Visonic PWRMCOMPLETEV2 Control panel of wireless alarm control system User Manual manual

Visonic Ltd. Control panel of wireless alarm control system manual

manual

 D-300886  1 PowerMaxComplete User Guide Table of Contents Quick Guide To Primary Alarm Control Operations...........................................................2 Contact list form..................................................2 Luminous Indicator Signals...............................2 Siren Signals.......................................................3 Useful Hints For PowerMaxComplete  Users.3 1. Introduction.................................................... 4 Overview..............................................................4 System Features ................................................5 Terms of the Trade.............................................6 Control Pushbuttons...........................................6 Multi-Function Transmitter ................................7 Voice Announcements.......................................7 Screen Saver Option..........................................7 2. Securing The Protected Site ......................... 8 Security-Related Pushbuttons ..........................8 Preparing to Arm ................................................8 Arming ‘AWAY’ ...................................................8 Arming ‘HOME’ ...................................................8 Switching from ‘HOME’ to ‘AWAY’...................8 Switching from ‘AWAY’ to ‘HOME’...................9 Arming ‘Instant’...................................................9 Forced Arming ....................................................9 Arming in the Latchkey Mode .........................10 Initiating a Panic Alarm....................................10 Initiating Fire Alarm ..........................................10 Initiating Emergency Alarm .............................10 Disarming and Stopping Alarms.....................10 Siren Behavior ..................................................11 3. Speech And Sound Control......................... 12 Speech & Sound Cont. Push-buttons............12 Adjusting the Speech Volume.........................12 Voice ON/OFF ..................................................12 Recording a Message......................................12 Message Playback ...........................................13 Chime ON/OFF.................................................13 4. Electrical Appliance Control ....................... 14 Control Options and Pushbuttons ..................14 Automatic ON/OFF Control.............................14 5. Reading Alarm Memory And Trouble Data. 15 Reviewing Alarm/Tamper Memory.................15 Reviewing Trouble Information.......................15 Reviewing Memory & Troubles at the Same Time ...................................................................16 Correcting Trouble Situations .........................16 6. Special Functions.........................................17 Looking after People Left at Home................ 17 Emergency Calls for Help............................... 17 Remote Control by Telephone....................... 17 Reporting to Private Telephone..................... 18 Remote Control by SMS................................. 19 Reporting by SMS............................................ 19 Reporting Messages to a Pager .................... 20 Conducting a Walk Test.................................. 20 7. User Settings ................................................21 What are the Settings You Need?................. 21 Entering the User Settings Menu................... 21 Bypassing Zones ............................................. 22 Reviewing the Bypassed Zone List ............... 22 Recalling the Last Bypass Scheme............... 23 Programming 4 Telephone Numbers............ 23 Setting the User Codes................................... 23 Enrolling Keyfob Transmitters........................ 25 Deleting Keyfob................................................ 26 Enrolling Proximity Tags (optional)................ 26 Deleting Proximity Tags.................................. 26 Setting the Voice Options ............................... 27 Automatic Arming Option................................ 27 Setting Arming Time........................................ 27 Enabling the Squawk Option.......................... 27 Setting Time and Time Format ...................... 28 Setting the Date and Date Format................. 28 Scheduler Function.......................................... 29 Installer Mode................................................... 29 8. Reading The Event Log................................30 Event Log Description..................................... 30 Reading Procedure.......................................... 30 9. Maintenance..................................................31 Replacing the Backup Battery........................ 31 Replacing Wireless Devices Batteries .......... 31 Periodic Testing ............................................... 32 Cleaning the Control Panel ............................ 32 10. Performance Limits....................................33 APPENDIX A. GLOSSARY................................34 APPENDIX B. HOME FIRE ESCAPE PLANNING........................................................................36
