VTech Telecommunications 80-8535-00 1.9GHz DECT Cordless Phone User Manual CS6519 X SIMCIB ULAPPROVAL V1 20111013

Download:
Mirror Download [FCC.gov]
Document ID	1616341
Application ID	czFuzNW0MXIeRzpmoBcxRQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	251.4kB (3142438 bits)
Date Submitted	2012-01-09 00:00:00
Date Available	2012-01-09 00:00:00
Creation Date	2011-12-30 15:35:36
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2011-12-30 15:35:36
Document Title	CS6519-X_SIMCIB_ULAPPROVAL_V1_20111013.pdf
Document Creator	PScript5.dll Version 5.2
Document Author:	kwkwan

User’s manual
CS6519/CS6519-2
DECT 6.0 cordless telephone
Introduction
To protect our environment and conserve natural resources, this user’s manual
provides you with the basic installation and use instructions. A limited set of features
are described in abbreviated form.
Please refer to the complete online user’s manual for a full set of installation and
operation instructions at www.vtechphones.com.
Before using this VTech product, please read Important safety instructions on
page 10 of this user’s manual.
Table of contents
Parts checklist ...................................... 1
Telephone base and charger
installation ........................................ 2
Battery installation ................................ 2
Battery charging ................................... 2
Tabletop to wall mount
installation ........................................ 3
Handset overview ................................. 3
Telephone base overview..................... 4
Using the handset menu....................... 4
Telephone settings ............................... 4
Telephone operation............................. 5
Directory ...............................................6
Speed dial............................................. 7
Caller ID................................................7
About the answering system ................ 8
Answering system settings ................... 8
Answering system operation ................ 8
Add and register a handset .................. 9
Replace a handset................................ 9
Troubleshooting.................................... 9
Important safety instructions................. 11
Precautions for users of implanted
cardiac pacemakers ......................... 12
Operating range.................................... 12
Maintenance ......................................... 12
About cordless telephones ................... 12
ÂŽ
The RBRC seal ................................... 13
Limited warranty ................................... 13
FCC, ACTA and IC regulations ............ 13
6GEJPKECNURGEKĹżECVKQPU........................ 14
Parts checklist
Your telephone package contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
Battery compartment
cover
(1 for CS6519 and
2 for CS6519-2)
Handset
Telephone line cord
Battery
(1 for CS6519,
2 for CS6519-2)
Charger and charger
adapter
Telephone base
(1 for CS6519 and
2 for CS6519-2)
(1 for CS6519-2)
Quick start guide
User’s manual
User’s manual
Quick start guide
Telephone base
power adapter
Wall mount
bracket
Telephone base and charger installation
Install the telephone base and charger as shown below.
Charger adapter
Telephone wall jack
Telephone base
power adapter
#&5.ĹżNVGT PQVKPENWFGF 
is required if you have DSL
high-speed Internet service
Electrical outlet
not controlled by
a wall switch
Electrical outlet
not controlled
by a wall switch
Telephone line cord
Charger
Telephone base
•
•
Use only the power adapter and battery supplied with this product. To order a
replacement, visit our website at www.vtechphones.com or call 1 (800) 595-9511.
In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
6JGRQYGTCFCRVGTKUKPVGPFGFVQDGEQTTGEVN[QTKGPVGFKPCXGTVKECNQTƀQQTOQWPV
position. The prongs are not designed to hold the plug in place if it is plugged into
a ceiling, under-the-table or cabinet outlet.
Battery installation
Install the battery as shown below.
1. Plug the battery connector
securely into the socket.
2. Place the battery with the label
THIS SIDE UP facing up and
the wires inside the battery
compartment.
3. Slide the battery compartment
cover towards the center of the
handset until it clicks into place.
4. Place the handset in the telephone
base or charger to charge.
CHARGE light
remains on
when charging.
If the handset will not be used for a long time, disconnect and remove the battery to
prevent possible leakage.
Battery charging
Once you have installed the battery, the screen indicates the battery status (see
the table below). For best performance, keep the handset in the telephone base or
charger when not in use. The battery is fully charged after 10 hours of continuous
charging. Refer to the online user’s manual for battery operating times.
Battery indicators
Battery status
Action
The screen is blank,
or shows PLACE IN
CHARGER and ƀCUJGU
The battery has no charge or
very little charge. The handset
cannot be used.
Charge without interruption
(at least 30 minutes).
The screen shows
LOW BATTERY and
ƀCUJGU
The battery has enough
charge to be used for a
short time.
Charge without interruption
(at least 30 minutes).
The screen shows
HANDSET X.
The battery is charged.
To keep the battery charged,
place it in the telephone
base or charger when not
in use.
• If you place the handset in the telephone base or charger without plugging in the
battery, the screen displays NO BATTERY.
Tabletop to wall mount installation
The telephone comes ready for tabletop use. Follow the steps below to mount your
telephone on a wall.
1. Plug one end of the telephone line
2. Position the telephone base against
the wall mount bracket as shown.
cord into the TEL LINE jack at the
Insert the extended tabs marked B
bottom of the telephone base and
on the wall mount bracket into the
the base power adapter into the
slots marked B on the back of the
POWER jack.
telephone base. Push the telephone
base down until it clicks securely.
4. Align the holes on the bracket with
the standard wall plate and slide the
bracket down until it locks securely.
Bundle the telephone line cord
and power adapter cord neatly
with twist ties.
3. Route the telephone line cord
through the hole on the wall mount
bracket and plug it into the telephone
wall jack. Route the power cord out
of the telephone base and plug it into
an electrical outlet not controlled by a
wall switch.
Handset overview
CHARGE light
On when the handset is charging.
CID /VOLUME
Review the call log when the phone
is not in use.
Decrease the listening volume
during a call or message playback.
Scroll down while in a menu, or in
the directory, call log or redial list.
Move the cursor to the left when
entering numbers or names.
/VOLUME
Review the directory when the
phone is not in use.
Increase the listening volume
during a call or message
playback.
Scroll up while in a menu, or in
the directory, call log or redial list.
Move the cursor to the right when
entering numbers or names.
MENU/SELECT
Show the menu.
While in a menu, press to select
an item, or save an entry or
setting.
REDIAL/PAUSE
Press repeatedly to review the
redial list.
Press and hold to insert a dialing
pause while entering numbers.
OFF/CANCEL
Hang up a call.
Silence the ringer temporarily while
the handset is ringing.
Press and hold to erase the missed
call indicator while the phone is not
in use.
Press to return to the previous
menu, or press and hold to return
to idle mode, without making
changes.
/FLASH
Make or answer a call.
Answer another incoming call
during a call.
Press repeatedly to add or
remove 1 in front of the call log
entry before dialing or saving it to
the directory.
# (pound key)
Press repeatedly to show other
dialing options when reviewing a
call log entry.
Dialing keys
Enter numbers or characters.
INT (intercom)
Start an intercom conversation or
transfer a call (for multi-handset
models only).
TONE
Switch to tone dialing
temporarily during a call.
MUTE/DELETE
Mute the microphone during a call.
Delete digits or characters while
using the dialling keys.
Silence the ringer temporarily while
the handset is ringing.
Delete the displayed entry while in
the directory, call log or redial list.
(speakerphone)
Make or answer a call using the
handset speakerphone.
During a call, press to switch
between the speakerphone and the
handset.
Telephone base overview
IN USE light
Flashes when there is an incoming
call, or another telephone sharing the
same line is in use.
On when the handset is in use, or
the answering system is answering
a call.
/FIND HANDSET
Press once and then release to page
all system handsets.
Using the handset menu
1.
2.
3.
•
•
Press MENU when the phone is not in use.
Press or until the screen displays the desired feature menu.
Press SELECT to enter that menu.
To return to the previous menu, press CANCEL.
To return to idle mode, press and hold CANCEL.
Telephone settings
Default settings are indicated by an asterisk(*).
Screen display
Function
Options
LCD LANGUAGE
Set the screen display language.
ENGLISH*
FRANÇAIS
ESPAÑOL
CLR VOICEMAIL
Turn off the voicemail indicators.
TURN OFF
INDICATOR?
KEY TONE
Turn an audible beep on or off whenever a key
is pressed.
ON*
OFF
SET DATE/TIME
Set the date and time shown on
the handset.
-:-- --/--
HOME AREA CODE
Enter your home area code if you dial only seven
digits for local calls.
___
DIAL MODE
Set the telephone to be tone or
pulse dialing.
TONE*
PULSE
The following are some of the telephone features you may wish to set. Refer to
Telephone settings in the online user’s manual for detailed instructions on setting
all telephone features.
Ringer volume (handset)
You can adjust the ringer volume level, or turn the ringer off.
1. Press MENU when the handset is not in use.
2. Scroll to >RINGERS then press SELECT twice.
3. Press or to adjust the volume, then press SELECT to save.
•
•
If the handset ringer volume is set to off, that handset is silenced for all incoming
calls except paging tone.
The ringer volume also determines the ringer volume of the intercom calls and the
volume of the paging tone.
Set date and time
If you subscribe to caller ID service, the day, month and time are set automatically
with each incoming call. You can also set the date and time manually.
1. Press MENU when the handset is not in use.
2. Scroll to select >SETTINGS, then press SELECT.
3. Scroll to select >SET DATE/TIME, then press SELECT.
4. Use the dialing keys (0-9) to enter the month, date and year, then press SELECT.
5. Use the dialing keys (0-9) to enter the hour and minute.
6. Press or to choose AM or PM, or press 2 for AM or 7 for PM. Press
SELECT to save.
Voicemail indicators
If you subscribe to voicemail service offered by your telephone service provider,
NEW VOICEMAIL and
appear on the handset when you have new voicemail
messages. Contact your telephone service provider for more information and
assistance about using your voicemail service. Refer to Clear voicemail indicators
in the online user’s manual on how to clear the voicemail indicators.
Telephone operation
Make a call
•
Press
or
then dial the telephone number.
Answer a call
•
Press
or any dialing key.
End a call
•
Press OFF or put the handset to the telephone base or charger.
Speakerphone
•
During a call, press
handset use.
to switch between speakerphone and normal
Volume
•
During a call, press
/VOLUME or
/VOLUME to adjust the listening volume.
The handset earpiece volume setting and speakerphone volume setting are
independent.
Mute
The mute function allows you to hear the other party but the
other party cannot hear you.
1. During a call, press MUTE. The handset displays MUTE.
2. Press MUTE again to resume the conversation.
Call waiting
When you subscribe to call waiting service from your telephone service provider,
you hear an alert tone if there is an incoming call while you are on another call.
• Press FLASH to put the current call on hold and take the new call.
• Press FLASH at any time to switch back and forth between calls.
Temporary ringer silencing
When the telephone is ringing, you can temporarily silence the ringer of the handset
without disconnecting the call. The next call rings normally at the preset volume.
• To silence the handset ringer, press OFF or MUTE on the handset.
