Vesper Marine VESPXB8010 XB-8010 Class B AIS Transponder with WLAN User Manual User guide

Vesper Marine Limited XB-8010 Class B AIS Transponder with WLAN User guide

Contents

User guide

XB-8000 | XB-6000 INSTALL GUIDE
OPTIONAL ACCESSORIESWHAT YOU NEED TO GET GOING = Item Included = Item Included CONNECTIONSSTATUS LEDCOLOR STATE DESCRIPTIONGreen (OK) Solid Normal OperationFlashing Antenna VSWR is highBackground noise level on AIS receiver is highOrange(No Transmit)Solid Device initializing, silent mode, waiting to transmitFlashing Acquiring a GPS fixRed (Error) Solid/Flashing Built in integrity test error(See troubleshooting section for more info)Congratulations on your purchase. Your XB-8000 / XB-6000 AIS Transponder is a Class B AIS Transponder with integrated NMEA 2000 and WiFi* connectivity.The XB provides information to improve your situational awareness and assist in avoiding collisions at sea. Because it consumes very low power it may be left turned on whenever your vessel is underway. It works by interpreting Universal Shipborne Automated Identification System (AIS) messages which are sent over VHF by transponders installed on other vessels. The AIS system uses two dedicated VHF channels designated for this purpose and with the installation of the XB to receive these signals, you can distribute this information to other devices on board your vessel (e.g. chart plotters, laptops, smart phones) using NMEA 2000, USB and WiFi*. In addition, your vessel data is transmitted to other AIS-equipped vessels within range. For more information on AIS go to www.vespermarine.com/xb.(*XB-8000 only)XB-8000 or XB-6000External GPS Antenna with 10m cable10 pin power/data cableAIS/VHF antennaMMSI numberPC/Mobile Device for configuring XB settings2A fuse or circuit breaker1m USB cable (for configuration)Waterproof 5m USB cable with locking security ringNMEA 2000 cable, T connector and network extension cableSP160 Antenna Splitter Consider other equipment you may need to install this on your vessel e.g. additional cable, cable ties, mounting screws, wire strippers, screw driver etc.• AIS/VHF antenna• NMEA 2000 • GPS antenna• 10 pin power/data port• LED Status185mm (7 1/4”)98mm (3 7/8”)• USBMount your XB at least 0.6m (2 feet) from any compass. Test your compass to verify that it operates properly when the XB is operating.
VHF ANTENNAGPS ANTENNA!POWER AND DATACOLOR DESCRIPTIONRed DC positive (+) (12-24 volts). Always use a 2A fuse or circuit breaker. Do not connect directly to battery. If you must extend the power connections use high quality pre-tinned marine grade wire which is at least 16 AWG (1.5mm2).Black DC negative (-)Gray NMEA data out (+) AYellow NMEA data out (-) BGreen NMEA data in (+) AWhite NMEA data in (-) BBrown External silent mode switch. Do not connect if not used.(Do not connect blue or pink wire)DATA OUT (+) AXB CHART PLOTTERDATA OUT (-) BDATA IN (+) ADATA IN (-) BHEADING SENSORDATA OUT (+) ADATA OUT (-) BDATA IN (+) ADATA IN (-) B(Gray)(Yellow)(Green)(White)38400 Baud4800 BaudDC NEGATIVE / GROUND(Brown)EXTERNAL SWITCH OUTPUTSILENT MODE SWITCHNMEA 0183 EXAMPLE• A dedicated VHF antenna or Vesper Marine AIS/VHF Antenna Splitter is required.• Make sure your VHF antenna is an omni-directional antenna designed for the marine band (156-162MHz) and is well tuned at the AIS end of the band (VSWR 2:1 or less at 162MHz).• Mount the antenna as high as possible (at least 2-3 metres (6-10 ft) above the water surface) and as far as practical from any existing VHF, HF or radar antennas and any metal structures. It is not recommended to place the VHF antenna directly alongside a mast or another VHF antenna such as on a mast-head.CAUTION: Never operate this device unless it is connected to a suitable VHF antenna or Vesper Marine AIS/VHF Antenna Splitter. Performance cannot be assured if you use any other antenna splitter. The use of an improper splitter may damage the device and void your warranty.HINT: Use the VSWR meter in the vmAIS or WatchMate App (see configuration section) to check your antenna system installation.• The XB requires a GPS fix before it can transmit its position.• The GPS antenna should be situated so that it has an unobstructed view of the sky above.• Do not place the GPS antenna near or in the path of radar or HF antennas.• The antenna cable is terminated with a small SMA connector to facilitate easy routing through holes and openings. Do not cut the cable unless you have the proper tools to crimp a new connector. Make the connection to your AIS transponder last after antenna installation is complete.CAUTION: The GPS antenna provided is designed specifically for use with the XB Transponder. Performance cannot be assured unless you use a Vesper Marine GPS antenna. Use of a different antenna may damage your XB and void your warranty.HINT: Use the GPS Status screen in the vmAIS or WatchMate App (see configuration section) to view satellite signal strengths which will assist in determining the best location for the antenna.!A 2m (6.5’) cable with attached 10 pin connector is supplied for connecting the XB to power, other devices over NMEA 0183 and an external silent mode switch. You may extend this cable as necessary.• Check you have the VHF antenna connected before connecting to power. • Fully engage the locking ring to ensure a watertight seal.• Received NMEA 0183 data is output on WIFI* and USB. Hint: Silent Mode can also be controlled over USB and WiFi*. External switch is an optional manual override.
