Veebeam RC2-SC4402R RC2 Model WUSB Mini Card Module User Manual WUSB Mini Card Data sheet

Veebeam Limited RC2 Model WUSB Mini Card Module WUSB Mini Card Data sheet

Users Manual

            RC2 Full Mini Card ODM Manual  Rev 1.0      Page 1 of 9 Strictly Company Confidential The information in this document is proprietary to Veebeam Corporation. It is not to be partially or wholly reproduced or disclosed to any third party without the prior permission of Veebeam Corporation.                 SC4402R-C Mini Card User manual for ODM manufacturers
            RC2 Full Mini Card ODM Manual  Rev 1.0      Page 2 of 9 Strictly Company Confidential The information in this document is proprietary to Veebeam Corporation. It is not to be partially or wholly reproduced or disclosed to any third party without the prior permission of Veebeam Corporation.    Contents 1 INTRODUCTION .................................................................................................................................3 1.1 OBJECTIVE ...................................................................................................................................... 3 1.2 SCOPE .............................................................................................................................................. 3 2 MINI CARD OVERVIEW ...................................................................................................................4 2.1 FORM FACTOR ................................................................................................................................ 4 2.2 MINI CARD DELIVERABLES............................................................................................................ 4 2.3 MINI CARD INSTALLATION............................................................................................................. 5 2.4 FCC LOGO PLACEMENT ................................................................................................................. 5 2.5 ATTESTATION STATEMENT............................................................................................................. 5 3 MINI CARD SPECIFICATION ..........................................................................................................6 3.1 RF SPECIFICATION ......................................................................................................................... 6 3.2 POWER SUPPLY REQUIREMENT ...................................................................................................... 8 3.3 DIGITAL INTERFACES ..................................................................................................................... 8 3.4 USB ................................................................................................................................................. 8 3.5 PCI EXPRESS................................................................................................................................... 8 3.6 UART.............................................................................................................................................. 8 3.7 GPIO ALLOCATIONS ...................................................................................................................... 8 4 MECHANICAL .....................................................................................................................................9 4.2 CERTIFICATION............................................................................................................................... 9 4.3 ENVIRONMENTAL LIMITS............................................................................................................... 9  Figure 1 – Mini Card......................................................................................................................... 4
            RC2 Full Mini Card ODM Manual  Rev 1.0      Page 3 of 9 Strictly Company Confidential The information in this document is proprietary to Veebeam Corporation. It is not to be partially or wholly reproduced or disclosed to any third party without the prior permission of Veebeam Corporation.   1  Introduction 1.1  Objective This  document  details  the  hardware  specification  for  the  RC2  based  Full  Mini  Card  which  will support  operation  on  BG1  for  the  US  region  using  a  High  Pass  filter  and  external antenna  and installation guide for ODM manufacturers.    The Mini Card is designed to be incorporated into WUSB video receiver products. 1.2  Scope This document defines the electrical and mechanical specifications.
