VTech Telecommunications 80-0619-00 Full Color Video Monitor with Wide-angle Lens - Baby Unit User Manual manual

Download:
Mirror Download [FCC.gov]
Document ID	3718021
Application ID	aLto5L+flkESKnk1OYnsoQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	123.2kB (1540028 bits)
Date Submitted	2018-01-18 00:00:00
Date Available	2018-01-18 00:00:00
Creation Date	2018-01-08 23:38:52
Producing Software	GPL Ghostscript 9.07
Document Lastmod	2018-01-08 23:38:52
Document Title	manual.pdf
Document Creator	PDFCreator Version 1.7.1
Document Author:	stanleyl

Congratulations
VM4261
VM4261-2
on purchasing your new VTech product. Before
using this product, please read Important
safety instructions.
Full Color Video Monitor
with Wide-angle Lens
This manual has all the feature operations
and troubleshooting necessary to install and
operate your new VTech product. Please
review this manual thoroughly to ensure proper
installation and operation of this innovative and
feature rich VTech product.
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
BC
For support, shopping, and everything new at
VTech, visit our website at
www.vtechphones.com.
Install the battery
The parent unit runs on rechargeable battery
or AC power. To continuously monitor your
baby, make sure you use both battery and
AC power at the same time. With the battery
alone, the parent unit can cordlessly run for a
short time only.
NOTES
• Use only the battery supplied with this product.
• If the parent unit will not be used for a long time,
disconnect and remove the battery to prevent
possible leakage.
Install the battery as shown below.
Connect and charge the
battery
NOTES
• Use only the power adapters supplied with this
product.
• Make sure the electrical outlets are not controlled
by wall switches.
• The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if
they are plugged into a ceiling, under-the-table or
cabinet outlet.
• Make sure the parent unit, the baby unit and the
power adapter cords are out of reach of children.
Connect the baby monitor
What’s in the box
o deción
Riesg
ngula
estra
ion
gulat
rd
Stran
Haza
feet
of children.
three not
of reach
Do
out
at least
not
cord to be all times.
Do
at
this
child cord.
Keep cord needs
the
The from extension
awaywith an tag.
this
use
remove
e ent
Risqu
nglem
d’étra
Le
trois
enfants.
des au moinstemps.
à
pas
en toutretirez
ce cordon
se trouver
et ce, Ne
Éloignez doit
enfant rallonge.
cordond’un
de
pas .
pieds
N’utilisez
étiquette
cette
alcance
de la por
fuera estar
cable debela alcance
use
a esteEste cable de No lo quite
fuera o.
No
Manteng
niños. pies moment ica.
tres
de los
inalámbr
en todo
lo menos
niño
del una extensión
con etiqueta.
esta
NOTES
Charge the parent unit battery
When you have connected the parent unit
and installed its battery for the first time or
after power outage, the parent unit powers on
automatically. The battery icon indicates the
battery status (see the following table).
• The parent unit battery is fully charged after
3 hours of continuous charging.
• It takes longer to charge the battery when the
•
parent unit is turned on. To shorten the charging
time, turn the parent unit off while charging.
The standby time varies depending on the
volume level you set, your actual use and the
age of the battery.
Battery
indicators
Battery
status
Action
The battery
icon is off
and
displays.
No battery
is installed
but operates
using AC
power, or the
battery has
been installed
incorrectly.
Install the
parent unit
battery.
Charge
without
interruption
(at least 30
minutes).
The screen
displays
Battery low
at Parent
Unit and
The
light
flashes.
The battery
has very little
charge and
may be used
for only a
short time.
Charge
without
interruption
(about 30
minutes).
The battery
icon
becomes
solid
The battery is
fully charged.
To keep
the battery
charged,
connect it to
AC power
when not in
use.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Strangulation
Hazard
Risque
d’étranglement
Riesgo de
estrangulación
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
THIS SIDE UP
NOTES
o de ión
Riesggulac
estran
ion
gulat
rd
Stran
Haza
feet
of children.
three not
of reach
Do
out
at least
not
cord to be all times.
Do
at
this
child cord.
Keep cord needs
the
The from extension
awaywith an tag.
this
use
remove
e ent
Risqu
nglem
d’étra
Le
trois
enfants.
des au moinstemps.
à
pas
en toutretirez
ce cordon
se trouver
et ce, Ne
Éloignez doit
enfant rallonge.
cordond’un
de
pas
pieds
N’utilisez
étiquette.
cette
alcance
de la por
fuera estar
cable debe alcance
este cable de la No lo usequite
Este fuera
No
Mantenga
niños. pies momento ca.
tres
de los
inalámbri
en todo
lo menos
niño
del una extensión
con etiqueta.
esta
Riesgo de
estrangulación
Risque
d’étranglement
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Strangulation
Hazard
Antenna
Temperature sensor
ON/OFF switch
• Slide to turn on or off the baby unit.
ON/OFF LED light
• On when the baby unit is turned on.
• Flashes when the baby unit is not
being viewed; or when the link to the
parent unit is lost.
Light sensor
Camera
Infrared LEDs
Microphone
Speaker
10
Power jack
11
Threaded socket
12
PAIR
• Your baby units and parent unit
provided are already paired.
Parent unit overview
Microphone
Zoom
• While viewing image, press to zoom
in or out.
10
11
12
18
17
19
15
VIEW
• Press to view the image of the next
baby unit in Single-CAM or Patrol
mode.
• For VM4261-2 only
LCD ON/OFF
• Press and hold to turn off the parent
unit screen.
Power jack
/ BACK
• While in a menu, press to return to
the main menu or idle screen.
• While in Single-CAM or Patrol
mode, press and hold to move the
baby unit camera leftward.
• While in Split-view mode, press to
move the selection box leftward.
16
Antenna
18
Speaker
On/off
• Press and hold to power on.
• Press and hold to power off.
19
Stand
10
MENU/SELECT
• Press to enter the menu.
• While in a menu, press to choose
an item, or save a setting.
11
• While in a menu, press to scroll up.
• While in Single-CAM or Patrol
mode, press and hold to move the
baby unit camera upward.
• While in Split-view mode, press to
move the selection box upward.
12
16
LCD display
+/VOL/• Press to adjust the speaker volume.
14
15
14
13
• While in a menu, press to choose
an item.