NMEA 2000USB• When you connect to your PC over USB the XB will automatically enumerate itself as a COM port (see configuration section).• On the first connection, most operating systems will automatically install the necessary drivers. In some cases this may not be successful so the drivers are available for download from www.vespermarine.com/xb.WIFI (FOR XB-8000 ONLY)DROP CABLET CONNECTIONNETWORKPOWERNETWORKEXTENSION CABLETERMINATINGRESISTORCHART PLOTTERThe XB can be connected to a NMEA 2000 network to enable AIS and GPS data to be sent to other NMEA 2000 devices. The XB can also receive and make use of data sent from NMEA 2000 sensors.• Data Packets (PGN’s) supported are defined below.• A drop cable, T connection and network extension cable are required to connect the XB to your NMEA 2000 network.Supported PGN’sBe sure to check out www.vespermarine.com/xb for an up-to-date list and description of PGN’s that are supported.PGNs Received127250 Vessel HeadingPGNs Sent129025 Position129026 COG & SOG129038 AIS Class A Position129039 AIS Class B PositionPGNs Sent (continued)129040 AIS Class B Extended Position129794 AIS Class A Static Voyage 129798 AIS SAR Aircraft Position129801 AIS Addressed Safety 129802 AIS Safety Related Broadcast129809 AIS Class B “CS” Static, Part A129810 AIS Class B “CS” Static, Part BAccess Point Mode (default)The XB-8000 will control your onboard WiFi network of up to 5 devices. You can connect to the XB-8000 using:• Network (SSID): VesperXB• Password: WatchMateWe recommend that you change your password straight away and write it down here for future reference:____________________. You can recover your password over USB if you forget it.• The default IP address that mobile apps may need is 192.168.15.1 (Port 39150).Client ModeThe XB-8000 can also join an existing network. It can do this in either DHCP mode (default) or you can set a static IP address using vmAIS (see configuration section). To prevent the address from automatically changing we recommend that you use a static IP address.Wireless Access Point DAP - 1353iPadiPad
CONFIGURATION• Before the XB can transmit your position you must configure your vessel details and enter a valid MMSI number. Your MMSI may have been entered already by your dealer. You must have an assigned MMSI for your vessel. If you do not have an assigned MMSI, contact the relevant authority in your country.• You can configure your XB using the WatchMate App* or the vmAIS PC software. These are available for download from www.vespermarine.com/xb.• With vmAIS you can connect to the XB using either the USB virtual COM port or over WiFi* by entering the IP address (192.168.15.1 default). Click the connect button. Allow 30 seconds for the XB to initialize after power on before attempting to connect. Enter your vessel details using this screen: • Once you save the MMSI number you cannot change it. If you need to change the MMSI, please contact an authorized dealer or Vesper Marine. • When all the information is correct, click on the Save Vessel Data button.• You can also change your WiFi* settings, view your GPS signal strength, Transponder status and VSWR level using vmAIS. *(XB-8000 only)YOU’RE FINISHED!GOT A QUESTION?Visit www.vespermarine.com/xb for comprehensive answers to frequently asked questions, technical support, downloads, local dealer contacts and more…If the Status LED is solid green, the XB is transmitting your position and is successfully installed! Your position will be transmitted every 3 minutes when your speed is under 2 knots or every 30 seconds otherwise. Your vessel information (e.g. name, callsign, etc) is transmitted every 6 minutes. If the Status LED is not solid green yet, see the troubleshooting section for the probable cause.
