passes out the other side of the wall plate, a padlock can be added to the hole at the end of the safety bar for additional security. Using the Monitor Stand (Optional) STEP 1 Using a Philips screwdriver, tighten six screws as shown on the left to install the optional monitor stand. NOTE To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. Place monitor stand bracket on back of screen and align to holes. NOTE The vertical position of the monitor may be adjusted by changing the hole positions. Safety barPadlock hole Bend facing the wall
Page 22 Connecting the AC Power Cord STEP 1 Remove the connector panel cover to reveal the connector panel. Removing the connector panel will reveal the connector panel and the AC power socket. You will also notice the VGA monitor cable that is already connected to the VGA port of the connector panel. STEP 2 Plug the AC power cord into the AC power socket and install the connector panel cover. Connecting the Speakers (Optional) Connector panel coverVGA monitor cable AC power socket AC power cord
Page 23 UUssiinngg OOnn--SSccrreeeenn--DDiissppllaayy ((OOSSDD)) MMeennuuss Operating OSD Menus Menu operating buttons Use the buttons on the LCD display unit for On-Screen Display menu operations. Configuration of the Menu 1. Press MENU. The main menu appears on the screen. 2. Press ©/ª to move the cursor (blue) to the main menu items you want to select and press SELECT. The cursor moves to the next menu. 3. Press ©/ª to move the cursor (blue) to the item you want to select and press SELECT. The menu for the selected item appears and the selected menu turns to pink. Select a different item by repeating this procedure. 4. Press ©/ª to adjust or select the setting press MENU to set it. The setting is registered and the menu returns to the previous menu. To complete the configuration and return to the normal screen, press MENU. To return to the previous menu level, press ©/ª to move the cursor to the main menu section and press SELECT. Menu Select STOSD Control Button Panel Power LED
Page 24 Press SELECT from normal screen at any time for automatic screen adjustment. The screen will flicker for a moment as the screen adjusts automatically to the screen configurations. To Switch the On-Screen Language You can select the desired on-screen language for menus and messages from among 5 different languages. “English” is set as the factory default language. For details on switching the on-screen language, see “Selecting the On-Screen Language” on page 27. Menu Guide NOTE Items that cannot be set or adjusted (depending on the setting or the type of signal input) are shown in dark gray. Color Mode Adjusts the quality of the picture. Select “Color” with ©/ª and press SELECT. Contrast Select “Brightness” with ©/ª and press SELECT. Adjust the contrast with ©/ª within the range of MIN (0) to MAX (100), then press SELECT. ©: Increases the picture contrast. ª: Decreases the picture contrast. Brightness Select “Contrast” with ©/ª and press SELECT. Adjust the brightness with ©/ª within the range of MIN (0) to MAX (100), then press SELECT. ©: Makes the picture brighter. ª: Makes the picture darker. Color Adjust Select “Clock” with ©/ª and press SELECT. Adjust the color for RGB with ©/ª within the range of MIN (0) to MAX (255) for R, B, and B, then press SELECT. Color Temperature Select “Phase” with ©/ª and press SELECT. Adjust the color temperature by selecting 9300, 6500, 5800, or User with ©/ª (If User is selected adjust the set values of each gain with ©/ª). 1. Select the color temperature with ©/ª and press SELECT. 5800: Sets the color temperature to low. 6500: Sets the color temperature to neutral. 9300: Sets the color temperature to high. Red, Green, and Blue: Sets values for each gain separately.
Page 25 2. When you select Red, Green, or Blue, press ©/ª to move the cursor (blue) to the gain that you want to adjust and press SELECT. 3. Adjust the gain (0 to 100) with ©/ª and press MENU. Image Setting Adjusts the quality of the picture. Select “Image Setting” with ©/ª and press SELECT. Clock Select “Clock” with ©/ª and press SELECT. Adjust the clock frequency with ©/ª within the range of MIN (0) to MAX (100), then press SELECT. ©: Increases the clock frequency. ª: Decreases the clock frequency. NOTE The clock mode is only enabled during the PC mode. Phase Select “Phase” with ©/ª and press SELECT. Adjust the phase with ©/ª within the range of MIN (0) to MAX (63), then press SELECT. ©: Moves the display position upward. ª: Moves the display position downward. NOTE The phase mode is only enabled during the PC mode. Gamma Select “Gamma” with ©/ª and press SELECT. Adjust the Gamma level with ©/ª within the range of MIN (0) to MAX (3), then press SELECT. Sharpness Select “Sharpness” with ©/ª and press SELECT. Adjust the sharpness with ©/ª within the range of MIN (0) to MAX (4), then press SELECT. ©: Increases the sharpness of the image. ª: Decreases the sharpness of the image.
Page 26 Position Adjusts the position of the display screen. Select “Position” with ©/ª and press SELECT. H. Position Select “H. (Horizontal) Position” with ©/ª and press SELECT. Adjust the position of the display horizontally with ©/ª within the range of MIN (0) to MAX (100), then press SELECT. ©: Moves the display position right. ª: Moves the display position left. V. Position Select “V. (Vertical) Position” with ©/ª and press SELECT. Adjust the position of the display vertically with ©/ª within the range of MIN (0) to MAX (100), then press SELECT. ©: Moves the display position upward. ª: Moves the display position downward. Fit to Screen Select “Fit to Screen” with ©/ª and press SELECT. Select from 16:9 or 4:3 aspect ratio with ©/ª the press SELECT. OSD Menu From this menu, various on-screen display related options can be controlled and setup. Select “OSD Setup” with ©/ª and press SELECT. OSD H. Position Select “OSD H. (Horizontal) Position” with ©/ª and press SELECT. Adjust the position of the OSD display horizontally with ©/ª within the range of MIN (0) to MAX (100), then press SELECT. ©: Moves the OSD display position right. ª: Moves the OSD display position left. OSD V. Position
Page 27 Select “OSD V. (Vertical) Position” with ©/ª and press SELECT. Adjust the position of the OSD display vertically with ©/ª within the range of MIN (0) to MAX (100), then press SELECT. ©: Moves the OSD display position upward. ª: Moves the OSD display position downward. OSD Timer Select “OSD Timer” with ©/ª and press SELECT. Adjust the OSD display time with ©/ª within the range of MIN (0) to MAX (60), then press SELECT. The on-screen display will automatically disappear after the designated set time in this menu. ©: Increases the OSD display time. ª: Reduces the OSD display time. Language You can select the on-screen language from English, German, French, Spanish and Korean. At the factory, the default language has been setup in English. Select “Language” with ©/ª and press SELECT. Select “Language” with ©/ª and press SELECT. Press ©/ª to the desired language and press SELECT. The on-screen language is switched to the one you have selected. English: English Français: French Deutsch: German Espaňol: Spanish 한국어: Korean Miscellaneous You can select the desired input signal of the display, control volume (Not available in this system) and reset the OSD values to factory default. Select “Misc” with ©/ª and press SELECT.
