VTech Telecommunications 80-9041-00 1.9GHz Digital Modulation Cordless Phone User Manual

VTech Telecommunications Ltd 1.9GHz Digital Modulation Cordless Phone

UserManual.wiki >

VTech Telecommunications >

80 9041 00 User Manual

User Manual

2Parts checklistYour telephone package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary.Telephone base and charger installationInstall the telephone base and charger as shown below.Use only the power adapters and batteries supplied with this product. To order a replacement, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.•Telephone base ChargerElectrical outlet (not controlled by a wall switch)Telephone base power adapterTelephone line cordTelephone wall jackA DSL lter (not included) is required if you have DSL high-speed Internet service. The DSL lter must be plugged into the telephone wall jack.Telephone line cordTelephone base power adapterHandset(4 for CS6199-4)Battery(4 for CS6199-4)Battery compartment cover(4 for CS6199-4)Charger and charger adapter(3 for CS6199-4)Telephone baseAbridged user’s manualAbridged user’s manualQuick start guideQuick start guideCharger adapterElectrical outlet (not controlled by a wall switch)

3Battery chargingOnce you have installed the battery, the screen indicates the battery status (see the table below). For best performance, keep the handset in the telephone base or charger when not in use. The battery is fully charged after 11 hours of continuous charging.Battery indicators Battery status ActionThe screen is blank, or displays Put in charger and ashes.The battery has no or very little charge. The handset cannot be used.Charge without interruption (at least 30 minutes).The screen displays Low battery and ashes. The battery has enough charge to be used for a short time.Charge without interruption (about 30 minutes).The screen displays HANDSET X.The battery is charged. To keep the battery charged, place it in the telephone base or charger when not in use.Battery installationInstall the battery as shown below.Plug the battery connector securely into the socket.1. Place the battery with the label THIS SIDE UP facing up and the wires inside the battery compartment.2.Slide the battery compartment cover towards the center of the handset until it clicks into place.3. Place the handset in the telephone base or charger to charge.4.

4Handset overviewTelephone base overviewCID/ /VOLUMEReview the caller ID log when the phone is not in use.Decrease the listening volume during a call or message playback.Scroll down while in a menu, or in the directory, caller ID log or redial list.Move the cursor to the left when entering numbers or names.••••/FLASHMake or answer a call.Answer another incoming call during a call.••MUTE/DELETEMute the microphone during a call.Delete digits or characters while using the dialing keys.Silence the ringer temporarily while the handset is ringing.Delete the displayed entry while in the directory, caller ID log or redial list.••••/ /VOLUMEReview the directory when the phone is not in use.Increase the listening volume during a call or message playback.Scroll up while in a menu, or in the directory, caller ID log or redial list.Move the cursor to the right when entering numbers or names.••••MENU/SELECTShow the menu.While in a menu, press to select an item, or save an entry or setting.••OFF/CANCELHang up a call.Silence the ringer temporarily while the handset is ringing.Press and hold to erase the missed call indicator while the phone is not in use.Press to return to the previous menu, or press and hold to return to idle mode, without making changes.••••REDIAL/PAUSEPress repeatedly to review the redial list.Press and hold to insert a dialing pause while dialing or entering a number.••QUIET# Press and hold to set and turn on the quiet mode, or turn it off. Press repeatedly to show other dialing options when reviewing a caller ID log entry.••INT Start an intercom conversation or transfer a call (for multi-handset models only).•Dialing keysEnter numbers or characters.•TONESwitch to tone dialing temporarily during a call.• Make or answer a call using the handset speakerphone.During a call, press to switch between the speakerphone and the handset.•• 1Press repeatedly to add or remove 1 in front of the caller ID log entry before dialing or saving it to the directory.Press and hold to set or dial your voicemail number.••FIND HANDSETPress to page all system handsets.•/SKIPSkip to the next message.• / PLAY/STOPPlay or stop playing messages.ANS ON/OFFTurn the answering system on or off.•/REPEATPress to repeat a message. Press twice to play the previous message.•• VOL+ and VOL- Adjust the volume during message playback.Adjust the telephone base ringer volume when the phone is not in use.••X/DELETEDelete the playing message.Press twice to delete all previously reviewed messages when the phone is not in use.••Message windowShows the number of messages, and other information of the answering system or telephone base.•