2  D-300886 Quick Guide To Primary Alarm Control OperationsQuick Guide To Primary Alarm Control OperationsQuick Guide To Primary Alarm Control OperationsQuick Guide To Primary Alarm Control Operations    QUICK REFERENCE TO PRIMARY ALARM CONTROL OPERATIONS Arming AWAY ........................................+ + [Code]*  Arming AWAY-INSTANT ........................+ + [Code]* + + Arming HOME ........................................+ + [Code]*  Arming HOME-INSTANT .......................+ + [Code]* + +    Arming AWAY-LATCHKEY ...................+ + [Code]* + + Force Arming AWAY (system not ready) + + [Code]* + + (to silence the protest buzz)  Force Arming HOME (system not ready)+ + [Code]* + + (to silence the protest buzz) Disarming and stopping alarms............+ + [Code] * The factory default master user code is 1 1 1 1. The code is not required if quick arming has been permitted by the installer. Change the factory default code to a secret code without delay (see section 7) Contact list formContact list formContact list formContact list form    Dear Customer, Thank you for choosing PowerMaxComplete, a highly advanced wireless alarm control system produced by Visonic Ltd.  Please note below the installer's telephone number to facilitate obtaining assistance. Company Name: ____________________________ Telephone Number: __________________________ Person to Contact: ___________________________ Also please make sure that you have the name and telephone number of the central station your system will report to. If you ever call the central station to ask questions, you should be able to come up with your "ACCOUNT NUMBER" used to identify your alarm system to the central station. Obtain this information from your installer and write it.  Monitoring Station’s Name _____________________ Telephone Number: __________________________ My Account Number: _________________________ If your system was set by the installer to contact private telephone numbers, note down the 4 telephone numbers that your installer programmed to be called: Phone No. 1: _______________________________ Phone No. 2: _______________________________ Phone No. 3: _______________________________ Phone No. 4: _______________________________  Luminous Indicator SignalsLuminous Indicator SignalsLuminous Indicator SignalsLuminous Indicator Signals    Indicator Behavior Significance  (red)  Lights steadily Flashes No light The system is in the armed state (AWAY MODE) The system is in the armed state (HOME MODE) The system is presently in the disarmed state  (orange)  Lights steadily No light A state of trouble is presently being detected No trouble - all is well  (green)  Lights steadily No light The chime function is active - chime zones will chime when disturbed. The chime function is inactive - chime zones will not chime when disturbed.  (green)  Lights steadily No light AC power is supplied to the control panel The system is operating on backup battery power
 D-300886  3 Siren SignalsSiren SignalsSiren SignalsSiren Signals    Alarm Type Graphic Representation of Signal Verbal Description of Signal Burglar / 24 hour/ Panic  ––––––––––––––––––––––––––––––– ON continuously Fire  – – –    – – –     – – –     – – – .................  ON - ON - ON - pause - ON - ON - ON - pause ..... Test*  –– (both external and internal sirens)  ON for 2 seconds (once) * Supplementary use only. Useful Hints For PowerMaxComplete  UsersUseful Hints For PowerMaxComplete  UsersUseful Hints For PowerMaxComplete  UsersUseful Hints For PowerMaxComplete  Users     Stopping an alarm: When the alarm sounds - press the DISARM ( ) button on your key-ring transmitter or press  on the keypad and then enter your access code (1 1 1 1 by default). Stopping trouble beeps: When trouble occurs in the system, the TROUBLE indicator on the front panel will light, and a sequence of 3 beeps will sound once per minute. If you do not wish to eliminate the trouble immediately and the beeps are bothersome, press the DISARM ( ) button on your key-ring transmitter, or press  on the keypad and then enter your access code (1 1 1 1 by default). This will silence the buzzer for 4 hours, after which the trouble beeps will resume sounding. Be advised, however, that in any case the trouble beeps are silenced during night hours. Perimeter and interior zones versus 24-hour zones: Most of the protection sensors in your system are linked to perimeter and interior zones. These zones trigger alarms while the system is in the armed state and do not trigger alarms while the system is in the  disarmed  state. Other sensors are linked to 24-hour zones which trigger alarms irrespective of arming/disarming.  