Page 28 Signal Source Select “Signal Source” with ©/ª and press SELECT. Using ©/ª select DVI or RGB then press SELECT. Volume Select “Volume” with ©/ª and press SELECT. Adjust the volume with ©/ª within the range of MIN (0) to MAX (100), then press SELECT. ©: Increases sound volume. ª: Decreases sound volume. NOTE The volume adjustment is not available in PC mode. Mute Select “Mute” with ©/ª and press SELECT. Using ©/ª select ON or OFF then press SELECT. ON: Mute function is enabled and all sounds are muted. OFF: Mute function is disabled. NOTE The mute feature is not available in PC mode. Reset Select “Reset” with ©/ª and press SELECT. Selecting reset will restore all settings to their factory presettings.
Page 29 SSppeecciiffiiccaattiioonnss System Specifications The technical specifications for the VM032, VM042(H) and VM047 series systems are listed in table below. Mainboard Specifications The VM032, VM042(H) and VM047 series systems come with a MSI P6NGM mainboard. The technical specifications of the mainboard are listed in table below. Flat Panel Screen Specifications Model VM015 VM019 VM032 VM042 VM042H VM047 Screen Size (Diagonal) 15” (381mm) 19” (482.6mm) 32” (812.8mm) 42” (1066.8mm) 42” (1066.8mm) 47” (1193.8mm)Resolution 1024 x 768 1280 x 1024 1366 x 768 1366 x 768 1920 x 1080 1920 x 1080 Active Area (mm) 304.128 x 228.096 376.320 x 301.056 697.6845 x 392.256 930.25 x 523.01 930.24 x 523.26 1039.68 x 584.82 Pixel Pitch (mm) 0.297 x 0.297 0.098 x 0.294 0.51075 x 0.17025 0.227 x 0.681 0.4845 x 0.4845 0.5415 x 0.5415 LCD Colors 16.2 Million 16.2 Million 16.7 Million 16.7 Million 16.7 Million 16.7 Million Viewing Angle 130 / 110 160 / 160 178 / 178 178 / 178 178 / 178 178 / 178 Brightness (cd/m2) 400 300 500 500 500 500 Contrast Ratio 500:1 800:1 1000:1 1000:1 1000:1 1000:1 Response Time 25 msec 10 msec 10 msec 8 msec 8 msec 8 msec Power Consumption 14.6 W 24.0 W 113.7 W 167.4 W 168.8 W 247.2 W Input Voltage 3.3 V 5.0 V 24.0 V 24.0 V 24.0 V 24.0 V Electrical Interface 1ch LVDS 2ch LVDS 1ch LVDS 1ch LVDS 2ch LVDS 2ch LVDS Category Specifications CPU Type Intel® Core™ Solo/Duo or Core™ 2 Duo,Core™ 2 Quad, Pentium™ D, Celeron™CPU Socket LGA775 System Chipset NVIDIA® GeForce 73PV Memory Type DDR2 533/667/800 MHz Memory Slot 2 x DIMM Standard Memory 2 GB (2 x 1 GB) Maximum Memory 4 GB (2 x 2 GB) Ethernet LAN Chip Realtek® RTL 8211BL Audio Chip Realtek® ALC888 Rear Connectors 1 x DVI, 1 x RJ45 LAN, 1 x Azalia Audio Rack, 4 x USB 2.0, 2 x PS/2, Onboard Slots & Internal Connectors 2 x DDR2 DIMM, 4 x SATA II, 1 x PCIe *1, 1 x CD audio in, 2 x Front panel, 6 x USB 2.0, 2 x Cooling fans, 1 x Front audio, Operating System Windows™ XP Pro (Standard) Windows™ Vista™ Premium (Optional)
Page 30 MMaaiinnbbooaarrdd Introduction The VM032, VM042(H) and VM047 series systems contain the MSI P6NGM mainboard. The mainboard is the heart of any computer and is responsible for transmitting, receiving and processing data as well as driving the different onboard devices and peripherals. CPU The MSI P6NGM mainboard comes with a preinstalled Intel® Pentium™ D, Core™ Duo, Core™ 2 Duo, Core™ 2 Quad, P4EE™, or Pentium™ XE processors. The Intel® Core™ Duo and Core™ 2 Duo processors are built on Intel’s next generation 65 nanometer technology with copper interconnect. The Intel® Core Solo processors refers to a single core processor and the Intel® Core™ 2 Duo processor refers to a dual core processor. The table below shows list of processors that can be installed on MSI P6NGM mainboards. NOTE With CPU speed changing rapidly, there might be faster CPUs on the market by the time you receive this operation manual. The applicable processor table is for your reference only. On-Board Chipset The MSI P6NGM mainboard has a preinstalled NVIDIA® GeForce 73PV(7100/NF630i) chipset. The NVIDIA® GeForce 73PV(7100/NF630i) chipset supports Intel’s x86 Core™ 2 Quad processors as well as Core™ 2 Duo, Pentium™ and Celeron™ processors. With a 1333 MHz system bus, DDR memory technology and support for Microsoft® Windows Vista™ Premium, the NVIDIA® GeForce 73PV(7100/NF630i) chipset enables a scalability and performance for everyday computing. NVIDIA® GeForce 7 Series Graphics Processing Unit (GPU) – Industry-leading NVIDIA® GPU delivers better graphics, faster performance, and a great Microsoft® Windows Vista™ experience. Microsoft® Windows Vista™ Premium Capable – NVIDIA® GPU mainboards are ready for Microsoft® Windows Vista™ Premium experience when coupled with 1GB of system memory. Processor Number Clock Speed Front Side Bus Cache Core 2 Quad Q6700 2.66 GHz Core 2 Quad Q6600 2.40 GHz 1066 MHz 8MB L2 Core 2 Duo E6850 3.00 GHz Core 2 Duo E6750 2.66 GHz 1333 MHz Core 2 Duo E6700 2.66 GHz 1066 MHz Core 2 Duo E6550 2.33 GHz Core 2 Duo E6540 2.33 GHz 1333 MHz 4MB L2 Core 2 Duo E6400 2.13 GHz Core 2 Duo E6300 1.86 GHz 1066 MHz Core 2 Duo E4700 2.60 GHz Core 2 Duo E4600 2.40 GHz Core 2 Duo E4500 2.20 GHz Core 2 Duo E4400 2.00 GHz Core 2 Duo E4300 1.80 GHz 2MB L2 Core Duo E2220 2.40 GHz Core Duo E2180 2.00 GHz Core Duo E2160 1.80 GHz Core Duo E2140 1.60 GHz 1MB L2 Pentium D960 3.60 GHz Pentium D950 3.40 GHz Pentium D945 3.40 GHz Pentium D940 3.20 GHz Pentium D935 3.20 GHz Pentium D930 3.00 GHz Pentium D925 3.00 GHz Pentium D915 2.80 GHz 800 MHz 4MB L2
