VTech Telecommunications 80-9982-01 Audio Monitor-Baby Unit User Manual DM226 CIB V1 20170303

VTech Telecommunications Ltd Audio Monitor-Baby Unit DM226 CIB V1 20170303

User Manual

Download: VTech Telecommunications 80-9982-01 Audio Monitor-Baby Unit User Manual DM226 CIB V1 20170303
Mirror Download [FCC.gov]VTech Telecommunications 80-9982-01 Audio Monitor-Baby Unit User Manual DM226 CIB V1 20170303
Document ID3316655
Application IDa+5Qm+3Xdx8etzpmwSC6kw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize99.63kB (1245363 bits)
Date Submitted2017-03-15 00:00:00
Date Available2017-03-15 00:00:00
Creation Date2017-03-10 12:38:43
Producing SoftwareGPL Ghostscript 9.07
Document Lastmod2017-03-10 12:38:43
Document Title-DM226_CIB_V1_20170303.pdf
Document CreatorPDFCreator Version 1.7.1
Document Author: stanleyl

Congratulations
DM226
DM226-2
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
on purchasing your new VTech product. Before
using this product, please read Important
safety instructions.
This manual has all the feature operations and
troubleshooting necessary to install and operate
your new VTech product. Please review this
manual thoroughly to ensure proper installation
and operation of this innovative and feature rich
VTech product.
®
Safe & Sound
Digital Audio Monitor
BC
For support, shopping, and everything new at
VTech, visit our website at
www.vtechphones.com.
Install the battery
The parent unit runs on rechargeable battery or
AC power. To continuously monitor your baby,
make sure you use both battery and AC power
at the same time. With the battery alone, the
parent unit can cordlessly run for a short time
only.
Replace the battery
Charge the parent unit battery
To replace the battery, pull out the battery
compartment cover, and then lift up the battery.
Follow the previous steps to install the battery.
When you have connected the parent unit and
installed its battery for the first time, it powers
on automatically. The battery icon indicates the
battery status (see the following table).
NOTES
Use only the battery supplied with this product.
•
The operating time for using the rechargeable
battery is short. If you want to monitor your baby for
a long time, we recommend you connect the parent
unit to AC power.
•
•
Make sure the electrical outlets are not controlled
by wall switches.
If the parent unit will not be used for a long time,
disconnect and remove the battery to prevent
possible leakage.
•
The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if
it is plugged into a ceiling, under-the-table or cabinet
outlet.
•
What’s in the box
Install the battery as shown below
•
Use only the power adapters supplied with this
product.
Test your baby monitor
•
It takes longer to charge the battery when the
parent unit is turned on. To shorten the charging
time, turn the parent unit off while charging.
You may test the baby monitor before initial use,
and at regular times thereafter.
•
The standby time varies depending on the
voice-activated (VOX) sensitivity level you set, your
actual use and the age of the battery.
Battery
indicators
Battery status
Action
The battery
icon is off.
No battery is
installed but
operates using
AC power.
Install the
parent unit
battery.
Charge without
interruption
(at least 30
minutes).
Make sure the parent unit, the baby unit and the
power adapter cords are out of reach of children.
Abnormal
battery is
detected.
Connect the baby monitor
THIS SIDE UP
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT186692 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
CR0920
Made in China / Fabriqué en chine
NOTE
Make sure the THIS SIDE UP is facing up while
inserting the battery.
1 set for DM226;
2 sets for DM226-2
This baby monitor is intended as an aid. It is not a
substitute for proper adult supervision, and should
not be used as such.
The parent unit battery is fully charged after 11
hours of continuous charging.
-OR-
•
•
•
NOTES
•
CAUTION
•
NOTE
NOTES
Connect and charge the
battery
Positioning the baby monitor
Before use
The screen The battery
has very little
displays
LOW
charge and
BATTERY
may be used
and
for only a short
The
time.
light
flashes.
Charge without
interruption
(about 30
minutes).
The battery
icon
becomes
solid .
To keep
the battery
charged,
connect it to AC
power when not
in use.
The battery is
fully charged.
For hearing protection, make sure the
parent unit is more than 2 meters (6.5 feet)
away from the baby unit. If you hear any
high-pitched noise, move the parent unit
further until the noise stops. You can also
press
on the parent unit to lower or mute
the noise.
Battery Pack / Bloc-piles :
BT186692 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATT
NE PAS INCINÉRER OU PERCER LE
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ V
> 2m (6.5ft)
< 2m (6.5ft)
1. Make sure your baby unit and parent unit are
on.
2. Speak towards the microphone of the baby
unit. You will hear the sound at the parent
unit, and see the visual sound indicators
light up.
Microphone
On/off
• Press to turn on or off the night light.
Night light
• On when night light is turned on
manually.
• On automatically when the baby unit
detects sounds, which light up four
sound level indicators on the parent
unit.