• While in Single-CAM or Patrol
mode, press and hold to move the
baby unit camera rightward.
• While in Split-view mode, press to
move the selection box rightward.
TALK
• While viewing image, press and hold
to talk to the selected baby unit.
Parent unit status icons
13
LED lights
• Indicate the different statuses of the
parent unit. For details, refer to
Parent unit lights.
• While in a menu, press to scroll down.
• While in Single-CAM or Patrol
mode, press and hold to move the
baby unit camera downward.
• While in Split-view mode, press to
move the selection box downward.
17
Connection status
•
displays when strong signal
strength is detected between the
baby unit and the parent unit.
•
or displays when moderate
or low signal strength is detected
between the baby unit and the
parent unit.
• displays when the link between the
baby unit and the parent unit is lost.
Lullaby
• Displays when the baby unit being
viewed is playing lullabies or
soothing sounds.
or Current view status
or • Displays the baby unit number of
the baby unit that is being viewed
or
when in Single-CAM and Patrol
mode.
• Displays the baby unit number of
the selected baby unit when in
Split-view mode.
PATROL
• Press to turn on or off the Patrol
mode.
• For VM4261-2 only
SPLIT
• Press to turn on or off the
Split-view mode.
• For VM4261-2 only
Patrol mode
• Displays when the parent unit is in
Patrol mode.
• For VM4261-2 only
Parent unit lights
LINK
Split-view mode
• Displays when the parent unit is in
Split-view mode.
• For VM4261-2 only
• On when the parent unit is linked
to the baby unit.
• Flashes when the link to the baby
unit being viewed in Single-CAM
or Patrol mode is lost; or when the
link to at least one baby unit being
viewed in Split-view mode is lost.
Night vision
• Displays when the baby unit being
viewed has activated the night
vision feature.
• On when the parent unit is
connected to AC power, or the
battery is charging.
• Flashes when the parent unit
battery is low and needs charging.
• Off when the parent unit is
disconnected from AC power.
Zoom
• Displays when the current image
on the parent unit has zoomed in.
Temperature alert tone
• Displays when the temperature
alert tone is on.
It turns on:
• When the speaker volume of the
parent unit is turned off; or
• When the parent unit is in Split-
view mode; or
• When the parent unit is talking to
the baby unit.
TALK • On when the parent unit is talking
to the baby unit.
F or
Real-time temperature
• Displays the real-time temperature
detected by the baby unit in
Fahrenheit (oF) or Celsius (oC)
(e.g. 57 oF or 14 oC).
You may test the baby monitor before initial
use, and at regular times thereafter.
Mute alert
• Displays when the parent unit
speaker volume is set to off.
• Displays when Split-view mode is
turned on.
9-level sound indicator
(1 to 3 bars) indicates low sound
•
level detected by the baby unit.
•
(4 to 6 bars) indicates
moderate sound level detected by
the baby unit.
(7 to 9 bars) indicates high
•
sound level detected by the baby
unit (e.g. baby crying loudly).
Speaker volume
• Displays the parent unit speaker
volume level while adjusting.
Battery status
•
animates
when the battery is charging.
displays solid when the battery
•
is fully charged.
•
displays when the battery is
low and needs charging.
AC power without battery
• Displays when the parent unit is
connected to AC power without
the battery.
Parent unit main menu icons
Alert Tone
You can set the parent unit to beep
when
• the parent unit operates in low
battery condition;
• the link between the parent unit
and the baby unit is lost; or
• the baby unit detects sounds
while in Split-view mode.
Language
You can select a language
(English, French or Spanish) to be
used in all screen displays.
LCD
You can change the brightness of
the parent unit screen, or turn on
the Dim Mode to save power.
NOTE
• To avoid interference from other electronic
devices, place your baby monitor far away from
devices such as wireless routers, microwaves,
cell phones and computers.
1. Place the baby units more than 3 feet
(1 meter) away from your baby.
CAUTION
• For hearing protection, make sure the
parent unit is more than 3 feet (1 meter)
away from both baby units. If you hear any
high-pitched noise, move the parent unit
further until the noise stops. You can also
press VOL/- on the parent unit to lower or
mute the noise.
> 3ft (1m)
Rename
You can choose a specific name
for the baby unit from a pre-defined
name list.
VOX Sensitivity
With this feature, you can choose
to hear sounds from the baby unit
all the time, or to hear sounds that
exceed a certain level. You can
use the parent unit to adjust the
microphone sensitivity of your baby
unit. The higher the sensitivity level,
the more sensitive the baby unit is
in detecting sounds for transmitting
to the parent unit.
Sound-activated Screen
When the baby unit being viewed
detects no sound, the parent
unit screen stays off to save
power. Once a sound is detected,
the parent unit screen turns on
automatically. It will then turn
off again after 50 seconds of no
sound detection.
Temperature
You can turn on the temperature
alert tone so that the parent
unit beeps whenever the room
temperature detected by the baby
unit falls outside of the desired
temperature range.
You can choose to display the
temperature in Fahrenheit (oF) or
Celsius (oC), or set the maximum/
minimum temperature limit for alerts.
Lullaby on CAM
You can choose a lullaby or
soothing sound to comfort your
baby.
Volume on CAM
You can adjust the volume of baby
units which determines the lullaby
volume and talkback volume
transmitted from parent unit.
Vibration
You can turn on the vibration alert
so that the parent unit vibrates
when it receives Low battery
tone, No link alert, Sound alert
in split-view or Temperature
alert tone after turning on the
respective alert tones.
Operating range
The operating range of the baby monitor is
up to 1,000 feet (300 meters) outdoors or
160 feet (50 meters) indoors. The actual
operating range may vary depending on
the environmental conditions and other
interferences such as walls, doors and other
obstructions.
Overview
Baby unit overview
Install the lens (optional)
The wide-angle lens (VM101) provided allows
you to view more of your baby’s room from the
parent unit screen. Install the wide-angle lens
onto the baby unit camera as shown below.
63ē
63ē
> 3ft (1m)
2. Place the parent unit more than 3 feet
(1 meter) away from the baby units.
Remove the lens
1. Make sure your baby units and parent unit
are on.
2. The parent unit displays images from the
baby unit.
• Speak towards the microphone of the
baby unit. You will hear the sound at the
parent unit.
3. If you have two baby units, press VIEW
at the right side of your parent unit. The
screen switches to other baby unit. Then,
repeat step 2.