5Using the menuPress MENU when the phone is not in use.Press or until the screen displays the desired feature menu.Press SELECT.To return to the previous menu, press CANCEL.To return to idle mode, press and hold CANCEL.Telephone settingsDefault settings are indicated by asterisks (*).Menu setting Description OptionsLCD language Set the screen display language. English*FrançaisEspañolVoicemail # Set the speed dial voicemail number. Voicemail # -Clr voicemail Turn off the voicemail indicators (see the note below).Reset VM Icon?Key tone Set whether the handset beeps whenever a key is pressed.Key tone:On*Key tone:OffHome area code Set the home area code so that the caller ID log stores only seven digits for local telephone numbers.Home area code _ _ _Dial mode Set the telephone to be touch-tone or pulse dialing.Touch-tone*PulseThe following are some of the telephone features you may wish to set. Refer to Telephone settings in the online Complete user’s manual for complete instructions on setting all telephone features.Ringer volume (handset)You can adjust the ringer volume level, or turn the ringer off.Press MENU when the handset is not in use.Scroll to Ringers and then press SELECT twice.Press or to sample each volume level, then press SELECT to save.When the ringer volume is set to Off, the handset still rings when you press FIND HANDSET on the telephone base.Set date and time If you subscribe to caller ID service, the day, month and time are set automatically with each incoming call. You can also set the date and time manually.Press MENU when the handset is not in use.Scroll to Set date/time and then press SELECT.Use the dialing keys (0-9) to enter the month (MM), date (DD) and year (YY). Then press SELECT.Use the dialing keys (0-9) to enter the hour (HH) and minute (MM). Then press or to choose AM or PM. Press SELECT to save.Telephone operationMake a callPress or and then dial the telephone number.Answer a callPress , or any dialing key.End a callPress OFF or put the handset to the telephone base or charger.SpeakerphoneDuring a call, press to switch between speakerphone and normal handset use.VolumeDuring a call, press VOLUME/ or VOLUME/ to adjust the listening volume.1.2.3.••1.2.3.1.2.3.4.5.••••• Use the Clr voicemail feature when the telephone indicates there is new voicemail but there is none. For example, when you have accessed your voicemail while away from home. The Clr voicemail feature only turns off the indicators; it does not delete your voicemail messages. As long as you have new voicemail messages, your telephone service provider continues to send the signal that turns on the indicators.