• Off when night light is turned off
manually.
On/off
• Press to power on, the power light turns
on.
• Press and hold to power off, the power
light turns off.
PAGE
• Press to start or stop paging parent
unit.
Microphone
• Press to increase the speaker volume.
LCD panel
Battery level indicator
• Light on when the battery is being
charged.
• Light flashes when the battery is low
and needs charging.
• Light off when no battery is installed,
or abnormal battery is detected.
g k
• Press to power on, the screen turns
on.
• Press and hold to power off, the
screen turns off.
• While in a menu, press to return to
idle screen.
SELECT
• While in a menu, press to choose an
item, or save a setting.
Parent unit display icons
Connection status
displays when strong signal
strength is detected between the
baby unit and the parent unit.
•
displays when moderate signal
strength is detected between the
baby unit and the parent unit.
•
displays when the weak signal
strength is detected between the
baby unit and the parent unit.
•
flashes when the link between the
baby unit and the parent unit is lost.
•
Night light
• On when the night light is turned on.
Sound alert
• Press to increase the speaker volume.
• While in a menu, press to scroll up.
10
• Press to decrease the speaker
volume.
• While in a menu, press to scroll down.
• Displays when the sound alert of the
parent unit is turned on.
• Flashes when there are loud sounds
detected from the baby unit and the
parent unit is in mute.
Vibration alert
11
Power jack
12
Speaker
• Displays when the vibration alert of
the parent unit is turned on.
• Flashes when there are loud sounds
detected from the baby unit.
13
Belt clip
Mute
14
Battery compartment cover
• Displays when the volume is turned
off.
Visual sound indicator
The visual sound indicator has two
functions. One is to show the sound level
detected by the baby unit. The other
one is to show the volume level during
speaker volume setting.
TALK
• Press and hold to talk to the baby unit;
release to stop talking.
• While in a menu, press to return to
idle screen.
MENU/
• Press to enter the menu while idle.
• While in a menu, press to return to the
previous screen.
• Press to return to idle screen.
Sound level detected by the baby unit
Battery status
•
•
One to three green
lights indicate a moderate sound level
detected by the baby unit.
•
Additional red lights
indicate a higher sound level detected
by the baby unit (e.g. baby crying
loudly).
Speaker volume level
•
•
•
•
• Press to decrease the speaker
volume.
Speaker
Power jack
CAUTION
•
NOTE
•
When the parent unit displays NOT LINKED and
flashes, move the parent unit closer to the baby
unit (observe the minimum distance of 2 meters/
6.5 feet). You can also check if the baby monitor is
connected to a live power socket and switched on.
Increase the speaker volume of the parent unit if
you cannot hear the sounds transmitted from the
baby unit.
The default volume of your parent unit is level 3. If
you experience high-pitched screeching noise from
your baby monitor while positioning:
- Make sure your baby unit and parent unit are
more than 2 meters (6.5 feet) apart, OR
- Turn down the volume of your parent unit.
Operating range
The operating range of the baby monitor is up to
300 meters (1,000 feet) outdoors or 50 meters
(160 feet) indoors. The actual operating range
may vary depending on the environmental
conditions, and other interferences such as
walls, doors, and other obstructions.
THIS SIDE UP / CE CÔTÉ VER
Place the parent unit more than 2 meters
(6.5 feet) away from the baby unit.
ry Pack / Bloc-piles :
2.
6692 (2.4V 400mAh Ni-MH)
NING / AVERTISSEMENT :
OT BURN OR PUNCTURE BATTE
AS INCINÉRER OU PERCER LES
in China / Fabriqué en chine
Parent unit overview
Baby unit overview
> 1m (3ft)
> 2m (6.5ft)
TIP
Overview
1. Place the baby unit more than 1 meter
(3 feet) away from your baby.
CAUTION
•
•
User’s manual
Keep the baby unit out of the reach of the baby.
Never place or mount the baby unit inside the
baby’s crib or playpen.
One to three green
lights indicate Level 1 to Level 3 of the
speaker volume setting.
•
Additional red lights
indicate Level 4 to Level 5 of the
speaker volume setting.
•
animates when
the battery is charging.
displays solid when the battery is
fully charged.
flashes when the battery is
charged with AC adaptor, or
charging failure.
flashes when the battery is in low
level and needs charging.
No battery icon displays when there
is no battery installed, or abnormal
battery is detected.
Parent unit display screen
messages
LINKED
The link between the parent unit
and the baby unit is established.
LOW
The parent unit uses only the
rechargeable battery pack and it
needs to be recharged.
BATTERY
LINKED
The link between the parent
unit and the baby unit is lost
continuously for over 10 seconds.
PAGING
All idle parent units are being
paged by the baby unit.
NOT
SAVED
Using the baby monitor
Power on or off the baby unit
• Press
to power on the baby unit. The
power light turns on.
to power off the baby unit.