63ē
> 3ft (1m)
10
63ē
< 3ft (1m)
NOTES
TIP
1 set for both VM4261 and VM4261-2
Test your baby monitor
• Keep the baby unit out of the reach of your baby.
Never place or mount the baby unit inside the
baby’s crib or playpen.
CAUTION
•
The default volume of your parent unit is level
4, and the maximum volume is level 7. If you
experience high-pitched screeching noise from
your baby monitor while positioning:
- Make sure your baby units and parent unit are
more than 3 feet (1 meter) apart, OR
- Turn down the volume of your parent unit.
Parent unit warning icons and
messages
No link to
CAM #
The selected baby unit is
out of range or is turned
off.
The battery level of the
Battery low at parent unit is very low and
Parent Unit
needs to be recharged.
Battery empty.
Powering off ...
The battery is empty and
needs to be recharged.
The sound level exceeds
Sound
the threshold at CAM # in
detected at CAM # Split-view mode.
Temperature
too high at CAM #
or
Temperature
too low at CAM #
The temperature detected
by the baby unit is higher/
lower than the desired
temperature alert range.
Auto Timer of
lullaby is reset
The auto timer for playing
lullaby is reset.
# represents the baby unit number.
Using the baby monitor
Power on or off the baby unit
• Slide the ON/OFF switch to the left to turn
on the baby unit. The ON/OFF LED light
turns on.
• Slide the ON/OFF switch to the right to turn
off the baby unit. The ON/OFF LED light
turns off.
Power on or off the parent unit
• Press and hold to turn on the parent unit.
The screen turns on.
• Press and hold to turn off the parent unit.
The screen turns off.
12
• When the lens is not in use, cover both sides of
the lens with the lens covers provided to avoid
scratches.
wide-angle lens (VM101) onto your baby unit if
necessary.
Turn on or off the parent unit
screen
You can turn on or off the parent unit screen
without powering off the parent unit. You can
still hear sound from the baby unit.
• Press and hold LCD ON/OFF on the parent
unit to turn off the screen.
• Press any key on the parent unit to turn on
the screen again.
Adjust the speaker volume
For parent unit:
• Press +/VOL/- on the parent unit at any
time when viewing images.
NOTE
• When the parent unit speaker volume is set to
zero,
appears on the screen and the
light
turns on.
For baby unit:
The parent unit is
searching for baby units.
11
NOTES
• You can purchase and install an extra new
• Increase the speaker volume of the parent unit if
you cannot hear the sounds transmitted from the
baby units.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
User’s manual
Replace the battery
To replace the battery, pull out the battery
compartment cover, and then lift up the
battery. Follow the steps above to install the
new battery.
NOTES
• This baby monitor is intended as an aid. It is not a
substitute for proper adult supervision, and should
not be used as such.
• When the parent unit displays and then
No link to CAM # (# represents the baby unit
number), and the LINK LED light flashes, move
the parent unit closer to the baby units (observe
the minimum distance of 3 feet/ 1 meter). You can
also check if the baby monitor is connected to a
live power socket and switched on.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
1 set for VM4261
2 sets for VM4261-2
CAUTION
NOTES
• Press down on the battery compartment cover to
pull it out.
• Make sure the label THIS SIDE UP is facing up
while inserting the battery.
Positioning the baby monitor
Before use
The baby unit speaker volume can be
adjusted in the parent unit. The baby unit
speaker volume determines the lullaby volume
and talkback volume transmitted from parent
unit. Level 1 is the softest while Level 5 is the
loudest.
1. Press MENU when the parent unit is idle.
2. Press or to choose Volume on CAM,
then press SELECT.
3. Press or to choose the desired volume
level, then press SELECT to confirm your
selection.
Turn on or off the dim mode
In Single-CAM or Patrol mode:
The dim mode is preset to on to help you save
the parent unit power. Your parent unit display
will dim automatically after 10 minutes of
inactivity, in which there is neither key pressed
nor alert received from the baby unit.
• Press VIEW to view the next baby unit.
1. Press MENU when the parent unit is idle.
2. Press or to choose LCD, then press
SELECT.
3. Press or to choose Dim Mode, then
press SELECT.
4. Press or to choose On or Off, then
press SELECT to confirm your selection.
NOTE
• While the screen is dimmed, any keypress or
alert message will trigger the screen to return to
the preset brightness level. After 10 minutes of
inactivity, it will be dimmed again.
You can change the brightness of the parent
unit screen from Level 1 to Level 5. The LCD
brightness is preset to Level 3.
1. Press MENU when the parent unit is idle.
You can remotely pan and tilt your baby unit
camera or zoom in while viewing images from
the baby unit in Single-CAM and Patrol mode.
•
•
•
Press and hold , , or to tilt the
baby unit camera downward, upward,
leftward or rightward.
Press to zoom in. Press again to zoom out.
Press and hold , , or to move
the zoomed image downward, upward,
leftward or rightward.
Monitoring mode
Every time the parent unit is turned on, it
displays a baby unit in Single-CAM mode. If
there are two baby units in your system, you
can also monitor your baby in Patrol or Splitview mode.
Single-CAM
The screen displays a
single baby unit in full
screen.
3. Press SELECT again to choose
Brightness.
Patrol
4. Press or to choose the desired level of
brightness, then press SELECT to confirm
your selection.
A single cam view that
transits to a different baby
unit every 10 seconds.
Split-view
The screen displays all
baby units.
2. Press or
SELECT.
to choose LCD, then press
• Press PATROL to switch to Patrol mode
if you are in Single-CAM mode, and vice
versa.
Pan, tilt, zoom
* For VM4261-2 only
Adjust LCD brightness
Press VIEW
10s
• Press SPLIT to enter the Split-view mode.
In Split-view mode:
• Press , , or to select a baby unit.
• Press or VIEW key to view the selected
baby unit temporarily in Single-CAM mode.
It returns to Split-view mode after 10
seconds.
• Press PATROL to enter Patrol mode.
• Press SPLIT to return to the mode (SingleCAM or Patrol) used before entering Splitview mode.
NOTES
• The parent unit is muted while in Split-view
mode.
5. When the desired lullaby is selected, press
or to choose Play, then press SELECT.
