VTech Telecommunications 80-0144-00 1.9GHz DECT Baby Monitor - Baby Unit User Manual DM223 CIB V1 20151012

VTech Telecommunications Ltd 1.9GHz DECT Baby Monitor - Baby Unit DM223 CIB V1 20151012

User Manual

Adjust the sound sensitivity of the baby unitYou can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit. The sound sensitivity is preset to LEVEL 5. Sound sensitivity table for referenceDisplay Sensitivity Description High sensitivity levelThe parent unit speaker is constantly on, and you will hear all sounds (including background noises) from your baby’s room. Medium high sensitivity levelThe parent unit speaker turns on for soft babbling and louder sounds from your baby. It remains quiet when your baby sleeps soundly. Medium sensitivity levelThe parent unit speaker turns on for loud babbling and louder sounds from your baby. It remains quiet when your baby makes soft sounds. Medium low sensitivity levelThe parent unit speaker turns on for crying and louder sounds from your baby. It remains quiet when your baby makes soft sounds. Low sensitivity levelThe parent unit speaker turns on for loud crying or screeching sounds from your baby. It remains quiet when your baby makes soft sounds.Press MENU when the parent unit is not in use.Press SELECT.Press VOL. or VOL. to choose the sensitivity level.Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone.1.2.3.4.Install the battery as shown below.NOTEMake sure the supplied rechargeable battery with the label THIS SIDE UP facing up.•User’s manualDM223/DM223-2Safe & Sound® Digital Audio MonitorBCThe parent unit runs on rechargeable battery or AC power. To continuously monitor your baby, make sure you use both battery and AC power at the same time. With the battery alone, the parent unit can cordlessly run for a short time only.NOTESUse only the battery supplied with this product.If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage.Without AC power charging, the battery gradually discharges, even when the parent unit is switched off.•••Install the batteryReplace the batteryTo replace the battery, unplug the battery connector from the socket, and then pull the battery out of the battery compartment. Follow the steps above to install the battery.Charge the parent unit batteryOnce you have connected the parent unit or installed its battery, it powers on automatically. The battery icon indicates the battery status (see the following table).NOTESThe parent unit battery is fully charged after 11 hours of continuous charging.It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging.The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.Battery indicatorsBattery statusActionThe battery icon is off.No battery is installed. The parent unit can be used only when it is connected to AC power.Install the parent unit battery. Charge without interruption (at least 30 minutes).LOW BATTERY and flash on the screen. The light flashes.The battery has very little charge and may be used for only a short time.Charge without interruption (about 30 minutes).The battery icon becomes solid .The battery is fully charged.To keep the battery charged, connect it to AC power when not in use.•••NOTEThis baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be used as such.You may test the baby monitor before initial use, and at regular times thereafter. Place the parent unit and the baby unit in he same room to test the product.Test your audio monitorSpeak towards the microphone of the baby unit. You will hear the sound at the parent unit, and see the visual sound indicators light up.TIPIncrease the speaker volume of the parent unit if you cannot hear the sounds transmitted from the baby unit. NOTESMake sure the baby unit is at least 1 meter (3 feet) away from the parent unit.If no connection can be established, the parent unit displays NOT LINKED and flashes.Positioning the baby monitorCAUTIONKeep the baby unit out of the reach of the baby. Never place or mount the baby unit inside the baby’s crib or playpen.Do not expose the baby unit to extreme heat or direct sunlight.•••••••Before useBaby unit overview1VOL. Press to decrease the speaker volume.•2Microphone 3NIGHT LIGHTPress to turn the night light on or off.•4Night lightOn when night light is turned on.•5POWER lightOn when the baby unit is turned on.•6VOL. Press to increase the speaker volume.•7POWERPress and hold to power on or off.•8PAGEPress to start or stop paging parent unit.•9Power jack10 SpeakerParent unit overview1Microphone2VOL. Press to decrease the speaker volume.While in a menu, press to scroll down. ••3Speaker4MENU/Press to enter the menu while idle.While in a menu, press to return to the previous screen.Press to return to idle screen.•••5Visual sound indicator The visual sound indicator has two functions. One is to show the sound level detected by the baby unit. The other one is to show the volume level during speaker volume setting.Sound level detected by the baby unit One to three green lights indicate a moderate sound level detected by the baby unit. Additional red lights indicate a higher sound level detected by the baby unit (e.g. baby crying loudly).Speaker volume level One to three green lights indicate Level 1 to Level 3 of the speaker volume setting. Additional red lights indicate Level 4 to Level 5 of the speaker volume setting.