• Press and hold
The power light turns off.
Adjust the Voice-activated (VOX) sensitivity
level of the baby unit
You can choose to hear sounds from the baby
unit all the time, or to hear sounds that exceed
a certain level. You can use the parent unit to
adjust the microphone sensitivity of your baby
unit. The higher the VOX sensitivity level, the
more sensitive the baby unit is in detecting
sounds for transmitting to the parent unit. The
VOX sensitivity level is preset to HIGHEST.
VOX sensitivity level table for reference
Display
HIGHEST
Sensitivity
Description
High
sensitivity
Highest VOX level
The parent unit speaker is
constantly on, and you will
hear all sounds (including
background noises) from
your baby’s room.
Your selection has been saved.
SEARCHING The parent unit is out of range of
the baby unit, or the baby unit is
out of power.
TALK
The parent unit is talking to the
baby unit.
TALKBACK
The other parent unit is talking to
the baby unit.
Power on or off the parent unit
to power on the parent unit. The
• Press
screen turns on.
to power off the parent
• Press and hold
unit. The screen turns off.
High VOX level
The parent unit speaker
turns on for soft babbling
and louder sounds from
your baby. It remains
quiet when your baby
sleeps soundly.
HIGH
Medium VOX level
The parent unit speaker
turns on for loud babbling
and louder sounds from
your baby. It remains quiet
when your baby makes
soft sounds.
MEDIUM
Low VOX level
The parent unit speaker
turns on for crying and
louder sounds from your
baby. It remains quiet
when your baby makes
soft sounds.
NOTE
•
The parent unit powers on automatically once
it is connected to AC power or battery installed.
The baby unit also powers on automatically once
connected to AC power.
LOW
Adjust the speaker volume for baby unit
•
Press
any time.
or
on the baby unit at
Adjust the speaker volume for parent unit
You can adjust the speaker volume from
VOLUME 1 to VOLUME 5, or turn it off. The
speaker volume is preset to VOLUME 3.
•
Press
or
when the parent unit is not in
use.
When the speaker volume is set to off, the
screen displays .
LOWEST
Low
sensitivity
Lowest VOX level
The parent unit speaker
turns on for loud crying or
screeching sounds from
your baby. It remains quiet
when your baby makes
soft sounds.
1. Press MENU when the parent unit is not in
use.
2. Press SELECT to select VOX LEVEL.
or
to choose the VOX Level.
3. Press
4. Press SELECT to confirm your selection.
The screen displays SAVED and you hear a
confirmation tone.
NOTE
•
To enter the VOX Level menu of the parent unit,
the baby unit must be turned on.
Sound alert
If you turn on the sound alert, the parent unit
beeps when the baby unit detects sounds which
light up the red light of visual sound indicator on
the parent unit.
When the sound alert of the parent unit is turned
on,
displays. The sound alert is preset to OFF.
1. Press MENU when the parent unit is not in
use.
2. Press
or
to choose SOUND ALERT,
then press SELECT.
3. Press
or
to choose ON or OFF.
4. Press SELECT to confirm your selection.
The screen displays SAVED and you hear a
confirmation tone.
NOTE
•
The sound alert setting on each parent unit is
independent.
Vibration alert
You can turn on the vibration alert so that the
parent unit vibrates when the baby unit detects
sounds which light up the red light of visual
sound indicator on the parent unit.
When the vibration alert of the parent unit is
turned on, displays. The vibration alert is
preset to OFF.
1. Press MENU when the parent unit is not in
use.
2. Press
or
to choose VIBE ALERT, then
press SELECT.
3. Press
or
to choose ON or OFF.
4. Press SELECT to confirm your selection.
The screen displays SAVED and you hear a
confirmation tone.
NOTES
•
•
Each time you set the vibration alert to ON,
the parent unit vibrates briefly after you press
SELECT.
The vibration alert setting on each parent unit is
independent.
Nightlight
You can turn on or off the nightlight by pressing
button on the baby unit. You can also use the
parent unit to turn on or off the nightlight on the
baby unit.
Set default
Use this feature to restore to the default settings.
Restoring the default settings on one parent
unit will also reset the shared settings for VOX
sensitivity level of the other parent unit.
Using the baby unit:
1. Press MENU when the parent unit is not in
use.
1. Press
to turn on the nightlight.
2. Press
again to turn off the nightlight.
2. Press
or
to choose SET DEFAULT,
then press SELECT.
Using the parent unit:
3. Press
1. Press MENU when the parent unit is not in
use.
4. When you choose YES, press SELECT to
confirm your selection. The screen displays
SAVED and you hear a confirmation tone.
2. Press
or
to choose NIGHTLIGHT,
then press SELECT.
3. Press
or
When you choose NO, press SELECT to
confirm your selection. The screen displays
the previous menu.
4. Press SELECT to confirm your selection.
The screen displays SAVED and you hear
a confirmation tone.