6MuteThe mute function allows you to hear the other party but the other party cannot hear you.During a call, press MUTE. The screen displays Muted.Press MUTE again to resume the conversation. The screen displays Microphone on briey.Call waitingWhen you subscribe to call waiting service from your telephone service provider, you hear an alert tone if there is an incoming call while you are already on a call. Press FLASH to put the current call on hold and take the new call.Press FLASH at any time to switch back and forth between calls.Temporary ringer silencingWhen the telephone is ringing, you can temporarily silence the ringer of that handset without disconnecting the call. The next call rings normally at the preset volume.Press OFF or MUTE, then displays and Ringer muted displays briey.Temporary tone dialingIf you have pulse (rotary) service only, you can switch from pulse to touch-tone dialing temporarily during a call. During a call, press TONE .Use the dialing keys to enter the relevant number. The telephone sends touch-tone signals.The telephone automatically returns to pulse dialing mode after you end the call.Find handsetUse this feature to nd all system handsets.To start paging:Press FIND HANDSET on the telephone base. All idle handsets ring and display ** Paging **.To end paging:Press FIND HANDSET on the telephone base.Press , , OFF or any dialing key on a handset.Place the handset in the telephone base or charger.Do not press and hold FIND HANDSET for more than four seconds. It may lead to handset deregistration.Redial listEach handset stores the last 10 telephone numbers dialed. When there are already 10 entries, the oldest entry is deleted to make room for the new entry.To review and dial a number from the redial list:Press REDIAL when the phone is not in use.Press , or REDIAL repeatedly until the desired entry displays.Press or to dial.To delete a redial entry:When the desired redial entry displays, press DELETE.Chain dialingUse this feature to initiate a dialing sequence from numbers stored in the directory, caller ID log or redial list while you are on a call. Chain dialing can be useful if you wish to access other numbers (such as bank account numbers or access codes) from the directory, caller ID log or redial list. To access a number in the directory, caller ID log or redial list while on a call:To enter the directory, press MENU twice.-OR-To enter the caller ID log, press MENU then scroll to Caller ID log then press SELECT.-OR-To enter the redial list, press REDIAL.Scroll to the desired entry.Press SELECT to dial the displayed number.Join a call in progressYou can use up to two system handsets at a time on an outside call (for models with two or more handsets).When a handset is on a call, press or on another handset to join the call.Press OFF or place the handset in the telephone base or charger to exit the call. The call continues until all handsets hang up.1.2.•••1.2.3.••••1.2.3.1.2.3.••

7IntercomUse the intercom features for conversations between two handsets.Press INT on your handset when not in use. When you have three or more handsets, use the dialing keys to enter a destination handset number.To answer the intercom call, press , , INT or any dialing key on the destination handset.To end the intercom call, press OFF or place the handset back in the telephone base or charger.Answer an incoming call during an intercom callIf you receive an outside call during an intercom call, there is an alert tone.To answer the outside call, press . The intercom call ends automatically.To end the intercom call without answering the outside call, press OFF. The intercom call ends and the telephone continues to ring.Call transfer using intercomUse the intercom feature to transfer an outside call to another system handset.During a call, press INT. When you have three or more handsets, use the dialing keys to enter a destination handset number.To answer the intercom call, press , , INT or any dialing key on the destination handset. The outside call is now on hold and both handsets display Intercom. You can have a private conversation with the destination handset.From this intercom call, you have the following options: You can let the destination handset join you on the outside call in a three-way conversation. Press and hold INT on the originating handset. You can transfer the call. Press OFF, or place your handset back in the telephone base or charger. Your handset displays Transferred. The destination handset then automatically connects to the outside call. You can press INT to switch between the outside call (Outside call displays) and the intercom call (Intercom displays). The destination handset can end the intercom call by pressing OFF, or by placing the handset back in the telephone base or charger. The outside call continues with the originating handset.DirectoryThe directory can store up to 50 entries which are shared by all system handsets.To add a directory entry:Enter the number (up to 30 digits) when the phone is not in use then press SELECT. Then go to Step 3. -OR- When the phone is not in use, press MENU then scroll to Directory, and then press MENU twice.2. Use the dialing keys to enter the number (up to 30 digits). -OR- Copy a number from the redial list by pressing REDIAL and then press , or REDIAL repeatedly to select a number. Press SELECT to copy the number.Press SELECT to move on to enter the name.Use the dialing keys to enter the name (up to 15 characters). Additional key presses show other characters of that particular key.Press SELECT to store the entry.While entering names and numbers, you can:Press DELETE to backspace and erase a digit or character.Press and hold DELETE to erase the entire entry.Press or to move the cursor to the left or right. Press and hold PAUSE to insert a dialing pause (for entering numbers only).Press 0 to add a space (for entering names only).To review and dial a number from the directory:Entries are sorted alphabetically.Press when the phone is not in use.Scroll to browse through the directory, or use the dialing keys to start a name search.When the desired entry appears, press or to dial.To edit a directory entry:When the desired entry displays, press SELECT.Use the dialing keys to edit the number, then press SELECT.Use the dialing keys to edit the name, then press SELECT to conrm.To delete a directory entry:When the desired entry displays, press DELETE.When the handset displays Delete contact?, press SELECT.1.2.3.••1.2.3.••••1.3.4.5.•••••1.2.3.1.2.3.1.2.

