Visonic MCS700 Wireless Siren User Manual DE5420 2 W2002

Download:
Mirror Download [FCC.gov]
Document ID	422177
Application ID	BZGnJOhT0fSaZutQ157gGQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.57kB (232118 bits)
Date Submitted	2004-05-12 00:00:00
Date Available	2004-05-12 00:00:00
Creation Date	2004-05-12 13:18:00
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2004-05-12 13:18:00
Document Title	Microsoft Word - DE5420-2_W2002_.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	jacob_s

MCS-700
Wireless Siren
Installation Instructions
1. INTRODUCTION
The MCS-700 is an indoor or outdoor wireless siren designed for
installation in areas in which wiring action is difficult or
impossible.
The siren communicates with the PowerMax+ wireless alarm
control system. When an identified activation command is received
from the alarm system, the siren activates its sounder, activates its
flash light (strobe light, every 1.5 seconds) and acknowledges its
activation to the PowerMax+.
The MCS-700 and the alarm control system should be located in
the same house.
MCS-700 Features
•
•
•
•
•
Designed for indoor or outdoor use
The siren has double plastic cover for extra protection against
rain and sun.
Distinguishable siren fire and burglar alarms
Fire alarm: Alternating on/off alarm sound.
Burglary alarm: Continuous high/low tone sweep.
Note: The siren is activated for a predefined "Bell Time" (refer to
PowerMax+ programming guide, par. 4.4) according to local
authorities requirements. After this period, the siren sound stops.
Squawk indications
High, mid or low siren squawk (beep) sounds can be used to
indicate PowerMax+ arming (1 squawk) and disarming (2
squawks) by a keyfob (see PowerMax+ user's guide par. 7.13).
Strobe light
When an identified activation command is received from the
alarm system, the siren light flashes (every 1.5 seconds) until
the PowerMax+ is disarmed. When AC power fails (the siren
uses its backup battery) the strobe light is disabled. The siren
can be purchased with red, blue, amber or transparent lens,
according to the desired strobe light color.
AC Power indication LED
When there is AC power supply, the red LED lights. When the
siren uses its backup battery, the LED does not light.
•
Triple Tamper protection
3 tamper switches are included; one on side cover, second touching
the mounting surface and third attached to the closure screw.
•
Rechargeable Ni-Mh backup battery
Enables backup period of 12 hours (standby) / 15 min. (alarm),
if small battery pack is used (supplied with the product), or 24
hours (standby) / 15 min. (alarm), if an optional large battery
pack is used (2 small battery packs in parallel).
Typical Initial charging time is 24 hours.
When the battery voltage is low, low battery message is sent
to the PowerMax+.
Figure 1 - External View
•
•
2-way full supervision
The siren is fully supervised, 2-way communication device. It
includes a receiver, to receive activation commands from the
alarm system, and a transmitter, to periodically transmit its
status signal to the alarm system.
The transmitted signal strength can be measured during the
installation (refer to PowerMax+ programming guide, section
9 – Diagnostic Test).
Self-test feature
Upon pressing the MCS-700 self test switch for 3 seconds,
the siren functional check is performed (low level sounds and
strobe light indicate that that siren is serviceable).
Remote commander
Emergency pendant
transmitter
Wireless
siren
Door or window
open/close detector
Universal perimeter
protection detector
Smoke detector
POWERMAX+
CONTROL
PANEL
Motion detector
Hard wired detector
Figure 2- Integration with the Alarm System
2. SPECIFICATIONS
Siren Type: Piezo, 98dB SPL @ 1m, 1.8-2.3 kHz, sweep
frequency 7Hz
Power Supply: Indoor, limited power source, plug-in transformer
(supplied with the siren):
120 VAC, 60 Hz / 9 VAC, 700 mA (in the U.S.A.), or 230
VAC, 50 Hz / 9 VAC, 700 mA.
Backup Battery:
Ni-Metal, 7.2V, 250mAh (small battery pack, supplied with the
siren) or 500 mAh (optional large battery pack)
Current Consumption:
13 mA ± 10% (standby), 370 mA ± 10% (operation)
DE5420
Compliance with Standards:
EN 50131-1 (class 2), ETSI EN 300 220, FCC Part 15, IP55
Operating Frequency (MHz): 315, 433.92, 868.95, or 869.2625.
Receiver and Transmitter ID Type: 24-bit
Strobe Output: Pulsed @ 1.5 sec.
Dimensions (LxWxD): 30 x 19 x 7 cm (11-13/16 x 7-1/2 x 2-3/4 in)
Color: White (with red, blue, amber or transparent lens)
Operating Temperature: -20°C to 65°C (-4°F to 149°F)
3. INSTALLATION, TESTING AND ENROLLING
220/110
VAC
WARNING
High voltage do not remove
printed board
cover!
Remove screw
and remove cover
Battery
9VAC
Mark and drill 4 holes (as
desired) in mounting surface,
fasten the siren to the surface
with four 6 cm screws.
Battery
A.Connect 9VAC to POWER terminals.
B.Connect the battery to the BAT connector.
Battery
SELF TEST
Press Self-Test switch for
3 seconds. Verify that the
siren sounds (low level
sound) and that the strobe
light flashes.
ENROLLING
Perform siren enrolling in PowerMax+
memory (see PowerMax+ prog.
guide, section 2). When TRANSMIT
NOW is displayed, momentarily press
the siren Self-Test switch.
Figure 3 – Installation, Testing and Enrolling
Notes
a. Pressing the Self-Test switch for 3 seconds is used for testing the siren (by using low level sound) and its strobe light.
