VTech Telecommunications 80-6554-00 1.9GHz CORDLESS PHONE BASE User Manual

VTech Telecommunications Ltd 1.9GHz CORDLESS PHONE BASE Users Manual

Users Manual

User’s manual CL84109/CL84209 DECT 6.0 cordless telephone/answering system with caller ID/call waiting
8Getting startedBattery installation & chargingInstall the battery as shown below. After installing the battery, you can make and receive short calls. Place the handset in the telephone base or charger when not in use. For optimal performance, charge the handset battery for at least 16 hours before use. See the table on page 84 for battery operating times. If the battery is depleted, it may take approximately four minutes to charge the handset before it can resume screen display. The screen will continue to display LOW BATTERY until the battery has charged for approximately one hour.Step 1Plug the battery securely into the connector inside the handset battery compartment, matching the color-coded label. Insert the supplied battery with the label THIS SIDE UP facing up as indicated. Step 2Step 3Press on the recessed area and slide and slide the battery compartment cover downwards (if necessary).Align the cover flat against the battery compartment cover, then slide it upwards until it clicks into place.Charge the handset by placing it face up in the telephone base or charger. The CHARGE light on the top of the handset is on when charging.Step 4IMPORTANT INFORMATIONUse only the supplied rechargeable battery or replacement battery (model BT8001). To order, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
52. Press the tab on the base battery cover (on the bottom of the telephone base) toward the cover and swing open the battery door.3. Insert three new AAA alkaline batteries, matching the + and - signs engraved on the telephone base. 4. Replace the backup battery cover onto the telephone base, the cover will click into place if it is attached properly. During a power failure, if the backup batteries are installed, the telephone base will display CHECK AC POWER.1. Make sure no line cord is connected to the telephone base.NOTES: 1. With backup batteries, the base ringer and the handset volume will be at the lowest settings. 2. We recommend changing the batteries every nine months. Getting startedBackup battery installation and use (not included)In the event of a power failure, your telephone can still operate with limited functions if there are backup batteries (purchased separately) installed in the telephone base. If a power failure happens during a call on the corded handset, the call will continue (at the lowest volume) until you hang up; while a call on the cordless handset or speakerphone will disconnect immediately. During a power failure, you can still make and answer calls using the corded handset. However, you cannot make or answer calls on the cordless handset or speakerphone. If power resumes while you are on a call, it will continue and the telephone will reset once you hang up.Follow the steps below to install backup batteries.Battery compartment tabBASECHECK AC POWER
Important safety informationThis symbol is to alert you to important operating or servicing instructions that may appear in this user’s manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electric shock.Safety informationRead and understand all instructions in the user’s manual. Observe all markings on the product.Avoid using a telephone during a thunderstorm. There may be a slight chance of electric shock from lightning.Do not use a telephone in the vicinity of a gas leak. If you suspect a gas leak, report it immediately, but use a telephone away from the area where the gas is leaking. If this product is a cordless model, make sure the telephone base is also away from the area.Do not use this product near water, or when you are wet. For example, do not use it in a wet basement or shower, or next to a swimming pool, bathtub, kitchen sink, or laundry tub. Do not use liquids or aerosol sprays for cleaning. If the product comes in contact with any liquid, unplug any line or power cord immediately. Do not plug the product back in until it has dried thoroughly.Install this product in a protected location where no one can trip over any line or power cords. Protect cords from damage or abrasion.If this product does not operate normally, see the Troubleshooting section on pages 85-94 of this user’s manual. If you cannot solve the problem, or if the product is damaged, refer to the Limited warranty on pages 81-83. Do not open this product except as directed in your user’s manual. Opening the product or reassembling it incorrectly may expose you to hazardous voltages or other risks.Replace batteries only as described in your user’s manual. Do not burn or puncture batteries — they contain caustic chemicals.This power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling or an under-the-table/cabinet outlet.Caution: Use only the power adapter provided with this product. To obtain a replacement, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.••••••••Appendix F58