RINGER MUTED and
display.
Temporary tone dialing
If you have pulse (rotary) service only, you can switch from pulse
to tone dialing temporarily during a call.
1. During a call, press TONE .
2. Use the dialing keys to enter the relevant number. The
telephone sends touch-tone signals.
3. The telephone automatically returns to pulse dialing mode
after you end the call.
Find handset
7UGVJKUHGCVWTGVQĹżPFCNNU[UVGOJCPFUGVU
To start paging:
• Press /FIND HANDSET on the telephone base once and
then release. All idle handsets ring and their screens
show ** PAGING **.
To end paging:
• Press /FIND HANDSET again on the telephone base once and then release.
or any dialing key on the handset.
• Press
• Place the handset in the telephone base or charger.
Do not press and hold /FIND HANDSET for more than four seconds. It may lead
to handset deregistration.
Redial list
Each handset stores the last 10 telephone numbers dialed.
To review and dial a number from the redial list:
1. Press REDIAL when the handset is not in use.
2. Press , , or REDIAL repeatedly until the desired
entry displays.
to dial.
3. Press
To delete a redial entry:
When the desired redial entry displays, press DELETE.
Chain dialing
Use this feature to initiate a dialing sequence from numbers stored in the directory,
call log or redial list while you are on a call. Chain dialing can be useful if you wish
to access other numbers (such as bank account numbers or access codes) from the
directory, call log or redial list.
To access a number in the directory, call log or redial list while on a call:
1. To enter the directory, press MENU, then scroll to >DIRECTORY, and then
press SELECT.
-ORTo enter the call log, press MENU, then scroll to >CALL LOG, and then
press SELECT.
-ORTo enter the redial list, press REDIAL.
2. Press or to scroll to the desired entry.
3. Press SELECT to dial the displayed number.
Join a call in progress
You can use up to four system handsets at a time on an outside call. You can buy
additional expansion handsets (CS6409) for this telephone base. You can register
WRVQĹżXGJCPFUGVUVQVJGVGNGRJQPGDCUG
or
on another handset to join the call.
• When a handset is on a call, press
• Press OFF to exit the call. The call continues until all handsets hang up.
Intercom
Use the intercom features for conversations between two handsets.
1. Press INT on your handset when not in use. When you have three or more
handsets, use the dialing keys to enter a destination handset number.
, , INT or any dialing key on the
2. To answer the intercom call, press
destination handset.
3. To end an intercom call, press OFF or place the handset back in the telephone
base or charger.
Answer an incoming call during an intercom call
If you receive an outside call during an intercom call, there is an alert tone.
. The intercom call ends automatically.
• To answer the outside call, press
• To end the intercom call without answering the outside call, press OFF. The
intercom call ends and the telephone continues to ring.
Call transfer using intercom
Use the intercom feature to transfer an outside call to another system handset.
1. During a call, press INT. When you have three or more handsets, use the
dialing keys to enter a destination handset number.
, , INT or any dialing key on the
2. To answer the intercom call, press
destination handset. The outside call is now on hold and both handsets show
INTERCOM. You can have a private conversation with the destination handset.
3. From this intercom call, you have the following options:
• You can let the destination handset join you on the outside call in a three-way
conversation. Press and hold INT on the original handset.
• You can transfer the call. Press OFF, or place your handset back
in the telephone base or charger. Your handset screen shows
CALL TRANSFERRED. The destination handset then automatically
connects to the outside call.
• You can press INT to switch between the outside call (OUTSIDE CALL
displays) and the intercom call (INTERCOM displays).
• The destination handset can end the intercom call by pressing OFF, or by
placing the handset back in the telephone base or charger. The outside call
continues with the original system handset.
Directory
The directory can store up to 50 entries and are shared by all system handsets.
To add a directory entry:
1. Press MENU/SELECT twice.
2. Scroll to >ADD CONTACT then press SELECT.
• Use the dialing keys to enter the number (up to 30 digits).
-OR• Copy a number from the redial list by pressing REDIAL and then press ,
or REDIAL repeatedly to select a number. Press SELECT.
3. Press SELECT to move to the name.
4. Use the dialing keys to enter the name (up to 15 characters). Additional key presses
show other characters of that particular key.
5. Press SELECT to save.
While entering names and numbers, you can:
• Press DELETE to backspace and erase a digit or character.
• Press and hold DELETE to erase the entire entry.
• Press and hold PAUSE to insert a dialing pause (for entering phone numbers only).
• Press or to move the cursor to the left or right.
• Press 0 to add a space (for entering names only).
To review and dial from the directory:
Entries are sorted alphabetically.
1. Press
when the handset is not in use.
2. Scroll to browse through the directory, or use the dialing keys to start a
name search.
3. When the desired entry appears, press
or
to dial.
To edit a directory entry:
1. When the desired entry displays, press SELECT.
2. Use the dialing keys to edit the number, then press SELECT.
3. Use the dialing keys to edit the name, then press SELECT to save.
To delete a directory entry:
1. When the desired entry displays, press DELETE.
2. When the screen displays DELETE CONTACT?, press SELECT.
Speed dial
You can copy up to 10 directory entries into the speed dial locations so that you can
dial these numbers using fewer keys than usual.
To store a speed dial entry:
1. Press MENU/SELECT twice when the handset is not in use.
2. Scroll to >SPEED DIAL, then press SELECT.
3. Scroll to a desired speed dial location, then press SELECT.
4. Scroll to a desired directory entry, then press SELECT to save.
To dial a speed dial entry:
1. Press and hold a dialing key (0-9) to display the desired speed dial entry when
the handset is not in use.
2. Press
or
to dial the displayed phone number.
To delete a speed dial entry:
When the desired entry displays, press DELETE.
Caller ID
This product supports caller ID services provided by most telephone service
providers. Depending on your service subscription, you may see the caller’s name,
number, date and time of calls that are sent by your telephone service provider after
VJGĹżTUVQTUGEQPFTKPI
Call log
The call log stores up to 50 entries. If you answer a call before the caller information
appears, it will not be saved in the call log.
• The handset displays XX MISSED CALLS when there are calls that have not
been reviewed in the call log.
• If you want to erase the missed call indicator, press and hold CANCEL on the
idle handset.
To review and dial a number in the call log:
1. Press CID when the handset is not in use.
2. Scroll to browse through the call log. When the desired entry appears:
• Press # (pound key) repeatedly to show different dialing options.
• Press 1 repeatedly if you need to add or remove 1 in front of the
phone number.
3. Press
to dial the displayed number.
To save a call log entry to the directory:
1. When the desired call log entry displays, press SELECT.
2. Use the dialing keys to modify the number, then press SELECT.
3. Use the dialing keys to modify the name, then press SELECT to save.
To delete one call log entry:
• When the desired call log entry displays, press DELETE.
To delete all call log entries:
• Press MENU when the handset is not in use. Scroll to >CALL LOG and then
press SELECT. Scroll to >DEL ALL CALLS and then press SELECT twice.
Add and register a handset
The handsets provided with your telephone system are already registered. Each
handset is assigned a number that displays on the handset. Additional handsets
registered to the telephone system are assigned numbers in the sequential order.
6JKUVGNGRJQPGU[UVGOCEEQOOQFCVGUWRVQĹżXGJCPFUGVU
You can add new handsets (CS6409, purchased separately) to your telephone
system. Each handset must be registered with the telephone base before use.
9JGPĹżTUVRWTEJCUGFCPFRTQRGTN[EJCTIGFGCEJGZRCPUKQPJCPFUGVUJQYU
1.PRESS FIND HS ON BASE 4 SEC and 2.THEN PRESS # ON HANDSET
alternately. Charge the handset before registering it to the telephone base.
To register a handset:
1. Place the non-registered handset in the telephone base or charger.
2. On the telephone base, press and hold /FIND HANDSET for about
four seconds until the red IN USE light turns on.
3. On the handset, press # (pound key) then the handset shows REGISTERING.....
PLEASE WAIT. Then the handset shows HANDSET REGISTERED and you
hear a beep when the registration process completes. The registration process
takes about 60 seconds to complete.
Replace a handset
If you want to replace a handset or reassign the designated handset number of a
registered handset, you must deregister all handsets and then individually register
each handset.
To deregister all handsets:
1. Press and hold /FIND HANDSET on the telephone base for about 10 seconds
until the IN USENKIJVQPVJGVGNGRJQPGDCUGVWTPUQPCPFUVCTVUƀCUJKPI
2. Press and release /FIND HANDSET again. You must press /FIND HANDSET
while the IN USENKIJVKUUVKNNƀCUJKPI6JGIN USENKIJVƀCUJGUHQTCRRTQZKOCVGN[
ĹżXGUGEQPFU
3. All handsets show 1.PRESS FIND HS ON BASE 4 SEC and
2.THEN PRESS # ON HANDSET alternately when the deregistration process
completes. The deregistration process takes about 10 seconds to complete.
Troubleshooting
+H[QWJCXGFKHĹżEWNV[YKVJ[QWTVGNGRJQPGRNGCUGVT[VJGUWIIGUVKQPUDGNQY(QTEWUVQOGT
service, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada,
go to www.vtechcanada.com or call 1 (800) 267-7377.
My telephone does not work at all.
• Make sure the battery is installed and charged correctly. For optimum daily performance,
return the handset to the telephone base or charger after use.
• Make sure the power adapter is securely plugged into an outlet not controlled by a wall switch.
• /CMGUWTGVJGVGNGRJQPGNKPGEQTFKURNWIIGFſTON[KPVQVJGVGNGRJQPGDCUGCPFVJGYCNNLCEM
• Unplug the electrical power to the telephone base. Wait for approximately 15 seconds,
then plug it back in. Allow up to one minute for the cordless handset and telephone base to
synchronize.
• Charge the battery in the handset for up to 10 hours.
• If the battery is completely depleted, it may take up to 30 minutes to charge the handset
before LOW BATTERY appears on the screen.
• Remove and install the battery again. If that still does not work, it may be necessary to
purchase a new battery.
• Disconnect the telephone base from the telephone wall jack and plug in a working
telephone. If the other telephone does not work, the problem is probably in the wiring or
telephone service. Contact your telephone service provider.
There is no dial tone.
•
•
•
•
Try all the above suggestions.
Move the handset closer to the telephone base. It may be out of range.
The telephone line cord may be defective. Install a new telephone line cord.
Disconnect the telephone base from the telephone wall jack and connect a different telephone.
If there is no dial tone on this telephone either, the problem is in your wiring or telephone
service. Contact your telephone service provider.
I cannot dial out.
• Try all the above suggestions.
• Make sure there is a dial tone before dialing. It is normal if the handset takes a second or
two to synchronize with the telephone base before producing a dial tone. Wait an extra
second before dialing.
• If other telephones in your home are having the same problem, the problem is in the wiring
or telephone service. Contact your telephone service provider (charges may apply).
