Viper Design VDW24D WiFi Module User Manual
Viper Design, LLC WiFi Module
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3781969 |
| Application ID | 0rQvodvixOOGPVjgqedSDQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 84.73kB (1059098 bits) |
| Date Submitted | 2018-03-15 00:00:00 |
| Date Available | 2018-03-15 00:00:00 |
| Creation Date | 2018-03-03 13:24:01 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2018-03-09 17:43:21 |
| Document Title | User Manual |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | User |
VDWIFIJID VDWIFIJID Users Guide Features 2.4Ghz - 2.5Ghz Wireless Link: UART/SPI interfaces Support for both mains-powered and battery-powered devices Operating Voltage: 3.0V to 3.6V typical Temperature Range: -40C to +85C Applications Battery Chargers Power Supplies iOT devices Integrated Networking Stack Integrated power management Integrated wireless Link Manufacture:Viper Design, LLC Note Warning: Changes or modifications to this device not expressly approved by Viper Design LLC could void the user’s authority to operate the equipment. Class B Device “NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.” RF Exposure This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with Maximum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d'exposition aux radiations dans un environnement non contrôlé. Cet équipement doit être installé et utilisé à distance minimum de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être co-localisées ou opérant en conjonction avec tout autre antenne ou transmetteur.” Viper Design LLC 125 Glancy St Goodlettsville, TN 37072 Phone: 615-325-0966 Version 0.2 Page 2 of 4 Low Power License-Exempt Device This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Labels Host Device must contain the following label on the outside of the unit: Contains FCC ID: 2AB7YVDW24D Contains IC: 20699-VPW24D Viper Design LLC 125 Glancy St Goodlettsville, TN 37072 Phone: 615-325-0966 Version 0.2 Page 3 of 4 SPECIFICATIONS Operational Supply Voltage: Operating Temperature: 3.0V to 3.6 -40C to +85C Radio 2.4GHz: Communication Interface: UART (2 wire: TX, RX) Line interface options: Logic level, RS-232, or RS-485 Data Format: 8 data bits, 1 stop bit, configurable parity bits Baud Rate: Configurable up to 115.2k SPI (4 wire logic level: SS, SCLK, MISO, MOSI) Data Format: 8 data bits Data Rate: Viper Design LLC 125 Glancy St Goodlettsville, TN 37072 Phone: 615-325-0966 Version 0.2 Page 4 of 4 F FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device. FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of20 cm between the radiator and user body. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2AB7YVDW24D Or Contains FCC ID: 2AB7YVDW24D” When the module is installed inside another device, the user manual of the host must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any company of the host device which install this modular with Single modular approval should perform the test of radiated emissionand spurious emission according to FCC part 15C : 15.247 requirement,Only if the test result comply with FCC part 15C : 15.247 requirement，then the host can be sold legally. IC statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes : ( 1 ) Ce dispositif ne peut causer d'interférences ; etc ( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. A separation distance of at least 20 cm is maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. Une distance de séparation d'au moins 20 cm est maintenue entre l'émetteur rayonnant structure (s) et le corps de l'utilisateur ou des personnes à proximité. For a host manufacture's using a certified modular, if (1) the module's IC number is not visible when installed in the host, or (2) if the host is marketed so that end users do not have straightforward commonly used methods for access to remove the module so that the IC number of the module is visible; then an additional permanent label referring to the enclosed module: "Contains Transmitter Module IC: " 20699-VPW24D " or "Contains IC: 20699-VPW24D" must be used.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : User Create Date : 2018:03:03 13:24:01-06:00 Modify Date : 2018:03:09 17:43:21+08:00 Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Creator : User Creator Tool : Microsoft® Office Word 2007 Metadata Date : 2018:03:09 17:43:21+08:00 Producer : Microsoft® Office Word 2007 Document ID : uuid:7ac074f6-b4db-45fd-9404-36b2fb4266bd Instance ID : uuid:8a273fd1-db73-4fd9-9824-29ceca6f558d Page Count : 6EXIF Metadata provided by EXIF.tools