8Speed dialYou can copy up to 9 directory entries into the speed dial locations (0 and 2-9) so that you can dial these numbers using fewer keys than usual.To assign a speed dial entry:Press MENU when the phone is not in use.Scroll to Directory, then press SELECT.Scroll to Speed dial, then press SELECT.Scroll to a desired speed dial location, then press SELECT.Scroll to a desired directory entry, then press SELECT to save.To dial a speed dial entry:Press and hold a dialing key (0 or 2-9) to dial the number stored in the corresponding location.To delete a speed dial entry:Press MENU when the phone is not in use.Scroll to Directory, then press SELECT.Scroll to Speed dial, then press SELECT.Scroll to a desired speed dial location, then press DELETE. The handset displays Clear SD #X? Press SELECT to conrm.Caller IDThis product supports caller ID services provided by most telephone service providers. Depending on your service subscription, you may see the caller’s name, number, date and time of calls that are sent by your telephone service provider after the rst or second ring.Caller ID logThe caller ID log stores up to 50 entries. If you answer a call before the caller ID information displays, it will not be saved in the caller ID log.The handset displays XX missed calls when you have incoming calls that have not been answered.If you want to erase the missed call indicator, press and hold CANCEL on the idle handset.To review and dial a number in the caller ID log:Press CID when the phone is not in use.Scroll to browse through the caller ID log. When the desired entry appears:Press # repeatedly to show different dialing options.Press 1 repeatedly if you need to add or remove 1 in front of the telephone number.Press or to dial.To save a caller ID log entry to the directory:When the desired caller ID log entry displays, press SELECT.Use the dialing keys to modify the number, if necessary. Then press SELECT.Use the dialing keys to modify the name, if necessary. Then press SELECT.To delete caller ID log entries:Delete an entry: When the desired caller ID log entry displays, press DELETE.Delete all entries: Press MENU when the phone is not in use. Scroll to Caller ID log and then press SELECT. Scroll to Del all calls then press SELECT twice.About answering system and voicemailYour telephone has separate indicators for two different types of voice messages: those left on the built-in answering system and those left at your telephone service provider’s voicemail. Each alerts you to new messages differently. If XX new messages displays on the handsets and the message window on the telephone base ashes, there are messages recorded on the built-in answering system. It can record and store up to 99 messages, depending on the length of each message. Each message can be up to 3 minutes in length. The total storage capacity for the announcement, messages and memos is approximately 14 minutes.If and New voicemail display on the handsets, your telephone service provider is indicating that it has new voicemail for you. Contact your telephone service provider for more information on how to access your voicemail.1.2.3.4.5.•1.2.3.4.••1.2.••3.1.2.3.••••

9Answering system settings Default settings are indicated by asterisks (*).Menu setting Description OptionsCall screening Set whether you hear the callers while they are leaving messages to you.Screening: On*Screening: Off# of rings Set the number of times the telephone rings before the answering system answers. 3*; 2; Toll saver; 6; 5; 4; Remote code Set a two-digit security code to access the answering system remotely from any touch-tone telephone.19*Msg alert tone Set whether the telephone beeps every 10 seconds to alert you of new messages.Tone: OnTone: Off*Recording time Set the recording time for each incoming message.3 minutes*2 minutes1 minuteSet number of ringsYou can set the answering system to answer an incoming call after 2, 3, 4, 5 or 6 rings; or toll saver. If you choose toll saver, the answering system answers a call after 2 rings when you have new messages, or after 4 rings when you have no new messages.Press MENU when the phone is not in use.Scroll to Answering sys and then press SELECT.Scroll to Ans sys setup and then press SELECT.Scroll to # of rings and then press SELECT.Press or to choose 6, 5, 4, 3, 2 or Toll saver and then press SELECT to save. Record your own announcementYou can use the preset announcement to answer calls, or replace it with your own recorded announcement. The announcement can be up to 90 seconds in length.Press MENU when the phone is not in use.Scroll to Answering Sys then press SELECT twice.The handset announces, “To play, press 2. To record, press 7.” Then press 7 to record.The handset announces, “Record after the tone. Press 5 when you are done.” After the tone, speak towards the handset microphone.Press 5 when done.Answering system operationTurn the answering system on or offThe answering system must be turned on to answer and record messages. Press ANS ON/OFF on the telephone base to turn the built-in answering system on or off. Message playback at the telephone base Press /PLAY when the phone is not in use.Options during playback:Press VOL+ or VOL- to adjust the speaker volume.Press /SKIP to skip to the next message.Press /REPEAT to repeat the message currently playing. Press /REPEAT twice to listen to the previous message.Press X/DELETE to delete the current message. The system advances to the next message.Press /STOP to stop.Delete all messages at the telephone basePress X/DELETE twice when the phone is not in use.Call interceptIf you want to talk to the person whose message is being recorded, press or on the handset.1.2.3.4.5.1.2.3.4.5.••••••