• Eliminate any background noise. Mute the cordless handset before dialing, or dial from
another room in your home with less background noise.
The handset shows 1.PRESS FIND HS ON BASE 4 SEC and 2.THEN PRESS #
ON HANDSET alternately and it does not work at all.
• The handset may be deregistered from the telephone base. Refer to Add and register a
handset on page 8 to register the handset to the telephone base.
LOW BATTERY shows on the handset screen.
• Place the handset in the telephone base or charger for recharging.
• Remove and install the battery again and use it until fully depleted, then charge the handset
in the telephone base or charger for up to 10 hours.
• If the above measures do not correct the problem, replace the battery.
The battery does not charge in the handset or the handset battery does not
accept charge.
• Make sure the handset is placed in the telephone base or charger correctly. The CHARGE
light on the handset should be on.
• Remove and install the battery again, then charge for up to 10 hours.
• If the handset is in the telephone base but the CHARGE light on the handset is not on, refer
to The CHARGE light is off below.
• If the battery is completely depleted, charge the handset for at least 30 minutes before use.
• Purchase a new battery. Refer to Battery installation on page 2.
The telephone does not ring when there is an incoming call.
• Make sure the handset ringer volume is not set to off and the telephone base ringer volume
is not set to zero.
• Make sure the telephone line cord and power adapter are plugged in properly.
• The handset may be too far from the telephone base. Move it closer to the telephone base.
• There may be too many extension phones on the telephone line to allow all of them to ring
simultaneously. Unplug some of them.
• If other telephones in your home are having the same problem, the problem is in the wiring
or telephone service. Contact your telephone service provider (charges may apply).
• Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible from
these types of electronic devices.
• Test a working telephone at the telephone wall jack. If another telephone has the same
problem, the problem is in the telephone wall jack. Contact your telephone service provider
(charges may apply).
• The telephone line cord may be defective. Install a new telephone line cord.
• Remove and install the battery again and then place the handset in the telephone base.
• Wait for the handset to synchronize with the telephone base. Allow up to one minute for this
to take place.
My caller ID features are not working properly.
• Caller ID is a subscription service. You must subscribe to this service from your telephone
service provider for this feature to work on your telephone.
• The caller may not be calling from an area which supports caller ID.
• Both your and your caller’s telephone service providers must use equipment compatible with
the caller ID service.
• 6JGECNNGT+&KPHQTOCVKQPUJQYUCHVGTVJGſTUVQTUGEQPFTKPI
• If you subscribe to high-speed Internet service (DSL - digital subscribe line) through
[QWTVGNGRJQPGNKPG[QWOWUVKPUVCNNC&5.ĹżNVGTDGVYGGPVJGVGNGRJQPGline cord and
VJGVGNGRJQPGYCNNLCEM6JGĹżNVGTRTGXGPVUPQKUGCPFECNNGT+&RTQDNGOUECWUGFD[&5.
KPVGTHGTGPEG%QPVCEV[QWT&5.UGTXKEGRTQXKFGTHQTOQTGKPHQTOCVKQPCDQWV&5.ĹżNVGTU
My handset beeps and is not performing normally.
• Make sure the power cord is securely plugged into the telephone base. Plug the telephone
base into a different working electrical outlet not controlled by a wall switch.
• Move the handset closer to the telephone base. It may be out of range.
• Reset the telephone base by unplugging the electrical power to the base. Wait for 15 seconds
and plug it back in again. Allow up to one minute for the cordless handset and the telephone
base to synchronize.
• Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible
from these types of electronic devices.
There is interference during a telephone conversation.
My calls fade out when I am using the cordless handset.
• The handset may be out of range. Move it closer to the telephone base.
• If you subscribe to high-speed Internet service (DSL - digital subscriber line) through
[QWTVGNGRJQPGNKPG[QWOWUVKPUVCNNC&5.ĹżNVGTDGVYGGPVJGVGNGRJQPGNKPGEQTFCPF
VJGVGNGRJQPGYCNNLCEM6JGĹżNVGTRTGXGPVUPQKUGCPFECNNGT+&RTQDNGOUECWUGFD[&5.
KPVGTHGTGPEG%QPVCEV[QWT&5.UGTXKEGRTQXKFGTHQTOQTGKPHQTOCVKQPCDQWV&5.ĹżNVGTU
• Appliances or other cordless telephones plugged into the same circuit as the telephone base
can cause interference. Try moving the appliance or telephone base to another outlet.
• Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as
possible from these types of electronic devices.
• If your telephone is plugged in with a modem or a surge protector, plug the telephone (or
modem/surge protector) into a different location. If this doesn’t solve the problem, relocate
your telephone or modem farther apart from each other, or use a different surge protector.
• The location of your telephone base can impact the performance of your cordless phone. For
DGVVGTTGEGRVKQPKPUVCNNVJGVGNGRJQPGDCUGKPCEGPVTCNK\GFNQECVKQPYKVJKP[QWTJQOGQTQHĹżEG
away from walls or other obstructions. In many environments, elevating the telephone base
improves overall performance.
• Disconnect the telephone base from the telephone wall jack and plug in a corded telephone. If
calls are still not clear, the problem is probably in the wiring or telephone service. Contact your
telephone service provider (charges may apply).
• If other telephones in your home are having the same problem, the problem is in the wiring or
telephone service. Contact your telephone service provider (charges may apply).
The handset shows OUT OF RANGE OR NO PWR AT BASE.
• The handset may be out of range. Move it closer to the telephone base.
• Make sure the power cord is securely plugged into the telephone base. Use a working
electrical outlet not controlled by a wall switch.
• Reset your telephone by unplugging the power adapter from the telephone base. Disconnect
the battery from the cordless handset. Wait for 15 seconds, then plug in the power adapter
and reinstall the battery. Place the handset in the telephone base and allow up to one minute
for the handset and telephone base to synchronize.
• Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible
from these types of electronic devices.
NEW VOICEMAIL and
show on the display and I don’t know why.
appear on the display, then your telephone has received a
• If NEW VOICEMAIL and
signal from your telephone service provider that you have a voicemail message waiting
for you to retrieve from your telephone service provider. Contact your telephone service
provider for more information on how to access your voicemail.
The answering system does not answer after correct number of rings.
• Make sure the answering system is on. When the answering system is on, ANS ON should
show on the handset and the /ANSWER ON/OFF light is lit on the telephone base.
• If toll saver is selected, the number of rings changes to two when there are new messages.
• If the memory is full or the answering system is off, the answering system answers after 10
rings. In some cases, the answering system is affected by the ringing system used by the
telephone service provider.
• If you subscribe to voicemail service, change the number of rings so that your answering
system answers before your voicemail answers. To get help with your voicemail settings,
contact your telephone service provider.
• If there is a fax machine connected to the same telephone line, try disconnecting the fax
machine. If that solves the problem, consult your fax machine documentation for information
on compatibility with answering systems.
The answering system does not record messages.
• Make sure the answering system is on.
• Make sure the memory of the answering system is not full. When the answering machine
memory is full, it does not record new messages until some old messages are deleted.
• If you subscribe to voicemail service, change the number of ring so that your answering
system answers before your voicemail answers. To determine how many rings activate your
voicemail, contact your telephone service provider.
• If there is a fax machine connected to the same telephone line, try disconnecting the fax
machine. If that solves the problem, consult your fax machine documentation for information
on compatibility with answering systems.
The messages on the answering system are incomplete.
• If a caller leaves a very long message, part of it may be lost when the answering system
disconnects the call after the preset recording time.
• If the memory on the answering system becomes full during a message, the answering
system stops recording and disconnects the call.
• If the caller’s voice is very soft, the answering system may stop recording and disconnect
the call.
Common cure for electronic equipment.
• If the telephone is not responding normally, put the cordless handset in the telephone base.
If this does PQVĹżZVJGRTQDNGO, do the following (in the order listed):
1. Disconnect the power to the telephone base.
2. Disconnect the battery on the cordless handset.
3. Wait a few minutes before connecting power to the telephone base.
4. Install the battery again and place the cordless handset in the telephone base .
5. Wait for the cordless handset to synchronize with the telephone base. Allow up one
minute for this to take place.
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk
QHĹżTGGNGEVTKEUJQEMCPFKPLWT[KPENWFKPIVJGHQNNQYKPI
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
4. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To
protect them from overheating, these openings must not be blocked by placing the product on a soft surface
such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This
product should not be placed in any area where proper ventilation is not provided.
7. This product should be operated only from the type of power source indicated on the marking label. If you are
PQVUWTGQHVJGV[RGQHRQYGTUWRRN[KP[QWTJQOGQTQHĹżEGEQPUWNV[QWTFGCNGTQTNQECNRQYGTEQORCP[
8. Do not allow anything to rest on the power cord. Do not install this product where the cord may be
walked on.
9. Never push objects of any kind into this product through the slots in the telephone base or handset
because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind
on the product.
10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized
UGTXKEGHCEKNKV[1RGPKPIQTTGOQXKPIRCTVUQHVJGVGNGRJQPGDCUGQTJCPFUGVQVJGTVJCPURGEKĹżGF
access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause
electric shock when the product is subsequently used.
11. Do not overload wall outlets and extension cords.
12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the
following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operation instructions. Improper adjustment of other controls may
result in damage and often requires extensive work by an authorized technician to restore the product
to normal operation.
E. If the product has been dropped and the telephone base and/or handset has been damaged.
F. If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of
electric shock from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances,
a spark may be created when the adapter is plugged into the power outlet, or when the handset is
replaced in its cradle. This is a common event associated with the closing of any electrical circuit.
The user should not plug the phone into a power outlet, and should not put a charged handset into
VJGETCFNGKHVJGRJQPGKUNQECVGFKPCPGPXKTQPOGPVEQPVCKPKPIEQPEGPVTCVKQPUQHƀCOOCDNG or
ƀCOGUWRRQTVKPIICUGUWPNGUUVJGTGKUCFGSWCVGXGPVKNCVKQP#URCTMKPUWEJCPGPXKTQPOGPV could
ETGCVGCĹżTGQTGZRNQUKQP5WEJGPXKTQPOGPVUOKIJVKPENWFGOGFKECNWUGQHQZ[IGPYKVJQWV adequate
ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
15. Only put the handset of your telephone next to your ear when it is in normal talk mode.
16. 6JGRQYGTCFCRVGTUCTGKPVGPFGFVQDGEQTTGEVN[QTKGPVGFKPCXGTVKECNQTƀQQTOQWPVRQUKVKQP6JG
prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or
cabinet outlet.
SAVE THESE INSTRUCTIONS
10
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation
of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six inches from the pacemaker.
• Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is
turned ON.
• Should use the wireless telephone at the ear opposite the pacemaker. WTR’s evaluation did not identify
any risk to bystanders with pacemakers from other persons using wireless telephones.