            RC2 Full Mini Card ODM Manual  Rev 1.0      Page 4 of 9 Strictly Company Confidential The information in this document is proprietary to Veebeam Corporation. It is not to be partially or wholly reproduced or disclosed to any third party without the prior permission of Veebeam Corporation.   2  Mini Card Overview 2.1  Form Factor The proposed form factor for the Mini card RDK is shown in figure 1, below. The width and the length  of  the  PCB  are  30mm  and  50.95  mm  respectively.  The  PCB  will  be  1.0mm  thick.  The maximum component height on the top and bottom side of the board will not exceed 2.4mm and 1.35mm respectively.  A footprint will be provided on the PCB top side to fit a one piece metal shielding can to enclose all components that are potential sources of secondary emissions and to meet the relevant radio specifications.  This will also aid heat dissipation by the  use of a thermal  pad between RC2 and the shield. The PCB will be made from UL94V-0 approved materials and be marked accordingly.         Figure 1 – Mini Card 2.2  Mini Card Deliverables The Otter Mini Card is designed to provide ODMs with a complete package of information to allow them to quickly develop and test the Mini Card with the minimum of specialist skills, design time and effort.  The following information will be delivered to ODMs for manufacture: •  RC2 data sheet •  Orcad schematics •  PADS PCB design files •  PCB stackup information •  BOM in Excel format •  PDF schematics •  GERBER files for 1up PCB •  Assembly drawings •  Design Guidelines •  Relevant certification documents
            RC2 Full Mini Card ODM Manual  Rev 1.0      Page 5 of 9 Strictly Company Confidential The information in this document is proprietary to Veebeam Corporation. It is not to be partially or wholly reproduced or disclosed to any third party without the prior permission of Veebeam Corporation.   2.3  Mini Card Installation The  PCB  will  comply  with  the  mechanical  requirements  of  the  PCI  Express®  Mini  Card Electromechanical  Specification  Revision  1.2  [6],  card  type  F1  (Full-Mini  without  bottom-side keep-outs)  so that  it can  be slotted  into the  PCI  connector  on the WUSB video  receiver mother board and secured. 2.4  FCC Logo placement FCC Logo and FCC ID labels, as defined in § 15.19, must be placed on the mini card module and also on the enclosure of the final WUSB video product.  Labelling of any end product is required to prominently display the any associated FCC ID.  The following is a suggested, example label for an end product: Contains FCC ID: UQL-RC2-SC4402R  2.5  Attestation statement Veebeam Corporation (OEM) will ensure the necessary attestation statements are included in the final product user manual. An example is given below.
            RC2 Full Mini Card ODM Manual  Rev 1.0      Page 6 of 9 Strictly Company Confidential The information in this document is proprietary to Veebeam Corporation. It is not to be partially or wholly reproduced or disclosed to any third party without the prior permission of Veebeam Corporation.   3  Mini Card Specification The Mini Card is designed specifically for use in the WUSB video receivers and will support BG1 operation using a high pass filter.  Note:  WUSB video receivers (powered by a AC mains adaptor) with video outputs to connect to a TV set.  Hence, conforms to FCC part 15.517(a). 3.1  RF Specification The mini card is designed to meet the following requirements. 3.1.1  Frequency Band Mini card is designed to operate in the 3100MHz to 4800MHz frequency band (WiMedia BG1). 3.1.2  Operational Bandwidth Mini  card  is  designed  to  support  the  OBW  requirements  defined  in  15.503(a)  of  the  FCC specification 3.1.3  Transmit Power Transmit power: ≤ -41.3dBm/MHz (ensured through mini card firmware and can not be altered by the end user). 3.1.4  Transmit Signal Quality Mini  card  is  designed  to  meet  the  EVM  requirements  defined  in  the  WiMedia  specification,  as follows. Data Rate (Mbps)  Transmit EVM 53.3, 80, 106.7, 160, 200  -15.5dB 320, 400, 480  -18dB 3.1.5  Transmit power spectral density The transmitted spectral mask shall have the following break points: an emissions level of 0 dBr (dB relative to the maximum spectral density of the signal) from -260 MHz to 260 MHz around the center frequency, -12 dBr at 285 MHz frequency offset, and -20 dBr at 330 MHz frequency offset and above. For all other intermediate frequencies, the emissions level is assumed to be linear in the dB scale. The transmitted spectral density of the transmitted signal shall fall within the spectral mask, as shown in Figure below.