Arming while perimeter zones are not secured (doors and/or windows are open): Your display will read “NOT READY” if a protected door or window is open. You can find out which zone is “not ready” by clicking the   button. You can eliminate the problem by closing the door/window or by performing "Forced arming" (zone deactivation) if this option was enabled by the system installer. In case you intentionally choose to bypass a zone, leave the door or window open and arm the system (a voice message will announce that ”Forced Arming” is under way - not applicable in PowerMaxComplete that does not have VOICE option). Bypassed zones will not be protected during one arming period.  Gaining access to 24-hour zones: If you wish to access a sensor defined as a 24-hour zone without causing an alarm: •  Click   - the display will read: NORMAL MODE. •  Click   again - the display will read: USER SETTINGS.  •  Click   - the display will read: ENTER CODE ___. Key your secret 4-digit <User Code> - the buzzer will play the “happy tune” (- - - ––––). You have 4 minutes during which the 24-hour sensor can be opened and accessed. When the 4 minutes are up, the system will automatically revert to the normal mode. Canceling accidental alarms: Upon alarm, the internal sounder is activated first for a limited period of time (set by the installer). Then the external siren starts and the event is reported to the central monitoring station. If you accidentally cause an alarm, you may simply disarm the system before the external siren starts - the alarm will not be reported. If you cause an alarm accidentally and the external siren has already started - you can still disarm the system within a time limit set by the installer (1 to 15 minutes, as desired). If you manage to disarm on time, a  CANCEL ALARM message will be automatically sent to the central monitoring station. Failing to exit before the exit delay expires: If you exit the protected site after the exit delay expires (the exit delay beeps stop), the system will interpret this as if you just entered. The entry delay countdown will begin and the entry delay beeps will sound. To prevent an alarm, you must disarm the system before the entry delay expires. Unauthorized entry took place while you were away: If you hear alarm sirens when you are about to re-enter the premises, and lights which should be off are on - an intruder may still be inside or another event may have occurred. Do not confront the intruder - remain outside and call the emergency services.
INTRODUCTION  4  D-300886 1. Introduction1. Introduction1. Introduction1. Introduction    OverviewOverviewOverviewOverviewThe PowerMaxComplete  is a wireless alarm control system that provides protection against burglary, fire and tampering. In addition, it can be used to control a light or an electrical appliance within your household and/or to monitor the activity of disabled or elderly people left at home. Status information is presented visually and verbally, and in most cases a recorded voice prompts you to take correct action - not applicable in PowerMaxComplete that does not have VOICE option. The PowerMaxComplete  is governed by a control panel (Figure 1) designed to collect data from various sensors that are strategically located within and along the perimeter of the protected site (Figure 2).  In the disarmed state, the system provides you with visual and verbal status information, and initiates an alarm if smoke is detected or upon disturbance in a 24-hour zone (a zone which is active 24-hours a day). In the armed state, the system will initiate an alarm upon detection of disturbance in any one of the armed zones. You will need a 4-digit security code to master the system (code 0000 is disallowed), and you can authorize 7 other persons to use the system by providing them with their own security codes. Moreover, you can obtain up to 8 multi-function key-ring transmitters and proximity tags that  will allow you and other users to easily control major functions.  Proximity tags enable authorized people to enter restricted areas. Presenting valid proximity tag, while the system is armed, causes the system to disarm. Presenting valid proximity tag, while the system is disarmed, causes the system to be armed in AWAY (optional HOME) mode.  The system identifies a wide range of events - alarms, attempts to tamper with sensors and several types of trouble. Events are automatically reported via the public telephone network or GSM network to central monitoring stations (in digital form) and to private telephones (in plain language and/or SMS messages). The person receiving such a message is expected to investigate the event and act accordingly. CONTROLKEYSKEYPADCOVER(CLOSED)DISPLAY Figure 1. Control Panel with Covers Closed IMPORTANT! All you need to know to secure your premises can be found in Chapter 2 of this manual. If you are not familiar with some of the terms used here, refer to Appendix A at the end of this guide.