Page 31 Microsoft DirectX 9.0 Shader Model 3.0 Support – Top-notch compatibility and performance for all Microsoft DirectX® 9.0 applications, including Shader Model 3.0 support. Integrated HDMI™ with On-Chip HDCP – On board HDMI™ connector designed to meet the output protection management (HDCP) and security specifications of the Blu-ray Disc and HD DVD formats, allowing the playback of encrypted movie content on PCs when connected to HDCP-capable displays. Integrated DVI with HDCP – Abel to drive flat-panel displays supporting single-link TMDS at 162MHz pixel clock. Designed to meet the output protection management (HDCP) and security specifications of the Blu-ray Disc and HD DVD formats, allowing the playback of encrypted movie content on PCs when connected to HDCP-capable displays. PCI Express – Supports PCI Express bus architecture with full bandwidth x16 expansion slot. NVIDIA® nForce® Storage – Safeguards your most important digital media assets; always reliable, scalable, and accessible. Includes NVIDIA RAID and drive support. NVIDIA® RAID and MediaShield™ Technology – Provides a simple point and click wizard-based interface for creating and managing multi-disk storage configurations. Allows multi-disk designs to be set up for maximum performance (RAID 0), for data protection (RAID 1), or for a combination of both performance and protection (RAID 0+1 and RAID 5). Also allows RAID volumes to be converted from one configuration to another with a single operation. Uniquely allows users to assign an extra disk to any RAID volumes so that should a disk failure occur, NVIDIA® RAID will automatically remove the failed disk and replace it with the spare. SATA 3Gb/s – Take advantage of the latest SATA 3Gb/s hard disk drives, which double bus bandwidth and provides blazingly high disk performance. This technology provides easy-to-install, high-performance but low-powered hard drives. NVIDIA® nForce® Networking – NVIDIA® nForce® Networking solution enables Internet connectivity through industry standard 10/100/1000 Mb/s Ethernet connection. NVIDIA® Native Gigabit Ethernet – The industry’s fastest Gigabit Ethernet performance eliminates network bottlenecks and improves overall system efficiency and performance. NVIDIA® CineFX™ 3.0 Engine – Powers the next generation of cinematic realism. Full support for Microsoft® DirectX® 9.0 Shader Model 3.0 enables stunning and complex special effects. Next-generation shader architecture delivers faster and smoother game play. NVIDIA® nView™ Multi-Display Technology – Advanced technology provides the ultimate in viewing flexibility and control for multiple monitors. NVIDIA® Digital Vibrance Control™ 3.0 Technology – Allows the user to adjust color controls digitally to compensate for the lighting conditions of their workspace, in order to achieve accurate, bright colors in all conditions. OpenFL® 1.5 Optimizations and Support – Top-notch compatibility and performance for all OpenGL® applications. 300 MHz RAMDAC – Blazing-fast RAMDAC supports the display with high, ergonomic refresh rates up to and including 1920x1440 @ 75MHz. DDR2 Memory Architecture – A state-of-the-art DDR2 memory controller allows high bandwidth and low latency data access to the CPU. Enables data and information to be relayed through the system as quickly as possible for incredible performance. Supports up to 4 GB of system memory. High Definition Audio (HDA) – High definition audio brings consumer electronics quality sound to the PC delivering high quality sound from multiple channels. Using HAD, systems can deliver 192 kHz/32-bit quality for eight channels, supporting new audio formats. USB Ports – A standard plug-and-play interface that provides easy-to-use connectivity for USB devices. Supports up to 10 USB 1.1/2.0 ports. Peripheral Device Interfaces, Connectors and Slots The peripheral device connectors, interfaces and slots on the MSI P6NGM mainboard are listed in the sections below. Internal Slots The slots listed below can all be found on the MSI P6NGM mainboard.
