Vision Fitness R2200 Users Manual WEB_R22HRT Assy4

R2200 to the manual 2711542a-bf7e-4aec-a5e6-20ef7a9fd298

: Vision-Fitness Vision-Fitness-R2200-Users-Manual-456984 vision-fitness-r2200-users-manual-456984 vision-fitness pdf

Open the PDF directly: View PDF .
Page Count: 8

Assembly

Guide

R2200 AND R2200HRT

SEMI-RECUMBENT FITNESS CYCLE

1

STEP

2

STEP

3

STEP

4

STEP

To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding, find

your new Fitness Cycle’s serial number located on the front axle tube, and enter here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be

sure to read your Owner’s Guide before using your new Fitness Cycle.

If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Cycle to prevent loos-

ening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely

tightening any ONE screw.

Assembly

Guide

R2200 AND R2200HRT

SEMI-RECUMBENT FITNESS CYCLE

TOOLS & PARTS INCLUDED

5mm Allen Wrench 15mm Pedal Wrench

Screwdriver

5mm L-Shaped Wrench

4mm L-Shaped Wrench

6mm L-Shaped Wrench

PARTS BOX

Console Mast Cover, Qty: 1

Pedals, Qty: 2

Power Supply, Qty: 1

Water Bottle & Cage, Qty: 1

Heart Rate Chest Strap (

R2200HRT Only

)

Color-coded Hardware Bags

Owner’s Guide

Assembly Guide

Warranty Card

ORANGE BAG BLUE BAG

PINK BAG

HARDWARE INCLUDED

M8 x 20L Screws

Quantity: 2

M8 x 65L Screw

Quantity: 2

M8 Lockwashers

Quantity: 4 M8 x 20L

Socket-head Cap Screw

Quantity: 4

M8 x 15L Screws

Quantity: 4

M8 Lockwashers

Quantity: 4

M6 Lockwashers

Quantity: 8

M6 x 55L Screws

Quantity: 8

M8 x 15L Screws

Quantity: 5

M8 x 20L Screws

Quantity: 2

M8 Lockwashers

Quantity: 6

5

1

STEP

1

STEP

• Slide the rear foot into place on the

frame. Secure the foot in place with

two screws (M8x20) and two lock

washers (M8) to the outside holes and

with two screws (M8x65) and two

lock washers (M8) to the inside holes.

Tighten with the blue-handled 5mm

allen wrench.

• Slide the rubber sleeve, located on

the rear support tube, into place over

the rear foot.

ORANGE BAG

Rear Foot

6

Seat Frame

B

A

Seat Bracket

R2200HRT

Seat Lever

R2200

2

STEP

2

STEP

• Place the seat bracket on the seat

frame. Secure in place with four

(M8x20) socket-head cap screws.

Tighten with the 6mm L-shaped wrench.

• Remove the socket-head cap screw in

front of the seat lever, located on the

right side of the seat frame, with the

4mm L-shaped wrench. Line-up the seat

lever into position on the bracket.

Reinsert the socket-head cap screw and

tighten with the 4mm L-shaped wrench.

• Take the seat frame handlebar and

connect the heart rate wires (A) exiting

its center to the heart rate wires (B) com-

ing from the seat frame.

• Mount the seat handlebars to the seat

frame with four screws (M8x15L) and

four lock washers (M8). Tighten with the

5mm allen wrench.

• Mount the seat backrest cushion to

the seat frame with four screws

(M6x55L) and four lock washers (M6).

Tighten with the 4mm L-shaped wrench.

• Mount the seat bottom cushion to the

seat frame with four screws (M6x55L)

and four lock washers (M6). Tighten

with the 4mm L-shaped wrench.

R2200HRT ONLY: Snap the plastic

cover onto the rear of the seat back.

BLUE BAG

7

3

STEP

3

STEP

• Slide the console mast cover onto

the console mast.

• Use the wire tie coming from the bot-

tom of the console mast to wrap around

the wire harness and heart rate wires

that are sitting in the frame bracket.

• Pull the wire tie up through the con-

sole mast so the wire harness and heart

rate wires exit the top of the mast.

• Slide the bottom of the console mast

into the frame bracket. Use the 5mm

allen wrench to secure the four screws

(M8x15) and four lock washers (M8)

to the sides of the console mast brack-

et. Use the 5mm L-shaped wrench to

secure the last screw (M8x15) to the

edge of the bracket facing the seat.

Tighten only until snug.

• Mount the console mast handlebar

to the console mast with two screws

(M8X20) and two lock washers (M8).

Tighten with the 5mm allen wrench.

• With a screwdriver remove the four

mounting screws from the backside of

the console. Connect the heart rate

wires and the wire harness to the pin

connectors on the backside of the con-

sole. Mount the console to the console

mast using the four mounting screws

and the screwdriver.

• Slide the console mast cover into place

so it integrates with the side covers.

• Mount the water bottle cage to the

console mast with the screws located

on the console mast.

PINK BAG

Console Mast

Handlebar

Console

Console Mast

Console Mast

Cover

R2200

8

500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551

toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373

www.visionfitness.com

©2005 Vision Fitness. All Rights Reserved. 1.05 Part #Z22RB42D-AG

AG18.16PRD

REV4

4

STEP

4

STEP

• Attach left pedal strap to left pedal

and right pedal strap to right pedal.

• Attach right pedal to right crank arm

and left pedal to left crank arm.

Tighten with the 15mm pedal wrench.

PEDALS