Vencer BTVM1000 WIRELESS MOUSE User Manual Quick Guide VM 1000

Vencer Co., Ltd. WIRELESS MOUSE Quick Guide VM 1000

USERS MANUAL

BBlluueettooootthh MMoouussee VVMM--11000000 20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C. Tel. No.:+886-2-2698-3608 Fax No.:+886-2-2698-3648 Apr.07”2008 V1.0 1/4 BBuuttttoonn FFuunnccttiioonn :: FCC ID: VHVBTVM1000
BBlluueettooootthh MMoouussee VVMM--11000000 20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C. Tel. No.:+886-2-2698-3608 Fax No.:+886-2-2698-3648 Apr.07”2008 V1.0 2/4 FCC ID: VHVBTVM1000
BBlluueettooootthh MMoouussee VVMM--11000000 20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C. Tel. No.:+886-2-2698-3608 Fax No.:+886-2-2698-3648 Apr.07”2008 V1.0 3/4 QQuuiicckk SSttaarrtt 1. Power On/Off Sliding power switch at bottom of mouse to turn on/off VM-1000. 2. Pairing Press Connect button, and then Blue LED light on at sensor hole. Now, VM-1000 is under pairing mode. Step 1. Set VM-1000 under pairing mode Step 2. Follow the pairing process of PC to search & pair with VM-1000 Step 3. After pairing is complete, VM-1000 will connect automatically. When VM-1000 is connected, Blue LED will off. 3. Connect To press any key or move mouse to connect to the paired PC when Bluetooth link is disconnect. 4. Auto Disconnect/Power Off VP-1000 will auto disconnect with PC, if no any action for a while. 5. Function Keys 1. CPI button : You can change the mouse resolution by press CPI button. VM-1000 supported 400,800,1200 & 1600 CPI. The LED indicator will show different length to indicate the CPI when you press CPI select button. 2. Page up, Page down : To press Page up/down button to change page of document when you are doing presentation. FCC ID: VHVBTVM1000
BBlluueettooootthh MMoouussee VVMM--11000000 20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C. Tel. No.:+886-2-2698-3608 Fax No.:+886-2-2698-3648 Apr.07”2008 V1.0 4/4 6. LED indicator There are 5pcs of LED to indicate the battery capacity when power on. The 5pcs of LED will scrolling when charging. The 5pcs of LED will show different length to indicate the CPI you selected when press CPI select button 7. Low Battery If the LED indicator only light on 1pc LED, it means low battery. Please plug charging cable/adaptor to charge battery. 8. Charge Battery The 5pcs of LED will scrolling when battery is charging. All LED light on and stop scrolling when battery is fully charge. FCC ID: VHVBTVM1000
FCC ID: VHVBTVM1000 FCC Compliance and Advisory Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.Reorient the receiving antenna. 2.Increase the separation between the equipment and receiver. 3.Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. 4.Consult the dealer or an experienced radio/TV technician for help. Any special accessories needed for compliance must be specified in the instruction manual. Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment. CAUSION: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Navigation menu