Page 32 2 x 240-pin DDR2 DIMM slots 1 x PCI (Peripheral Component Interconnect) express x1 slot 1 x PCI (Peripheral Component Interconnect) express x16 slot 2 x PCI (Peripheral Component Interconnect) slots Internal Peripheral Device Connectors The peripheral device connectors listed below are located on the MSI P6NGM mainboard and used for the VM series. 1 x SPDIF(Sony & Philips Digital Interconnect Format)-out pinheader 1 x Serial port pinheader 1 x Floppy disk drive connector 4 x Serial ATA II connectors 1 x IDE connector 6 x USB 2.0 connectors 1 x Front audio connector 1 x CD audio in connector 2 x Front panel connector (Power and reset switch connectors) External Peripheral Device Connectors The peripheral device connectors listed below are located on the MSI P6NGM mainboard. 1 x PS/2 keyboard 1 x PS/2 mouse 4 x USB 2.0 ports 1 x 2 in 1 audio jack 1 x RJ45 LAN port 1 x DVI connector 1 x VGA port CPUMemory SlotsPower Connection (24 pins)SATA ConnectorsPCI SlotsUSB 2.0 ConnectorsCPU FanSystem Fan PowerIDE ConnectorPCI Express x1 SlotFront Panel ConnectorsCPU PowerPCI Express x16 SlotFDD ConnectorSerial Port Connector
Page 33 SSyysstteemm MMaaiinntteennaannccee System Maintenance Introduction If the components such as memory or hard disk drive of VM032, VM042(H) and VM047 series systems fail, they must be replaced by qualified personnel. Please contact the local dealer or vendor to purchase or replace the parts. Procedures for the rear cover removal and jumper settings for the VM032, VM042(H) and VM047 series systems are described in sections below. Mainboard Replacement Although the mainboard will not fail under normal usage, if it does fail, the mainboard needs to be replaced by qualified personnel or be returned to the local dealer or vendor for replacement. Please contact the local dealer or vendor for the replacement of the mainboard. NOTE Any attempt to remove and replace the mainboard voids warranty, and the local dealer, vendor, and manufacturer are not responsible for any consequential damages and injuries. Mainboard Access Panel Removal WARNING! BEFORE REMOVING THE REAR COVER, MAKE SURE THE POWER CORD HAS BEEN DISCONNECTED FROM THE SYSTEM. Failing to do so may lead to severe damages of the VM series monitors and injury to the body. WARNING! PLEASE TAKE ANTISTATIC PRECAUTIONS WHEN WORKING WITH THE INTERNAL COMPONENTS. The interior of VM series monitors contain very sensitive electronic components. These components are prone to electrostatic discharge (ESD). Before working with the internal components, make sure all antistatic precautions have been observed. X Connector panel cover Y Mainboard access panel Z Rear panel [ DVD drive housing There are two rear panels on the back of the VM032, VM042(H) and VM047 series systems. The rear panel (Y)in the center secured by 6 screws allows easy access to various computer components such as the mainboard and hard disk drive and is referred to as the mainboard access panel. This removal of this panel allows access to all major computer components and although the user will not normally need to remove this panel, this panel is the only panel that needs to be removed for access to the mainboard and hard disk drive. The large rear panel (Z) needs to be removed in order to gain access to the following components: AD board Mainboard power supply SMPS for LCD panel Y Z X [
Page 34 Mainboard Access Panel Removal In order to remove the mainboard access panel and gain access to various computer components, the connector panel cover (X) needs to be removed first. Step 1 Unscrew 6 thumb screws holding the connector panel cover. Remove the connector panel. Step 2 Unscrew 6 screws holding the mainboard access panel (Y) using a Philips screwdriver. Remove the mainboard access panel to access the various computer components inside. After removing the mainboard access panel, you will have access to the mainboard and hard disk drive. Please see the section for component replacement for procedures on hard disk drive replacement. NOTE PLEASE REMOVE THE CONNECTOR PANEL COVER (X) BEFORE ATTEMPTING TO REMOVE THE MAINBOARD ACCESS PANEL (Y). Any attempt to remove the mainboard access panel without removing the connector panel cover may damage the panels in doing so. Connector panel cover XMainboard access panel Y Hard Disk DriveMainboard Mainboard access panel
Page 35 Rear Panel Removal To remove the rear panel, follow the following steps. Step 1 Unscrew the wireless LAN antenna located on the rear panel. Step 2 Remove 2 thumb screws holding the connector panel cover. Step 3 Using a Philips screwdriver, unscrew the 12 screws holding the large rear panel as shown in the drawing on the left. NOTE Be sure to remove any wall mount before proceeding with the removal of the rear panel. The following components are accessible once the large rear panel ([) has been removed. Mainboard Hard disk drive SMPS PC power supply NOTE Be sure to lay the unit flat facing the floor before removing the rear panel. (The mainboard access panel will be attached to the rear panel when it is removed.) Rear panel Z Hard disk drive AD board Mainboard SMPS PC Power Supply Wireless LAN antenna (Antenna not shown)
Page 36 Component Replacements The following sections cover the replacement procedures for various components inside the VM032, VM042(H) and VM047 series monitors. Only qualified personnel should perform the replacement work. Hark Disk Drive Replacement Step 1 Remove the mainboard access panel following the procedures in the previous section. Step 2 Using a Philips screwdriver, unscrew 4 screws from the protective housing that holds the hard disk drive. Once the screws have been removed, lift out the entire hard disk drive assembly. Step 3 Using a Philips screwdriver, unscrew the 4 screws holding the hard disk drive as shown in the drawing on the left. Once the screws have been removed, remove the rubber rings holding the hard disk drive in place. (Be sure to keep the rubber rings in safe place after removal.) Step 4 Remove the hard disk drive from the protective housing. NOTE Repeat the above procedures in reverse to install the hard disk drive. Memory Module Replacement The DIMM slots located on the mainboard are used for memory modules. (Please refer to the section on ‘Internal Peripheral Device Connectors’ in previous section to locate the DIMM slots on the mainboard.) The following types of memory modules can be used: PC4300 DDR2 RAM (DDR-533) PC5300 DDR2 RAM (DDR-667) PC6400 DDR2 RAM (DDR-800) PC8500 DDR2 RAM (DDR-1066) Hard disk drive Protective Housing
