ViRZTEX 60002 26.96-27.28 MHz Wireless R/C Toy-TX User Manual Dyna Blade II Instruction Sheet 03

ViRZTEX Company Limited 26.96-27.28 MHz Wireless R/C Toy-TX Dyna Blade II Instruction Sheet 03

Users Manual

Download: ViRZTEX 60002 26.96-27.28 MHz Wireless R/C Toy-TX User Manual Dyna Blade II Instruction Sheet 03
Mirror Download [FCC.gov]ViRZTEX 60002 26.96-27.28 MHz Wireless R/C Toy-TX User Manual Dyna Blade II Instruction Sheet 03
Document ID987760
Application IDUCKqrVGW5PZRe1KfmmDrTg==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize197.59kB (2469814 bits)
Date Submitted2008-08-20 00:00:00
Date Available2008-08-20 00:00:00
Creation Date2008-07-23 16:43:20
Producing SoftwareAdobe PDF library 7.77
Document Lastmod2008-07-23 16:43:20
Document TitleDyna Blade II Instruction Sheet 03
Document CreatorAdobe Illustrator CS2

Aero Graviteer™ 3-Channels Digital Proportional R/C Helicopter
Easy to Fly! Anyone can master it like a PRO!
BATTERY SAFETY INFORMATION:
Instruction Manual
Batteries should always be replaced by an adult.
Do not mix old and new batteries.
Do not mix alkaline, standard(Carbon-Zinc), or rechargeable(Nickel-Cadmium or Nickel Metal Hydride) batteries.
Non-rechargeable batteries are not to be recharged.
Rechargeable batteries are to be removed from the toy before being charged(if removable).
Rechargeable batteries are only to be charged under adult supervision(if removable).
Different types of batteries or new and used batteries are not to be mixed.
Only batteries of the same or equivalent type as recommended are to be used.
Batteries are to be inserted with the correct polarity.
Exhausted batteries are to be removed from the toy.
The supply terminals are not to be short-circuited.
Do not dispose of battery in fire. Battery may explode or leak as a result.
Remove batteries from the toy before prolonged storage.
Disposed of used batteries properly.
Please retain this information for future reference.
8+
NOTE:
(1) Charging takes around 30-45 minutes.
(2) Shorter charging time may occur if your Aero Graviteer™ is
only partially drained.
(3) Turn off your Aero Graviteer™ and disconnect it from the
radio controller/ charger when charging is completed or before
storage.
(4) Average flight time is around 3-4 minutes off one full
charge.
(5) Charge time and flight time may vary depending on radio
controller battery level.
CONTENTS LIST AND PARTS IDENTIFICATION:
Aero Graviteer™
Power Switch
OFF
ON
Fly Bar
Upper Rotor Blade
LED
Indication
of DGP:
Charge Socket
Lower Rotor Blade
(Helicopter)
Tail Fin
CAUTION: (SAFE USE OF LITHIUM POLYMER RECHARGEABLE BATTERY)
Charge Aero Graviteer™ ONLY with the provided Radio Controller/ Charger. NEVER attempt to charge with any other charger.
The newly purchased Aero Graviteer™ is only partially charged. Full charge your Aero Graviteer™ before first use.
Do not recharge Aero Graviteer™ immediately after use. Wait for 10 minutes before recharging.
Do not charge near fire, or where temperature is extremely high, or where it is wet or damp.
During charging, keep your Aero Graviteer™ away from combustible materials including paper, plastic, carpets, vinyl, leather, wood and never charge inside a
full-sized automobile!
Never attempt to disassemble or modify Aero Graviteer™ as it may damage the Lithium Polymer rechargeable battery inside.
Always store Aero Graviteer™ in cool and dry place. Keep away from direct sunlight.
Do not allow Aero Graviteer™ to get wet.
Always switch off the Aero Graviteer™ after use or before storage!
Never leave your Aero Graviteer™ and Radio Controller/ Charger unattended at any time during charging.
Always full charge your Aero Graviteer™ before prolonged storage. Examination and recharging should be carried out periodically.
If your Aero Graviteer™ shows severe damages or deformation under improper use and handling, stop using immediately and disposed of properly.
FCC/EMC REQUIREMENTS:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Dynamic Gravity
Pro System (DGP)
LED Window
VALID FOR CANADA ONLY – This Category II radiocommunication device complies with Industry Canada Standard RSS-310.
Ce dispositif de radiocommunication de catégorie II respecte la norme CNR-310 d’Industrie Canada.
Radio Controller/ Charger battery level low. Replace the
6 x 1.5v AA(LR6) batteries with brand new ones.