Adjust the sound sensitivity of the
baby unit
To play soothing sound using the parent
unit:
You can choose to hear sounds from the baby
unit all the time, or to hear sounds that exceed
a certain level. You can use the parent unit to
adjust the microphone sensitivity of your baby
units from Lowest to Highest. The higher the
sensitivity level, the more sensitive the baby
unit is in detecting sounds for transmitting to
the parent unit. The VOX sound sensitivity
level is preset to Highest.
1. Press MENU when the parent unit is idle.
2. Press or to choose Lullaby on CAM,
then press SELECT.
3. Press or to choose Play Soothing
Sounds, then press SELECT.
4. Press or to choose a soothing sound,
then press SELECT.
5. Press or
SELECT.
to choose Play, then press
Sensitivity
Level
Highest VOX sensitivity
High
sensitivity level
NOTES
Talk
You can use the TALK function of the parent
unit to comfort your baby in Single-CAM and
Patrol mode.
1. Press and hold TALK on the parent unit.
The TALK light turns on.
• Lullaby playback control with the parent unit menu is
available in Single-CAM and Patrol mode only.
Highest
• The lullaby playback on the baby unit will be
paused when receiving talkback from the parent
unit.
To stop playing lullaby or soothing sound:
2. Speak towards the microphone on the
parent unit. Your voice is broadcast to the
baby unit.
1. Press MENU when the parent unit is idle.
3. Release the TALK key to stop the
broadcast. The TALK light goes off.
3. Press or
SELECT.
High
Medium
NOTES
• The parent unit speaker is muted during voice
broadcast. Sound transmission from the baby unit
resumes after TALK is released.
Lullaby
The baby monitor has five lullabies and four
soothing sounds for you to comfort your baby.
You can play the lullabies or soothing sounds
on the baby unit using the parent unit.
To play lullaby using the parent unit:
1. Press MENU when the parent unit is idle.
2. Press or to choose Lullaby on CAM,
then press SELECT.
3. Press or to choose Play Melodies,
then press SELECT.
4. Press or to choose a lullaby, or choose
Play All, then press SELECT.
To set auto timer for lullaby:
While the baby unit is playing lullaby or
soothing sound, the auto timer feature helps
you automatically stop the lullaby or soothing
sound after playing for 15/30/45/60 minutes.
You can set auto timer for lullaby with the
parent unit.
2. Press or to choose Lullaby on CAM,
then press SELECT.
4. Press or to choose the desired
lullabies duration, then press SELECT.
After 15/30/45/60 minutes, the lullaby or
soothing sound will stop automatically.
SAVE THESE INSTRUCTIONS
High VOX sensitivity level
The parent unit speaker
turns on for soft babbling
and louder sounds from your
baby. It remains quiet when
your baby sleeps soundly.
Lowest
Medium VOX sensitivity
level
The parent unit speaker
turns on for loud babbling
and louder sounds from
your baby. It remains quiet
when your baby makes soft
sounds.
Low VOX sensitivity level
The parent unit speaker
turns on for crying and
louder sounds from your
baby. It remains quiet when
your baby makes soft
sounds.
Lowest VOX sensitivity
level
The parent unit speaker
turns on for loud crying or
screeching sounds from
your baby. It remains quiet
Low
when your baby makes soft
sensitivity sounds.
1. Press MENU when the parent unit is idle.
2. Press or to choose VOX Sensitivity,
then press SELECT.
• If you have two baby units, the system
prompts you to choose the desired baby
unit or both baby units, press or to
choose ALL CAM or CAM #, then press
SELECT.
• If Play All is selected, the lullabies will
be played one after the other, until all
lullabies are played.
cabinet outlet.
9. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be
easily accessible.
10. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
11. Unplug the power cords before replacing
batteries.
12. Do not cut off the power adapters to replace
them with other plugs, as this causes a
hazardous situation.
13. Do not allow anything to rest on the power cords.
Do not install this product where the cords may
be walked on or crimped.
14. This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply in your home, consult your dealer or local
power company.
15. Do not overload wall outlets or use an extension
cord.
16. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
17. This product should not be placed in any area
where proper ventilation is not provided. Slots
and openings in the back or bottom of this
product are provided for ventilation. To protect
them from overheating, these openings must
not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or
heat register.
18. Never push objects of any kind into this product
through the slots because they may touch
dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the
product.
19. To reduce the risk of electric shock, do not
disassemble this product, but take it to an
authorized service facility. Opening or removing
parts of the product other than specified
access doors may expose you to dangerous
voltages or other risks. Incorrect reassembling
can cause electric shock when the product is
subsequently used.
20. You should test the sound reception every
time you turn on the units or move one of the
components.
21. Periodically examine all components for
damage.
22. Be aware of possible loss of privacy while using
public airwaves. Conversations may be picked
up by other nursery monitors, cordless phones,
scanners, etc.
23. Children should be supervised to ensure that
they do not play with the product.
24. The product is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
Low
1. Press MENU when the parent unit is idle.
3. Press or to choose Auto Timer, then
press SELECT.
The parent unit speaker is
constantly on, and you will
hear all sounds (including
background noises) from
your baby’s room.
Cautions
1. Use and store the product at a temperature
between 32oF and 104oF.
2. Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to
a heating source.
3. Batteries should not be exposed to excessive
heat such as bright sunshine or fire.
4.
Warning—Strangulation Hazard—
Children have STRANGLED in cords. Keep
this cord out of the reach of children (more
than 3 ft away). Do not remove this tag.
5. Never place the baby unit(s) inside the baby’s crib
or playpen. Never cover the baby unit(s) or parent
unit with anything such as a towel or a blanket.
6. Other electronic products may cause
interference with your baby monitor. Try
installing your baby monitor as far away
from these electronic devices as possible:
wireless routers, radios, cellular telephones,
intercoms, room monitors, televisions,
personal computers, kitchen appliances and
cordless telephones.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital cordless
devices):
Wireless Technology Research, LLC (WTR), an
independent research entity, led a multidisciplinary
evaluation of the interference between portable
wireless devices and implanted cardiac
pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches
from the pacemaker.
• Should NOT place wireless devices directly over
the pacemaker, such as in a breast pocket, when
it is turned ON.
WTR’s evaluation did not identify any risk to
bystanders with pacemakers from other persons
using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this
user’s manual, the product is safe to be used based
on scientific evidence available today.