b. Pressing the Self-Test switch momentarily is used to enroll the siren in the PowerMax+ memory (The PowerMax+ must
recognize the siren unique identification code for command delivery and supervision).
c. After the enrolling, close the siren cover and perform DIAGNOSTIC TEST, as described in PowerMax+ programming guide section 9.
Interference Prevention
This device complies with FCC Rules Part 15. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference that may be received or that may cause undesired operation.
The digital circuit of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on,
the user is encouraged to eliminate the interference by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one which supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
Changes or modifications not expressly approved by Visonic Ltd. could void the user's authority to operate the equipment.
WARRANTY
Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its
products hereinafter referred to as "the Product" or "Products" to be in conformance with
its own plans and specifications and to be free of defects in materials and workmanship
under normal use and service for a period of twelve months from the date of shipment by
the Manufacturer. The Manufacturer's obligations shall be limited within the warranty
period, at its option, to repair or replace the product or any part thereof. The Manufacturer
shall not be responsible for dismantling and/or reinstallation charges. To exercise the
warranty the product must be returned to the Manufacturer freight prepaid and insured.
This warranty does not apply in the following cases: improper installation, misuse,
failure to follow installation and operating instructions, alteration, abuse, accident or
tampering, and repair by anyone other than the Manufacturer.
This warranty is exclusive and expressly in lieu of all other warranties, obligations or
liabilities, whether written, oral, express or implied, including any warranty of
merchantability or fitness for a particular purpose, or otherwise. In no case shall the
Manufacturer be liable to anyone for any consequential or incidental damages for breach
of this warranty or any other warranties whatsoever, as aforesaid.
This warranty shall not be modified, varied or extended, and the Manufacturer does not
authorize any person to act on its behalf in the modification, variation or extension of this
warranty. This warranty shall apply to the Product only. All products, accessories or
attachments of others used in conjunction with the Product, including batteries, shall be
covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or
otherwise, caused by the malfunction of the Product due to products, accessories, or
attachments of others, including batteries, used in conjunction with the Products.
The Manufacturer does not represent that its Product may not be compromised and/or
circumvented, or that the Product will prevent any death, personal and/or bodily injury
and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the
Product will in all cases provide adequate warning or protection. User understands that a
properly installed and maintained alarm may only reduce the risk of events such as
burglary, robbery, and fire without warning, but it is not insurance or a guarantee that
such will not occur or that there will be no death, personal damage and/or damage to
property as a result.
The Manufacturer shall have no liability for any death, personal and/or bodily injury
and/or damage to property or other loss whether direct, indirect, incidental,
consequential or otherwise, based on a claim that the Product failed to function.
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or
damage arising under this limited warranty or otherwise, regardless of cause or origin, the
Manufacturer's maximum liability shall not in any case exceed the purchase price of the
Product, which shall be fixed as liquidated damages and not as a penalty, and shall be
the complete and exclusive remedy against the Manufacturer.
Warning: The user should follow the installation and operation instructions and among
other things test the Product and the whole system at least once a week. For various
reasons, including, but not limited to, changes in environmental conditions, electric or
electronic disruptions and tampering, the Product may not perform as expected. The user
is advised to take all necessary precautions for his /her safety and the protection of
his/her property.
6/91
VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788
VISONIC INC. (U.S.A.): 10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: (860) 243-0833, (800) 223-0020 FAX: (860) 242-8094
VISONIC LTD. (UK): FRASER ROAD, PRIORY BUSINESS PARK, BEDFORD MK44 3WH. PHONE: (0870) 7300800 FAX: (0870) 7300801
INTERNET: www.visonic.com
VISONIC LTD. 2004 MCS-700, DE5420- (REV. 2, 01/04)
DE5420

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2004:05:12 13:18:00+03:00
Modify Date                     : 2004:05:12 13:18:00+03:00
Page Count                      : 2
Creation Date                   : 2004:05:12 10:18:00Z
Mod Date                        : 2004:05:12 10:18:00Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : jacob_s
Metadata Date                   : 2004:05:12 10:18:00Z
Creator                         : jacob_s
Title                           : Microsoft Word - DE5420-2_W2002_.doc

EXIF Metadata provided by EXIF.tools