10Access the answering system remotelyDial your telephone number from any touch-tone telephone.When the system plays the announcement, enter the two-digit remote code. The preset code is 19.Enter one of the following remote commands.Command Description1Play all messages.2Play only new messages.3Delete the current message (during playback).33 Delete all old messages.4Repeat the current message (during playback).5Stop.*5 Hear a list of remote commands.6Skip to the next message (during playback).*7 Record a new announcement.8End the call.0Turn the answering system on or off.4. Hang up or press 8 to end the call.TroubleshootingIf you have difculty with your telephone, please try the suggestions below. For customer service, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377. My telephone does not work at all.Make sure the battery is installed and charged correctly. For optimum daily performance, return the handset to the telephone base or charger after use.Make sure the power adapter is securely plugged into an outlet not controlled by a wall switch.Make sure the telephone line cord is plugged rmly into the telephone base and the wall jack.Unplug the electrical power to the telephone base. Wait for approximately 15 seconds, then plug it back in. Allow up to one minute for the cordless handset and telephone base to synchronize.Charge the battery in the handset for up to 11 hours.If the battery is completely depleted, charge the handset for at least 30 minutes before use.Remove the battery and then install it again. If that still does not work, it may be necessary to purchase a new battery.Disconnect the telephone base from the telephone wall jack and plug in a working telephone. If the other telephone does not work, the problem is probably in the wiring or the telephone service. Contact your telephone service provider.I cannot dial out.Try all the above suggestions.Make sure there is a dial tone before dialing. It is normal if the handset takes a second or two to synchronize with the telephone base before producing a dial tone. Wait an extra second before dialing.If other telephones in your home are having the same problem, the problem is in the wiring or telephone service. Contact your telephone service provider (charges may apply).Eliminate any background noise. Mute the cordless handset before dialing, or dial from another room in your home with less background noise.The answering system does not answer after the correct number of rings.Make sure the answering system is on. When the answering system is on, the ANS ON/OFF light on the telephone base should be lit and ANS ON should display on the handsets.If toll saver is selected, the number of rings changes to two when there are new messages waiting.If the memory is full or if the answering system is off, the answering system answers after 10 rings.In some cases, the answering system is affected by the ringing system used by your telephone service provider.If you subscribe to voicemail service, change the number of rings so that your answering system answers before your voicemail answers. To determine how many rings activate your voicemail, please contact your telephone service provider.If there is a fax machine connected to the same telephone line, try disconnecting the fax machine. If that solves the problem, consult your fax machine documentation for information on compatibility with answering systems.The answering system does not record messages.Make sure the answering system is on.When the answering machine memory is full, it does not record new messages until some old messages are deleted.If you subscribe to voicemail service, change the number of rings so that your answering system answers before your voicemail answers. To determine how many rings activate your voicemail, please contact your telephone service provider.If there is a fax machine connected to the same telephone line, try disconnecting the fax machine. If that solves the problem, consult your fax machine documentation for information on compatibility with answering systems.1.2.3.••••••••••••••••••••••

