Vantage Controls 22713 902-928 MHz transceiver module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3440145
Application ID	KQrWdAdIdHWdRjSbJtMq2g==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	29.56kB (369558 bits)
Date Submitted	2017-06-26 00:00:00
Date Available	2017-06-26 00:00:00
Creation Date	2017-06-22 10:07:46
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2017-06-22 12:03:09
Document Title	User Manual
Document Creator	Microsoft® Office Word 2007
Document Author:	jaredl

ETII RF
OEM/Integrators Installation Manual
900 MHz RadioLink Control Board Module
The module is limited to OEM installation ONLY
Vantage Controls
2168 W Grove Parkway, Ste 300
Pleasant Grove, UT 84062
(801) 229-2800
June 22, 2017
FCC Compliance Information
FCC ID: PII-22713
IC: 3505A-22713
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC Compliance Warning:
Changes or modifications to this product not expressly approved by Vantage Controls could void the
user’s authority to operate this product.
**All information on this page “FCC Compliance Information” shall be supplied to the end user
of any product the ETII RF is incorporated into.
IC Compliance Information
IC: 3505A-22713
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
IC Notice (Avis D'Industrie Canada)
PRUDENCE: Changements ou modifications pourraient annuler le droit de l'utilisateur à utiliser l'équipement non autorisées.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un
gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes:
1.
2.
l’appareil ne doit pas produire de brouillage, et
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle.
Cet équipement génère, utilise et peut émettre une énergie de radiofréquence et, s'il n'est pas installé et utilisé conformément a ux
instructions, il peut causer des interférences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des
interférences no se produiront pas dans une installation particulière. Si cet équipement provoque des interférences nuisibles à la
réception radio ou télévision, ce qui peut être déterminé en mettant l'équipement hors et sous tension, l'utilisateur est encouragé à
essayer de corriger l'interférence par une ou plusieurs des mesures suivantes:




Réorienter ou déplacer l'antenne de réception.
Augmentez la distance entre l'équipement et le récepteur.
Connecter l'équipement à une sortie sur un circuit différent de celui sur lequel le récepteur est branché.
Consulter le revendeur ou un technicien radio / télévision expérimenté pour de l'aide.
Introduction
The ETII RF is an RF Control Board Module that contains a microcontroller and a RF
transceiver chip. It is designed to be incorporated into control devices developed by Vantage
Controls. The module operates under FCC approval in the 902-928 MHz ISM frequency band.
The module is limited to OEM installations only.
The module is limited to installation in mobile or fixed applications.
Integrating the ETII RF module into Products
The OEM is responsible that the end user has no manual or instructions to remove or install the
module.
IMPORTANT: The ETII RF radio has been certified by the FCC as a module for integration into
products without further certification being necessary (as per FCC section 2.1091.) The following
requirements must be satisfied in order to comply with FCC regulations:
1) The OEM/Integrator must ensure that final produce has a label, as shown below, placed
on the outside of the device.
2) The ETII RF module may only be used with the antenna that has been tested and
certified.
IMPORTANT: Separate approval is required for all other operating configurations, including portable
configurations with respect to Part 2.1093 and different antenna configurations.
IMPORTANT: Final products must be tested to comply with unintentional radiators (FCC section
15.107 & 15.109) before the OEM can declare compliance of their final product to Part 15 of the FCC
Rules. Testing for compliance must be performed with the module installed in the end-product.
We hereby acknowledge our responsibility to provide guidance to the host manufacturer in the event
that they require assistance for ensuring compliance with the Part 15 Subpart B requirements.
FCC RF Exposure requirement
In order to comply with the FCC RF exposure requirements, the ETII RF may be used only
with the antenna that has been tested and certified. The certified antenna is located on the module
and has a permanent connection to the ET II RF Module:
Manufacturer
Model #
Type
Gain(dBi)
Ethertronics
M620720
Chip
2.6
Minimum
Cable Length
N/A
A minimum separation distance of 20 cm must be maintained from the antenna to any nearby
persons.
Interface Pins:
Pin #
10
11
12
Description
DIO to Microcontroller
Power
DIO to Microcontroller
Ground
DIO to Microcontroller
DIO to Microcontroller
DIO to Microcontroller
DIO to Microcontroller
DIO to Microcontroller
DIO to Microcontroller
DIO to Microcontroller
DIO to Microcontroller
Connections marked “DIO to Microcontroller” are used for control of external circuits. This allows the
RF control board module to be combined with various lighting control circuits on an external PCB
such as Triac Dimmers, FET Dimmers and Relays. The external PCB is independent from the RF
Module and has no direct impact on the radio communication.
RF Exposure / Final Configuration
In order to comply with Part 15.212(a)(vii), “The modular transmitter must comply with any applicable
RF exposure requirements in its final configuration”. The ET II RF Module will only be used in
products that Vantage Controls has designed and tested to ensure that they meet the RF exposure
requirements.
Specifications
Model #: ........................................................................................... ETII RF
Frequency Range .................................................. 902-928 MHz ISM Band
Power Supply ................................................................................. 5-9 VDC
Current required while transmitting ................................................... 150mA
Current required while receiving ......................................................... 70mA
Antenna Gain................................................................................... ~2.6dBi
Transmit Power ...................................................................32mW (15dBm)
RF Communications Technology......Frequency Hopping Spread Spectrum
Number of Hop Channels .........................................................................25
RF Data Rate.............................................................................. 19,200 bps
Interface Data Rates ........................................................... 9600-54600 bps
Size ......................................................................................... 1.375” x 2.5”
Operating Temperature Range ...................................................... -40-70°C

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : jaredl
Create Date                     : 2017:06:22 10:07:46-06:00
Modify Date                     : 2017:06:22 12:03:09-06:00
Language                        : en-GB
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Format                          : application/pdf
Creator                         : jaredl
Creator Tool                    : Microsoft® Office Word 2007
Metadata Date                   : 2017:06:22 12:03:09-06:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:a2451a64-d391-4657-bb95-be969eede7c4
Instance ID                     : uuid:56072eae-5f19-4d79-8798-c3cec2144456
Page Count                      : 6

EXIF Metadata provided by EXIF.tools