Nightlight will be turned on automatically,
whenever the baby unit detects sounds reached
the red sound level indicators on the parent unit.
The nightlight will go off automatically after 15
minutes of silence.
NOTES
•
•
•
When the nightlight is turned on, the parent unit
displays .
The nightlight on baby unit operates even the
parent unit is out of battery or being turned off.
If the parent unit lost link, the nightlight icon
in parent unit will disappear, regardless of the
nightlight status.
Language
You can select a language (English, French or
Spanish) to be used in all screen displays. The
language is preset to English.
1. Press MENU when the parent unit is not in
use.
2. Press
or
to choose LANGUAGE, then
press SELECT.
3. Press
or
to choose ENGLISH,
FRANCAIS or ESPANOL.
4. Press SELECT to confirm your selection.
The screen displays SAVED and you hear a
confirmation tone.
NOTE
•
to choose YES or NO.
-OR-
to choose ON or OFF.
Nightlight Auto-on
or
Talk to the baby unit
You can broadcast messages from a parent unit
to the baby unit and the other parent unit. If you
have two parent units, you can use both of them
at the same time to talk to the baby unit.
• Press and hold TALK on the side of the
parent unit. The screen displays TALK when
the voice connection to the baby unit is
made. Speak towards the MIC on the parent
unit. Your voice is broadcast to the baby unit
and the other parent unit.
NOTES
•
•
When a parent unit is talking to the baby unit, it is
also broadcast to the other parent unit. However,
sounds from the baby unit cannot be transmitted
to the parent units at the moment.
If speaker volume of the parent unit has been
turned off before the talk, it will change to default
volume level after the talk finished.
General product care
To keep this product working well and looking good,
follow these guidelines:
• Avoid putting it near heating appliances and
devices that generate electrical noise (for
example, motors or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby
unit in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry
before you connect them to the mains again.
Storage
When you are not going to use the baby monitor for
some time, remove the rechargeable battery from the
parent unit. Store the parent unit, the baby unit and the
adapters in a cool and dry place.
Frequently asked questions
•
•
Paging rings all parent units even if the speaker
volume of parent unit is set to VOLUME OFF.
The baby unit cannot page any parent unit that is
turned off, out of range, or talking to the baby unit.
Perhaps the baby unit is not
connected to the power. Connect
the baby unit to the power.
Why does the
baby monitor
produce a highpitched noise?
The units may be too close to
each other. Make sure the parent
unit and the baby unit are more
than 2 meters (6.5 feet) away from
each other.
Why does the
parent unit react
too quickly to
other sounds?
The baby unit also detects other
sounds than those of your baby.
Adjust the VOX sensitivity level to
a lower level or adjust the speaker
volume on the parent unit.
Why don’t I hear The volume of the parent unit
a sound/Why
may have set too low. Press
to
can’t I hear my
increase the volume level.
baby cry?
You may have set a low VOX
sensitivity level. See Adjust the
Voice-activated (VOX) level
of the baby unit to change the
setting.
Why does the
parent unit
beep?
Why does the
baby monitor
not respond
normally?
Why doesn’t
the screen of
the parent unit
go on when I
switch on the
unit?
Try the following (in the order
listed) for common cure:
1. Disconnect the power to the
baby unit and the parent unit.
2. Remove the batteries in the
parent unit. Then, install the
batteries again.
3. Wait a few minutes before
connecting power back to the
baby unit and the parent unit.
4. Turn on the baby unit and the
parent unit.
5. Wait for the parent unit to
synchronize with the baby unit.
Allow up to one minute for this
to take place.
If the parent unit is in mute and
the sound alert feature is on,
there is sound detected from the
baby unit.
The baby unit may be out of
range. Move the parent unit
closer to the baby unit (but not
less than 6.5 feet).
Below are the questions most frequently asked about
the baby monitor. If you cannot find the answer to your
question, visit our website at www.vtechphones.com
or call 1 (800) 595-9511 for customer service.
Find/page the parent unit
Use this feature to find misplaced parent units.
1. Press PAGE on the baby unit. All idle parent
units ring and display PAGING.
2. To end paging, press any key on the parent
unit, or press PAGE on the baby unit.
NOTES
Why doesn’t the
POWER light
of the baby unit
go on when I
switch on the
unit?
If the parent unit is powered
by the provided battery, it may
not have enough charge for the
parent unit to perform normally.
Charge the battery in the parent
unit for up to 11 hours.
Why can’t I
establish a
connection?
Why is the
connection lost
every now and
then? Why are
there sound
interruptions?
The baby unit may be out of
range. Move the parent unit
closer to the baby unit (but not
less than 6.5 feet).
Other electronic products may
cause interference with your baby
monitor. Try installing your baby
monitor as far away from these
electronic devices as possible.
Perhaps the rechargeable battery
of the parent unit is empty and the
parent unit is not connected to the
power. Insert the appliance plug
into the parent unit and put the
adapter in a wall socket.