11The messages on the answering system are incomplete.If a caller leaves a very long message, part of it may be lost when the answering system disconnects the call after the preset recording time.If the memory on the answering system becomes full during a message, the answering system stops recording and disconnects the call.If the caller’s voice is very soft, the answering system may stop recording and disconnect the call.I have accidentally set my LCD language to Spanish or French, and I don’t know how to change it back to English.While the phone is not in use, press MENU once then enter 364#.While on a call, press MENU once then enter 364#. Then the call ends automatically. Common cure for electronic equipment.If the telephone is not responding normally, put the cordless handset in the telephone base. If it does not respond, try the following (in the order listed):1. Disconnect the power to the telephone base.2. Disconnect the battery on the cordless handset.3. Wait a few minutes before connecting power to the telephone base.4. Install the battery again and place the cordless handset in the telephone base.5. Wait for the cordless handset to synchronize with the telephone base. Allow up to one minute for this to take place.Important safety instructionsWhen using your telephone equipment, basic safety precautions should always be followed to reduce the risk of re, electric shock and injury, including the following:Read and understand all instructions.Follow all warnings and instructions marked on the product.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a swimming pool, or in a wet basement or shower.Do not place this product on an unstable table, shelf, stand or other unstable surfaces.Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home or ofce, consult your dealer or local power company.Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on.Never push objects of any kind into this product through the slots in the telephone base or handset because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the telephone base or handset other than specied access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.Do not overload wall outlets and extension cords.Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:When the power supply cord or plug is damaged or frayed.If liquid has been spilled onto the product.If the product has been exposed to rain or water.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operation instructions. Improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.If the product has been dropped and the telephone base and/or handset has been damaged.If the product exhibits a distinct change in performance.Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced in its cradle. This is a common event associated with the closing of any electrical circuit. The user should not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the phone is located in an environment containing concentrations of ammable or ame-supporting gases, unless there is adequate ventilation. A spark in such an environment could create a re or explosion. Such environments might include: medical use of oxygen without adequate ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.Only put the handset of your telephone next to your ear when it is in normal talk mode.The power adapters are intended to be correctly oriented in a vertical or oor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.SAVE THESE INSTRUCTIONSPrecautions for users of implanted cardiac pacemakersCardiac pacemakers (applies only to digital cordless telephones):Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:Pacemaker patientsShould keep wireless telephones at least six inches from the pacemaker.Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is turned ON.Should use the wireless telephone at the ear opposite the pacemaker.WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless telephones.••••••1.2.3.4.5.6.7.8.9.10.11.12.••••••13.14.15.16.•••

12Operating rangeThis cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and telephone base can communicate over only a certain distance - which can vary with the locations of the telephone base and handset, the weather, and the layout of your home or ofce.When the handset is out of range, the handset displays Out of range or no pwr at base.If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect well when you press . Move closer to the telephone base, then press to answer the call.If the handset moves out of range during a telephone conversation, there may be interference. To improve reception, move closer to the telephone base.ECO modeThis power conserving technology reduces power consumption for optimal battery performance, according to the distance between the telephone base and the handset. When the telephone base communicates with the handset, ECO mode will be activated automatically. MaintenanceTaking care of your telephoneYour cordless telephone contains sophisticated electronic parts, so it must be treated with care.Avoid rough treatmentPlace the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it.Avoid waterYour telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with wet hands. Do not install the telephone base near a sink, bathtub or shower.Electrical stormsElectrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, take caution when using electrical appliances during storms.Cleaning your telephoneYour telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft cloth slightly dampened with water or mild soap. Do not use excess water or cleaning solvents of any kind.About cordless telephonesPrivacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone base and the cordless handset by radio waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones.Electrical power: The telephone base of this cordless telephone must be connected to a working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the cordless handset if the telephone base is unplugged, switched off or if the electrical power is interrupted.Potential TV interference: Some cordless telephones operate at frequencies that may cause interference to televisions and VCRs. To minimize or prevent such interference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR often reduces or eliminates the interference.Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with conducting material such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm. Observe proper polarity between the battery and the battery charger.Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could release caustic material which could cause injury.The RBRC® sealThe RBRC® seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.The RBRC® program provides a convenient alternative to placing used nickel-metal hydride batteries into the trash or municipal waste, which may be illegal in your area.VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers participating in the RBRC® program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERYTM for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.Limited warrantyWhat does this limited warranty cover?The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada.What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days.How long is the limited warranty period?The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.•••••Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the unplugged cords.