Page 37 To remove the memory module from the DIMM slot(s), follow the following steps. Step 1 Flip the plastic clips at each side of the DIMM slot outward and the memory module will pop up. Step 2 Hold the memory module with both hands and bring it upward to remove it completely from the DIMM slot. To install a new memory module, follow the following steps. Step 1 Flip the plastic clips at each side of the DIMM slot outward before installing the memory module. Step 2 Hold the memory module with both hands and insert it vertically into the DIMM slot. Then push it in until the golden finger on the memory module is deeply inserted in the DIMM slot (The golden finger can barely be seen if the memory module is properly inserted in the DIMM slot). NOTE The memory module has only one notch in the center and will only fit in the right orientation. Step 3 The plastic clips at each side of the DIMM slot will automatically close when the memory module is inserted, but make sure the plastic clips have completely closed and locked in place. NOTE 1) DDR2 memory modules are not interchangeable with DDR memory modules and they are not backwards compatible. You should always install DDR2 memory modules in DDR2 DIMM slots. 2) To enable successful system boot-up, always insert the memory modules into the DIMM1 slot first. DVD Drive Replacement In order to remove the DVD drive, follow the instructions below. Step 1 Using a Philips screwdriver, unscrew 6 screws holding the DVD drive housing from the main rear panel. Step 2 With the DVD drive housing still in place, unscrew 4 screws holding the DVD drive itself from the DVD drive housing using a Philips screwdriver. (Do not remove the DVD drive housing when unscrewing since the DVD drive is still connected internally to the mainboard.) Plastic clips
Page 38 Step 3 Once all the screws in steps 1 and 2 have been removed, lift the DVD drive housing and remove it from the main rear panel. Step 4 Pull out the DVD drive carefully from its position. The DVD drive will have two cables (power and SATA cables) connected to it. NOTE Do not exert too much force when pulling out the DVD drive since the length of the cables are limited and too much force can damage the cables and/or connectors and the cables may also come loose from the mainboard. Step 5 Looking at the rear of the DVD drive, remove the power cable and SATA cable from the DVD drive. Power cable DVD drive SATA cable
Page 39 BBIIOOSS SSeettuupp Entering Setup Power on the computer and unit using the main power switch and the system will begin the POST (Power On Self Test) process. When the message below appears on the screen, press <DEL> key to enter the setup menu. Press DEL to enter SETUP If the message appears before you respond and you still wish to enter Setup, restart the system by turning it OFF and On. You may also restart the system by simultaneously pressing <Ctrl>, <ALT>, and <Delete> keys. Control Keys <u> Move to the previous item <v> Move to the next item <s> Move to the item in the left hand <t> Move to the item in the right hand <Enter> Select the item <ESC> Jumps to the Exit menu or returns to the main menu from a sub-menu <+/Page Up> Increase the numeric value or make changes <-/Page Down> Decrease the numeric value or make changes <F6> Load optimized default values <F10> Save all the CMOS changes and exit Getting Help After entering the Setup menu, the first menu you will see is the Main Menu. Main Menu The main menu lists the setup functions you can make changes to. You can use the arrow keys (u/v/s/t) to select the item. The on-line description of the highlighted setup function is displayed at the bottom of the screen. Sub-Menu If you find a right pointer symbol appears to the left of certain fields that means a sub-menu can be launched from this field. A sub-menu contains additional options for a field parameter. You can use arrow keys () to highlight the field and you can press <Enter> to call up the sub-menu. Then you can use the control keys to enter the values and move from field to field within a sub-menu. If you want to return to the main menu, just press the <ESC> key. General Help <F1> The BIOS setup program provides a General Help screen. You can call up this screen from any menu by simply pressing <F1>. The Help screen lists the appropriate keys to use and the possible sections for the highlighted item. Press <ESC> to exit the Help screen.
Page 40 The Main Menu Standard CMOS Features Use this menu for basic system configurations such as time, date, etc. Advanced BIOS Features Use this menu to setup the items of AMI® special enhanced features. Integrated Peripherals Use this menu to specify your settings for integrated peripherals. Power Management Setup Use this menu to specify your settings for power management PnP/PCI Configurations This entry appears if your system supports PnP/PCI. H/W Monitor This entry shows your PC health status Frequency/Voltage Control Use this menu to specify your settings for frequency/voltage control and overclocking. Load Fail-Safe Defaults Use this menu to load the default values set by the BIOS vendor for stable system performance. Load Optimized Defaults Use this menu to load the default values set by the mainboard manufacturer specifically for optimal performance of the mainboard. BIOS Setting Password Use this menu to set the password for BIOS. Save & Exit Setup Save changes to CMOS and exit setup.
Page 41 Exit Without Saving Abandon all changes and exit setup. Standard CMOS Features The items in Standard CMOS Features Menu include some basic setup items. Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item. Date (MM:DD:YY) This allows you to set the system to the date that you want (usually the current date). The format is <day> <month> <date> <year>. Day Day of the week, from Sun to Sat, determined by BIOS. Read-only. Month The month from Jan to Dec. Date The date from 1 to 31 can be keyed in by numeric keys Year The year can be adjusted by users. Time (HH:MM:SS) This allows you to set the system time that you want (usually the current time). The time format is <hour> <minute> <second>. IDE Primary Master/Slave, SATA 1~4 Press <Enter> to enter the sub-menu and the following screen appears.