INTRODUCTION D-300886  5 UP TO 8 KEYFOBTRANSMITTERSUP TO 8 WIRELESSREMOTECOMMANDERSPGM OUTPUT FORCONTROLLING DEVICESBY VARIOUS FACTORSAS PROGRAMMEDBY THE INSTALLEREXTERNALGSM UNIT(optional)CEL. TELCENTRAL MONITORINGSTATIONSPUBLICSWITCHINGTELEPHONENETWORK4 PRIVATETELE-PHONESTEL. LINEWIRELESSSIRENSUP TO TWO2-WAY KEYPADSPAGER COMPANYCOMPUTER PAGERSITEEXTERNALSIRENSEMERGENCYPENDANTTRANSMITTERSWIRELESSDETECTORS(UP TO 28 UNITS)INSTALLED  INTHE PROTECTEDPREMISESSMOKEDETECTORUNIVERSALPERIMETERPROTECTIONDETECTORDOOR ORWINDOWOPEN/CLOSEDETECTORMOTIONDETECTORFLOODDETECTORGASDETECTORUP TO 2HARD WIREDDETECTORSUP TO 8PROXIMITYTAGS(optional)SITE INTERNALSIREN ORSTROBELOCALCOMPUTER(OPTION)LOCALEXCHANGEGSMNETWORKCO GASDETECTOR Figure 2. System Configuration System FeaturesSystem FeaturesSystem FeaturesSystem Features    Your PowerMaxComplete  offers a large number of unique features: •  30 zones: Each protected zone is identified by number and by name (ask your installer to assign names to your zones). •  Multiple arming modes: AWAY, HOME, AWAY- INSTANT, HOME-INSTANT, LATCHKEY and BYPASS. •  Liquid crystal display (LCD): Plain-language status information and prompts are displayed on the front panel in large, clear letters. •  Real-time clock: The present time is visible on the display. •  Various reporting destinations: Events are reported automatically to central monitoring stations, private telephones of your choice and even to a pager. •  Selective reporting: Your installer can determine what type of event will be reported to which destination. •  Latchkey mode: An automatic “Latchkey” message is sent to chosen telephones if the system is disarmed by a “latchkey” user (a junior family member, for instance). •  Spoken announcements and instructions (not applicable in PowerMaxComplete that does not have VOICE option): Status- dependent, pre-recorded verbal messages are heard over the built-in loudspeaker (if the voice prompts are enabled - see chapter 7).  •  Message exchange (not applicable in PowerMaxComplete that does not have VOICE option):  Before leaving the premises, you may record a short verbal message for other users of the system who may arrive later. Upon arrival, you can listen to verbal messages left by others for you.   •  Keypad and wireless control: Full control from the keypad; major functions can be carried out by pressing buttons on hand-held miniature transmitters.
INTRODUCTION   6  D-300886 •  Access from remote telephones: You may access the PowerMaxComplete  from a remote telephone and Arm/Disarm it or receive system status information.  •  Numerical keys serve as function keys: In the disarmed state, numerical keys are used to control various system functions. A simple icon on each key identifies the task of that key. •  PGM remote control: Gate control mechanisms, courtesy lights and various other devices can be switched on and off via a special PGM (programmable) output. Your installer will determine the control means, in accordance with your needs. •  Data retrieval: You can obtain status information, trouble information and review memorized alarm events - visually and verbally. •  Looking after elderly, physically handicapped and infirm individuals:  The system can be programmed to monitor activity within the protected area and send out an alert message if the person under surveillance remains still for too long.  •  Distress calls: Miniature pushbutton transmitters dealt out to specific individuals may be used for sending emergency calls for help. •  Disarming under duress: If a user is forcibly compelled to disarm the system, he can use a special code that disarms the system apparently as usual, but sends a silent alarm to the central station (see chapter 2). •  System supervision: All wireless detectors and wireless commanders within the protected site send periodic supervision messages. If such a message is overdue, the PowerMaxComplete  displays an ‘inactivity’ trouble message. Your installer can disable this feature if so desired. •  Battery supervision: You do not have to worry about ‘dead’ batteries. The PowerMaxComplete  displays a ‘Low Battery’ message whenever a battery in a wireless device is found to be near the end of its useful life. Terms of the TradeTerms of the TradeTerms of the TradeTerms of the Trade    Better understanding of your system is assured if you take time to read the definitions in APPENDIX A at the end of this manual. However, if this is not your first alarm system, then simply read on. Control PushbuttonsControl PushbuttonsControl PushbuttonsControl Pushbuttons    When the keypad cover is closed, as shown in Figure 1, only two pushbuttons are visible - the top panel controls:   Key  Task Advance from item to item within a given menu. Review status messages one by one and also select a displayed option. With the keypad uncovered (see Figure 3), the special-function keys are visible. The tasks of these keys are explained in the relevant sections of this guide.  VOLUME UP (*)EMERGENCY(Hold for 2 sec.)PLAY MESSAGE (*)VOLUME DOWN (*)CHIME ON/OFFMUTE SPEAKER (*) (**)EVENT LOGCANCEL ENTRY DELAYRECORD MESSAGE (*)ARM TROUBLECHIMEPOWERPGM OUTPUT ONPGM OUTPUT OFFPGM CONTROLTESTINGARMING “AWAY”ARMING “HOME”DISARMINGMOVE BACKFIRE (Holdfor 2 sec.)Press bothfor panicalarmSHOW/OKNEXTINDICATORSDISPLAY Figure 3. Controls and Indicators *   May not be functional on all versions of PowerMaxComplete. **  The Mute Speaker button   is active only if the "Set Voice Option" function is enabled ("enable prompts" - see user setting flow-chart, fig. 8).