TECH SPECSSize 200mm wide x 130mm high x 60mm depth (7 7/8” x 5 1/8” x 2 3/8”)Power supply 12-24 VDC 2A max, 3W nominalEnvironmental Watertight (USCG CFR-46, IPx7)Operating temperature -25°C to +55°C (-13°F to 131°F)Storage temperature -25°C to +80°C (-13°F to 176°F)Serial data 1 USB port (isolated), 1 NMEA input (isolated RS422), 1 NMEA output (non-isolated RS422)Data port impedance NMEA input: 96k ohm, NMEA output: 28 ohmNMEA 0183 output ALR, RMC, GSV, GSA, GGA, GLL, VTG, VDO, VDM, TXT, DSCNMEA 0183 input HDG, HDM, HDTNumber of receivers 2 AIS, 1 DSC (timeshared)Number of transmitters 1 AISReceive frequency range 156.025 – 162.025 MHzTransmit frequency range 161.500 – 162.025 MHzAIS sensitivity -113 dBm < 20% PERPower output 33 dBm (2W)GPS sensitivity -159dBm tracking & navigation-142dBm acquisitionGPS SBAS support WAAS, EGNOS, MSAS, GAGANPower/data connector 10 pin circularUSB connector Mini USB (USB 2.0)GPS antenna connector SMAVHF antenna connector SO-239VHF antenna required 50 ohm, max 2:1 VSWR @ 162MHz. PL-259 connectorNMEA 2000 connector NMEA 2000 Micro-CFirmware version 5.06Wireless 802.11 b/g in Access Point or Client ModeAccess point security WPA2 - PersonalClient mode security None, WPA & WPA2 PersonalSTATUS LED TROUBLESHOOTINGCOLOR STATE DESCRIPTIONOrange Solid Device initializingBefore the XB can transmit it needs 1 minute to initialize.MMSI not programmedYou must have a valid MMSI programmed before you can transmit your position (see configuration section). Silent modeSilent mode is on. If this is not intentional check the brown wire has not been accidentally connected to DC negative or vessel ground.Last position report not sentThis may happen from time to time in very busy areas with lots of AIS traffic. This is normal behavior for a Class B AIS device.Flashing Acquiring a GPS fixThe XB requires a GPS fix before it can transmit its position. This may take a few minutes. If it is taking a long time check your GPS antenna installation (see GPS antenna section) and GPS signal strength using vmAIS.Green Flashing Antenna VSWR is highCheck your antenna installation. Use the VSWR meter in the vmAIS status page. A poorly tuned antenna, bad cabling or connections are typical reasons for a high VSWR. Your XB will continue to operate normally but transmit performance will degrade.Background noise level on AIS receiver channel is highAn AIS receiver channel has an abnormally high background noise level. Determine the channel and frequency by using the vmAIS status page. Look for an RSSI level greater than -77dBm. Remove any sources of noise onboard at this frequency. Your XB will continue to operate normally but receive performance will degrade.Red Solid/FlashingBuilt in integrity test errorAn internal error has been detected. The XB may automatically recover, but if the error state persists contact our technical support network for assistance www.vespermarine.com/xb.
WARNINGS !!This AIS Transponder works in conjunction with other vessels and systems such as other AIS transponders and GPS devices. The accuracy of this device and the AIS system can be affected by many factors, including equipment failure or defects, environmental conditions and incorrect installation, handling or use. Vesper Marine does not warrant that this product is error-free. It is the user’s responsibility to exercise common prudence and navigational judgement. This device should not be relied upon as a substitute for such prudence and judgement. Always maintain a permanent watch so that you can respond to situations as they develop. The prudent mariner will not rely on a single aid to navigation. The user should verify the information obtained from this AIS Transponder is in accordance with expected situations and conditions. The information is not guaranteed to be accurate or reliable and this AIS Transponder is not a substitute for proper seamanship.Vesper Marine Limited cannot be held liable for any injury, damage or loss, caused by, during, or because of the installation, use or inability to use this device. This AIS Transponder is to be installed and used entirely at your own risk. By installing and/or using this AIS Transponder you fully accept this risk and agree to hold Vesper Marine Limited harmless. Intended UseThis product is intended to be used on leisure or commercial vessels (excluding IMO/SOLAS class). Vesper Marine has designed and manufactured this product to be used only aboard vessels.Warranty VoidDo not disassemble the unit or remove the screws which hold it together. The unit is sealed and disassembly will void the warranty.FCC Warning:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.Industry Canada Warning:This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.To satisfy RF exposure requirements for mobile transmitting devices, a separation distance of 1 metre or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.This device has been designed to operate with an antenna having a maximum gain of 3dBi. Antennas having a gain greater than 3dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.To reduce potential radio interference to other users, the antenna type and its gain should be chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication.Pour satisfaire aux exigences d’exposition aux frequencies radio pour les appareils mobiles de transmission, une distance de 1 mètre ou plus doit être maintenue entre l’antenne de ce dispositif et les personnes pendant son fonctionnement. Pour assurer la sécurité, les opérations plus près de cette distance ne sont pas recommandées.L’antenne utilisée pour ce transmetteur ne doit pas être co-localisés avec toute autre antenne ou transmetteur.Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximalde 3dBi. Les antennes ayant un gain supérieur à 3dBi sont strictement interdits pour une utilisation avec cet appareil. L’impédance d’antenne requise est de 50 ohms.Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisis pour que la puissance isotrope rayonnée équivalente (PIRE) ne soit pas supérieure à celle requise pour une communication réussie.MMSI Programming WarningIMPORTANT: In most countries the operation of an AIS unit is included under the vessel’s marine VHF license provisions and the vessel on which this device is to be installed may be required to possess a current VHF radiotelephone license which lists the AIS system and the vessel Call Sign and MMSI number.An MMSI number is required in order for this device to operate as a transmitter.Please contact the relevant authority in your country for more information.For Customers in the USAThis device must be programmed with data corresponding to the vessel on which it will be installed. Programming must be carried out by a Vesper Marine dealer. The included instructions contain information on how to verify the correct programming.WARNING: It is a violation of the rules of the Federal Communications Commission to input an MMSI that has not been properly assigned to the end user, or to otherwise input any inaccurate data in this device.RF Emissions WarningsCAUTION: This device generates and radiates electromagnetic energy. This device must be installed and operated according to the instructions contained in this manual. Failure to do so may result in product malfunction and / or exposure to potentially harmful levels of radio frequency radiation. Changes or modifications to the unit not expressly approved by Vesper Marine Ltd will void the user’s authority to operate this equipment.CAUTION: The system has a Maximum Permissible Exposure (MPE) radius of 1m from the antenna. This has been determined assuming the maximum power of the transmitter and using a standard half-wave monopole VHF antenna with a maximum gain of 3dBi and termination impedance of 50 ohms.When installing the antenna and operating the equipment consider the following:• The antenna should be mounted as high above deck as possible.• Higher gain VHF antennas will require a larger MPE radius.• Do not operate the unit when anyone is within the MPE radius of the antenna.• The antenna should not be collocated or operated in conjunction with any other transmitting antenna.
WARRANTYThis transponder is warranted, when properly installed and used, to be free from defects in materials or workmanship for two years from the date the product was purchased by the first retail customer. This warranty applies to the original retail purchaser only and is not transferable. Within this period, Vesper Marine will, at its discretion, repair or replace any components which fail in normal use. Repairs or replacement will be made at no charge for parts or labor, provided that the customer shall be responsible for any transportation costs. This warranty does not cover failures due to abuse, misuse, accident, improper installation, unauthorized alterations or repairs, shipping damage, wear and tear, or corrosion.This warranty will not apply if the product’s external housing has been opened, the serial number or other labels have been removed or altered or the specified input voltage has been exceeded. This warranty is void if the product has been operated with an incompatible GPS antenna or without a suitable VHF antenna.This warranty is in addition to all other rights available to the consumer under any applicable statute and your statutory rights are not affected by this warranty.Vesper Marine retains the exclusive right to repair or replace the unit or offer a full refund of the purchase price at its sole discretion. In addition, Vesper Marine retains the exclusive right to replace the unit with a factory reconditioned unit or a new unit at its sole discretion. Where a replacement is provided the original product becomes the property of Vesper Marine and the warranty will remain from the original purchase date.This warranty applies only to products supplied new to you by an authorized dealer or Vesper Marine and you have not bought the product for resale.In no event shall Vesper Marine be liable for any incidental, special, indirect, or consequential damages, whether resulting from the use, misuse or inability to use the product or from defects in the product.Vesper Marine declares that this product is in compliance with the essential requirements and other provisions of the R&TTE directive 1995/5/EC.This product is for use worldwide, including the following European countries:This device is also approved for use in the United States, Canada, Australia and New Zealand.Electronic Waste RecyclingVarious regional and national regulations exist regarding the recycling of certain electronics.Please consult your local authorities or contact Vesper Marine for recycling information. AT BE BG CH CY CZ DE DKEE ES FI FR GR HU IE ISIT LT LU LV MT NO NL PLPT RO SE SI SK UK NOTES
Copyright © 2012, Vesper Marine Ltd. AIS WatchMate, WatchMate Vision and WatchMate Wheel are trademarks of Vesper Marine Ltd. All other products are trademarks or registered trademarks of their respective owners. Unless otherwise indicated, all documentation and operating software contained within this product or distributed with this product is copyrighted by Vesper Marine Ltd. All rights are reserved.Portions of this product may use software licensed under open source license agreements. Source code for the applicable software is available upon request from Vesper Marine Ltd.Phone +64 9 950 4848 | Email info@vespermarine.comFax +64 9 950 4085 | Web www.vespermarine.comFollow us on Facebook | www.facebook.com/vespermarineMember of:

Navigation menu