The language setting on each parent unit is
independent.
Changes or modifications to this equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product. This
product has been tested and found to comply with the
FCC criteria. The baby unit shall be installed and used
such that parts of all persons’ body are maintained
at a distance of approximately 8 in (20 cm) or more.
The transmitter and antenna of the parent unit shall be
held at least 1 in (2.5 cm) from your face.
For body-worn operation, this parent unit has been
tested and meets the FCC RF exposure guidelines.
Use of other accessories may not ensure compliance
with FCC RF exposure guidelines.
Industry Canada
This device complies with Industry Canada licenceexempt RSS standard(s).
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation.
The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
This product meets the applicable Innovation, Science
and Economic Development Canada technical
specifications.
This Class B digital apparatus complies with Canadian
requirement:
CAN ICES-3(B)/NMB-3(B).
RF radiation exposure statement
The baby unit complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The baby unit should be installed and
operated with a minimum distance of 8 in (20 cm)
between the baby unit and all persons’ body. Use of
other accessories may not ensure compliance with
FCC RF exposure guidelines. This transmitter must
not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment complies
also with Industry Canada RSS-102 with respect to
Canada’s Health Code 6 for Exposure of Humans to
RF Fields.
California Energy Commission
battery charging testing mode
This baby monitor meets the California Energy
Commission (CEC) regulations for energy consumption.
Your baby monitor is set up to comply with the energyconserving standards right out of the box.
Follow the instructions to install and charge the
battery. The CEC battery charging testing mode is
activated while charging.
Even if the parent unit is paired to baby unit, the CEC
battery charging testing mode is activated while it is
powered off and charging.
For c-UL compliance only
Mesures de sécurité importantes
Lorsque vous utilisez votre appareil, vous devriez
toujours suivre certaines mesures de précaution
de base afin de réduire les risques d’incendie,
d’électrocution et de blessures corporelles, dont ceux
qui suivent:
1. Observez toutes les instructions et mises en garde
inscrites sur l’appareil.
2. L’installation par un adulte est requise.
3. Ce produit a été conçu pour être un dispositif
d’appoint seulement. Il n’est pas le remplacement
d’une supervision responsable et adéquate par un
adulte et ne devrait pas être utilisé comme telle.
4. Ce produit n’est pas conçu pour être utilisé en tant
que moniteur médical.
5. N’utilisez pas cet appareil près de l’eau ni de toute
autre source d’humidité, par exemple, près d’une
baignoire, cuve à lessive, évier de cuisine, dans
un sous-sol humide ni près d’une piscine, dans un
soussol humide ou une douche.
6. MISE EN GARDE: Il peut y avoir un risque
d’explosion si vous utilisez le mauvais type de piles
pour l’unité du parent. N’utilisez que le bloc-piles
rechargeable inclus ou le bloc-piles de rechange
(BT166342/BT266342). N’incinérez pas les piles.
Celles-ci risqueraient d’exploser. Jetez les piles
usées selon les renseignements suivant le sceau
du RBRCMD.
7. N’utilisez que les adaptateurs inclus avec ce
produit. L’utilisation d’un adaptateur dont la
polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre
votre sécurité en péril.
Adaptateur de l’unité du bébé: Sortie : 6 V CC 400
mA. Adaptateur de l’unité du parent: Sortie : 6 V
CC 400 mA.
8. Lorsqu’ils sont branchés dans une prise de
courant, les adaptateurs secteur ont été conçus
pour être orientés correctement, soit à la verticale
ou au plancher. Les broches n’ont pas été conçues
pour supporter le poids du bloc d’alimentation et
le maintenir en place si celuici est branché dans
une prise au plafond, sous une table ou dans un
meuble.
9. Pour les PRODUITS À BRANCHER À UNE
PRISE DE COURANT, la prise de courant doit
être installée près du produit, afin d’assurer une
accessibilité sécuritaire à la prise de courant.
10. Débranchez ce produit de la prise de courant
avant de procéder au nettoyage. N’utilisez pas de
nettoyants en aérosols. Utilisez un chiffon humide
pour le nettoyer.
11. Débranchez les cordons d’alimentation avant de
remplacer le bloc-piles.
12. Ne coupez pas les cordons d’alimentation pour
remplacer les fiches, car ceci peut présenter un
danger potentiel.
13. Ne laissez aucun objet reposer ni appuyer sur le
cordon d’alimentation. N’installez pas cet appareil
dans un endroit où l’on risque d’écraser le cordon
d’alimentation ou de le piétiner.
14. Ne faites fonctionner cet appareil qu’avec le type
d’alimentation indiqué sur l’étiquette. Si vous
ne connaissez pas le type d’alimentation que
vous possédez à votre domicile, consultez votre
marchand ou votre compagnie locale d’électricité.