Important safety informationEspecially about cordless telephones Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone base and the handset by radio waves, so there is a possibility that your cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones. Electrical power: The telephone base of this cordless telephone must be connected to a working electrical outlet which is not controlled by a wall switch. Calls cannot be made from the handset if the telephone base is unplugged, switched off or if the electrical power is interrupted. Potential TV interference: Some cordless telephones operate at frequencies that may cause interference to TVs and VCRs. To minimize or prevent such interference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference. Rechargeable batteries: This product contains nickel-metal hydride rechargeable batteries. Exercise care in handling batteries in order not to create a short circuit with conductive material such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm. Observe proper polarity between the battery and the battery charger. Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or puncture. Like other batteries of this type, if burned or punctured, they could release caustic material which could cause injury.The RBRC™ Seal means that the manufacturer is voluntarily participating in an industry program to collect and recycle nickel-metal hydride rechargeable batteries when taken out of service within the United States. These batteries may be taken to a participating local retailer of replacement batteries or recycling center. Or you may call 1 (800) 8-BATTERY for locations accepting spent Ni-MH batteries. •••••Appendix F59
Important safety informationPrecautions for users of implanted cardiac pacemakersCardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:Pacemaker patientsShould keep wireless telephones at least six inches from the pacemaker.Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is turned ON.Should use the wireless telephone at the ear opposite the pacemaker.WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones.Especially about telephone answering systemsTwo-way recording: This unit does not sound warning beeps to inform the other party that the call is being recorded. To ensure that you are in compliance with any federal or state regulations regarding recording a telephone call, you should start the recording process and then inform the other party that you are recording the conversation.SAVE THESE INSTRUCTIONS•••Appendix F60
F�� part 68 and A�TAThis equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request.The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with the applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company.This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable the alarm equipment, consult your telephone company or a qualified installer.If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone company is required to inform you of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone company is required to notify you if such changes are planned.If this product is equipped with a corded or cordless handset, it is hearing aid compatible.Appendix G61
Appendix G62F�� part 68 and A�TAIf this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:Remain on the line and briefly explain the reason for the call before hanging up.Perform such activities in off-peak hours, such as early morning or late evening.Industry CanadaOperation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation.The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.This product meets the applicable Industry Canada technical specifications.
F�� part 15This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more. This Class B digital apparatus complies with Canadian ICES-003.Appendix H63
Technical specificationsRF frequency band 1921.536 MHz — 1928.448 MHzChannels 5Operating temperature 32°F — 122°F0°C — 50°CTelephone base voltage(AC voltage, 60Hz)96 — 127 VrmsTelephone base voltage(AC adapter output)6VDC @400mAHandset voltage 2.4 — 3.2 VDCCharger voltage(AC adapter output)6VAC @300mAReplacement battery 2.4V 750mAHDECT 6.0 digital technologyThe AT&T DECT 6.0 products offer unsurpassed range performance and sound clarity. This is achieved through a unique antenna design and advances in noise-filtering technology. An independent laboratory has confirmed that AT&T DECT 6.0 products perform up to 45% better in range competitions. Now calls can be taken in the basement, backyard and garage with exceptional sound quality. Telephone operating rangeThis cordless telephone operates within the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and telephone base can communicate over only a certain distance — which can vary with the locations of the telephone base and handset, the weather, and the construction of your home or office. Extended range and clarityThis telephone base comes with an antenna which gives much better clarity and covers a longer range than before.Appendix JOperation Operating time*Talk time (handset) Up to nine hoursTalk time (speakerphone) Up to two hoursStandby Up to five days* Operating times will vary depending on your actual use and the age of the battery. 67
