Venture Global DWS-200 Driveway Alert Sensor User Manual 2
Venture Global Limited Driveway Alert Sensor 2
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2428504 |
| Application ID | BEZvbIbp87y/rU5gL08NxA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 44.29kB (553671 bits) |
| Date Submitted | 2014-10-27 00:00:00 |
| Date Available | 2014-10-27 00:00:00 |
| Creation Date | 2013-10-15 13:40:54 |
| Producing Software | Corel PDF Engine Version 16.1.0.843 |
| Document Lastmod | 2013-10-15 13:40:54 |
| Document Title | 無標題-2 |
| Document Creator | CorelDRAW X6 |
| Document Author: | Lowes Lo |
USER MANUAL Key Function On Receiver Power On/Off Volume Pause/Reset Melody/Batt.Chk DC jack Learn/Next Battery Cover Cable come out from Relay Power on/off : To switch on or switch off the receiver using this switch. Volume: To adjust the volume level by rotating volume DC jack: The AC/DC adaptor plug to this jack Pause/Reset: Pause - Temporarily stop the receiver bypress and hold this button 3 sec. Reset - Clear the sound and light on the receiver by press this button once Melody / Batt. chk: See the chapter of learn and Check which sensor in battery low Learn/Next: See the chapter of learn and Check which sensor in battery low Bottom on Receiver Indications on Receiver AC Power on/ RX Batt. Low * AC Power Operate: Light up blur LED while using #4 Zone/ Sensor AC adaptor * Back up Battery Operate: Light red LED while operated by battery * RX Battery Low: Flashs red LED with 0.3 sec. On / 5 sec. Off and sounds "beep" every half minute * Remote Sensor Battery low: Flash red LED with 0.3 sec. On / 5 sec. Off and sound "beep" #3 Zone/ Sensor Power & Setting Remove the battery cover for setting the connection / time delay. Remote sensor battery low #1 Zone/ Sensor #2 Zone/ Sensor Although this receiver operate with AC/DC adaptor, we still need to install battery for backup. 12V out D. Delay time setting: These switch adjust the output time of the output terminal. E. 12V output control: To choose which zone connect to the 12V output. F. NC/NO output control: To choose which zone connect to NO/NC output. Off On B Pause Time Setting NO COM NC 30 min Pause mode EU US Delay time setting 1S AA AA AA AA 60 min 5S Slide to open the battery cover 10 S 60 S E 12V output control F NO/NC control A Output terminal: Connect to the device that you wanted control, such as Gate opener, Door release or external alarm speaker ..... --- 12V out : this terminal output 12v 300mA when the select zone has been trigger. (This terminal can not output 12V when using the backup battery.) This output cooperate with "E". you can select which zone relayed to this output by slide the DIP witch 1,2,3,4 on or off. --- NO (Normal Open): this terminal output short circuit when the select zone has been trigger. --- NC (Normal Close): this terminal output open circuit when the select zone has been trigger. The NO and NS outputs cooperate with "F". you can select which zone relayed to these output by slide the DIP witch 1,2,3,4 on or off. B. Pause timer setting: Select the pause time 30 min or 60 min C. Pause mode: EU mode: auto turn on when the pause time is over. US mode: the receiver generat a beep tone when the pause time is over. Adjust the dip switch as you need and Connect the wire to the device that you want to control Install the 4 AAA batteries into the battery compartment as the indication on the compartment Replace the battery cover The main power of this unit is 12V/500mA AC/DC adaptor FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Modifications to this product will void the user's authority to operate this equipment. Installation Switch inside the transmitter Mount the transmitter on the wall 1.5m from the ground and slightly toward the ground and point to the target sensing area. Remove the screw from the top cabinet. Battery compartment Interval Timer 30 sec 7 sec After detect an intrude the sensor will sleep 7 seconds or 30 seconds. Test Button Sensitivity Photo sensor On/Off Off 12m 8m Filter 1-2m/sec Mark the 4 hole on the wall using a pencil. 