Page 42 Device / Vendor / Size Shows the device information that you connected to the SATA connectors. LBA/Large Mode This allows you to enable or disable the LBA Mode. Setting to Auto enables LBA mode if the device supports it and the devices are not already formatted with LBA mode disabled. DMA Mode Selects the DMA mode. Hard Disk S.M.A.R.T. This allows you to activate the S.M.A.R.T. (Self-Monitoring Analysis & Reporting Technology) capability for the hard disks. S.M.A.R.T. is a utility that monitors your disk status to predict hard disk failure. This gives you an opportunity to move data from a hard disk that is going to fail to a safe place before the hard disk becomes offline. NOTE IDE Primary Master/Slave and Serial-ATA 1/2/3/4 Channels appear when you connect the HD devices to the IDE/SATA connectors on the mainboard. Floppy A This item allows you to set the type of floppy drives installed. Available options: [None], [360K, 5.25 in.], [1.2M, 5.25 in.], [720K, 3.5 in.], [1.44M, 3.5 in.], [2.88M, 3.5 in.]. System Information Press <Enter> to enter the sub-menu and the following screen appears. This sub-menu shows the CPU information, BIOS version and memory status of your system (read-only).
Page 43 Advanced BIOS Features Boot Sector Protection This function protects the BIOS from accidental corruption by unauthorized users or computer viruses. When enabled, the BIOS’ data cannot be changed when attempting to update the BIOS with a Flash utility. To successfully update the BIOS, you will need to disable this Flash BIOS Protection function. You should enable this function at all times. The only time when you need to disable it is when you want to update the BIOS. After updating the BIOS, you should immediately re-enable it to protect it against viruses. Full Screen LOGO Display This item enables you to show the company logo on the bootup screen. Settings are: [Enabled] Shows a still image (logo) on the full screen at boot. [Disabled] Shows the POST messages at boot. Quick Booting Setting this item to [Enabled] allows the system to boot within 10 seconds since it will skip some check items. Boot Up Num-Lock LED This setting is to set the Num Lock status when the system is powered on. Setting to [On] will turn on the Num Lock key when the system is powered on. Setting to [Off] will allow users to use the arrow keys on the numeric keypad. IOAPIC Function This field is used to enable or disable the APIC (Advanced Programmable Interrupt Controller). Due to compliance with PC2001 design guide, the system is able to run in APIC mode. Enabling APIC mode will expand available IRQ resources for the system. MPS Table Version This field allows you to select which MPS (Multi-Processor Specification) version to be used for the operating system. You need to select the MPS version supported by your operating system. To find out which version to use, consult the vendor of your operating system.
Page 44 CPU Feature Press <Enter> to enter the sub-menu and the following screen appears: Hyper-Threading Technology This field appears only when the CPU supports Hyper-Threading. The processor uses Hyper-Threading technology to increase transaction rates and reduces end-user response times. The technology treats the two cores inside the processor as two logical processors that can execute instructions simultaneously. In this way, the processor will use only one core to execute the instructions. Execute Bit Support Intel’s Execute Disable Bit functionality can prevent certain classes of malicious “buffer overflow” attacks when combined with a supporting operating system. This functionality allows the processor to classify areas in memory by where application code can execute and where it cannot. When a malicious worm attempts to insert code in the buffer, the processor disables code execution, preventing damage or worm propagation. Set Limit CPUID MaxVal to 3 The Max CPUID Value Limit is designed to limit the listed speed of the processor to older operating systems. Chipset Feature Press <Enter> to enter the sub-menu and the following screen appears: HPET The HPET (High Precision Event Timers) is a component that is part of the chipset. You can enable it and it will provide you with the means to get to it via the various ACPI methods. VGA Share Memory Size The system shares memory to the onboard VGA card. This setting controls the exact memory size shared to the VGA card. DVMT Mode Select This item allows you to set the mode for the graphics core. [Fixed Mode], a fixed-size fragment of the system memory is allocated to the graphics core. It can only be used by the graphics core. [DVMT Mode], the driver of the graphics core uses the system memory like any other OS component or application does. Boot Sequence Press <Enter> to enter the sub-menu and the following screen appears:
Page 45 1st Boot Device This allows you to set the first boot device when BIOS attempts to load the disk operating system. Boot From Other Device Setting this option to [Yes] allows the system to try to boot from other device. If the system fails to boot from this device, it will attempt to boot from the selected first boot device, second boot device then finally the third boot device. Trusted Computing Press <Enter> to enter the sub-menu and the following screen appears: TCG/TPM Support This field is used to enable or disable TPM (Trusted Platform Module) support in BIOS. TPM Enable/Disable Status, TPM Owner Status These items show the status of TPM (read-only). Integrated Peripherals USB Controller This setting allows you to enable/disable the onboard USB controller. USB Device Legacy Support Select [Enabled] if you need to use a USB-interfaced device in the operating system.
Page 46 Onboard LAN Controller This item is used to enable/disable the onboard LAN controller. LAN Option ROM This item is used to decide whether to invoke the Boot ROM of the LAN controller. Audio Controller This setting is used to enable/disable the onboard audio controller. On-Chip ATA Devices Press <Enter> to enter the sub-menu and the following screen appears: On-Chip IDE Controller These items allow users to enable or disable the IDE controller. PCI IDE BusMaster This item allows you to enable/disable BIOS to use PCI busmastering for reading/writing to IDE drives. On-Chip SATA Controller These items allow users to enable or disable the SATA controller. I/O Devices Press <Enter> to enter the sub-menu and the following screen appears: COM Port 1 Select an address and corresponding interrupt for the first serial port. Parallel Port This item allows you to set the parallel port. Parallel Port Mode This item allows you to select the parallel port mode. Parallel IRQ This item allows you to set parallel IRQ.