Limited warrantyThe AT&T brand is used under license - any repair, replacement or warrantyservice, and all questions about this product should be directed to: Inthe United States of America, visit www.telephones.att.com or call1 (800) 222-3111. In Canada, call 1 (866) 288-4268.1. What does this limited warranty cover?The manufacturer of this AT&T-branded product warrants to the holder ofa valid proof of purchase (“CONSUMER” or “you”) that the product and allaccessories provided in the sales package (“PRODUCT”) are free from defects in(“PRODUCT”) are free from defects inPRODUCT”) are free from defects inmaterial and workmanship, pursuant to the following terms and conditions, wheninstalled and used normally and in accordance with the PRODUCT operatinginstructions. This limited warranty extends only to the CONSUMER for productspurchased and used in the United States of America and Canada.2. What will be done if the PRODUCT is not free from defects in materialsand workmanship during the limited warranty period (“materially defectivePRODUCT”)?During the limited warranty period, the manufacturer’s authorized servicerepresentative will repair or replace at the manufacturer’s option, without charge, amaterially defective PRODUCT. If the manufacturer repairs the PRODUCT, they mayuse new or refurbished replacement parts. If the manufacturer chooses to replacethe PRODUCT, they may replace it with a new or refurbished PRODUCT of thesame or similar design. The manufacturer will retain defective parts, modules, orequipment. Repair or replacement of the PRODUCT, at the manufacturer’s option,is your exclusive remedy. The manufacturer will return repaired or replacementproducts to you in working condition. You should expect the repair or replacementto take approximately 30 days.3. How long is the limited warranty period?The limited warranty period for the PRODUCT extends for ONE (1) YEAR fromthe date of purchase. If the manufacturer repairs or replaces a materially defectivePRODUCT under the terms of this limited warranty, this limited warranty alsoapplies to repaired or replacement PRODUCT for a period of either (a) 90 daysfrom the date the repaired or replacement PRODUCT is shipped to you or (b) thetime remaining on the original one-year limited warranty; whichever is longer.Appendix G80
Limited warranty4. What is not covered by this limited warranty?This limited warranty does not cover:PRODUCT that has been subjected to misuse, accident, shipping or otherphysical damage, improper installation, abnormal operation or handling,neglect, inundation, fire, water, or other liquid intrusion; orPRODUCT that has been damaged due to repair, alteration, or modification byanyone other than an authorized service representative of the manufacturer; orPRODUCT to the extent that the problem experienced is caused by signalconditions, network reliability or cable or antenna systems; orPRODUCT to the extent that the problem is caused by use with non-AT&Taccessories; orPRODUCT whose warranty/quality stickers, PRODUCT serial number plates orelectronic serial numbers have been removed, altered or rendered illegible; orPRODUCT purchased, used, serviced, or shipped for repair from outside theUnited States of America or Canada, or used for commercial or institutionalpurposes (including but not limited to products used for rental purposes); orPRODUCT returned without valid proof of purchase (see item 6 below); -or-Charges for installation or setup, adjustment of customer controls, andinstallation or repair of systems outside the unit.5. How do you get warranty service?To obtain warranty service in the United States of America, visitwww.telephones.att.com or call 1 (800) 222-3111. In Canada, call1 (866) 288-4268. NOTE: Before calling for service, please review theuser’s manual; a check of the PRODUCT controls and features may save you aservice call.Except as provided by applicable law, you assume the risk of loss or damageduring transit and transportation and are responsible for delivery or handlingcharges incurred in the transport of the PRODUCT(s) to the service location.The manufacturer will return repaired or replaced PRODUCT under this limitedwarranty to you. Transportation, delivery or handling charges are prepaid. Themanufacturer assumes no risk for damage or loss of the PRODUCT in transit. If thePRODUCT failure is not covered by this limited warranty, or proof of purchase doesnot meet the terms of this limited warranty, the manufacturer will notify you andwill request that you authorize the cost of repair prior to any further repair activity.You must pay for the cost of repair and return shipping costs for the repair ofproducts that are not covered by this limited warranty.••••••••Appendix G81
www.telephones.att.com© 2008 Advanced American Telephones. All rights reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P. d/b/a AT&T Intellectual Property licensed to Advanced American Telephones. Printed in �hina. Issue 1 AT&T 10/08.

Navigation menu