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications
Commission (FCC). Even so, this handset and telephone base can communicate over only a certain distance
- which can vary with the locations of the telephone base and handset, the weather, and the layout of your home
QTQHĹżEG
When the handset is out of range, the handset displays OUT OF RANGE OR NO PWR AT BASE.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect
well when you press
. Move closer to the telephone base, then press
to answer the call.
If the handset moves out of range during a telephone conversation, there may be interference. To improve
reception, move closer to the telephone base.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you ever need
to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with
wet hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety,
take caution when using electrical appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft
cloth slightly dampened with water or mild soap. Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or standing
in the water. If the telephone base should fall into the water, DO NOT RETRIEVE IT UNTIL YOU
UNPLUG THE POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the
telephone by the unplugged cords.
About cordless telephones
• Privacy: The same features that make a cordless telephone convenient create some
limitations. Telephone calls are transmitted between the telephone base and the cordless handset by radio
waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio
receiving equipment within range of the cordless handset. For this reason, you should not think of cordless
telephone conversations as being as private as those on corded telephones.
• Electrical power: The telephone base of this cordless telephone must be connected to a working electrical
outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the
cordless handset if the telephone base is unplugged, switched off or if the electrical power is interrupted.
• Potential TV interference: Some cordless telephones operate at frequencies that may cause interference
to televisions and VCRs. To minimize or prevent such interference, do not place the telephone base of
the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless
telephone farther away from the TV or VCR often reduces or eliminates the interference.
• Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with
conducting material such as rings, bracelets, and keys. The battery or conductor may overheat and cause
harm. Observe proper polarity between the battery and the battery charger.
• Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn
or puncture the battery. Like other batteries of this type, if burned or punctured, they could release caustic
material which could cause injury.
The RBRCÂŽ seal
The RBRCÂŽ seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and recycle these batteries at the end of their useful lives, when
taken out of service within the United States and Canada.
The RBRCÂŽ program provides a convenient alternative to placing used nickel-metal hydride batteries into the
trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers
participating in the RBRCÂŽ program or at authorized VTech product service centers. Please call 1 (800) 8
BATTERYTM for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s
involvement in this program is part of its commitment to protecting our environment and conserving natural
resources.
RBRCÂŽ is a registered trademark of Rechargeable Battery Recycling Corporation.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or
“you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in
material and workmanship, pursuant to the following terms and conditions, when installed and used normally
and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer
for Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the
limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at
VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new
or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or
refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the
repaired or replacement Products to you in working condition. You should expect the repair or replacement to
take approximately 30 days.
11
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs
or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies
to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement
Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper
KPUVCNNCVKQPCDPQTOCNQRGTCVKQPQTJCPFNKPIPGINGEVKPWPFCVKQPĹżTGYCVGTQTQVJGTNKSWKFKPVTWUKQPQT
 2TQFWEVVJCVJCUDGGPFCOCIGFFWGVQTGRCKTCNVGTCVKQPQTOQFKĹżECVKQPD[CP[QPGQVJGTVJCPCP
authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or
cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have
been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or
Canada, or used for commercial or institutional purposes (including but not limited to Products used for
rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems
outside the unit.
How do you get warranty service?
To obtain warranty service, please visit our website at www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and
are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location.
VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not
covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will
notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for
the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location
CNQPIYKVJCFGUETKRVKQPQHVJGOCNHWPEVKQPQTFKHĹżEWNV[CPF
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model)
and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other
written or oral communications related to this Product. VTech provides no other
warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the
2TQFWEV6JGTGCTGPQQVJGTGZRTGUUYCTTCPVKGU0QQPGKUCWVJQTK\GFVQOCMGOQFKĹżECVKQPUVQVJKUNKOKVGF
YCTTCPV[CPF[QWUJQWNFPQVTGN[QPCP[UWEJOQFKĹżECVKQP
5VCVG2TQXKPEKCN.CY4KIJVU6JKUYCTTCPV[IKXGU[QWURGEKĹżENGICNTKIJVUCPF[QWOC[CNUQJCXGQVJGTTKIJVU
which vary from state to state or province to province.
.KOKVCVKQPU+ORNKGFYCTTCPVKGUKPENWFKPIVJQUGQHĹżVPGUUHQTCRCTVKEWNCTRWTRQUGCPF
OGTEJCPVCDKNKV[ CPWPYTKVVGPYCTTCPV[VJCVVJG2TQFWEVKUĹżVHQTQTFKPCT[WUG CTGNKOKVGFVQQPG[GCTHTQOVJG
date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental,
EQPUGSWGPVKCNQTUKOKNCTFCOCIGU KPENWFKPIDWVPQVNKOKVGFVQNQUVRTQĹżVUQTTGXGPWGKPCDKNKV[VQWUGVJG
Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting
from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under
Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide
reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
%JCPIGUQTOQFKĹżECVKQPUVQVJKUGSWKROGPVPQVGZRTGUUN[CRRTQXGFD[VJGRCTV[TGURQPUKDNGHQTEQORNKCPEG
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Privacy of communications may not be ensured
when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can
be safely absorbed by a user or bystander according to the intended usage of the product. This product has
been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the
user. The telephone base shall be installed and used such that parts of the user’s body other than the hands
are maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the
Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment
EQPVCKPUCOQPIQVJGTVJKPIUCRTQFWEVKFGPVKĹżGTKPVJGHQTOCV75###'36::::6JKUKFGPVKĹżGTOWUVDG
provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply
with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is
also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two
lines. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your
telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th
CPFVJEJCTCEVGTUHQNNQYKPIVJG75KPVJGRTQFWEVKFGPVKĹżGT GIKHKUVJG4'0KU +POQUVDWV
PQVCNNCTGCUVJGUWOQHCNN4'0UUJQWNFDGĹżXG  QTNGUU(QTOQTGKPHQTOCVKQPRNGCUGEQPVCEV[QWT
telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment
connected to your telephone line, ensure the connection of this equipment does not disable your alarm
equipment. If you have questions about what will disable alarm equipment, consult your telephone service
RTQXKFGTQTCSWCNKĹżGFKPUVCNNGT
12
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been
corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized
agents. For repair procedures, follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service provider may temporarily
discontinue your telephone service. The telephone service provider is required to notify you before
KPVGTTWRVKPIUGTXKEG+HCFXCPEGPQVKEGKUPQVRTCEVKECN[QWYKNNDGPQVKĹżGFCUUQQPCURQUUKDNG;QWYKNNDG
given the opportunity to correct the problem and the telephone service provider is required to inform you of
[QWTTKIJVVQĹżNGCEQORNCKPVYKVJVJG(%%;QWTVGNGRJQPGUGTXKEGRTQXKFGTOC[OCMGEJCPIGUKPKVUHCEKNKVKGU
equipment, operation, or procedures that could affect the proper functioning of this product. The telephone
service provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g.,
RQNKEGĹżTGOGFKECN KPVJGUGNQECVKQPU+H[QWFQUVQTGQTVGUVGOGTIGPE[PWODGTURNGCUG
4GOCKPQPVJGNKPGCPFDTKGƀ[GZRNCKPVJGTGCUQPHQTVJGECNNDGHQTGJCPIKPIWR
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference, including interference that may cause undesired operation.
6JGVGTOŎŏ+%ŎŏDGHQTGVJGEGTVKſECVKQPTGIKUVTCVKQPPWODGTQPN[UKIPKſGUVJCVVJG+PFWUVT[%CPCFCVGEJPKECN
URGEKĹżECVKQPUYGTGOGV
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of
the maximum number of devices allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the RENs
QHCNNVJGFGXKEGUFQGUPQVGZEGGFĹżXG
6JKURTQFWEVOGGVUVJGCRRNKECDNG+PFWUVT[%CPCFCVGEJPKECNURGEKĹżECVKQPU
6GEJPKECNURGEKĹżECVKQPU
Frequency control
Crystal controlled PLL synthesizer
Transmit frequency
Handset: 1921.536-1928.448 MHz
Telephone base: 1921.536-1928.448 MHz
Channels
Nominal effective range
Maximum power allowed by FCC and IC. Actual operating range may
vary according to environment conditions at the time of use.
Power requirements
Handset: 2.4V Ni-MH battery
Telephone base: 6V AC @ 300mA
Charger: 6V AC @ 300mA
Memory
Handset directory:
50 memory locations; up to 30 digits and 15 characters
Handset call log:
50 memory locations; up to 24 digits and 15 characters
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc., Beaverton, Oregon 97008.
Distributed in Canada by VTech Technologies Canada Ltd., Richmond, B.C. V6W 1L5.
VTech is the registered trademark of VTech Holdings Limited.
Copyright Š 2011 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
13
User’s manual
CS6529/CS6529-2
DECT 6.0 cordless telephone
Introduction
To protect our environment and conserve natural resources, this user’s manual
provides you with the basic installation and use instructions. A limited set of features
are described in abbreviated form.
Please refer to the complete online user’s manual for a full set of installation and
operation instructions at www.vtechphones.com.
Before using this VTech product, please read Important safety instructions on
page 11 of this user’s manual.
Table of contents
Parts checklist ...................................... 1
Telephone base and charger
installation ........................................ 2
Battery installation ................................ 2
Battery charging ................................... 2
Tabletop to wall mount
installation ........................................ 3
Handset overview ................................. 3
Telephone base overview..................... 4
Using the handset menu....................... 4
Telephone settings ............................... 4
Telephone operation............................. 5
Directory ...............................................6
Speed dial............................................. 7
Caller ID................................................7
About the answering system ................ 8
Answering system settings ................... 8
Answering system operation ................ 8
Add and register a handset .................. 9
Replace a handset................................ 9
Troubleshooting.................................... 9
Important safety instructions................. 11
Precautions for users of implanted
cardiac pacemakers ......................... 12
Operating range.................................... 12
Maintenance ......................................... 12
About cordless telephones ................... 12
ÂŽ
The RBRC seal ................................... 13
Limited warranty ................................... 13
FCC, ACTA and IC regulations ............ 13
6GEJPKECNURGEKĹżECVKQPU........................ 14
Parts checklist
Your telephone package contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
Battery compartment
cover
(1 for CS6529 and
2 for CS6529-2)
Handset
Telephone line cord
Battery
(1 for CS6529,
2 for CS6529-2)
Charger and charger
adapter
Telephone base
(1 for CS6529 and
2 for CS6529-2)
(1 for CS6529-2)
Quick start guide
User’s manual
User’s manual
Quick start guide
Telephone base
power adapter
Wall mount
bracket
Telephone base and charger installation
Install the telephone base and charger as shown below.
Charger adapter
Telephone wall jack
Telephone base
power adapter
#&5.ĹżNVGT PQVKPENWFGF 
is required if you have DSL
high-speed Internet service
Electrical outlet
not controlled by
a wall switch
Electrical outlet
not controlled
by a wall switch
Telephone line cord
Charger
Telephone base
•
•
Use only the power adapter and battery supplied with this product. To order a
replacement, visit our website at www.vtechphones.com or call 1 (800) 595-9511.