TIP
• You can adjust the baby unit placement to
improve the sound detection.
Turn on or off the sound
activation
When sound activation is on, as long as no
sound is detected within 50 seconds, the
parent unit screen will turn off automatically to
save power.
When your baby unit detects a sound, which
exceeds the selected sensitivity level, the sound
activation triggers the parent unit screen to turn
on automatically. When no sound is detected
within 50 seconds, the screen will be off again.
1. Press MENU when the parent unit is idle.
2. Press or to choose Sound-activated
Screen, then press SELECT .
3. Press or to choose On or Off, then
press SELECT to confirm your selection.
2. Press or to choose Alert Tone, then
press SELECT.
3. Press or to choose No Link Alert, then
press SELECT.
4. Press or to choose On or Off, then
press SELECT to confirm your selection.
Sound alert in split-view
You can turn on the sound alert feature so
that, while in Split-view mode, the parent unit
beeps and displays Sound detected at CAM #
whenever the baby unit detects sounds.
1. Press MENU when the parent unit is idle.
2. Press or to choose Alert Tone, then
press SELECT to select.
3. Press or to choose Sound alert in
split-view, then press SELECT.
4. Press or to choose On or Off, then
press SELECT to confirm your selection.
NOTES
• The sound alert feature is only available in
Split-view mode.
NOTES
2. Press or to choose Lullaby on CAM,
then press SELECT.
to choose Stop, then press
Description
3. Press or to choose the desired
sensitivity level, then press SELECT to
confirm your selection.
The RBRC® seal
The RBRC® seal on the lithium-ion battery indicates
that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and
recycle these batteries at the end of their useful
lives, when taken out of service within the United
States and Canada.
The RBRC® program provides a convenient
alternative to placing used lithium-ion batteries into
the trash or municipal waste, which may be illegal in
your area.
VTech’s participation in RBRC® makes it easy for
you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorized
VTech product service centers. Please call
1 (800) 8 BATTERY® for information on lithium-ion
battery recycling and disposal bans/restrictions in
your area. VTech’s involvement in this program is
part of its commitment to protecting our environment
and conserving natural resources.
RBRC® and 1 (800) 8 BATTERY®
are registered trademarks of the
Rechargeable Battery Recycling
Corporation.
FCC and IC regulations
FCC Part 15
This equipment has been tested and found to
comply with the requirements for a Class B digital
device under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are
intended to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
WARNING: Changes or modifications to this
equipment not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
• Sound activation is available in Single-CAM and
Patrol mode only.
• If the sound sensitivity is set to Highest, or
lullaby is playing, the parent unit screen may
remain on continuously even though sound
activation is on. This depends on whether the
baby unit detects any sounds.
Set alert tone
Low battery tone
You can set the parent unit to beep when the
parent unit operates in low battery condition.
1. Press MENU when the parent unit is idle.
2. Press or to choose Alert Tone, then
press SELECT.
3. Press SELECT again to choose
Low Battery Tone.
4. Press or to choose On or Off, then
press SELECT to confirm your selection.
No link alert
You can set the parent unit to beep when the
link between the parent unit and the baby unit
is lost.
Monitor the temperature
Your baby unit monitors the temperature of
your baby’s room with its built-in temperature
sensor. If the detected temperature is outside
of the preset temperature range, the parent unit
will display alert message.
Set temperature range
You can set the desired room temperature
alert range. The minimum temperature can be
set between 52 oF (11 oC) and 69 oF (20 oC).
The maximum temperature can be set
between 70 oF (21 oC) and 86 oF (30 oC).
1. Press MENU when the parent unit is idle.
2. Press or to choose Temperature, then
press SELECT.
3. Press or to choose Minimum or
Maximum, then press SELECT.
• If you have more than one baby unit,
the system prompts you to choose the
desired baby unit or all baby units, press
or to choose ALL CAM or CAM #,
then press SELECT.
4. Press or to choose the desired
minimum or maximum temperature, then
press SELECT to confirm your selection.
Set the language
Mount the baby unit (optional)
You can select a language (English, French or
Spanish) to be used in all screen displays.
Temperature alert tone
You can turn on the temperature alert tone so
that the parent unit will emit an alert tone if the
detected temperature is out of range.
1. Press MENU when the parent unit is idle.
2. Press or to choose Language, then
press SELECT.
3. Press or to choose English, Français
or Español, then press SELECT to confirm
your selection.
Your baby monitor comes ready for tabletop
use. You can also choose to mount your baby
monitor on the wall. See Mount the baby unit
(optional) in the Quick Start Guide for the wall
mounting instructions.
1. Press MENU when the parent unit is idle.
2. Press or to choose Temperature, then
press SELECT.
3. Press or to choose Alert Tone, then
press SELECT.
• If you have more than one baby unit,
the system prompts you to choose the
desired baby unit or all baby units, press
or to choose ALL CAM or CAM #,
then press SELECT.
4. Press or to choose On or Off, then
press SELECT to confirm your selection.
Temperature format
You can choose to display the temperature in
Fahrenheit (oF) or Celsius (oC).
1. Press MENU when the parent unit is idle.
2. Press or to choose Temperature, then
press SELECT.
3. Press or to choose Format, then press
SELECT.
4. Press or to choose oF or oC, then press
SELECT to confirm your selection.
Turn on or off the vibration
You can turn on the vibration feature so that
the parent unit vibrates when it receives any
of No link alert, Sound alert in split-view or
Temperature alert tone after turning on the
respective alert tones.
1. Press MENU when the parent unit is idle.
2. Press or to choose Vibration, then
press SELECT .
3. Press
or
to choose On or Off.
Industry Canada
This device complies with Industry Canada licenceexempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference,
including interference that may cause undesired
operation.
The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
This product meets the applicable Industry Canada
technical specifications.
RF radiation exposure statement
The baby unit complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The baby unit should be installed and
operated with a minimum distance of 8 in (20 cm)
between the baby unit and all persons’ body. Use of
other accessories may not ensure compliance with
FCC RF exposure guidelines. This transmitter must
not be co-located or operating in conjunction with
any other antenna or transmitter. This equipment
complies also with Industry Canada RSS-102 with
respect to Canada’s Health Code 6 for Exposure of
Humans to RF Fields.