13What is not covered by this limited warranty?This limited warranty does not cover:1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, re, water or other liquid intrusion; or2. Product that has been damaged due to repair, alteration or modication by anyone other than an authorized service representative of VTech; or3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or4. Product to the extent that the problem is caused by use with non-VTech accessories; or5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or7. Product returned without a valid proof of purchase (see item 2 below); or8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.How do you get warranty service?To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save you a service call.Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.What must you return with the Product to get warranty service?1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difculty; and2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and3. Provide your name, complete and correct mailing address, and telephone number.Other limitationsThis warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modications to this limited warranty and you should not rely on any such modication.State/Provincial Law Rights: This warranty gives you specic legal rights, and you may also have other rights, which vary from state to state or province to province.Limitations: Implied warranties, including those of tness for a particular purpose and merchantability (an unwritten warranty that the Product is t for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost prots or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.Please retain your original sales receipt as proof of purchase.FCC, ACTA and IC regulationsFCC Part 15This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.Changes or modications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more.This Class B digital apparatus complies with Canadian ICES-003.FCC Part 68 and ACTAThis equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identier in the format US:AAAEQ##TXXXX. This identier must be provided to your telephone service provider upon request.The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See the installation instructions in the user’s manual.The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be ve (5.0) or less. For more information, please contact your telephone service provider.This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone service provider or a qualied installer.••••

14If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited warranty.If this equipment is causing harm to the telephone network, the telephone service provider may temporarily discontinue your telephone service. The telephone service provider is required to notify you before interrupting service. If advance notice is not practical, you will be notied as soon as possible. You will be given the opportunity to correct the problem and the telephone service provider is required to inform you of your right to le a complaint with the FCC. Your telephone service provider may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone service provider is required to notify you if such changes are planned.If this product is equipped with a corded or cordless handset, it is hearing aid compatible.If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, re, medical) in these locations. If you do store or test emergency numbers, please:Remain on the line and briey explain the reason for the call before hanging up.Perform such activities in off-peak hours, such as early morning or late evening.Industry CanadaOperation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation.The term ‘’IC:‘’ before the certication/registration number only signies that the Industry Canada technical specications were met.The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed ve.This product meets the applicable Industry Canada technical specications.Technical specicationsFrequency control Crystal controlled PLL synthesizerTransmit frequency Handset: 1921.536-1928.448 MHzTelephone base: 1921.536-1928.448MHzChannels 5Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.Power requirements Handset: 2.4V Ni-MH batteryTelephone base: 6V DC @ 400mACharger: 6V AC @ 300mAMemory Handset directory: 50 memory locations; up to 30 digits and 15 characters Handset caller ID log: 50 memory locations; up to 24 digits and 15 charactersVTECH TELECOMMUNICATIONS LTD.A member of THE VTECH GROUP OF COMPANIES.Distributed in the U.S.A. by VTech Communications, Inc., Beaverton, Oregon 97008.Distributed in Canada by VTech Technologies Canada Ltd., Richmond, B.C. V6W 1L5.VTech is the registered trademark of VTech Holdings Limited.Copyright © 2012 for VTECH TELECOMMUNICATIONS LTD.All rights reserved. Printed in China.91-006209-010-100

Navigation menu