••••6LCD panelOverview7 Battery level indicatorLight on when the battery is being charged.Light flashes when the battery is low and needs charging.Light off when no battery is installed. •••8VOL. Press to increase the speaker volume.While in a menu, press to scroll up.••9SELECT While in a menu, press to choose an item, or save a setting. •10 (On/off)Press and hold to power on or off.While in a menu, press to return to idle screen. ••11 TALKPress and hold to talk to the baby unit; release to stop talking.While in a menu, press to return to idle screen. ••12 Power jack13 Belt clip14 Battery compartment coverWhat’s in the box1 set for DM223; 2 sets for DM223-2Connect the baby monitorNOTESUse only the parent unit power adapter or the baby unit power adapter supplied with this product.Make sure the electrical outlets are not controlled by wall switches.The parent unit power adapter and baby unit power adapter are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.Make sure the parent unit, the baby unit and the power adapter cord are out of reach of children.••••Connect and charge the batteryParent unit display iconsConnection status displays when strong signal strength is detected between the baby unit and the parent unit. displays when moderate signal strength is detected between the baby unit and the parent unit. displays when the weak signal strength is detected between the baby unit and the parent unit. flashes when the link between the baby unit and the parent unit is lost.••••Night light auto-onOn when the night light auto-on feature is turned on. •Sound alertDisplays when the sound alert of the parent unit is turned on.Flashes when there are loud sounds detected from the baby unit and the parent unit is in mute.••Vibration alertDisplays when the vibration alert of the parent unit is turned on.Flashes when there are loud sounds detected from the baby unit.••MuteDisplays when the volume is turned off.•Battery status animates when the battery is charging. displays solid when the battery is fully charged. flashes when the battery is charged with AC adaptor, or charging failure. flashes when the battery is in low level and needs charging.No battery icon displays when there is no battery installed.•••••Power on or off the baby unitPress and hold POWER to power on the baby unit. The power light turns on.Press and hold POWER again to power off the baby unit. The power light turns off.Power on or off the parent unitPress and hold to power on the parent unit. The screen turns on.Press and hold again to power off the parent unit. The screen turns off.NOTEThe parent unit powers on automatically once it is connected to AC power or battery installed. The baby unit also powers on automatically once connected to AC power. Adjust the speaker volume for baby unitPress VOL. or VOL. on the baby unit at any time.Adjust the speaker volume for parent unitYou can adjust the speaker volume from VOLUME 1 to VOLUME 5, or turn it off. The speaker volume is preset to VOLUME 3.Press VOL. or VOL. when the parent unit is not in use.When the speaker volume is set to off, the screen displays .•••••••Using the baby monitor Night light auto-onYou can turn on or off the night light by pressing the NIGHT LIGHT button manually on the baby unit. You can also use the parent unit to set the night light on the baby unit to automatically turn on whenever sounds are detected from the baby unit.When the night light auto-on setting is set to YES, displays. The default setting is preset to NO.Press MENU when the parent unit is not in use.Press VOL. or VOL. to choose NIGHTLIGHT, then press SELECT.Press SELECT to choose AUTO ON.Press VOL. or VOL. to choose YES or NO. Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone. NOTESTo enter the night light menu of the parent unit, the baby unit must be turned on.If the night light on the baby unit is already on, the night light will go off immediately when you change the night light auto-on setting from YES to NO.If the night light on the baby unit is already on and the night light auto-on setting is YES, the night light on the baby unit will go off immediately after you press NIGHT LIGHT and the night light auto-on feature will become inactive for 5 minutes.For night light triggered by baby’s sound or turned on manually at the baby unit, it will automatically turn off after 15 minutes of silence.LanguageYou can select a language (English, French or Spanish) to be used in all screen displays. The language is preset to English.Press MENU when the parent unit is not in use.Press VOL. or VOL. to choose LANGUAGE, then press SELECT.Press VOL. or VOL. to choose ENGLISH, FRANCAIS or ESPANOL.Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone. NOTEThe language setting on each parent unit is independent.1.2.3.4.5.••••1.2.3.4.