Blue Flash
CHARGE MODE: Helicopter disconnected/ not connected.
Red
CHARGE MODE: Charging in progress.
Red Flash
2008 Dekko Toys Company Ltd.
Dekko Toys is a registered trademark of Dekko Toys Co., Ltd. in Hong Kong and/or other countries.
Li-ion
AERO GRAVITEER™ is a trademark of Dekko Toys Co., Ltd.
Product and colors may vary.
All rights reserved.
Carefully read the provided instruction manual as it contains important information.
Dekko Toys Company Ltd., 1204-05, Tower A, New Mandarin Plaza, 14 Science Museum Road,
Conform to product safety standard ASTM F963-07 and EN71 regulatory requirements.
Tsimshatsui East, Kowloon, Hong Kong
Please retain this information for future reference.
Tel: (852) 3620 2290 Fax: (852) 3107 0313
Item#60002(27.145MHz)
Dekko Toys Europe bvba, Remise 3, 3930 Hamont, Belgium
www.dekkotoys.com
P/N #60002-IS-EN-01-R0
MADE IN CHINA
Tel: (32) 11 80 62 10 Fax: (32) 11 40 18 20
Turn right
CHARGE MODE: Charging completed.
Red
Turn left
Green
Helicopter is turned off.
Helicopter goes into sleep mode after being
idle for 15 minutes.
Helicopter faulty. Charging is stopped.
Red Rapid Flash
Off
Off
SLEEP MODE: When the Remote Controller/ Charger is
idle for 15 minutes, or when charging is completed for 15
minutes, it will automatically shut-off to preserve battery.
Landing Gear
Power Indicator
Charging Indicator
Charge Plug
Check to make sure contents are complete:
1) Aero Graviteer™ 3-Channels R/C Helicopter x 1
2) Radio Controller/ Charger x 1
3) Instruction Manual x 1
4) Spare Upper Rotor Blade x 2
5) Spare Lower Rotor Blade x 2
6) Spare Fly Bar x 2
Slide the “Charging/ On/
Off” switch of the Radio
Controller/ Charger
to “ ” position
Trimmer
for Forward/ Backward
Charging/
On/ Off/ Switch
Power Switch
OFF ON
Blue LED
lights up
Trimmer
for Yaw Control
TRIM CORRECTION:
1 Hovering
2A Out of Trim: Spinning clockwise
GETTING STARTED:
1 Unscrew the battery door
2B Out of Trim: Spinning counter-clockwise
Tap
2 Battery Installation - Radio Controller/ Charger
Install 6 x 1.5V AA(LR6)
batteries (not included) in
battery compartment.
Make sure to follow the
correct positive (+) and
negative (-) polarities
with the corresponding
markings inside the
battery compartment.
Power Switch
OFF ON
Charge Socket
Turn right and
go backward
REPLACE ROTOR BLADE
REPLACE FLY BAR
CAUTION! Before replacing the rotor-blades,
make sure both the controller and helicopter
are switched “OFF”.
-Use a screwdriver to unscrew the rotor-blade.
-Replace the rotor-blade.
-Tighten up the screw.
CAUTION! Before replacing the fly-bars, make
sure both the controller and helicopter are
switched “OFF”.
-Use a screwdriver to unscrew the fly-bar.
-Replace the fly-bar.
-Tighten up the screw.
Loosen
Tighten
Loosen
Tighten
NOTE: BUILT-IN ELECTRONIC PROTECTION
Aero Graviteer™ is designed and built in with electronic protection. The helicopter will automatically shut off if the rotors are stalled or battery
level gets too low. If you find the helicopter shut off itself during play, check carefully whether there is any bad deformation to the helicopter
before reset. To reset, simply slide the helicopter’s ON/OFF switch to OFF and then ON again. If the battery level gets too low that the helicopter
cannot lift off, recharge it immediately.
3 Reinstall battery door and tighten the screws.
4 Pull out the charge plug from the back of
Radio Controller/ Charger.
3 feet
(1m)
2C Out of Trim: Drift forward
2D Out of Trim: Drift backward
FLYING TIPS:
Tap
” position
“ ” LED will flash red when
charging. Once completed, it
will turn green.
Go backward straight
REPLACE ROTOR BLADE AND FLY BAR :
Tap
6 Slide the “Charging/ On/ Off” switch of the Radio Controller/ Charger
to “
Turn left and
go backward
and push up slowly and gently. The upper and
lower rotors will spin and build up to speed
gradually. Your Aero Graviteer™ will take off
now!
During startup, the DGP
LED red light will move
backward and return to
reach to its neutral position.
Now your Aero Graviteer™ is
ready to take off !
Directional
Control Stick
Throttle Control
Stick
3 Press your left thumb onto the throttle stick
Turn on your Aero Graviteer™
Note: For best performance, alkaline batteries
are recommended.
If at any time in the future you should need to
dispose of this product please note that waste