In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
6JGRQYGTCFCRVGTKUKPVGPFGFVQDGEQTTGEVN[QTKGPVGFKPCXGTVKECNQTƀQQTOQWPV
position. The prongs are not designed to hold the plug in place if it is plugged into
a ceiling, under-the-table or cabinet outlet.
Battery installation
Install the battery as shown below.
1. Plug the battery connector
securely into the socket.
2. Place the battery with the label
THIS SIDE UP facing up and
the wires inside the battery
compartment.
3. Slide the battery compartment
cover towards the center of the
handset until it clicks into place.
4. Place the handset in the telephone
base or charger to charge.
CHARGE light
remains on
when charging.
If the handset will not be used for a long time, disconnect and remove the battery to
prevent possible leakage.
Battery charging
Once you have installed the battery, the screen indicates the battery status (see
the table below). For best performance, keep the handset in the telephone base or
charger when not in use. The battery is fully charged after 10 hours of continuous
charging. Refer to the online user’s manual for battery operating times.
Battery indicators
Battery status
Action
The screen is blank,
or shows PLACE IN
CHARGER and ƀCUJGU
The battery has no charge or
very little charge. The handset
cannot be used.
Charge without interruption
(at least 30 minutes).
The screen shows
LOW BATTERY and
ƀCUJGU
The battery has enough
charge to be used for a
short time.
Charge without interruption
(at least 30 minutes).
The screen shows
HANDSET X.
The battery is charged.
To keep the battery charged,
place it in the telephone
base or charger when not
in use.
• If you place the handset in the telephone base or charger without plugging in the
battery, the screen displays NO BATTERY.
Tabletop to wall mount installation
The telephone comes ready for tabletop use. Follow the steps below to mount your
telephone on a wall.
1. Plug one end of the telephone line
2. Position the telephone base against
the wall mount bracket as shown.
cord into the TEL LINE jack at the
Insert the extended tabs marked B
bottom of the telephone base and
on the wall mount bracket into the
the base power adapter into the
slots marked B on the back of the
POWER jack.
telephone base. Push the telephone
base down until it clicks securely.
4. Align the holes on the bracket with
the standard wall plate and slide the
bracket down until it locks securely.
Bundle the telephone line cord
and power adapter cord neatly
with twist ties.
3. Route the telephone line cord
through the hole on the wall mount
bracket and plug it into the telephone
wall jack. Route the power cord out
of the telephone base and plug it into
an electrical outlet not controlled by a
wall switch.
Handset overview
CHARGE light
On when the handset is charging.
CID /VOLUME
Review the call log when the phone
is not in use.
Decrease the listening volume
during a call or message playback.
Scroll down while in a menu, or in
the directory, call log or redial list.
Move the cursor to the left when
entering numbers or names.
/VOLUME
Review the directory when the
phone is not in use.
Increase the listening volume
during a call or message
playback.
Scroll up while in a menu, or in
the directory, call log or redial list.
Move the cursor to the right when
entering numbers or names.
MENU/SELECT
Show the menu.
While in a menu, press to select
an item, or save an entry or
setting.
REDIAL/PAUSE
Press repeatedly to review the
redial list.
Press and hold to insert a dialing
pause while entering numbers.
OFF/CANCEL
Hang up a call.
Silence the ringer temporarily while
the handset is ringing.
Press and hold to erase the missed
call indicator while the phone is not
in use.
Press to return to the previous
menu, or press and hold to return
to idle mode, without making
changes.
/FLASH
Make or answer a call.
Answer another incoming call
during a call.
Press repeatedly to add or
remove 1 in front of the call log
entry before dialing or saving it to
the directory.
# (pound key)
Press repeatedly to show other
dialing options when reviewing a
call log entry.
Dialing keys
Enter numbers or characters.
INT (intercom)
Start an intercom conversation or
transfer a call (for multi-handset
models only).
TONE
Switch to tone dialing
temporarily during a call.
MUTE/DELETE
Mute the microphone during a call.
Delete digits or characters while
using the dialling keys.
Silence the ringer temporarily while
the handset is ringing.
Delete the displayed entry while in
the directory, call log or redial list.
(speakerphone)
Make or answer a call using the
handset speakerphone.
During a call, press to switch
between the speakerphone and the
handset.
Telephone base overview
Message window
/REPEAT
Shows the number of messages and other answering
system information.
Press to repeat a
message or press twice
to play the previous
message.
X/DELETE
Delete the playing message.
Press twice to delete all
previously reviewed messages
when the phone is not in use.
IN USE light
Flashes when there is an
incoming call, or another
telephone sharing the
same line is in use.
On when the handset is
in use, or the answering
system is answering a call.
/SKIP
Skip to the next message.
/PLAY/STOP
Play or stop playing
messages.
/FIND HANDSET
/VOL and
Press once and then
release to page all system
handsets.
/VOL
Adjust the volume during
message playback.
Adjust the telephone base
ringer volume when the phone
is not in use.
/ANS ON/OFF
Turn the answering
system on or off.
Using the handset menu
1.
2.
3.
•
•
Press MENU when the phone is not in use.
Press or until the screen displays the desired feature menu.
Press SELECT to enter that menu.
To return to the previous menu, press CANCEL.
To return to idle mode, press and hold CANCEL.
Telephone settings
Default settings are indicated by an asterisk(*).
Screen display
Function
Options
LCD LANGUAGE
Set the screen display language.
ENGLISH*
FRANÇAIS
ESPAÑOL
CLR VOICEMAIL
Turn off the voicemail indicators.
TURN OFF
INDICATOR?
KEY TONE
Turn an audible beep on or off whenever a key
is pressed.
ON*
OFF
SET DATE/TIME
Set the date and time shown on
the handset.
-:-- --/--
HOME AREA CODE
Enter your home area code if you dial only seven
digits for local calls.
___
DIAL MODE
Set the telephone to be tone or
pulse dialing.
TONE*
PULSE
The following are some of the telephone features you may wish to set. Refer to
Telephone settings in the online user’s manual for detailed instructions on setting
all telephone features.
Ringer volume (handset)
You can adjust the ringer volume level, or turn the ringer off.
1. Press MENU when the handset is not in use.
2. Scroll to >RINGERS then press SELECT twice.
3. Press or to adjust the volume, then press SELECT to save.
•
•
If the handset ringer volume is set to off, that handset is silenced for all incoming
calls except paging tone.
The ringer volume also determines the ringer volume of the intercom calls and the
volume of the paging tone.
Set date and time
If you subscribe to caller ID service, the day, month and time are set automatically
with each incoming call. You can also set the date and time manually.
1. Press MENU when the handset is not in use.
2. Scroll to select >SETTINGS, then press SELECT.
3. Scroll to select >SET DATE/TIME, then press SELECT.
4. Use the dialing keys (0-9) to enter the month, date and year, then press SELECT.
5. Use the dialing keys (0-9) to enter the hour and minute.
6. Press or to choose AM or PM, or press 2 for AM or 7 for PM. Press
SELECT to save.
Voicemail indicators
If you subscribe to voicemail service offered by your telephone service provider,
NEW VOICEMAIL and
appear on the handset when you have new voicemail
messages. Contact your telephone service provider for more information and
assistance about using your voicemail service. Refer to Clear voicemail indicators
in the online user’s manual on how to clear the voicemail indicators.
Telephone operation
Make a call
•
Press
or
then dial the telephone number.
Answer a call
•
Press
or any dialing key.
End a call
•
Press OFF or put the handset to the telephone base or charger.
Speakerphone
•
During a call, press
handset use.
to switch between speakerphone and normal
Volume
•
During a call, press
/VOLUME or
/VOLUME to adjust the listening volume.
The handset earpiece volume setting and speakerphone volume setting are
independent.
Mute
The mute function allows you to hear the other party but the
other party cannot hear you.
1. During a call, press MUTE. The handset displays MUTE.
2. Press MUTE again to resume the conversation.
Call waiting
When you subscribe to call waiting service from your telephone service provider,
you hear an alert tone if there is an incoming call while you are on another call.
• Press FLASH to put the current call on hold and take the new call.
• Press FLASH at any time to switch back and forth between calls.
Temporary ringer silencing
When the telephone is ringing, you can temporarily silence the ringer of the handset
without disconnecting the call. The next call rings normally at the preset volume.
• To silence the handset ringer, press OFF or MUTE on the handset.
RINGER MUTED and
display.
Temporary tone dialing
If you have pulse (rotary) service only, you can switch from pulse
to tone dialing temporarily during a call.
1. During a call, press TONE .
2. Use the dialing keys to enter the relevant number. The
telephone sends touch-tone signals.
3. The telephone automatically returns to pulse dialing mode
after you end the call.
Find handset
7UGVJKUHGCVWTGVQĹżPFCNNU[UVGOJCPFUGVU
To start paging:
• Press /FIND HANDSET on the telephone base once and
then release. All idle handsets ring and their screens
show ** PAGING **.
To end paging:
• Press /FIND HANDSET again on the telephone base once and then release.
or any dialing key on the handset.
• Press
• Place the handset in the telephone base or charger.
Do not press and hold /FIND HANDSET for more than four seconds. It may lead
to handset deregistration.
Redial list
Each handset stores the last 10 telephone numbers dialed.
To review and dial a number from the redial list:
1. Press REDIAL when the handset is not in use.
2. Press , , or REDIAL repeatedly until the desired
entry displays.
to dial.
3. Press
To delete a redial entry:
When the desired redial entry displays, press DELETE.
Chain dialing
Use this feature to initiate a dialing sequence from numbers stored in the directory,
call log or redial list while you are on a call. Chain dialing can be useful if you wish
to access other numbers (such as bank account numbers or access codes) from the
directory, call log or redial list.
To access a number in the directory, call log or redial list while on a call:
1. To enter the directory, press MENU, then scroll to >DIRECTORY, and then
press SELECT.
-ORTo enter the call log, press MENU, then scroll to >CALL LOG, and then
press SELECT.
-ORTo enter the redial list, press REDIAL.
2. Press or to scroll to the desired entry.
3. Press SELECT to dial the displayed number.
Join a call in progress
You can use up to four system handsets at a time on an outside call. You can buy
additional expansion handsets (CS6409) for this telephone base. You can register
WRVQĹżXGJCPFUGVUVQVJGVGNGRJQPGDCUG
or
on another handset to join the call.
• When a handset is on a call, press
• Press OFF to exit the call. The call continues until all handsets hang up.
Intercom
Use the intercom features for conversations between two handsets.
1. Press INT on your handset when not in use. When you have three or more
handsets, use the dialing keys to enter a destination handset number.
, , INT or any dialing key on the
2. To answer the intercom call, press
destination handset.
3. To end an intercom call, press OFF or place the handset back in the telephone
base or charger.
Answer an incoming call during an intercom call
If you receive an outside call during an intercom call, there is an alert tone.
