VTech Telecommunications 80-0585-00 Wireless Speaker User Manual

VTech Telecommunications Ltd Wireless Speaker

User Manual

Quick start guideModel: VCS850Wireless Conference SystemErisStationTMbusinessphones.vtech.comWireless speaker for VCS752 SIP Conference PhoneCongratulationson purchasing your new VTech product.For support, shopping, and everything new at VTech, visit our website at businessphones.vtech.com.The VCS850 Wireless Speaker extends the range of the VCS752 SIP Conference Phone. Register up to three VCS850 speakers to continue conversations anywhere in a large conference room.Installing the wireless speaker battery• Risk of explosion! Batteries should not be exposed to excessive heat such as bright sunlight or re.• Use only the supplied battery.• Risque d’explosion! Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.• N’utilisez que la pile incluse.1. After removing the battery door, plug the battery connector securely into the socket inside the battery compartment.2. Place the battery into the battery compartment.3. Attach the battery door until it clicks into place.Connecting power to the VCS8501. Plug one end of the AC adapter into the power jack on the bottom of the unit.2. Route the cord through the slots.3. Plug the large end of the AC adapter into a wall outlet not controlled by a switch.• After connecting power, the VCS850 LEDs should ash red and green, indicating the unit is ready for registration.• The supplied power adapter is designed for use with only the ErisStation Conference Phone with Two Wireless Mics. It is not designed to power other network devices. Do not connect the supplied power adapter to any other network devices through the supplied DC power cable or any other Cat5e ethernet cable.• The AC power cord is intended for a vertical or oor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling or cabinet outlet.®1. Microphone2. Speaker3. MUTE ALLDuring a call, press to mute or end mute all microphones in the system.4. Press to answer or end a call.5. Multipurpose LEDs (four)6. / • Press to adjust the ringer volume.• During a call, press to adjust the listening volume.7. Microphone1253467LED color and behavior VCS850 StatusGREENSteady FlashingFlashing (with red LED)Slow ashOn for 5 secs• Call active, speaker on• Incoming call• Ready for registration• Paged by base• Successfully registeredREDFlashing (with green LED)On for 5 secsSteadySlow ash• Ready for registration• Registration failed• Microphone muted• Out of range, deregisteredORANGESteadyOn for 5 secs• Reset mode• Power onPower LED• On when charging• Off when charging is complete• Flashes when battery is low
ComplianceFCC Part 15This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Changes or modications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The wireless mic may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more.This Class B digital apparatus complies with Canadian requirement CAN ICES-3 (B)/NMB-003(B)Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Industry CanadaOperation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Privacy of communications may not be ensured when using this telephone.The term ‘’IC:‘’ before the certication/registration number only signies that the Industry Canada technical specications were met.This product meets the applicable Innovation, Science and Economic Development Canada technical specications.SpecicationsFrequency control Crystal controlled PLL synthesizerTransmit frequency 1921.536–1928.448 MHzChannels 5Nominal effective rangeMaximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.Power requirements Ni-MH Battery Pack; 7.2V; 2100mAH rechargeable batteryBase unit adapter: Input: 100–240V AC 50/60Hz Output: 12V DC @ 1.0ARegister the wireless speakerYou must register the wireless speaker using the menus on the VCS752 SIP Conference Phone.1. On the VCS752 SIP Conference Phone, press MENU.2. On the Main Menu, highlight User settings and then press SELECT.3. On the User settings menu, highlight Wireless speaker. 4. With Register highlighted, press SELECT. The screen displays Registering... and then Registration succeeded. The base plays a conrmation tone. The registered speaker LEDs stop ashing red and green. The LEDs turn green briey and then turn off.5. Repeat steps 1 to 4 for any additional wireless speakers. • If a microphone fails to register, the base unit will display Registration failed. • To cancel registration, press Cancel.For complete operating instructions, see the VCS850 User Guide, available from our website at businessphones.vtech.com.Specications are subject to change without notice.© 2016 for VTech Communications, Inc.All rights reserved. 08/16. VCS850_QSG_V1

Navigation menu