Page 47 Power Management Setup ACPI Function This item is used to activate the ACPI (Advanced Configuration and Power Management Interface) Function. If your operating system is ACPI-aware, such as Windows 2000/SP, select [Enabled]. ACPI Standby State This item specifies the power saving modes for ACPI function. If your operating system supports ACPI, such as Windows 2000/XP, you can choose to enter the Standby mode in S1 (POS) or S3 (STR) fashion through the setting of this field. Settings are: [S1] The S1 sleep mode is a low power state. In this state, no system context is lost (CPU or chipset) and hardware maintains all system context. [S3] The S3 sleep mode is a lower power state where the information of system configuration and open application/files is saved to main memory that remains powered while most other hardware components turn off to save energy. The information is stored in memory will be used to restore the system when a “wake up” event occurs. Suspend Time Out (Minute) If system activity is not detected for the length of time specified in this field, all devices except CPU will be shut off. Power Button Function This feature sets the function of the power button. Settings are: [On/Off] The power button functions as normal power off button. [Suspend] When you press the power button, the computer enters the suspend/sleep mode, but if the button is pressed for more than four seconds, the computer is turned off. Restore On AC Power Loss This item specifies whether your system will reboot after a power failure or interrupt occurs. Settings are: [Off] Always leaves the computer in the power off state.
Page 48 [On] Always leaves the computer in the power on state. [Last State] Restores the system to the status before power failure or interrupt occurred. Wakeup Event Setup Press <Enter> and the following sub-menu appears: Resume From S3 By USB Device This item allows the activity of the USB device to wake up the system from S3 (Suspend to RAM) sleep state. Resume From S3 By PS/2 Keyboard This setting determines whether the system will be awakened from what power saving modes when input signal of the PS/2 keyboard is detected. Keyboard Power On Function This item allows you to specify a key from the keyboard to power on the system. Resume From S3 By PS/2 Mouse This setting determines whether the system will be awakened from what power saving modes when input signal of the PS/2 mouse is detected. Resume By PCI Device (PME#) When set to [Enabled], the feature allows your system to be awakened from the power saving modes through any event on PME (Power Management Event). Resume By PCI-E Device When set to [Enabled], the feature allows your system to be awakened from the power saving modes through any event on PCI-E device. Resume By RTC Alarm This field is used to enable or disable the feature of booting up the system on a scheduled time/date.
Page 49 PNP/PCI Configurations This section describes configuring the PCI bus system and PnP (Plug & Play) feature. PCI, or Peripheral Component Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its special components. This section covers some very technical items and it is strongly recommended that only experienced users make any changes to the default settings. Primary Graphic’s Adapter This setting specifies which graphics card is your primary graphics adapter. PCI Latency Timer This item controls how long each PCI device can hold the bus before another takes over. When set to higher values, every PCI device can conduct transactions for a longer time and thus improve the effective PCI bandwidth. For better PCI performance, you should set the item to higher values. PCI Slot 1/2 IRQ These items specify the IRQ line for each PCI slot. IRQ Resource Setup Press <Enter> to enter the sub-menu and the following screen appears: IRQ 3/4/5/7/9/10/11/14/15 These items specify the bus where the specified IRQ line is used. The settings determines if AMIBIOS should remove an IRQ from the pool of available IRQs passed to devices that are configurable by the
Page 50 system BIOS. The available IRQ pool is determined by reading the ESCD NVRAM. If more IRQs must be removed from the IRQ pool, the end user can use these settings to reserve the IRQ by assigning a [Reserved] setting to it. Onboard I/O is configured by AMIBIOS. All IRQs used by onboard I/O are configured as [Available]. If all IRQs are set to [Reserved], and IRQ 14/15 are allocated to the onboard PCI IDE, IRQ 9 will still be available for PCI and PnP devices. NOTE IRQ (interrupt Request) lines are system resources allocated to I/O devices. When an I/O device needs to gain attention of the operating system, it signals this by causing an IRQ to occur. After receiving the signal, when the operating system ready, the system will interrupt itself and perform the service required by the I/O device. H/W Monitor Chassis Intrusion The field enables or disables the feature of recording the chassis intrusion status and issuing a warning message if the chassis is once opened. To clear the warning message, set the field to [Reset]. The setting of the field will automatically return to [Enabled] later. CPU/SYS Smart Fan Target The mainboard provides the Smart Fan function which can control the CPU/System fan speed automatically depending on the current temperature to keep it with in a specific range. You can select a fan target value here. If the current CPU/System fan temperatures reach the target value, the smart fan function will be activated. It provides several selections to speed up or cool down automatically. PC Health Status CPU/System Temperature, CPU FAN/SYS FAN1 Speed, CPU Vcore, 3.3V, 5V, 12V, 3VSB These items display the current status of all the monitored hardware devices/components such as CPU voltage, temperatures and all fans’ speeds.
Page 51 Frequency/Voltage Control NOTE Do NOT change these settings unless you are familiar with the chipset. Current CPU/DRAM Frequency These items show the current clocks of CPU and Memory speed. Read-only. Intel® EIST The Enhanced Intel® SpeedStep Technology allows you to set the performance level of the microprocessor whether the computer is running on battery or AC power. This field will appear after you installed the CPU which supports speedstep technology. Advanced DRAM Configuration Press <Enter> to enter the sub-menu and the following screen appears: Configuration of DRAM Timing by SPD Setting to [Enabled] enables DRAM CAS# Latency to be automatically determined by BIOS based on the configurations of the SPD (Serial Presence Detect) EEPROM on the DRAM module.