. The intercom call ends automatically.
• To answer the outside call, press
• To end the intercom call without answering the outside call, press OFF. The
intercom call ends and the telephone continues to ring.
Call transfer using intercom
Use the intercom feature to transfer an outside call to another system handset.
1. During a call, press INT. When you have three or more handsets, use the
dialing keys to enter a destination handset number.
, , INT or any dialing key on the
2. To answer the intercom call, press
destination handset. The outside call is now on hold and both handsets show
INTERCOM. You can have a private conversation with the destination handset.
3. From this intercom call, you have the following options:
• You can let the destination handset join you on the outside call in a three-way
conversation. Press and hold INT on the original handset.
• You can transfer the call. Press OFF, or place your handset back
in the telephone base or charger. Your handset screen shows
CALL TRANSFERRED. The destination handset then automatically
connects to the outside call.
• You can press INT to switch between the outside call (OUTSIDE CALL
displays) and the intercom call (INTERCOM displays).
• The destination handset can end the intercom call by pressing OFF, or by
placing the handset back in the telephone base or charger. The outside call
continues with the original system handset.
Directory
The directory can store up to 50 entries and are shared by all system handsets.
To add a directory entry:
1. Press MENU/SELECT twice.
2. Scroll to >ADD CONTACT then press SELECT.
• Use the dialing keys to enter the number (up to 30 digits).
-OR• Copy a number from the redial list by pressing REDIAL and then press ,
or REDIAL repeatedly to select a number. Press SELECT.
3. Press SELECT to move to the name.
4. Use the dialing keys to enter the name (up to 15 characters). Additional key presses
show other characters of that particular key.
5. Press SELECT to save.
While entering names and numbers, you can:
• Press DELETE to backspace and erase a digit or character.
• Press and hold DELETE to erase the entire entry.
• Press and hold PAUSE to insert a dialing pause (for entering phone numbers only).
• Press or to move the cursor to the left or right.
• Press 0 to add a space (for entering names only).
To review and dial from the directory:
Entries are sorted alphabetically.
1. Press
when the handset is not in use.
2. Scroll to browse through the directory, or use the dialing keys to start a
name search.
3. When the desired entry appears, press
or
to dial.
To edit a directory entry:
1. When the desired entry displays, press SELECT.
2. Use the dialing keys to edit the number, then press SELECT.
3. Use the dialing keys to edit the name, then press SELECT to save.
To delete a directory entry:
1. When the desired entry displays, press DELETE.
2. When the screen displays DELETE CONTACT?, press SELECT.
Speed dial
You can copy up to 10 directory entries into the speed dial locations so that you can
dial these numbers using fewer keys than usual.
To store a speed dial entry:
1. Press MENU/SELECT twice when the handset is not in use.
2. Scroll to >SPEED DIAL, then press SELECT.
3. Scroll to a desired speed dial location, then press SELECT.
4. Scroll to a desired directory entry, then press SELECT to save.
To dial a speed dial entry:
1. Press and hold a dialing key (0-9) to display the desired speed dial entry when
the handset is not in use.
2. Press
or
to dial the displayed phone number.
To delete a speed dial entry:
When the desired entry displays, press DELETE.
Caller ID
This product supports caller ID services provided by most telephone service
providers. Depending on your service subscription, you may see the caller’s name,
number, date and time of calls that are sent by your telephone service provider after
VJGĹżTUVQTUGEQPFTKPI
Call log
The call log stores up to 50 entries. If you answer a call before the caller information
appears, it will not be saved in the call log.
• The handset displays XX MISSED CALLS when there are calls that have not
been reviewed in the call log.
• If you want to erase the missed call indicator, press and hold CANCEL on the
idle handset.
To review and dial a number in the call log:
1. Press CID when the handset is not in use.
2. Scroll to browse through the call log. When the desired entry appears:
• Press # (pound key) repeatedly to show different dialing options.
• Press 1 repeatedly if you need to add or remove 1 in front of the
phone number.
3. Press
to dial the displayed number.
To save a call log entry to the directory:
1. When the desired call log entry displays, press SELECT.
2. Use the dialing keys to modify the number, then press SELECT.
3. Use the dialing keys to modify the name, then press SELECT to save.
To delete one call log entry:
• When the desired call log entry displays, press DELETE.
To delete all call log entries:
• Press MENU when the handset is not in use. Scroll to >CALL LOG and then
press SELECT. Scroll to >DEL ALL CALLS and then press SELECT twice.
About the answering system
The answering system can record up to 99 messages, depending on the length of
each message. The total recording time is approximately 14 minutes.
Answering system settings
Default settings are indicated by asterisks (*).
Screen display
Function
Options
CALL SCREENING
Set whether you hear the callers while they are
leaving messages to you.
ON*
OFF
# OF RINGS
Set the number of times the telephone rings before
the answering system answers.
6; 5; 4; 3*; 2;
TOLL SAVER
REMOTE CODE
Set a two-digit security code to access the
answering system remotely from any touch-tone
telephone.
19*
MSG ALERT TONE
Set to alert you when you have new messages.
ON
OFF*
RECORDING TIME
Set the recording time for each incoming message. 3 MINUTES*
2 MINUTES
1 MINUTE
Number of rings
You can set the answering system to answer an incoming call after 2, 3, 4, 5 or 6
rings; or toll saver. If you choose toll saver, the answering system answers a call
after 2 rings when you have new messages, or after 4 rings when you have no new
messages.
1. Press MENU when the handset is not in use.
2. Scroll to >ANSWERING SYS then press SELECT.
3. Scroll to >ANS SYS SETUP then press SELECT.
4. Scroll to ># OF RINGS then press SELECT.
5. Press or to choose 2, 3, 4, 5, 6 or TOLL SAVER and then press SELECT.
Answering system operation
Turn the answering system on or off
The answering system must be turned on to answer and record messages.
• Press /ANS ON/OFF on the telephone base to turn the built-in answering
system on or off.
Record your own announcement with a handset
You can use the preset announcement to answer calls, or replace it with your own
recorded announcement. It can be up to 90 seconds in length.
1. Press MENU when the handset is not in use.
2. Scroll to >ANSWERING SYS and then press SELECT twice.
3. The handset announces, “To play, press 2. To record, press 7.” Press 7 to record.
4. The handset announces, “Record after the tone. Press 5 when you are done.”
After the tone, speak towards the handset microphone. Press 5 when done.
5. The answering system automatically plays back the newly recorded announcement.
Press 5 to stop the playback at any time; 2 to replay the recorded announcement;
3 to delete the recorded announcement; or 7 to record again if desired.
Message playback at the telephone base
Press
/PLAY/STOP when the phone is not in use.
Options during playback:
• Press VOL or VOL to adjust the speaker volume.
• Press /SKIP to skip to the next message.
• Press /REPEAT to repeat the message currently playing. Press /REPEAT
twice to listen to the previous message.
• Press X/DELETE to delete the playing message. The system advances to the
next message.
• Press
/PLAY/STOP to stop.
Delete all messages at the telephone base
Press X/DELETE twice when the phone is not in use.
Call screening at the telephone base
If the answering system and call screening are on, the announcement and the
incoming message broadcast at the telephone base when a call is answered by the
answering system.
Options while recording a message:
• Press VOL or VOL on the telephone base to adjust the call screening volume.
• Press /PLAY/STOP to temporarily turn on or off call screening.
• Press VOL to temporarily turn on call screening when it is set to off.
Call intercept
If you want to talk to the person whose message is being recorded, press
on the handset.
or
Access the answering system remotely
1. Dial your telephone number from any touch-tone telephone.
2. When the system plays your announcement, enter the two-digit remote code.
The preset code is 19.
3. You can enter one of the following remote commands.
Command
Function
Play all messages.
Play new messages.
Delete a message (during playback).
33
Delete all old messages.
Repeat the current message (during playback).
Stop.
*5
Hear a list of remote commands.
Skip to the next message (during playback).
*7
Record an announcement.
End the call.
Turn the answering system on or off.
4. Hang up or press 8 to end the call.
Add and register a handset
The handsets provided with your telephone system are already registered. Each
handset is assigned a number that displays on the handset. Additional handsets
registered to the telephone system are assigned numbers in the sequential order.
6JKUVGNGRJQPGU[UVGOCEEQOOQFCVGUWRVQĹżXGJCPFUGVU
You can add new handsets (CS6409, purchased separately) to your telephone
system. Each handset must be registered with the telephone base before use.
9JGPĹżTUVRWTEJCUGFCPFRTQRGTN[EJCTIGFGCEJGZRCPUKQPJCPFUGVUJQYU
1.PRESS FIND HS ON BASE 4 SEC and 2.THEN PRESS # ON HANDSET
alternately. Charge the handset before registering it to the telephone base.
To register a handset:
1. Place the non-registered handset in the telephone base or charger.
2. On the telephone base, press and hold /FIND HANDSET for about
four seconds until the red IN USE light turns on.
3. On the handset, press # (pound key) then the handset shows REGISTERING.....
PLEASE WAIT. Then the handset shows HANDSET REGISTERED and you
hear a beep when the registration process completes. The registration process
takes about 60 seconds to complete.
Replace a handset
If you want to replace a handset or reassign the designated handset number of a
registered handset, you must deregister all handsets and then individually register
each handset.
To deregister all handsets:
1. Press and hold /FIND HANDSET on the telephone base for about 10 seconds
until the IN USENKIJVQPVJGVGNGRJQPGDCUGVWTPUQPCPFUVCTVUƀCUJKPI
2. Press and release /FIND HANDSET again. You must press /FIND HANDSET
while the IN USENKIJVKUUVKNNƀCUJKPI6JGIN USENKIJVƀCUJGUHQTCRRTQZKOCVGN[
ĹżXGUGEQPFU
3. All handsets show 1.PRESS FIND HS ON BASE 4 SEC and
2.THEN PRESS # ON HANDSET alternately when the deregistration process
completes. The deregistration process takes about 10 seconds to complete.
Troubleshooting
+H[QWJCXGFKHĹżEWNV[YKVJ[QWTVGNGRJQPGRNGCUGVT[VJGUWIIGUVKQPUDGNQY(QTEWUVQOGT
service, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada,
go to www.vtechcanada.com or call 1 (800) 267-7377.
My telephone does not work at all.
• Make sure the battery is installed and charged correctly. For optimum daily performance,
return the handset to the telephone base or charger after use.
• Make sure the power adapter is securely plugged into an outlet not controlled by a wall switch.
• /CMGUWTGVJGVGNGRJQPGNKPGEQTFKURNWIIGFſTON[KPVQVJGVGNGRJQPGDCUGCPFVJGYCNNLCEM
• Unplug the electrical power to the telephone base. Wait for approximately 15 seconds,
then plug it back in. Allow up to one minute for the cordless handset and telephone base to
synchronize.
• Charge the battery in the handset for up to 10 hours.