15. Ne surchargez pas les prises de courant murales
ni les rallonges électriques.
16. Ne placez pas cet appareil sur un chariot, meuble,
trépied, support de montage ni table chancelants.
17. Les trous et ouvertures du boîtier, situés à l’arrière
de l’appareil ou sous celui-ci, servent à aérer
l’appareil. Pour l’empêcher de surchauffer, ne
bloquez sous aucun prétexte ces ouvertures et
n’empêchez pas l’aération adéquate de l’appareil
en le plaçant sur un lit, divan, tapis ou toute autre
surface similaire. De même, ne le positionnez pas
à proximité ni au-dessus d’une source de chaleur
ou d’un calorifère. De plus, ne placez pas l’appareil
dans un endroit avant de vous assurer qu’il y ait
une bonne circulation d’air.
18. N’enfoncez jamais d’objets à travers les ouvertures
de cet appareil, car ils pourraient entrer en
contact avec des points de tension dangereux ou
causer des courts-circuits qui peuvent dégénérer
en incendies ou en risques d’électrocution. Ne
renversez jamais de liquide dans ce produit.
19. Afin de réduire les risques d’électrocution, ne
démontez pas cet appareil, mais apportez-le dans
un centre de service autorisé. L’ouverture du
boîtier ou le retrait de toutes pièces que contient
cet appareil, à l’exception de l’accès autorisé à
certaines portes ou ouvertures, risque de vous
exposer à des points de tension dangereux ou
d’autres dangers. Un remontage incorrect peut par
la suite présenter des risques d’électrocution.
20. Vous devriez tester la réception chaque fois que
vous mettez l’appareil en fonction.
21. Examinez les composantes afin de vérifier si
celles-ci ne sont pas endommagées.
22. Soyez avisé de la perte de la confidentialité
lorsque vous utilisez les ondes publiques. Les
conversations peuvent être entendues par d’autres
moniteurs de bébé, des téléphones sans fil, des
scanneurs, etc.
23. Les enfants devraient être supervisés afin de vous
assurer qu’ils ne jouent pas avec l’appareil.
24. Le produit n’est pas conçu pour être utilisé par des
personnes (incluant des enfants) aux capacités
physiques, sensorielles ou mentales réduites ou
qui manquent d’expérience et de connaissances,
à moins qu’on leur ait donné suffisamment
de supervision ou d’instructions relativement
à l’utilisation de l’appareil par une personne
responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une température
entre 0˚ C (32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des
chaleurs extrêmes, ainsi qu’à la lumière directe
du soleil. Ne l’installez pas près d’une source de
chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur
excessive telle que la lumière du soleil ou au feu.
4. Assurez-vous que le moniteur
et le cordon de l’adaptateur sont
toujours hors de portée des
enfants, à au moins 1 mètre (3
pieds) de l’enfant ou du berceau,
pour éviter tout risque de
strangulation.
5. Ne jamais placer le moniteur à l’intérieur du
berceau ou du parc de bébé. Ne jamais couvrir le
moniteur ou l’unité (s) portative avec un article tel
une serviette ou une couverture.
6. D’autres équipements électroniques peuvent
produire des interférences sur votre moniteur vidéo
et audio. Tentez d’installer votre moniteur vidéo
ou audio à l’écart des appareils électroniques
tels que des routeurs sans fil, radios, téléphones
cellulaires, interphones, moniteurs, téléphones,
ordinateurs personnels, électroménagers et
téléphones sans fil.
Important safety
instructions
When using your equipment, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock and injury,
including the following:
1. Follow all warnings and instructions marked
on the product.
2. Adult setup is required.
3. This product is intended as an aid. It is not
a substitute for responsible and proper adult
supervision and should not be used as such.
4. This product is not intended for use as a
medical monitor.
5. Do not use this product near water. For
example, do not use it next to a bath tub, wash
bowl, kitchen sink, laundry tub or swimming
pool, or in a wet basement or shower.
6. CAUTION: Use only the batteries indicated in
this manual. There may be a risk of explosion
if a wrong type of battery is used for the parent
unit. Use only the supplied rechargeable battery
or replacement battery pack (BT166342/
BT266342) for the parent unit. Do not dispose
of batteries in a fire. They may explode. Dispose
of used battery according to the information in
The RBRC® seal.
7. Use only the adapters included with this
product. Incorrect adapter polarity or voltage
can seriously damage the product.
Baby unit power adapter: Output: 6V DC
400mA; Parent unit power adapter: Output:
6V DC 400mA.
8. The power adapters are intended to be
correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold
the plug in place if it is plugged into a ceiling,
under-the-table or cabinet outlet.
9. For pluggable equipment, the socket-outlet
shall be installed near the equipment and
shall be easily accessible.
10.Unplug this product from the wall outlet
before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.
11.Unplug the power cords before replacing
batteries.