California Energy Commission
battery charging testing mode
This baby monitor meets the California Energy
Commission (CEC) regulations for energy
consumption. Your baby monitor is set up to comply
with the energy-conserving standards right out of the
box.
Follow the instructions to install and charge the
battery. The CEC battery charging testing mode is
activated while charging.
Even if the parent unit is paired to baby units, the
CEC battery charging testing mode is activated
while it is powered off and charging.
For C-UL compliance only
Mesures de sécurité importantes
Lorsque vous utilisez votre appareil, vous devriez
toujours suivre certaines mesures de précaution
de base afin de réduire les risques d’incendie,
d’électrocution et de blessures corporelles, dont
ceux qui suivent :
1. Observez toutes les instructions et mises en
garde inscrites sur l’appareil.
2. L’installation par un adulte est requise.
3. Ce produit a été conçu pour être un dispositif
d’appoint seulement. Il n’est pas le remplacement
d’une supervision responsable et adéquate par
un adulte et ne devrait pas être utilisé comme
telle.
4. Ce produit n’est pas conçu pour être utilisé en
tant que moniteur médical.
5. N’utilisez pas cet appareil près de l’eau ni de
toute autre source d’humidité, par exemple, près
d’une baignoire, cuve à lessive, évier de cuisine,
dans un sous-sol humide ni près d’une piscine,
dans un soussol humide ou une douche.
6. MISE EN GARDE: Il peut y avoir un risque
d’explosion si vous utilisez le mauvais type de
piles pour l’unité du parent. N’utilisez que le
bloc-piles rechargeable inclus ou le bloc-piles de
rechange (BT198555/BT298555). N’incinérez pas
les piles. Celles-ci risqueraient d’exploser. Jetez
les piles usées selon les renseignements suivant
le sceau du RBRC®.
7. N’utilisez que les adaptateurs inclus avec ce
produit. L’utilisation d’un adaptateur dont la
polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre
votre sécurité en péril.
Adaptateur de l’unité du bébé :
Sortie : 5V CC 800mA
Adaptateur de l’unité du parent :
Sortie : 5V CC 1A
8. Lorsqu’ils sont branchés dans une prise de
courant, les adaptateurs secteur ont été conçus
pour être orientés correctement, soit à la
verticale ou au plancher. Les broches n’ont pas
été conçues pour supporter le poids du bloc
d’alimentation et le maintenir en place si celuici
est branché dans une prise au plafond, sous une
table ou dans un meuble.
9. Pour les PRODUITS À BRANCHER À UNE
PRISE DE COURANT, la prise de courant doit
être installée près du produit, afin d’assurer une
accessibilité sécuritaire à la prise de courant.
10. Débranchez ce produit de la prise de courant
avant de procéder au nettoyage. N’utilisez pas de
nettoyants en aérosols. Utilisez un chiffon humide
pour le nettoyer.
11. Débranchez les cordons d’alimentation avant de
remplacer le bloc-piles.
12. Ne coupez pas les cordons d’alimentation pour
remplacer les fiches, car ceci peut présenter un
danger potentiel.
You can rename each baby unit. Once the
baby unit is renamed, its new name together
with the baby unit number will appear in the
sub-menu of below options:
•
VOX Sensitivity
•
Temperature
•
Rename
1. Press MENU when the parent unit is idle.
2. Press or to choose Rename, then press
SELECT.
3. Press or to choose the desired baby
unit, then press SELECT.
4. Press or to choose the desired name
for the baby unit, then press SELECT to
confirm your selection.
NOTES
• If the vibration feature is turned on, the parent
unit may vibrate as it receives sound broadcast
from the baby unit.
13. Ne laissez aucun objet reposer ni appuyer sur
le cordon d’alimentation. N’installez pas cet
appareil dans un endroit où l’on risque d’écraser
le cordon d’alimentation ou de le piétiner.
14. Ne faites fonctionner cet appareil qu’avec le
type d’alimentation indiqué sur l’étiquette. Si
vous ne connaissez pas le type d’alimentation
que vous possédez à votre domicile, consultez
votre marchand ou votre compagnie locale
d’électricité.
15. Ne surchargez pas les prises de courant
murales ni les rallonges électriques.
16. Ne placez pas cet appareil sur un chariot,
meuble, trépied, support de montage ni table
chancelants.
17. Les trous et ouvertures du boîtier, situés à
l’arrière de l’appareil ou sous celui-ci, servent à
aérer l’appareil. Pour l’empêcher de surchauffer,
ne bloquez sous aucun prétexte ces ouvertures
et n’empêchez pas l’aération adéquate de
l’appareil en le plaçant sur un lit, divan, tapis ou
toute autre surface similaire. De même, ne le
positionnez pas à proximité ni au-dessus d’une
source de chaleur ou d’un calorifère. De plus,
ne placez pas l’appareil dans un endroit avant
de vous assurer qu’il y ait une bonne circulation
d’air.
18. N’enfoncez jamais d’objets à travers les
ouvertures de cet appareil, car ils pourraient
entrer en contact avec des points de tension
dangereux ou causer des courts-circuits qui
peuvent dégénérer en incendies ou en risques
d’électrocution. Ne renversez jamais de liquide
dans ce produit.
19. Afin de réduire les risques d’électrocution, ne
démontez pas cet appareil, mais apportez-le
dans un centre de service autorisé. L’ouverture
du boîtier ou le retrait de toutes pièces que
contient cet appareil, à l’exception de l’accès
autorisé à certaines portes ou ouvertures,
risque de vous exposer à des points de tension
dangereux ou d’autres dangers. Un remontage
incorrect peut par la suite présenter des risques
d’électrocution.
20. Vous devriez tester la réception chaque fois que
vous mettez l’appareil en fonction.
21. Examinez les composantes afin de vérifier si
celles-ci ne sont pas endommagées.
22. Soyez avisé de la perte de la confidentialité
lorsque vous utilisez les ondes publiques. Les
conversations peuvent être entendues par
d’autres moniteurs de bébé, des téléphones
sans fil, des scanneurs, etc.
23. Les enfants devraient être supervisés afin de
vous assurer qu’ils ne jouent pas avec l’appareil.