• If the battery is completely depleted, it may take up to 30 minutes to charge the handset
before LOW BATTERY appears on the screen.
• Remove and install the battery again. If that still does not work, it may be necessary to
purchase a new battery.
• Disconnect the telephone base from the telephone wall jack and plug in a working
telephone. If the other telephone does not work, the problem is probably in the wiring or
telephone service. Contact your telephone service provider.
There is no dial tone.
•
•
•
•
Try all the above suggestions.
Move the handset closer to the telephone base. It may be out of range.
The telephone line cord may be defective. Install a new telephone line cord.
Disconnect the telephone base from the telephone wall jack and connect a different telephone.
If there is no dial tone on this telephone either, the problem is in your wiring or telephone
service. Contact your telephone service provider.
I cannot dial out.
• Try all the above suggestions.
• Make sure there is a dial tone before dialing. It is normal if the handset takes a second or
two to synchronize with the telephone base before producing a dial tone. Wait an extra
second before dialing.
• If other telephones in your home are having the same problem, the problem is in the wiring
or telephone service. Contact your telephone service provider (charges may apply).
• Eliminate any background noise. Mute the cordless handset before dialing, or dial from
another room in your home with less background noise.
The handset shows 1.PRESS FIND HS ON BASE 4 SEC and 2.THEN PRESS #
ON HANDSET alternately and it does not work at all.
• The handset may be deregistered from the telephone base. Refer to Add and register a
handset on page 9 to register the handset to the telephone base.
LOW BATTERY shows on the handset screen.
• Place the handset in the telephone base or charger for recharging.
• Remove and install the battery again and use it until fully depleted, then charge the handset
in the telephone base or charger for up to 10 hours.
• If the above measures do not correct the problem, replace the battery.
The battery does not charge in the handset or the handset battery does not
accept charge.
• Make sure the handset is placed in the telephone base or charger correctly. The CHARGE
light on the handset should be on.
• Remove and install the battery again, then charge for up to 10 hours.
• If the handset is in the telephone base but the CHARGE light on the handset is not on, refer
to The CHARGE light is off below.
• If the battery is completely depleted, charge the handset for at least 30 minutes before use.
• Purchase a new battery. Refer to Battery installation on page 2.
The telephone does not ring when there is an incoming call.
• Make sure the handset ringer volume is not set to off and the telephone base ringer volume
is not set to zero.
• Make sure the telephone line cord and power adapter are plugged in properly.
• The handset may be too far from the telephone base. Move it closer to the telephone base.
• There may be too many extension phones on the telephone line to allow all of them to ring
simultaneously. Unplug some of them.
• If other telephones in your home are having the same problem, the problem is in the wiring
or telephone service. Contact your telephone service provider (charges may apply).
• Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible from
these types of electronic devices.
• Test a working telephone at the telephone wall jack. If another telephone has the same
problem, the problem is in the telephone wall jack. Contact your telephone service provider
(charges may apply).
• The telephone line cord may be defective. Install a new telephone line cord.
• Remove and install the battery again and then place the handset in the telephone base.
• Wait for the handset to synchronize with the telephone base. Allow up to one minute for this
to take place.
My caller ID features are not working properly.
• Caller ID is a subscription service. You must subscribe to this service from your telephone
service provider for this feature to work on your telephone.
• The caller may not be calling from an area which supports caller ID.
• Both your and your caller’s telephone service providers must use equipment compatible with
the caller ID service.
• 6JGECNNGT+&KPHQTOCVKQPUJQYUCHVGTVJGſTUVQTUGEQPFTKPI
• If you subscribe to high-speed Internet service (DSL - digital subscribe line) through
[QWTVGNGRJQPGNKPG[QWOWUVKPUVCNNC&5.ĹżNVGTDGVYGGPVJGVGNGRJQPGline cord and
VJGVGNGRJQPGYCNNLCEM6JGĹżNVGTRTGXGPVUPQKUGCPFECNNGT+&RTQDNGOUECWUGFD[&5.
KPVGTHGTGPEG%QPVCEV[QWT&5.UGTXKEGRTQXKFGTHQTOQTGKPHQTOCVKQPCDQWV&5.ĹżNVGTU
My handset beeps and is not performing normally.
• Make sure the power cord is securely plugged into the telephone base. Plug the telephone
base into a different working electrical outlet not controlled by a wall switch.
• Move the handset closer to the telephone base. It may be out of range.
• Reset the telephone base by unplugging the electrical power to the base. Wait for 15 seconds
and plug it back in again. Allow up to one minute for the cordless handset and the telephone
base to synchronize.
• Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible
from these types of electronic devices.
There is interference during a telephone conversation.
My calls fade out when I am using the cordless handset.
• The handset may be out of range. Move it closer to the telephone base.
• If you subscribe to high-speed Internet service (DSL - digital subscriber line) through
[QWTVGNGRJQPGNKPG[QWOWUVKPUVCNNC&5.ĹżNVGTDGVYGGPVJGVGNGRJQPGNKPGEQTFCPF
VJGVGNGRJQPGYCNNLCEM6JGĹżNVGTRTGXGPVUPQKUGCPFECNNGT+&RTQDNGOUECWUGFD[&5.
KPVGTHGTGPEG%QPVCEV[QWT&5.UGTXKEGRTQXKFGTHQTOQTGKPHQTOCVKQPCDQWV&5.ĹżNVGTU
10
• Appliances or other cordless telephones plugged into the same circuit as the telephone base
can cause interference. Try moving the appliance or telephone base to another outlet.
• Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as
possible from these types of electronic devices.
• If your telephone is plugged in with a modem or a surge protector, plug the telephone (or
modem/surge protector) into a different location. If this doesn’t solve the problem, relocate
your telephone or modem farther apart from each other, or use a different surge protector.
• The location of your telephone base can impact the performance of your cordless phone. For
DGVVGTTGEGRVKQPKPUVCNNVJGVGNGRJQPGDCUGKPCEGPVTCNK\GFNQECVKQPYKVJKP[QWTJQOGQTQHĹżEG
away from walls or other obstructions. In many environments, elevating the telephone base
improves overall performance.
• Disconnect the telephone base from the telephone wall jack and plug in a corded telephone. If
calls are still not clear, the problem is probably in the wiring or telephone service. Contact your
telephone service provider (charges may apply).
• If other telephones in your home are having the same problem, the problem is in the wiring or
telephone service. Contact your telephone service provider (charges may apply).
The handset shows OUT OF RANGE OR NO PWR AT BASE.
• The handset may be out of range. Move it closer to the telephone base.
• Make sure the power cord is securely plugged into the telephone base. Use a working
electrical outlet not controlled by a wall switch.
• Reset your telephone by unplugging the power adapter from the telephone base. Disconnect
the battery from the cordless handset. Wait for 15 seconds, then plug in the power adapter
and reinstall the battery. Place the handset in the telephone base and allow up to one minute
for the handset and telephone base to synchronize.
• Other electronic products such as HAM radios and other DECT phones can cause
interference with your cordless phone. Try installing your phone as far away as possible
from these types of electronic devices.
NEW VOICEMAIL and
show on the display and I don’t know why.
appear on the display, then your telephone has received a
• If NEW VOICEMAIL and
signal from your telephone service provider that you have a voicemail message waiting
for you to retrieve from your telephone service provider. Contact your telephone service
provider for more information on how to access your voicemail.
The answering system does not answer after correct number of rings.
• Make sure the answering system is on. When the answering system is on, ANS ON should
show on the handset and the /ANSWER ON/OFF light is lit on the telephone base.
• If toll saver is selected, the number of rings changes to two when there are new messages.
• If the memory is full or the answering system is off, the answering system answers after 10
rings. In some cases, the answering system is affected by the ringing system used by the
telephone service provider.
• If you subscribe to voicemail service, change the number of rings so that your answering
system answers before your voicemail answers. To get help with your voicemail settings,
contact your telephone service provider.
• If there is a fax machine connected to the same telephone line, try disconnecting the fax
machine. If that solves the problem, consult your fax machine documentation for information
on compatibility with answering systems.
The answering system does not record messages.
• Make sure the answering system is on.
• Make sure the memory of the answering system is not full. When the answering machine
memory is full, it does not record new messages until some old messages are deleted.
• If you subscribe to voicemail service, change the number of ring so that your answering
system answers before your voicemail answers. To determine how many rings activate your
voicemail, contact your telephone service provider.
• If there is a fax machine connected to the same telephone line, try disconnecting the fax
machine. If that solves the problem, consult your fax machine documentation for information
on compatibility with answering systems.
The messages on the answering system are incomplete.
• If a caller leaves a very long message, part of it may be lost when the answering system
disconnects the call after the preset recording time.
• If the memory on the answering system becomes full during a message, the answering
system stops recording and disconnects the call.
• If the caller’s voice is very soft, the answering system may stop recording and disconnect
the call.
Common cure for electronic equipment.
• If the telephone is not responding normally, put the cordless handset in the telephone base.
If this does PQVĹżZVJGRTQDNGO, do the following (in the order listed):
1. Disconnect the power to the telephone base.
2. Disconnect the battery on the cordless handset.
3. Wait a few minutes before connecting power to the telephone base.
4. Install the battery again and place the cordless handset in the telephone base .
5. Wait for the cordless handset to synchronize with the telephone base. Allow up one
minute for this to take place.
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk
QHĹżTGGNGEVTKEUJQEMCPFKPLWT[KPENWFKPIVJGHQNNQYKPI
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
4. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To
protect them from overheating, these openings must not be blocked by placing the product on a soft surface
such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This
product should not be placed in any area where proper ventilation is not provided.
7. This product should be operated only from the type of power source indicated on the marking label. If you are
PQVUWTGQHVJGV[RGQHRQYGTUWRRN[KP[QWTJQOGQTQHĹżEGEQPUWNV[QWTFGCNGTQTNQECNRQYGTEQORCP[
11
8. Do not allow anything to rest on the power cord. Do not install this product where the cord may be
walked on.
9. Never push objects of any kind into this product through the slots in the telephone base or handset
because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind
on the product.
10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized
UGTXKEGHCEKNKV[1RGPKPIQTTGOQXKPIRCTVUQHVJGVGNGRJQPGDCUGQTJCPFUGVQVJGTVJCPURGEKĹżGF
access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause
electric shock when the product is subsequently used.
11. Do not overload wall outlets and extension cords.
12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the
following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operation instructions. Improper adjustment of other controls may
result in damage and often requires extensive work by an authorized technician to restore the product
to normal operation.
E. If the product has been dropped and the telephone base and/or handset has been damaged.
F. If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of
electric shock from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances,
a spark may be created when the adapter is plugged into the power outlet, or when the handset is
replaced in its cradle. This is a common event associated with the closing of any electrical circuit.