•NOTETo enter the sensitivity menu of the parent unit, the baby unit must be turned on.Sound alertSound alert feature works only when the parent unit is in mute.If you turn on the sound alert, the parent unit beeps when the baby unit detects sounds which light up four sound level indicators on the parent unit.When the sound alert of the parent unit is turned on, displays. The sound alert is preset to OFF.Press MENU when the parent unit is not in use.Press VOL. or VOL. to choose SOUND ALERT, then press SELECT.Press VOL. or VOL. to choose ON or OFF.Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone.NOTEThe sound alert setting on each parent unit is independent.Vibration alertYou can turn on the vibration alert so that the parent unit vibrates when the baby unit detects sounds which light up four sound level indicators on the parent unit.When the vibration alert of the parent unit is turned on, displays. The vibration alert is preset to OFF.Press MENU when the parent unit is not in use.Press VOL. or VOL. to choose VIBE ALERT, then press SELECT.Press VOL. or VOL. to choose ON or OFF.Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone.NOTESEach time you set the vibration alert to ON, the parent unit vibrates briefly after you press SELECT.The vibration alert setting on each parent unit is independent.•1.2.3.4.•1.2.3.4.••Congratulationson purchasing your new VTech product. Before using this product, please read Important safety instructions. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.Register online to get an additional 3-month warranty!Visit www.vtechphones.com.RegistrationRegister your product online for enhanced warranty support.Product newsLearn about the latest VTech products.Place the baby unit at least 1 meter / 3 feet away from your baby.2. Place the parent unit at least 1 meter / 3 feet away from the baby unit.NOTEIf you experience audio feedback on either the parent unit or baby unit, move the parent unit further away until there is no more audio feedback; or press VOL. on the parent unit to lower the audio feedback sound.Operating rangeThe operating range of the baby monitor is up to 300 meters (1,000 feet) outdoors or 50 meters (160 feet) indoors. The actual operating range may vary depending on the environmental conditions, and other interferences such as walls, doors, and other obstructions. 1.•Parent unit display screen messagesCHECK BATTThe battery charging performance is abnormal, the light is off and the icon flashes on the screen.LINKED The link between the parent unit and the baby unit is established.LOW BATTERYThe parent unit uses only the rechargeable battery pack and it needs to be recharged.NOT LINKEDThe link between the parent unit and the baby unit is lost continuously for over 10 seconds.PAGING All idle parent units are being paged by the baby unit.SAVED Your selection has been saved.SEARCHING The parent unit is out of range of the baby unit, or the baby unit is out of power.TALK The parent unit is talking to the baby unit.TALKBACK The other parent unit is talking to the baby unit.At least 1 meter (3 feet)jhihgicbdfaemnkjlLINKEDLINKEDHigh sensitivityLow sensitivityLevel 5Level 4Level 3Level 2Level 1At least 1 meter (3 feet)THIS SIDE UPBattery Pack / Bloc-piles :BT183342/BT283342 (2.4V 400mAh Ni-MH)WARNING / AVERTISSEMENT :DO NOT BURN OR PUNCTURE BATTERIES.NE PAS INCINÉRER OU PERCER LES PILES.Made in China / Fabriqué en chine CR0920 THIS SIDE UP / CE CÔTÉ VERS LE HAUTBattery Pack / Bloc-piles :BT183342/BT283342 (2.4V WARNING / AVERTISSEMEDO NOT BURN OR PUNCTNE PAS INCINÉRER OU PMade in China / FabriquéTHIS SIDE UP / CEfegbacd
What does this limited warranty cover?The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada.What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days.How long is the limited warranty period?The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer. What is not covered by this limited warranty?This limited warranty does not cover:Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; orProduct that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; orProduct to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; orProduct to the extent that the problem is caused by use with non-VTech accessories; orProduct whose warranty/quality stickers, product 1.2.3.4.5.To keep this product working well and looking good, follow these guidelines:Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).DO NOT expose it to direct sunlight or moisture.Avoid dropping the product or treating it roughly.Clean with a soft cloth.DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.DO NOT use cleaning spray or liquid cleaners.Make sure the baby unit and parent unit are dry before you connect them to the mains again.When you are not going to use the baby monitor for some time, remove the rechargeable battery from the parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place. •••••••The RBRC® seal on the nickel-metal battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.The RBRC® program provides a convenient alternative to placing used nickel-metal batteries into the trash or municipal waste, which may be illegal in your area.VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers participating in the RBRC® program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.RBRC® and 1 (800) 8 BATTERY® are registered trademarks of Rechargeable Battery Recycling Corporation.Frequently asked questionsThe RBRC® sealFCC and IC regulationsLimited warranty serial number plates or electronic serial numbers have been removed, altered or rendered illegible; orProduct purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); orProduct returned without a valid proof of purchase (see item 2 on the next page); orCharges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.How do you get warranty service?To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save you a service call.Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.What must you return with the Product to get warranty service?Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; andInclude a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; andProvide your name, complete and correct mailing address, and telephone number.Other limitationsThis warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you 6.7.8.1.2.3.Frequency controlCrystal controlled PLL synthesizerTransmit frequencyBaby unit: 1921.536-1928.448 MHzParent unit: 1921.536-1928.448 MHzChannels 5LCD 35 (x) x 21.2 (y) mm B&W LCDNominal effective rangeMaximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.Power requirementParent unit: 2.4 V Ni-MH batteryBaby unit power adapter:Input: 100-120V AC 150mA 60HzOutput: 6V DC 400mAParent unit power adapter:Input: 100-120V AC 150mA 60HzOutput: 6V DC 400mASpecifications are subject to change without notice.© 2015 VTech Communications, Inc.All rights reserved. 10/15. DM223_CIB_V1.0Document order number: 91-008851-010-100should not rely on any such modification.State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province.Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase.Technical specificationsThis baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy-conserving standards right out of the box.Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging.Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging.California Energy Commission battery charging testing modeMesures de sécurité importantesLorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base afin de réduire les risques d’incendie, d’électrocution et de blessures corporelles, dont ceux qui suivent:Observez toutes les instructions et mises en garde inscrites sur l’appareil.L’installation par un adulte est requise.Ce produit a été conçu pour être un dispositif d’appoint seulement. Il n’est pas le remplacement d’une supervision responsable et adéquate par un adulte et ne devrait pas être utilisé comme telle.Ce produit n’est pas conçu pour être utilisé en tant que moniteur médical.N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier de cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche.1.2.3.4.5.For cETL compliance only MISE EN GARDE: Il peut y avoir un risque d’explosion si vous utilisez le mauvais type de piles pour l’unité du parent. N’utilisez que le bloc-piles rechargeable inclus ou le bloc-piles de rechange (BT166342/BT266342). N’incinérez pas les piles. Celles-ci risqueraient d’exploser. Jetez les piles usées selon les renseignements suivant le sceau du RBRCMD.N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque d’endommager sérieusement le produit et mettre votre sécurité en péril. Adaptateur de l’unité du bébé: Entrée 100-120V CA 150 mA 60 Hz; Sortie : 6 V CC 400 mA. Adaptateur de l’unité du parent: Entrée 100-120V CA 150 mA 60 Hz; Sortie : 6 V CC 400 mA.Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs secteur ont été conçus pour être orientés correctement, soit à la verticale ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si celuici est branché dans une prise au plafond, sous une table ou dans un meuble.Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de courant doit être installée près du produit, afin d’assurer une accessibilité sécuritaire à la prise de courant.Débranchez ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon humide pour le nettoyer.Débranchez les cordons d’alimentation avant de remplacer le bloc-piles.Ne coupez pas les cordons d’alimentation pour remplacer les fiches, car ceci peut présenter un danger potentiel.Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un endroit où l’on risque d’écraser le cordon d’alimentation ou de le piétiner.Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que vous possédez à votre domicile, consultez votre marchand ou votre compagnie locale d’électricité.Ne surchargez pas les prises de courant murales ni les rallonges électriques.Ne placez pas cet appareil sur un chariot, meuble, trépied, support de montage ni table chancelants.Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de surchauffer, ne bloquez sous aucun prétexte ces ouvertures et 6.7.8.9.10.11.12.13.14.15.16.17.FCC Part 15This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face.This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B)Industry CanadaThis device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation.The term ‘’IC:‘’ before the certification/registration ••••n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur un lit, divan, tapis ou toute autre surface similaire. De même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un calorifère. De plus, ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-circuits qui peuvent dégénérer en incendies ou en risques d’électrocution. Ne renversez jamais de liquide dans ce produit.Afin de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un centre de service autorisé. L’ouverture du boîtier ou le retrait de toutes pièces que contient cet appareil, à l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de vous exposer à des points de tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite présenter des risques d’électrocution.Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.Examinez les composantes afin de vérifier si celles-ci ne sont pas endommagées.Soyez avisé de la perte de la confidentialité lorsque vous utilisez les ondes publiques. Les conversations peuvent être entendues par d’autres moniteurs de bébé, des téléphones sans fil, des scanneurs, etc.Les enfants devraient être supervisés afin de vous assurer qu’ils ne jouent pas avec l’appareil.Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné suffisamment de supervision ou d’instructions relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité.CONSERVEZ CES INSTRUCTIONS18.19.20.21.22.23.24.Mises en gardeUtilisez et entreposez le produit à une température entre 0˚ C (32˚F) et 40˚C (104˚ F).N’exposez pas cet appareil à des froids ou des chaleurs extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une source de chauffage.Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.1.2.3.Assurez-vous que le moniteur et le cordon de l’adaptateur sont toujours hors de portée des enfants, à au moins 1 mètre (3 pieds) de l’enfant ou du berceau, pour éviter tout risque de strangulation.Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec un article tel une serviette ou une couverture.D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez d’installer votre moniteur vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans fil, radios, téléphones cellulaires, interphones, moniteurs, téléphones, ordinateurs personnels, électroménagers et téléphones sans fil.Stimulateurs cardiaques implantés dans l’organismeLes simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil):L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:Avis aux détenteurs de stimulateurs cardiaquesVous devriez maintenir les dispositifs sans fil à au moins six pouces du simulateur cardiaque.Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche.L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent dispositifs sans fil à proximité de ceux-ci.Champs électromagnétiques (EMF)Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures évidences scientifiques dont nous disposons aujourd’hui.4.5.6.••When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:Follow all warnings and instructions marked on the product.Adult setup is required.This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.This product is not intended for use as a medical monitor.Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.6. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion 1.2.3.4.5.if a wrong type of battery is used for the parent unit. Use only the supplied rechargeable battery or replacement battery pack (BT166342/BT266342) for the parent unit. Do not dispose of batteries in a fire. They may explode. Dispose of used battery according to the information in The RBRC® seal.7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Baby unit power adapter: Input 100-120V AC 150mA 60Hz; Output: 6V DC 400mA; Parent unit power adapter: Input 100-120V AC 150mA 60Hz; Output: 6V DC 400mA.8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.10.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.11.Unplug the power cords before replacing batteries.12.Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.13.Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.14.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.15.Do not overload wall outlets or use an extension cord.16.Do not place this product on an unstable table, shelf, stand or other unstable surfaces.17.This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.18.Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.Important safety instructionsCautionsUse and store the product at a temperature between 32oF and 104oF.Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.Batteries should not be exposed to excessive heat such as bright sunshine or fire.Make sure the baby unit(s) and the adapter cord(s) are always out of reach of the baby, at least 3 feet away from the baby or crib, to avoid a possible strangulation hazard.Never place the baby unit(s) inside the baby’s crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket.Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.1.2.3.4.5.6.Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your question, visit our website at www.vtechphones.com or call 1 (800) 595-9511 for customer service.Why does the baby monitor not respond normally?Try the following (in the order listed) for common cure:1. Disconnect the power to the baby unit and the parent units.2. Remove the batteries in the parent units. Then, install the batteries again.3. Wait a few minutes before connecting power back to the baby units and the parent unit.4. Turn on the baby unit and the parent units.5. Wait for the parent units to synchronize with the baby unit. Allow up to one minute for this to take place.Why doesn’t the screen of the parent unit go on when I switch on the unit?Perhaps the rechargeable battery of the parent unit is empty and the parent unit is not connected to the power. Insert the appliance plug into the parent unit and put the adapter in a wall socket. Why doesn’t the POWER light of the baby unit go on when I switch on the unit?Perhaps the baby unit is not connected to the power. Connect the baby unit to the power. Why does the baby monitor produce a high-pitched noise?The units may be too close to each other. Make sure the parent unit and the baby unit are at least 1 meter/3 feet away from each other.Why does the parent unit react too quickly to other sounds?The baby unit also detects other sounds than those of your baby. Adjust the sensitivity level to a lower level or adjust the speaker volume on the parent unit.StorageGeneral product careSet defaultUse this feature to restore to the default settings. Restoring the default settings on one parent unit will also reset the shared settings for sensitivity and night light auto-on feature of the other parent unit.Press MENU when the parent unit is not in use.Press VOL. or VOL. to choose SET DEFAULT, then press SELECT.Press VOL. or VOL. to choose YES or NO.When you choose YES, press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone. -OR- When you choose NO, press SELECT to confirm your selection. The screen displays the previous menu. Talk to the baby unitYou can broadcast messages from a parent unit to the baby unit and the other parent unit. If you have two parent units, you can use both of them at the same time to talk to the baby unit. Press and hold TAL K on the side of the parent unit. The screen displays TALK when the voice connection to the baby unit is made. Speak towards the MIC on the parent unit. Your voice is broadcast to the baby unit and the other parent unit. NOTEWhen a parent unit is talking to the baby unit, it is also broadcast to the other parent unit. However, sounds from the baby unit cannot be transmitted to the parent units at the moment.Find/page the parent unitUse this feature to find misplaced parent units.Press PAGE on the baby unit. All idle parent units ring and display PAGING.To end paging, press any key on the parent unit, or press PAGE on the baby unit.NOTESPaging rings all parent units even if the speaker volume of parent unit is set to VOLUME OFF.The baby unit cannot page any parent unit that is turned off, out of range or talking to the baby unit.1.2.3.4.••1.2.••Why don’t I hear a sound/Why can’t I hear my baby cry?The volume of the parent unit may have set too low. Press VOL. to increase the volume level.You may have set a low sound sensitivity level. See Adjust the sound sensitivity of the baby unit to change the setting.Why does the parent unit beep?If the parent unit is in mute and the sound alert feature is on, there is sound detected from the baby unit.The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet). If the parent unit is powered by the provided battery, it may not have enough charge for the parent unit to perform normally. Charge the battery in the parent unit for up to 11 hours.Why can’t I establish a connection? Why is the connection lost every now and then? Why are there sound interruptions?The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet).Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible.19.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.20.You should test the sound reception every time you turn on the units or move one of the components.21.Periodically examine all components for damage.22.Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc.23.Children should be supervised to ensure that they do not play with the product.24.The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.SAVE THESE INSTRUCTIONSPrecautions for users of implanted cardiac pacemakersCardiac pacemakers (applies only to digital cordless devices):Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:Pacemaker patientsShould keep wireless devices at least six inches from the pacemaker.Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.Electromagnetic fields (EMF)This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.••number only signifies that the Industry Canada technical specifications were met.This product meets the applicable Industry Canada technical specifications.RF radiation exposure statementThe baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

Navigation menu