24. Le produit n’est pas conçu pour être utilisé
par des personnes (incluant des enfants) aux
capacités physiques, sensorielles ou mentales
réduites ou qui manquent d’expérience et de
connaissances, à moins qu’on leur ait donné
suffisamment de supervision ou d’instructions
relativement à l’utilisation de l’appareil par une
personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Storage
When you are not going to use the baby monitor for
some time, remove the rechargeable battery from
the parent unit. Store the parent unit, the baby unit
and the adapters in a cool and dry place.
The baby unit has infrared LEDs that allow you
to see your baby clearly at night or in a dark
room. When the baby unit being viewed
detects low light levels, the infrared LEDs are
switched on automatically. The images from
this baby unit are in black and white, and
appears on screen.
NOTES
• It is normal if you see a short white glare on your
parent unit screen as the baby unit is adapting to
the dark environment.
• When the infrared LEDs are on, the images are in
black and white. This is normal.
TIP
• Depending on the surroundings and other
interfering factors, like lightings, objects, colors
and backgrounds, the display resolution may vary.
Adjust the baby unit’s angle or place the baby
unit at a higher level to prevent glare and blurry
display.
Mises en garde
1. Utilisez et entreposez le produit à une
température entre 0˚ C (32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des
chaleurs extrêmes, ainsi qu’à la lumière directe
du soleil. Ne l’installez pas près d’une source de
chauffage.
3. Le bloc-piles ne doit pas être exposé à la
chaleur excessive telle que la lumière du soleil
ou au feu.
4. Assurez-vous que le moniteur et le cordon
de l’adaptateur sont toujours hors de portée
des enfants, àau moins 1 mètre (3 pieds) de
l’enfant ou du berceau, pour éviter tout risque de
strangulation.
5. Ne jamais placer le moniteur à l’intérieur du
berceau ou du parc de bébé. Ne jamais couvrir
le moniteur ou l’unité (s) portative avec un article
tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent
produire des interférences sur votre moniteur
vidéo et audio. Tentez d’installer votre
moniteur vidéo ou audio à l’écart des appareils
électroniques tels que des routeurs sans fil,
radios, téléphones cellulaires, interphones,
moniteurs, téléphones, ordinateurs personnels,
électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans
l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux
dispositifs numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC
(WTR)’, une firme de recherche indépendante,
a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil portatifs
et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des
aliments et drogues (FDA) des États-Unis, la firme
WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
• Vous devriez maintenir les dispositifs sans fil à
au moins six pouces du simulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil
directement sur le stimulateur cardiaque, tel que
dans une poche de chemise, lorsque celui-ci est
en marche.
L’étude effectuée par l’organisme WRS n’a pas
identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent
dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes
les normes se rapportant aux champs
électromagnétiques (EMF) standard. Si vous le
manipulez correctement en suivant les instructions
de ce guide, son utilisation sera sécuritaire pendant
de nombreuses années, selon les meilleures
évidences scientifiques dont nous disposons
aujourd’hui.
Frequently asked questions
Below are the questions most frequently asked about
the baby monitor. If you cannot find the answer to your
question, visit our website at www.vtechphones.com,
or contact 1 (800) 595-9511 for customer service.
Why does the Try the following (in the order
baby monitor listed) for common cure:
not respond
1. Disconnect the power to the
normally?
baby units and the parent unit.
2. Remove the batteries in the
parent unit. Then, install the
batteries again.
3. Wait a few seconds before
connecting power back to the
baby units and the parent unit.
4. Turn on the baby units and the
parent unit.
5. Wait for the parent unit to
synchronize with the baby units.
Allow up to one minute for this to
take place.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to
the holder of a valid proof of purchase (“Consumer”
or “you”) that the Product and all accessories
provided in the sales package (“Product”) are
free from defects in material and workmanship,
pursuant to the following terms and conditions,
when installed and used normally and in accordance
with the Product operating instructions. This limited
warranty extends only to the Consumer for Products
purchased and used in the United States of America
and Canada.
What will VTech do if the Product is not free from
defects in materials and workmanship during
the limited warranty period (“Materially Defective
Product”)?
During the limited warranty period, VTech’s
authorized service representative will repair
or replace at VTech’s option, without charge,
a Materially Defective Product. If we repair
the Product, we may use new or refurbished
replacement parts. If we choose to replace the
Product, we may replace it with a new or refurbished
Product of the same or similar design. We will
retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s
option, is your exclusive remedy. VTech will return
the repaired or replacement Products to you in
working condition. You should expect the repair or
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If
VTech repairs or replaces a Materially Defective
Product under the terms of this limited warranty,
this limited warranty also applies to the repaired
or replacement Product for a period of either (a)
90 days from the date the repaired or replacement
Product is shipped to you or (b) the time remaining
on the original one-year warranty; whichever is
longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse,
accident, shipping or other physical damage,
improper installation, abnormal operation or
handling, neglect, inundation, fire, water or other
liquid intrusion; or
2. Product that has been damaged due to repair,
alteration or modification by anyone other than an
authorized service representative of VTech; or
3. Product to the extent that the problem experienced
is caused by signal conditions, network reliability,
or cable or antenna systems; or
4. Product to the extent that the problem is caused
by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product
serial number plates or electronic serial numbers
Perhaps the parent unit is not
connected to the power. Insert the
appliance plug into the parent unit
and put the adapter in a wall socket.
Then, press and hold to switch
on the parent unit and to establish
connection with the baby unit.
Perhaps the baby unit is not
connected to the power. Insert
the appliance plug into the baby
unit and put the adapter in a wall
socket. Then, slide the ON/OFF
switch to ON to switch on the baby
unit and to establish connection
with the parent unit.
General product care
To keep this product working well and looking good,
follow these guidelines:
• Avoid putting it near heating appliances and devices
that generate electrical noise (for example, motors or
fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby
unit in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry
before you connect them to the mains again.
Night vision
4. Press SELECT to confirm your selection.
1. Press MENU when the parent unit is idle.
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product. This
product has been tested and found to comply with
the FCC criteria. The baby unit shall be installed
and used such that parts of all persons’ body are
maintained at a distance of approximately 8 in (20
cm) or more. The transmitter and antenna of the
parent unit shall be held at least 1 in (2.5 cm) from
your face.
This Class B digital apparatus complies with
Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Rename the baby units
Why don’t
the power-on
light of the
baby unit and
parent unit
go on when I
switch on the
units?
Why doesn’t
my parent
unit charge
while
connected to
AC power?
Make sure the power is not
controlled by a wall switch.
