Vinotemp Wine Mate Vino2500Ssd Users Manual Wm2500 8500ssd Installation

WM250-850SCU to the manual 5ae72b2f-1008-4079-af1f-f4961621a31a

: Vinotemp Vinotemp-Wine-Mate-Vino2500Ssd-Users-Manual-456823 vinotemp-wine-mate-vino2500ssd-users-manual-456823 vinotemp pdf

Open the PDF directly: View PDF .
Page Count: 8

VINO2500SSD, 4500SSD

VINO6500SSD, 8500SSD

Installer’s Instruction

Federal law requires that WINE-MATE split cooling systems be

installed by an EPA certified refrigeration technician.

WINE-MATE split system is shipped as components and is ready for use only

after a certified refrigeration technician has properly installed, chatged and tested

the system. Proper installation is critical. Vinotemp can only warrant the quality of

the components. The installation and proper operation of the system must be

warranted by the installer. Installation of the system must be done in accordance

with all state and local building codes.

The condensing unit and evaporator unit are connected by a liquid line and an

insulated suction line that are supplied by the installer. These lines must be

properly sized for the distance between the two units. After the units and the lines

are installed, the system must be pressure tested. If no leaks are found,

evacuate and charge system with R134A. Refrigerant amount will vary

depending on the length of line set.

1. Condensing Unit

• Place the condensing units WM250-850SCU in a properly ventilated

location. If it is not, heat exhausted by the condensing unit will build up

and the cooling system will not operate properly.

• Leave minimum 5 feet clearance for the exhaust side and leave minimum

1 foot clearance for the fresh air intake side.

• Condensing unit shall be elevated to avoid possible flooding and shaded

from direct sun. It shall not be exposed to temperatures higher than 110

°F or lower than 45 °F (optional low ambient kit for 20 °F).

2. Evaporator Unit

- 1 -

• The WM25-85SFCD evaporator units shall be installed for ceiling mount

with air supply on both sides and air return on the bottom.

• Supply and return air flow from the evaporator unit shall be unobstructed

for at least 1 foot.

• There is a gravity drain line so that it can not be installed above the

evaporator unit. Otherwise a condensation pump must be used.

3. Air Sensor

• The air sensor can be located in the wine room or the return air area, but

not the supply air area.

4. Refrigeration Piping and Charging

NOTES: ALWAYS USE THE SUPERHEAT AND SUBCOOLING,

PRESSURE READINGS TO CHARGE REFRIGERANT PROPERLY, THE

LISTED CHARGES ARE FOR REFERENCE ONLY.

• The installation order starts from condensing unit (including the receiver),

liquid line filter-drier, moisture-liquid indicator (sight glass), liquid line,

evaporator unit (including liquid line solenoid valve and thermostatic

expansion valve or automatic expansion valve), suction line, and returning

to condensing unit.

• The subcooling at the condensing unit shall be around 10°F. The charge

may be complete when there are no more bubbles forming in the sight

glass.

• If equipped with a TXV, the evaporator superheat is set around 8-10 °F for

a 10 °F TD system at factory.

• If equipped with an AXV, the valve is set around 38-40°F at factory and

the superheat at the evaporator unit shall be around 9-18°F under low and

high load at 75°F ambient temperature.

• Low side pressure: 33 psig

• High side pressure: 130 psig at 75 °F ambient temperature and 150 psig

at 90 °F ambient temperature

The line sizes and refrigerant charges are listed as follows.

MODEL REFRIGERATION

LINES LIQUID

LINE SUCTION

LINE DRAIN

LINE CHARGE

VINO-

2500SSD < 50 FT 1/4"

OD 3/8” OD 1/2” OD R134a/

20 OZ

VINO-

4500SSD < 50 FT 1/4"

OD 1/2” OD 1/2” OD R134a/

26 OZ

VINO-

6500SSD < 50 FT 1/4"

OD 5/8” OD 1/2” OD R134a/

32 OZ

VINO-

8500SSD < 50 FT 3/8"

OD 5/8” OD 1/2” OD R134a/

38 OZ

- 2 -

5. Pressure, Superheat and Subcooling Readings

NOTES: THE VALVES MUST BE IN THE MIDDLE POSITIONS TO READ

PROPERLY.