7m On 4m 0.5-1m/sec Battery Installation o/ 7mm 25mm AA AA AA AA Requires an electric drill for holes to fix the Sensor with the provided ram plug and screws. Install the 4 AA batteries into the battery compartment as the indication on the compartment Replace the cover and l ock screw Replace the sun blocker Adjust the sensor to make a good operation angle Learn (Pairing with remote sensor) 1. Press "learn" button and hold 3 second to entering to "learn mode" Battery low Receiver The "RX Batt. Low" LED (Red) will blink every 5 second and beep every 15 minute to indicate the backup batter low or no battery installed AC Power on (Blue)/ RX Batt. Low (Red) BatteryLowIndication Power ACPower Battery Normal Indication Battery Low Beepsound every LED Indication 30 minutes Blue NoBatteryinstalled 2. Press "learn" button to select the preferred zone Blue + Red Flash Blue + Red Flash Red Remote sensor battery low Red Flash Sensors The "Remote sensor battery Low" LED will blink every 5 second and beep every 30 minute to indicates sensor(s) batter low. Check which sensor in battery low 1. Press "Battery Check" button and hold 3 second to entering to "check mode". The sensor battery low LED will light up after enter the battery check mode. 2. Press "Next button" button to switch between the zones, light up Zone 1 first, Press again the "Next button" to switch zone 2 > zone 3 > zone4 If going to chk, zone 2. Press 2 time "next button" make the LED stop at Zone2 Melody select sequence Melody#1 >> Melody#2>> ....>>Melody#32 >> Melody#1 4. Trigger the sensor which going to be paired. * Sounds "Beep" whiled sussfully * If the Sensor paired with other Zone: there will not sound and show the Zone paired with the sensor for 3 sec., Then goes back to the selected Zone. * If all the space were occupied. 1,2,3,4 zone's LED flash 3 time. Pause mode: EU mode: auto turn on (Exit the pause mode) when the pause time is over. US mode: the receiver generat a beep tone when the pause time is over. Press the pause button to exit the pause mode BATT. LOW alert will not off until replace the battery. Code Conflict If the PIR sensor coding is the same as another transmitter you must change the code. When you have changed the code, you need to repair the PIR sensor. AA If you want to disable the system Temporary: 1. Choose the pause time (30 or 60 minutes) 2. Press "Pause" button and hold 3 second and release while the four zone LED lit. 3. The four zone LED will lit up in succession to indicate the receiver is in pause mode. The receiver will not receive any signal while the receiver is in pause mode 4. Press the pause button again to exit the pause mode. How to clearn the battery low signal AA How to Pause the system * Release "battery chk" button and press "Next" to check next zone. * zone 1 >> zone 2 >> zone 3 >> zone 4 >> exit the battery mode AA Clean all the sensor in a zone 1. Press "Learn: button and hold 3 second to enter "learn mode" 2. Press "next button" to select which zone going to unpair the sensors. 3. Press "Pause/Reset" button for 3 sec. To unpair all the sensors in the zone. 4. Press "Next button" untill exit the mode. Press and hold "battery chk" button The LED 1,2,3,4 will show which sensor/sensors are battery low. AA 3. After select the zone then press "melody" button to select the preferred melody for the sensor going to be paired Press and hold the test button, insert the battery and hold the button 5 seconds. The LED will flash 5 time when a new code is generated
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Profile CMM Type : Lino Profile Version : 2.1.0 Profile Class : Display Device Profile Color Space Data : RGB Profile Connection Space : XYZ Profile Date Time : 1998:02:09 06:49:00 Profile File Signature : acsp Primary Platform : Microsoft Corporation CMM Flags : Not Embedded, Independent Device Manufacturer : IEC Device Model : sRGB Device Attributes : Reflective, Glossy, Positive, Color Rendering Intent : Perceptual Connection Space Illuminant : 0.9642 1 0.82491 Profile Creator : HP Profile ID : 0 Profile Copyright : Copyright (c) 1998 Hewlett-Packard Company Profile Description : sRGB IEC61966-2.1 Media White Point : 0.95045 1 1.08905 Media Black Point : 0 0 0 Red Matrix Column : 0.43607 0.22249 0.01392 Green Matrix Column : 0.38515 0.71687 0.09708 Blue Matrix Column : 0.14307 0.06061 0.7141 Device Mfg Desc : IEC http://www.iec.ch Device Model Desc : IEC 61966-2.1 Default RGB colour space - sRGB Viewing Cond Desc : Reference Viewing Condition in IEC61966-2.1 Viewing Cond Illuminant : 19.6445 20.3718 16.8089 Viewing Cond Surround : 3.92889 4.07439 3.36179 Viewing Cond Illuminant Type : D50 Luminance : 76.03647 80 87.12462 Measurement Observer : CIE 1931 Measurement Backing : 0 0 0 Measurement Geometry : Unknown Measurement Flare : 0.999% Measurement Illuminant : D65 Technology : Cathode Ray Tube Display Red Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Green Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Blue Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Page Count : 3 Create Date : 2013:10:15 13:40:54+08:00 Modify Date : 2013:10:15 13:40:54+08:00 Producer : Corel PDF Engine Version 16.1.0.843 Author : Lowes Lo Creator : CorelDRAW X6 Title : 無標題-2EXIF Metadata provided by EXIF.tools