Why is my
screen in
black and
white?
The screen is in black and white
during night-time or in a dark room
when the night vision feature is
activated. This is normal.
Why do I
get glare or
blurry display
on my screen
when viewing
my baby at
night?
During night-time or in a dark
room, the surroundings and other
interfering factors, like lightings,
objects, colors and backgrounds
may affect the image quality on
your parent unit screen. Adjust the
baby unit’s angle or place the baby
unit at a higher level to prevent
glare and blurry display.
Make sure the battery is installed.
You may have used the battery for
a long time. Replace a new battery.
Why does the The parent unit and baby units may
baby monitor be too close to each other.
produce a
• Move the parent unit away from
high-pitched
the baby units until the noise
noise?
stops; OR
• Turn down the volume of your
parent unit.
Why does
the parent
unit beep?
The baby units may be out of
range. Move the parent unit closer
to the baby units (but not less than
3 feet).
If the parent unit is powered by the
provided battery, it may not have
enough charge for the parent unit to
perform normally. Charge the battery
in the parent unit for up to 3 hours.
If your parent unit is in Split-view
mode, some of your baby units
may detect sounds.
The temperature of your baby’s
room may be too high or too low.
have been removed, altered or rendered illegible;
or
6. Product purchased, used, serviced, or shipped for
repair from outside the United States of America
or Canada, or used for commercial or institutional
purposes (including but not limited to Products
used for rental purposes); or
7. Product returned without a valid proof of purchase
(see item 2 on the next page); or
8. Charges for installation or set up, adjustment of
customer controls, and installation or repair of
systems outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit
our website at www.vtechphones.com or
call 1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the
user’s manual - a check of the Product’s controls
and features may save you a service call.
Except as provided by applicable law, you assume
the risk of loss or damage during transit and
transportation and are responsible for delivery or
handling charges incurred in the transport of the
Product(s) to the service location. VTech will return
repaired or replaced Product under this limited
warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for
damage or loss of the Product in transit. If the Product
failure is not covered by this limited warranty, or proof
of purchase does not meet the terms of this limited
warranty, VTech will notify you and will request that
you authorize the cost of repair prior to any further
repair activity. You must pay for the cost of repair and
return shipping costs for the repair of Products that
are not covered by this limited warranty.
What must you return with the Product to get
warranty service?
1. Return the entire original package and contents
including the Product to the VTech service
location along with a description of the malfunction
or difficulty; and
2. Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model)
and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive
agreement between you and VTech. It supersedes
all other written or oral communications related to this
Product. VTech provides no other warranties for this
Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There
are no other express warranties. No one is authorized
to make modifications to this limited warranty and you
should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you
Why does
the parent
unit react
too quickly
to other
sounds?
The baby unit also picks up other
sounds than those of your baby.
Adjust the sensitivity level to a
lower level or lower the parent unit
speaker volume.
Why don’t
I hear a
sound/Why
can’t I hear
my baby cry?
The parent unit speaker volume
may be too low or off. Press +/VOL
to increase the volume.
Why can’t I
establish a
connection?
Why is the
connection
lost every
now and
then? Why
are there
sound
interruptions?
The baby units may be out of
range. Move the parent unit closer
to the baby units (but not less than
3 feet).
You may have set a low sound
sensitivity level. See Adjust the
sound sensitivity of the baby
unit to set to a higher level.
Other electronic products may
cause interference with your baby
monitor. Try installing your baby
monitor as far away from these
electronic devices as possible.
Important safety instructions
When using your equipment, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock and
injury, including the following:
1. Follow all warnings and instructions marked on
the product.
2. Adult setup is required.
3. This product is intended as an aid. It is not
a substitute for responsible and proper adult
supervision and should not be used as such.
4. This product is not intended for use as a medical
monitor.
5. Do not use this product near water. For example,
do not use it next to a bath tub, wash bowl,
kitchen sink, laundry tub or swimming pool, or in
a wet basement or shower.
6. CAUTION: Use only the batteries indicated in
this manual. There may be a risk of explosion
if a wrong type of battery is used for the parent
unit. Use only the supplied rechargeable battery
or replacement battery pack (BT198555/
BT298555) for the parent unit. Do not dispose of
batteries in a fire. They may explode. Dispose of
used battery according to the information in The
RBRC® seal.
7. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can
seriously damage the product.
Baby unit power adapter: Output: 5V DC 800mA
Parent unit power adapter: Output: 5V DC 1A.
8. The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
specific legal rights, and you may also have other
rights, which vary from state to state or province to
province.
Limitations: Implied warranties, including those of
fitness for a particular purpose and merchantability (an
unwritten warranty that the Product is fit for ordinary
use) are limited to one year from the date of purchase.
Some states/provinces do not allow limitations on
how long an implied warranty lasts, so the above
limitation may not apply to you. In no event shall
VTech be liable for any indirect, special, incidental,
consequential, or similar damages (including, but
not limited to lost profits or revenue, inability to use
the Product or other associated equipment, the cost
of substitute equipment, and claims by third parties)
resulting from the use of this Product. Some states/
provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof
of purchase.
Technical specifications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Channels
32
LCD
4.3” Color LCD
(WQVGA 480x272 pixel)
Nominal
effective
range
Maximum power allowed by FCC
and IC. Actual operating range may
vary according to environmental
conditions at the time of use.
Power
Parent unit: 3.7V Li-polymer battery
requirements Baby unit power adapter: Output:
5V DC @ 800mA
Parent unit power adapter: Output:
5V DC @ 1A
Specifications are subject to change without notice.
© 2017 VTech Communications, Inc.All rights
reserved. 11/17. VM4261-X_CIB_V1
Document order number: 91-010865-010-100

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:9000b653-f6e5-11e7-0000-73d02876b036
Producer                        : GPL Ghostscript 9.07
Keywords                        : ()
Modify Date                     : 2018:01:08 23:38:52+08:00
Create Date                     : 2018:01:08 23:38:52+08:00
Creator Tool                    : PDFCreator Version 1.7.1
Document ID                     : uuid:9000b653-f6e5-11e7-0000-73d02876b036
Format                          : application/pdf
Title                           : manual.pdf
Creator                         : stanleyl
Description                     : ()
Author                          : stanleyl
Subject                         : 

EXIF Metadata provided by EXIF.tools