Page 52 DRAM CAS# Latency When the Configuration DRAM Timing by SPD sets to [Disabled], the field is adjustable. This controls the CAS latency, which determines the timing delay (in clock cycles) before SDRAM starts a read command after receiving it. DRAM RAS# to CAS# Delay When the Configuration DRAM Timing by SPD sets to [Disabled], the field is adjustable. When DRAM is refreshed, both rows and columns are addressed separately. This setup item allows you to determine the timing of the transition from RAS (row address strobe) to CAS (column address strobe). The smaller the clock cycles, the faster the DRAM performance. DRAM RAS# Precharge When the Configuration DRAM Timing by SPD sets to [Disabled], this field is adjustable. This field is adjustable. This setting controls the number of cycles for Row Address Strobe (RAS) to be allowed for precharge. If insufficient time is allowed for the RAS to accumulate its charge before DRAM refresh, refresh may be incomplete and DRAM may fail to retain data. This item applies only when synchronous DRAM is installed in the system. DRAM RAS# Activate to Precharge When the Configuration DRAM Timing by SPD sets to [Disabled], this field is adjustable. This field is adjustable. This setting controls the number of cycles for Row Address Strobe (RAS) to be allowed for precharge. If insufficient time is allowed for the RAS to accumulate its charge before DRAM refresh, refresh may be incomplete and DRAM may fail to retain data. This item applies only when synchronous DRAM is installed in the system. DRAM TRFC When the Configuration DRAM Timing by SPD sets to [Disabled], the field is adjustable. This setting determines the time RFC takes to read from and write to a memory cell. DRAM TWR When the Configuration DRAM Timing by SPD sets to [Disabled], the field is adjustable. Minimum time interval between end of write data burst and the start of a precharge command. Allows sense amplifiers to restore data to cells. DRAM TWTR When the Configuration DRAM Timing by SPD sets to [Disabled], the field is adjustable. Minimum time interval between end of write data burst and the start of a column-read command. It allows I/O gating to overdrive sense amplifiers before read command starts. DRAM TRRD When the Configuration DRAM Timing by SPD sets to [Disabled], the field is adjustable. Specifies the active-to-active delay of different banks. Time interval between a read and a precharge command. DRAM TRTP When the Configuration DRAM Timing by SPD sets to [Disabled], the field is adjustable. Time interval between a read and a precharge command. FSB/Memory Ratio This item will allow you to adjust the FSB/Ratio of memory. Adjusted DDR Memory Frequency It shows the adjusted DDR memory frequency. Read-only. Auto Disable DIMM/PCI Frequency When set to [Enabled], the system will remove (turn off) clocks from empty DIMM and PCI slots to minimize the electromagnetic interference (EMI). Memory Voltage (V) This item will allow you to adjust the Memory voltage.
Page 53 PCI Express Voltage This item will allow you to adjust the PCI Express voltage. Spread Spectrum When the mainboard’s clock generator pulses, the extreme values (spikes) of the pulses create EMI (Electromagnetic Interference). The Spread Spectrum function reduces the EMI generated by modulating the pulses so that the spikes of the pulses are reduced to flatter curves. If you do not have any EMI problem, leave the setting at Disabled for optimal system stability and performance. But if you are plagued by EMI, set to Enabled for EMI reduction. Remember to disable Spread Spectrum if you are overclocking because even a slighter jitter can introduce a temporary boost in clock speed which may just cause your overclocked processor to lock up. NOTE 1. If you do not have any EMI problem, leave the setting at [Disabled] for optimal system stability and performance. Bit if you are plagued by EMI, select the value of Spread Spectrum for EMI reduction. 2. The greater the Spread Spectrum value is, the greater the EMI is reduced, and the system will become less stable. For the most suitable Spread Spectrum value, please consult your local EMI regulation. 3. Remember to disable Spread Spectrum if you are overclocking because even a slight jitter can introduce a temporary boost in clock speed which may just cause your overclocked processor to lock up. Load Fail-Safe/Optimized Defaults The two options on the main menu allow users to restore all of the BIOS settings to the default Fail-Safe or Optimized values. The Optimized Defaults are the default values set by the mainboard manufacturer specifically for optimal performance of the mainboard. The Fail-Safe Defaults are the default values set by the BIOS vendor for stable system performance. When you select Load Fail-Safe Defaults, a message appears as below: Pressing [Ok] loads the BIOS default values for the most stable, minimal system performance. When you select Load Optimized Defaults, a message as below appears: Pressing [Ok] loads the default factory settings for optimal system performance. BIOS Setting Password When you select this function, a message as below will appear on the screen:
Page 54 Type the password, up to six characters in length, and press <Enter>. The password typed now will replace any previously set password from CMOS memory. You will be prompted to confirm the password. Retype the password and press <Enter>. You may also press <ESC> to abort the selection and not enter a password. To clear a set password, just press <Enter> when you are prompted to enter the password. A message will show up confirming the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup without entering any password. When a password has been set, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized perform from changing any part of your system configuration.
Page 55 TTrroouubblleesshhoooottiinngg Before requesting service, please check the following points. If the problem persists, contact your local dealer or vendor. Problem Cause Remedy A different input is selected. Using the On-Screen Display controls, check the input selection. Loose VGA cable Open the connector panel cover and check the VGA cable connection. No picture (Power indicator is lit) Computer standby mode Go to control panel in Windows and check the power savings configuration. No picture (Power indicator is not lit) Loose power cord Check the power cord connection to the power outlet. Open the connector panel cover and check the power cord connection. Colors do not display properly. Loose VGA cable Open the connector panel cover and check the VGA cable connection. Screen saver activation Go to control panel in Windows and check the screen saver configuration. Display power or screen turns off after a short time. Computer standby mode Go to control panel in Windows and check the power savings configuration. Horizontal lines of static disturb the picture. The internal temperature of the display is getting high. Turn off the power and make sure the air vents are not blocked, that there is ample space for air to flow around the display, and that the ventilation in the room is working properly. When the internal temperature returns to normal, the display will operate properly again. Something is blocking the remote control signal detector on the display. Make sure no object is blocking the remote control receiver located in the front of the display. Remote control does not work The batteries in the remote control are drained. Replace the batteries in the remote control.
Page 56 SSooffttwwaarree DDrriivveerrss Mainboard Drivers Mainboard INF Drivers VGA Driver Soundcard Driver Network Driver Additional Drivers iMON Remote Control (Optional) Optional Drivers

Navigation menu