12.Do not cut off the power adapters to replace
them with other plugs, as this causes a
hazardous situation.
13.Do not allow anything to rest on the power
cords. Do not install this product where the
cords may be walked on or crimped.
Stimulateurs cardiaques implantés dans
l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux
dispositifs numériques sans fil):
L’organisme ‘Wireless Technology Research, LLC
(WTR)’, une firme de recherche indépendante,
a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil portatifs
et les stimulateurs cardiaques implantés dans
l’organisme. Appuyée par l’Administration des
aliments et drogues (FDA) des États-Unis, la firme
WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
•
Vous devriez maintenir les dispositifs sans fil à au
moins six pouces du simulateur cardiaque.
•
Ils ne doivent PAS placer le téléphone sans fil
directement sur le stimulateur cardiaque, tel que
dans une poche de chemise, lorsque celui-ci est
en marche.
L’étude effectuée par l’organisme WRS n’a pas
identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent dispositifs
sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes
se rapportant aux champs électromagnétiques (EMF)
standard. Si vous le manipulez correctement en
suivant les instructions de ce guide, son utilisation
sera sécuritaire pendant de nombreuses années,
selon les meilleures évidences scientifiques dont nous
disposons aujourd’hui.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to
the holder of a valid proof of purchase (“Consumer” or
“you”) that the Product and all accessories provided in
the sales package (“Product”) are free from defects in
material and workmanship, pursuant to the following
terms and conditions, when installed and used
normally and in accordance with the Product operating
instructions. This limited warranty extends only to the
Consumer for Products purchased and used in the
United States of America and Canada.
What will VTech do if the Product is not free from
defects in materials and workmanship during
the limited warranty period (“Materially Defective
Product”)?
During the limited warranty period, VTech’s authorized
service representative will repair or replace at
VTech’s option, without charge, a Materially Defective
Product. If we repair the Product, we may use new
14.This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply in your home, consult your
dealer or local power company.
15.Do not overload wall outlets or use an
extension cord.
16.Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
17.This product should not be placed in any
area where proper ventilation is not provided.
Slots and openings in the back or bottom
of this product are provided for ventilation.
To protect them from overheating, these
openings must not be blocked by placing the
product on a soft surface such as a bed, sofa
or rug. This product should never be placed
near or over a radiator or heat register.
18.Never push objects of any kind into this
product through the slots because they may
touch dangerous voltage points or create a
short circuit. Never spill liquid of any kind on
the product.
19.To reduce the risk of electric shock, do
not disassemble this product, but take it to
an authorized service facility. Opening or
removing parts of the product other than
specified access doors may expose you to
dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when
the product is subsequently used.
20.You should test the sound reception every
time you turn on the units or move one of the
components.
21.Periodically examine all components
for damage.
22.Be aware of possible loss of privacy while
using public airwaves. Conversations may be
picked up by other nursery monitors, cordless
phones, scanners, etc.
23.Children should be supervised to ensure that
they do not play with the product.
24.The product is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
or refurbished replacement parts. If we choose to
replace the Product, we may replace it with a new or
refurbished Product of the same or similar design.
We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s
option, is your exclusive remedy. VTech will return the
repaired or replacement Products to you in working
condition. You should expect the repair or replacement
to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If VTech
repairs or replaces a Materially Defective Product under
the terms of this limited warranty, this limited warranty
also applies to the repaired or replacement Product for
a period of either (a) 90 days from the date the repaired
or replacement Product is shipped to you or (b) the time
remaining on the original one-year warranty; whichever
is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse,
accident, shipping or other physical damage,
improper installation, abnormal operation or
handling, neglect, inundation, fire, water or other
liquid intrusion; or
2. Product that has been damaged due to repair,
alteration or modification by anyone other than an
authorized service representative of VTech; or
3. Product to the extent that the problem experienced
is caused by signal conditions, network reliability, or
cable or antenna systems; or
4. Product to the extent that the problem is caused by
use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product
serial number plates or electronic serial numbers
have been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for
repair from outside the United States of America
or Canada, or used for commercial or institutional
purposes (including but not limited to Products
used for rental purposes); or
7. Product returned without a valid proof of purchase
(see item 2 on the next page); or
8. Charges for installation or set up, adjustment of
customer controls, and installation or repair of
systems outside the unit.
Cautions
1. Use and store the product at a temperature
between 32oF and 104oF.
2. Do not expose the product to extreme cold,
heat or direct sunlight. Do not put the product
close to a heating source.
3. Batteries should not be exposed to excessive
heat such as bright sunshine or fire.
4. Make sure the baby unit and
the adapter cord are always
out of reach of the baby, at
least 3 feet away from the baby
or crib, to avoid a possible
strangulation hazard.
5. Never place the baby unit inside the baby’s
crib or playpen. Never cover the baby unit or
parent unit with anything such as a towel or
a blanket.