Complaint Possible Causes

a. High suction pressure and low head pressure

b. High suction pressure and low head pressure

Low superheat and low subcooling

c. High suction pressure and high head pressure

Low superheat and high subcooling

d. High to normal suction pressure and high head pressure

Low subcooling

e. High suction pressure and high head pressure

Low subcooling

f. High suction pressure and high head pressure

High superheat

g. Low suction pressure and low head pressure

High superheat and low subcooling

h. Low suction pressure and low to normal head pressure

High superheat and high subcooling

i. Low suction pressure and low head pressure

Low subcooling

j. Low suction pressure and low head pressure

Low superheat and low subcooling

k. Low suction pressure and low to normal head pressure

High superheat and normal to high subcooling

l. Low suction pressure and normal head pressure

High superheat and normal subcooling

m. Low suction pressure and high head pressure

High superheat and high subcooling

n. Low suction pressure and high head pressure

High superheat and high subcooling

o. low to normal suction pressure and high head pressure

High to normal superheat and high subcooling

a. Compressor may be bad

b. Expansion valve opened, too

much oil

c. Overcharge

d. Non-condensable gas

e. Air restricted, dirty condenser,

bad condenser fans

f. High room temperature, high

evaporator load

g. Undercharge

h. Liquid line restricted after

receiver, solenoid valve

restricted

i. Suction line restricted

j. Air restricted at evaporator,

evaporator iced

k. Evaporator restricted

l. Expansion valve restricted

m. Both evaporator and condenser

restricted

n. Liquid line restricted before

receiver

o. Condenser restricted

6. Valve Operation

SPINDLE BACK POSITION SPINDLE FRONT POSITION SPINDLE MIDDLE POSITION

Fig. 2.1 Valve Operation

- 3 -

Back Position: Process and manometer port closed for normal operation

Front Position: Main connection to liquid or suction line closed

Middle Position: All ports open for vacuum, charge and measurement

7. Electrical Wiring

Fig. 2.2 VINO2500 & 4500SSD Electrical Wiring Diagram (VTSTAT)

Fig. 2.3 VINO2500 & 4500SSD Wiring Diagram (DIGITAL CONTROLLER)

- 4 -

Fig. 2.4 VINO6500SSD Electrical Wiring Diagram (VTSTAT)

Fig. 2.5 VINO6500SSD Electrical Wiring Diagram (DIGITAL CONTROLLER)

- 5 -

Fig. 2.6 VINO8500SSD Electrical Wiring Diagram (VTSTAT, UJ6220Z)

Fig. 2.7 VINO8500SSD Wiring Diagram (DIGITAL CONTROLLER, UJ6220Z)

- 6 -

8. Use of the adjustable low pressure control (if applicable)

Cut out = 5 psig; Cut in = 25 psig; Differential = 20 psig

It may need to adjust the setting in the field to get the right cycle time.

8.1 P70AB-12

Fig. 2.8 P70AB-12 Adjustable Low Pressure Control

8.2 PS2-A7A

Fig. 2.9 PS2-A7A Adjustable Dual Pressure Control

- 7 -

Fig. 3.0 PS2-A7A Wiring Diagram

9. Condensing Unit Troubleshooting

Unit not running

a. Incorrect power supply

b. Incorrect or loose wirings

c. Failed components

d. Liquid refrigerant in the compressor

e. Low pressure switch shutting down the unit

a. Check for proper voltage

b. Check all wirings and connections

c. Check start relay, start capacitor, overload

protector, compressor.

d. Call service for OEM information

e. Check for system restriction or low

refrigerant