Valeo Comfort and Driving Assistance A08TAA A08TAA, A08TAB User Manual A08TAA Owner Manual rev
Valeo Comfort and Driving Assistance A08TAA, A08TAB A08TAA Owner Manual rev
Owner Manual
Valeo Sécurité Habitacle
Product Group Interior Electronics
Business Group Comfort & Driving Assistance
[1/5]
Owner Manual (draft)
Model: Transmitter (CD4 IKT)
Model No.: A08TAA, A08TAB
FCC ID: N5F-A08TAA
IC: 3248A-A08TAA
(preliminary draft, some change may appear in the final version)
[2/5]
Remote Keyless Entry
Lock button
UnLock button
Trunk opening
button
Panic button
- Botton view -
- Top view -
Car Maker logo (brand)
Model A08TA
Model A08TAModel A08TA
Model A08TAB
BB
B
(4 buttons)
Model A08TA
Model A08TAModel A08TA
Model A08TAA
AA
A
(3 buttons)
[3/5]
1.
OPERATION
LOCK
Press this button once to lock all doors. Some exterior lights will flash once (to be confirmed).
Doors can not be locked if any door is not fully closed or the key is in the ignition switch.
UNLOCK
Press this button once to unlock the driver’s door. Push it twice to unlock the other doors. Some
exterior lights will flash twice (to be confirmed) each time you press the button.
This button does not work when the key is in the ignition switch.
TRUNK RELEASE (on certain version)
Press this button for about 1 second (to be confirmed) to release the trunk. Trunk can not be opened
if the key is in the ignition switch.
PANIC
Press this button for about 1 second (to be confirmed) to attract attention;the horn will sound, and the
exterior lights will flash for about 30 seconds (to be confirmed). To cancel panic mode, press any other
button on the remote transmitter, or insert the key.
2. TRANSMITTER CARE
♦ Avoid dropping or throwing the transmitter.
♦ Protect the transmitter from extreme temperature.
♦ Do not immerse the transmitter in any liquid.
♦ If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
[4/5]
3. BATTERY REPLACEMENT
The battery is not rechargeable. To replace the battery:
①
Push the button on the transmitter to extend the key blade.
② Remove the battery cover by prying it with a finger. Note the polarity.
③ Remove the battery by pushing on the battery and sliding it toward the key blade.
④
Insert the new battery, positive side facing up. Push the battery down until it is held in place.
Replace with a CR2032 or equivalent battery.
⑤ Snap the battery cover back on to the transmitter
Avoid touching the new batteries with your fingers.
Do not touch the printed circuit board or the PCB battery holder
[5/5]
REGULATORY INFORMATION
For USA & Canada
FCC ID: N5F-A08TAA
IC: 3248A-A08TAA
English:
This device complies with Part 15 of the FCC Rules and with Industry Canada
licence-exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTICE:
Changes or modifications made to this equipment not expressly approved by other
than an authorized service facility may void the FCC authorization to operate this
equipment.
Français:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.