The user should not plug the phone into a power outlet, and should not put a charged handset into
VJGETCFNGKHVJGRJQPGKUNQECVGFKPCPGPXKTQPOGPVEQPVCKPKPIEQPEGPVTCVKQPUQHƀCOOCDNG or
ƀCOGUWRRQTVKPIICUGUWPNGUUVJGTGKUCFGSWCVGXGPVKNCVKQP#URCTMKPUWEJCPGPXKTQPOGPV could
ETGCVGCĹżTGQTGZRNQUKQP5WEJGPXKTQPOGPVUOKIJVKPENWFGOGFKECNWUGQHQZ[IGPYKVJQWV adequate
ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.
15. Only put the handset of your telephone next to your ear when it is in normal talk mode.
16. 6JGRQYGTCFCRVGTUCTGKPVGPFGFVQDGEQTTGEVN[QTKGPVGFKPCXGTVKECNQTƀQQTOQWPVRQUKVKQP6JG
prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or
cabinet outlet.
SAVE THESE INSTRUCTIONS
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation
of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six inches from the pacemaker.
• Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is
turned ON.
• Should use the wireless telephone at the ear opposite the pacemaker. WTR’s evaluation did not identify
any risk to bystanders with pacemakers from other persons using wireless telephones.
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications
Commission (FCC). Even so, this handset and telephone base can communicate over only a certain distance
- which can vary with the locations of the telephone base and handset, the weather, and the layout of your home
QTQHĹżEG
When the handset is out of range, the handset displays OUT OF RANGE OR NO PWR AT BASE.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect
well when you press
. Move closer to the telephone base, then press
to answer the call.
If the handset moves out of range during a telephone conversation, there may be interference. To improve
reception, move closer to the telephone base.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you ever need
to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with
wet hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety,
take caution when using electrical appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft
cloth slightly dampened with water or mild soap. Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or standing
in the water. If the telephone base should fall into the water, DO NOT RETRIEVE IT UNTIL YOU
UNPLUG THE POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the
telephone by the unplugged cords.
About cordless telephones
• Privacy: The same features that make a cordless telephone convenient create some
limitations. Telephone calls are transmitted between the telephone base and the cordless handset by radio
waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio
receiving equipment within range of the cordless handset. For this reason, you should not think of cordless
telephone conversations as being as private as those on corded telephones.
• Electrical power: The telephone base of this cordless telephone must be connected to a working electrical
outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the
cordless handset if the telephone base is unplugged, switched off or if the electrical power is interrupted.
• Potential TV interference: Some cordless telephones operate at frequencies that may cause interference
to televisions and VCRs. To minimize or prevent such interference, do not place the telephone base of
the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless
telephone farther away from the TV or VCR often reduces or eliminates the interference.
• Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with
conducting material such as rings, bracelets, and keys. The battery or conductor may overheat and cause
harm. Observe proper polarity between the battery and the battery charger.
• Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn
or puncture the battery. Like other batteries of this type, if burned or punctured, they could release caustic
material which could cause injury.
12
The RBRCÂŽ seal
The RBRCÂŽ seal on the nickel-metal hydride battery indicates that VTech Communications,
Inc. is voluntarily participating in an industry program to collect and recycle these batteries at
the end of their useful lives, when taken out of service within the United States and Canada.
The RBRCÂŽ program provides a convenient alternative to placing used nickel-metal hydride
batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local
retailers participating in the RBRCÂŽ program or at authorized VTech product service centers.
Please call 1 (800) 8 BATTERYTM for information on Ni-MH battery recycling and disposal bans/restrictions
in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and
conserving natural resources.
RBRCÂŽ is a registered trademark of Rechargeable Battery Recycling Corporation.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or
“you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects
in material and workmanship, pursuant to the following terms and conditions, when installed and used
normally and in accordance with the Product operating instructions. This limited warranty extends only to the
Consumer for Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the
limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at
VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new
or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or
refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the
repaired or replacement Products to you in working condition. You should expect the repair or replacement to
take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs
or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies
to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement
Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper
KPUVCNNCVKQPCDPQTOCNQRGTCVKQPQTJCPFNKPIPGINGEVKPWPFCVKQPĹżTGYCVGTQTQVJGTNKSWKFKPVTWUKQPQT
 2TQFWEVVJCVJCUDGGPFCOCIGFFWGVQTGRCKTCNVGTCVKQPQTOQFKĹżECVKQPD[CP[QPGQVJGTVJCPCP
authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or
cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have
been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or
Canada, or used for commercial or institutional purposes (including but not limited to Products used for
rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems
outside the unit.
How do you get warranty service?
To obtain warranty service, please visit our website at www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and
are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location.
VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not
covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will
notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for
the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location
CNQPIYKVJCFGUETKRVKQPQHVJGOCNHWPEVKQPQTFKHĹżEWNV[CPF
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model)
and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other
written or oral communications related to this Product. VTech provides no other
warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the
2TQFWEV6JGTGCTGPQQVJGTGZRTGUUYCTTCPVKGU0QQPGKUCWVJQTK\GFVQOCMGOQFKĹżECVKQPUVQVJKUNKOKVGF
YCTTCPV[CPF[QWUJQWNFPQVTGN[QPCP[UWEJOQFKĹżECVKQP
5VCVG2TQXKPEKCN.CY4KIJVU6JKUYCTTCPV[IKXGU[QWURGEKĹżENGICNTKIJVUCPF[QWOC[CNUQJCXGQVJGTTKIJVU
which vary from state to state or province to province.
.KOKVCVKQPU+ORNKGFYCTTCPVKGUKPENWFKPIVJQUGQHĹżVPGUUHQTCRCTVKEWNCTRWTRQUGCPF
OGTEJCPVCDKNKV[ CPWPYTKVVGPYCTTCPV[VJCVVJG2TQFWEVKUĹżVHQTQTFKPCT[WUG CTGNKOKVGFVQQPG[GCTHTQO
the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special,
KPEKFGPVCNEQPUGSWGPVKCNQTUKOKNCTFCOCIGU KPENWFKPIDWVPQVNKOKVGFVQNQUVRTQĹżVUQTTGXGPWGKPCDKNKV[VQ
use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties)
resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device
under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended
to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
13
%JCPIGUQTOQFKĹżECVKQPUVQVJKUGSWKROGPVPQVGZRTGUUN[CRRTQXGFD[VJGRCTV[TGURQPUKDNGHQTEQORNKCPEG
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Privacy of communications may not be ensured
when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can
be safely absorbed by a user or bystander according to the intended usage of the product. This product has
been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the
user. The telephone base shall be installed and used such that parts of the user’s body other than the hands
are maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the
Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment
EQPVCKPUCOQPIQVJGTVJKPIUCRTQFWEVKFGPVKĹżGTKPVJGHQTOCV75###'36::::6JKUKFGPVKĹżGTOWUVDG
provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply
with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is
also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two
lines. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your
telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th
CPFVJEJCTCEVGTUHQNNQYKPIVJG75KPVJGRTQFWEVKFGPVKĹżGT GIKHKUVJG4'0KU +POQUVDWV
PQVCNNCTGCUVJGUWOQHCNN4'0UUJQWNFDGĹżXG  QTNGUU(QTOQTGKPHQTOCVKQPRNGCUGEQPVCEV[QWT
telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment
connected to your telephone line, ensure the connection of this equipment does not disable your alarm
equipment. If you have questions about what will disable alarm equipment, consult your telephone service
RTQXKFGTQTCSWCNKĹżGFKPUVCNNGT
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been
corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized
agents. For repair procedures, follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service provider may temporarily
discontinue your telephone service. The telephone service provider is required to notify you before
KPVGTTWRVKPIUGTXKEG+HCFXCPEGPQVKEGKUPQVRTCEVKECN[QWYKNNDGPQVKĹżGFCUUQQPCURQUUKDNG;QWYKNNDG
given the opportunity to correct the problem and the telephone service provider is required to inform you of
[QWTTKIJVVQĹżNGCEQORNCKPVYKVJVJG(%%;QWTVGNGRJQPGUGTXKEGRTQXKFGTOC[OCMGEJCPIGUKPKVUHCEKNKVKGU
equipment, operation, or procedures that could affect the proper functioning of this product. The telephone
service provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g.,
RQNKEGĹżTGOGFKECN KPVJGUGNQECVKQPU+H[QWFQUVQTGQTVGUVGOGTIGPE[PWODGTURNGCUG
4GOCKPQPVJGNKPGCPFDTKGƀ[GZRNCKPVJGTGCUQPHQTVJGECNNDGHQTGJCPIKPIWR
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference, including interference that may cause undesired operation.
6JGVGTOŎŏ+%ŎŏDGHQTGVJGEGTVKſECVKQPTGIKUVTCVKQPPWODGTQPN[UKIPKſGUVJCVVJG+PFWUVT[%CPCFCVGEJPKECN
URGEKĹżECVKQPUYGTGOGV
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of
the maximum number of devices allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the RENs
QHCNNVJGFGXKEGUFQGUPQVGZEGGFĹżXG
6JKURTQFWEVOGGVUVJGCRRNKECDNG+PFWUVT[%CPCFCVGEJPKECNURGEKĹżECVKQPU
6GEJPKECNURGEKĹżECVKQPU
Frequency control
Crystal controlled PLL synthesizer
Transmit frequency
Handset: 1921.536-1928.448 MHz
Telephone base: 1921.536-1928.448 MHz
Channels
Nominal effective range
Maximum power allowed by FCC and IC. Actual operating range may
vary according to environment conditions at the time of use.
Power requirements
Handset: 2.4V Ni-MH battery
Telephone base: 6V DC @ 400mA
Charger: 6V AC @ 300mA
Memory
Handset directory:
50 memory locations; up to 30 digits and 15 characters
Handset call log:
50 memory locations; up to 24 digits and 15 characters
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc., Beaverton, Oregon 97008.
Distributed in Canada by VTech Technologies Canada Ltd., Richmond, B.C. V6W 1L5.
VTech is the registered trademark of VTech Holdings Limited.
Copyright Š 2011 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
14

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2011:12:30 15:35:36+08:00
Modify Date                     : 2011:12:30 15:35:36+08:00
Metadata Date                   : 2011:12:30 15:35:33+08:00
Creator Tool                    : PScript5.dll Version 5.2
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 6395 bytes, use -b option to extract)
Document ID                     : uuid:BD2F4FDBB832E111B952D54EBE9234BF
Instance ID                     : uuid:d35ce7c0-34f6-40d2-97cf-a653dd626df9
Derived From Instance ID        : uuid:2c3d8823-df53-4170-8bc5-1561403b7232
Derived From Document ID        : adobe:docid:indd:a476bdc8-c6f0-11e0-925d-83fc761746ef
Derived From Rendition Class    : proof:pdf
Format                          : application/postscript
Title                           : CS6519-X_SIMCIB_ULAPPROVAL_V1_20111013.pdf
Creator                         : kwkwan
Page Count                      : 27
Author                          : kwkwan

EXIF Metadata provided by EXIF.tools