electrical products should not be disposed of
with household waste. Please recycle where
facilities exist. Check with your local authority
or retailer for recycling advice.(Waste
Electrical and Electronic Equipment Directive)
Turn right and
go forward
Normal Operation in Flight Mode.
READY: Successful communication with radio
controller.
Go forward straight
Turn left and
go forward
Blue
STANDBY MODE: Waitiing for radio controller
to turn on.
LED Indication of Radio
Controller/ Charger:
PREPARING TAKE-OFF:
Charge Plug
®
Red/ Green
Antenna
5 Insert the charge plug into helicopter as shown
Hereby, Dekko Toys Company Ltd., declares that this AERO GRAVITEER™
Helicopter is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Blue
Off
RSS-310 OF INDUSTRY CANADA:
Contains LiPo battery pack.
Battery pack must be recycled
or disposed of properly
Red Flash
Radio Controller/ Charger
Aero Graviteer™ is powered by a light-weight Lithium Polymer rechargeable battery and extra care must be taken during use. Failure to follow
these care and handling instructions can quickly result in severe, permanent damage to the Lithium Polymer rechargeable battery and its
surroundings.
DIRECTIONAL FLIGHT CONTROL (AFTER TRIM CORRECTION):
Tap
(1) Hovering
- Hover your Aero Graviteer™ about 3 feet(1m) above ground (keep it at constant altitude). You may need to continuously adjust throttle
gently up or down to achieve hovering.
(2) Trimming - If your Aero Graviteer™ shows one of the followings:
A.
B.
C.
D.
E.
Spin clockwise - gently tap the LEFT trimmer button until the hovering helicopter stops spinning.
Spin counter - clockwise - gently tap the RIGHT trimmer until the hovering helicopter stops spinning.
Drift forward - gently tap the BACKWARD trimmer button until the hovering helicopter stays stationary.
Drift backward - gently tap the FORWARD trimmer button until the hovering helicopter stays stationary.
Stay straight – no trimming is required.
(3) When trimming is done, your Aero Graviteer™ is ready to traverse at your command.
- Always press and push gently the throttle and direction sticks during flight control. The digital proportional controls respond precisely to small movement of
control stick.
- Beware of turbulence and strong winds in the flying area. Your Aero Graviteer™ may wobble, or be blown off its track, or even dive back to ground as a result.
- Never fly your Aero Graviteer™ over 10 feet(3m) above ground or get too close to the ceiling and wall.
- If your Aero Graviteer™ is about to hit onto an obstacle, crash, or losing control, release the throttle stick immediately and let the helicopter fall freely and safely
back to ground.
- Always full charge your Aero Graviteer™ before use.
- In cold or high altitude environments, your Aero Graviteer™ may not perform as good.
IMPORTANT SAFETY INFORMATION:
Keep Aero Graviteer™ clear from face and eyes at all times.
Keep fingers away from spinning rotors and fly bar.
Always fly in wide open space without any obstacles.
Do not fly towards people or animals.
Do not fly under adverse weather condition.
Always fly in warm and sunny days, with little or no wind.
Do not fly in temperatures below 45°F/7°C.
Adult supervision recommended at all times.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1.1-111
Format                          : application/pdf
Title                           : Dyna Blade II Instruction Sheet 03
Creator Tool                    : Adobe Illustrator CS2
Create Date                     : 2008:07:23 16:43:20+09:00
Modify Date                     : 2008:07:23 16:43:20+08:00
Metadata Date                   : 2008:07:23 16:43:20+08:00
Thumbnail Width                 : 256
Thumbnail Height                : 88
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 12020 bytes, use -b option to extract)
Document ID                     : uuid:980DC8559358DD11AA32B084ACE4D26B
Instance ID                     : uuid:d0d363c7-9ab5-441a-a231-12d17f6f7b3a
Derived From Instance ID        : uuid:970DC8559358DD11AA32B084ACE4D26B
Derived From Document ID        : uuid:6544CF02E84EDD11B1A5FFA240CFFFF1
Producer                        : Adobe PDF library 7.77
Page Count                      : 1
Creator                         : Adobe Illustrator CS2
EXIF Metadata provided by EXIF.tools
FCC ID Filing: T8860002

Navigation menu