6. Other electronic products may cause
interference with your baby monitor. Try
installing your baby monitor as far away
from these electronic devices as possible:
wireless routers, radios, cellular telephones,
intercoms, room monitors, televisions,
personal computers, kitchen appliances and
cordless telephones.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital
cordless devices):
Wireless Technology Research, LLC (WTR),
an independent research entity, led a
multidisciplinary evaluation of the interference
between portable wireless devices and
implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR
recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six
inches from the pacemaker.
• Should NOT place wireless devices directly
over the pacemaker, such as in a breast
pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to
bystanders with pacemakers from other persons
using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this
user’s manual, the product is safe to be used based
on scientific evidence available today.
and are responsible for delivery or handling charges
incurred in the transport of the Product(s) to the
service location. VTech will return repaired or replaced
Product under this limited warranty. Transportation,
delivery or handling charges are prepaid. VTech
assumes no risk for damage or loss of the Product
in transit. If the Product failure is not covered by this
limited warranty, or proof of purchase does not meet
the terms of this limited warranty, VTech will notify you
and will request that you authorize the cost of repair
prior to any further repair activity. You must pay for
the cost of repair and return shipping costs for the
repair of Products that are not covered by this limited
warranty.
What must you return with the Product to get
warranty service?
1. Return the entire original package and contents
including the Product to the VTech service location
along with a description of the malfunction or
difficulty; and
2. Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model)
and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing
address, and telephone number.
The RBRC® program provides a convenient alternative
to placing used nickel-metal batteries into the trash or
municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to
drop off the spent battery at local retailers participating
in the RBRC® program or at authorized VTech product
service centers. Please call 1 (800) 8 BATTERY® for
information on Ni-MH battery recycling and disposal
bans/restrictions in your area. VTech’s involvement in
this program is part of its commitment to protecting our
environment and conserving natural resources.
RBRC® and 1 (800) 8 BATTERY®
are registered trademarks of
Rechargeable Battery Recycling
Corporation.
FCC and IC regulations
FCC Part 15
This equipment has been tested and found to comply
with the requirements for a Class B digital device under
Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
7HFKQLFDOVSHFLÀFDWLRQV
Frequency
control
Transmit
frequency
Crystal controlled PLL synthesizer
Baby unit: 1921.536-1928.448 MHz
Parent unit: 1921.536-1928.448 MHz
Channels
LCD
35 (x) x 21.2 (y) mm B&W LCD
Nominal
effective
range
Maximum power allowed by FCC
and IC. Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirement
Parent unit: 2.4 V Ni-MH battery
Baby unit power adapter:
Output: 6V DC 400mA
Parent unit power adapter:
Output: 6V DC 400mA
This warranty is the complete and exclusive
agreement between you and VTech. It supersedes
all other written or oral communications related to this
Product. VTech provides no other warranties for this
Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There
are no other express warranties. No one is authorized
to make modifications to this limited warranty and you
should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you
specific legal rights, and you may also have other rights,
which vary from state to state or province to province.
NOTE: Before calling for service, please review the
user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume the
risk of loss or damage during transit and transportation
Please retain your original sales receipt as proof
of purchase.
To obtain warranty service in the USA, please visit our
website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or call 1 (800) 267-7377.
The RBRC® seal on the nickel-metal battery indicates
that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and
recycle these batteries at the end of their useful lives,
when taken out of service within the United States and
Canada.
Other limitations
Limitations: Implied warranties, including those of
fitness for a particular purpose and merchantability (an
unwritten warranty that the Product is fit for ordinary
use) are limited to one year from the date of purchase.
Some states/provinces do not allow limitations on
how long an implied warranty lasts, so the above
limitation may not apply to you. In no event shall
VTech be liable for any indirect, special, incidental,
consequential, or similar damages (including, but
not limited to lost profits or revenue, inability to use
the Product or other associated equipment, the cost
of substitute equipment, and claims by third parties)
resulting from the use of this Product. Some states/
provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
How do you get warranty service?
The RBRC® seal
Specifications are subject to change without notice.
© 2017 VTech Communications, Inc.
All rights reserved. 03/17. DM226_CIB_V1.0
Document order number: 91-010503-020-100

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:fdc70dc7-07a6-11e7-0000-759962ce4a9f
Producer                        : GPL Ghostscript 9.07
Keywords                        : ()
Modify Date                     : 2017:03:10 12:38:43+08:00
Create Date                     : 2017:03:10 12:38:43+08:00
Creator Tool                    : PDFCreator Version 1.7.1
Document ID                     : uuid:fdc70dc7-07a6-11e7-0000-759962ce4a9f
Format                          : application/pdf
Title                           : -DM226_CIB_V1_20170303.pdf
Creator                         : stanleyl
Description                     : ()
Author                          : stanleyl
Subject                         : 
EXIF Metadata provided by EXIF.tools
FCC ID Filing: EW780-9982-01

Navigation menu