            RC2 Full Mini Card ODM Manual  Rev 1.0      Page 7 of 9 Strictly Company Confidential The information in this document is proprietary to Veebeam Corporation. It is not to be partially or wholly reproduced or disclosed to any third party without the prior permission of Veebeam Corporation.   3.1.6  Transmit Center Frequency Tolerance The transmitted center frequency tolerance shall be ±20 ppm maximum. 3.1.7  Symbol Clock Frequency Tolerance The symbol clock frequency tolerance shall be ±20 ppm maximum. 3.1.8  Receiver Sensitivity Mini card design includes an LNA in the receive path (using two Tx/Rx switches) to improve the radio range and meets the following receiver sensitivity specification. Data rate (Mb/s)  Minimum Receiver Sensitivity (dBm) 53.3  -84.8 80  -82.9 106.7  -81.8 160  -79.9 200  -78.5 320  -76.8 400  -75.5 480  -74.0  3.1.9  Mini card Emissions Mini card is designed to meet the FCC 15.517& 15.209 specifications. 3.1.10   Rx Immunity The  data  throughput  on  a  channel  shall  not  degrade  by  >10%  in  the  presence  of  standard consumer interference sources when operated with >1m separation. 3.1.11  Antenna The Mini Card is fitted with a UFL connector for the ODM manufacturer to assemble the following antenna part. Antenna: Acon antenna ADM6P-700042  Once assembled, both antenna and the antenna port must be inaccessible to the end user in the final product. This is to prevent the end user from using a higher gain or directional antennas.
            RC2 Full Mini Card ODM Manual  Rev 1.0      Page 8 of 9 Strictly Company Confidential The information in this document is proprietary to Veebeam Corporation. It is not to be partially or wholly reproduced or disclosed to any third party without the prior permission of Veebeam Corporation.   3.2  Power supply requirement Mini card designed to be incorporated into the WUSB video receiver will be powered by a 3.3V ± 5% supply through PCI connector from the WUSB video receiver mother board.  Note: The WUSB video receiver is powered by an AC – 12V wall adaptor.   3.3  Digital Interfaces The card will support USB & PCIe interfaces. 3.4  USB The USB interface will be connected to the applications processor on the main board and serve as the main data path. The Mini Card shall be capable of continuous operation at the following speeds. 1.  Full Speed (12Mbps) 2.  High Speed (480Mbps) 3.5  PCI Express The Mini Card will be electrically compatible with the pin assignments for mini PCIe connectors. It will support the data signalling requirements but the control & power management features of PCI Express will not be implemented.  3.6  UART The RC2 UART connections are brought out using the PCIe SMBUS connections.  3.7  GPIO Allocations GPIO allocations are as detailed in the schematics. 3.7.1  Initial Programming There are 2 options available for Mini card programming: •  Devices are programmed prior to assembly. (minimum quantities would apply) •  Devices are programmed after assembly using the Production Test Fixture
            RC2 Full Mini Card ODM Manual  Rev 1.0      Page 9 of 9 Strictly Company Confidential The information in this document is proprietary to Veebeam Corporation. It is not to be partially or wholly reproduced or disclosed to any third party without the prior permission of Veebeam Corporation.   4  Mechanical 4.1.1   RF Shield Provision  will  be  made  to  fit  a  rectangular  metal  screen.  The  Mini  Card  shall  be  designed  to minimise  the  RC2  temperature  by  maximising  copper  flood  around  RC2  and  on  all  inner  PCB layers. Good thermal connection to the RF screen will be accomplished using Gap pad or similar material attached to the top of RC2. 4.2  Certification Certification  is  a  mandatory  requirement  for  UWB  products.  The  certification  process  is  quite involved and requires specialist knowledge. Not all customers will have the resources necessary to  achieve  certification.  Therefore  Veebeam  Corporation  will  undertake  certification  of  the  Mini Card  and  deliver  a  complete  package  of  information  which  will  enable  ODMs  to  design  and manufacturer certifiable products. These reports will be made available to ODMs on request. The Mini Card will be certifiable to the following standards: •  RF Certifications  - FCC  BG1 •  WiMedia ( achieved at WiMedia Interop events ) •  CWUSB ( achieved at Intel Labs ) •  USB 2.0 Electrical and Functional 4.3  Environmental Limits •  Operational temperature range shall be from 0ºC to 55ºC. (Based on a 15degC temp rise inside the Motherboard enclosure which is specified to operate from 0ºC to 40ºC external). •  Storage temperature limits shall be -40ºC to +100ºC. •  RC2 Mini Card characterised over 0ºC to +70ºC.

Navigation menu