INTRODUCTION D-300886  7 MultiMultiMultiMulti----Function TransmitterFunction TransmitterFunction TransmitterFunction Transmitter    Your system responds to signals sent by a 4-button, MCT- 234 miniature ‘keyfob’ transmitter that you and other users can carry (see figure 4). Your installer can program the AUX (auxiliary) buttons to perform various tasks, as required. DISARMAWAYAUXHOME MCT-234 Figure 4. Keyfob Transmitters Pressing AWAY and HOME together for 2 sec. initiates PANIC alarm. Pressing AWAY twice within 2 seconds initiates Latchkey arming. A. Controlling a gate or another electrical device:  Pressing the AUX button opens/closes an electrically-controlled gate, or controls a chosen electrical device.  B.  Arming the system in the INSTANT mode (without an entry delay): Pressing the AUX button immediately after arming, during exit delay, causes the system to be armed without an entry delay. This means that entering the protected premises via any zone will trigger an immediate alarm. You and other holders of keyfob transmitters will have no problem, because you can disarm the system before entering by pressing the DISARM ( ) button on your transmitter before entry.  C.  Getting status information: Upon pressing the AUX button on your transmitter, the voice module   announces the system status over the loudspeaker - not applicable in PowerMaxComplete that does not have VOICE option.    Disarming by a keyfob whose battery voltage is low If you try to disarm the system with a keyfob whose battery voltage is low, a protest beep will be heard for 15 seconds (if this beep is enabled by the installer). During this period you should press again the disarm button of the keyfob or control panel (for the control panel, user code is required) to disarm the system. If you perform this action during the 15 seconds period, the Low Bat message will be stored in the event log. If the disarm button is not pressed again during the 15 seconds period, perform either of the following actions: A.  Press AWAY twice to arm the system, otherwise the system will not be armed and an acknowledgement (from the user that he knows about the Low Bat) will not be stored in the event log.   B. Press AWAY and then press disarm button, to acknowledge, otherwise the acknowledgement will not be stored in the event log. Voice AnnouncementsVoice AnnouncementsVoice AnnouncementsVoice Announcements    (Not applicable in PowerMaxComplete that does not have VOICE option). The pre-recorded voice announcements respond to your commands by announcing what the system is doing and by prompting you to perform certain actions. They also announce alarms, troubles and identify the source of each event. Screen Saver OptionScreen Saver OptionScreen Saver OptionScreen Saver Option    The Screen Saver option (if enabled by the installer) causes that when no key is pressed during more than 30 seconds, the display is “PowerMax” and the LEDs do not light (to prevent an intruder to know the system status). The normal display returns after pressing the   button followed by entering user code (Refresh by Code) or after pressing any key (Refresh by Key), as selected by the installer.  If Refresh by Key was selected, the first pressing of any key (except Fire and Emergency) causes normal display return and the second press performs the key function. Regarding the Fire and Emergency keys, the first key press causes normal display return and also performs the Fire/Emergency function.
SECURING THE PROTECTED SITE 8  D-300886 2. Securing The Protected Site2. Securing The Protected Site2. Securing The Protected Site2. Securing The Protected Site    SecuritySecuritySecuritySecurity----Related PushbuttonsRelated PushbuttonsRelated PushbuttonsRelated Pushbuttons    Key Function  Arming when nobody is at home  Arming when people remain at home  Canceling the entry delay upon arming (‘AWAY-INSTANT’ or ‘HOME-INSTANT’)  Disarming the system and stopping alarms  Testing the system (see Chapter 6 - Conducting Walk Test). Preparing to ArmPreparing to ArmPreparing to ArmPreparing to Arm    Before arming, make sure that READY is displayed: READY             HH:MM If Ready is displayed, all zones are secured, and you may arm the system any way you choose.  If at least one zone is open (disturbed), the display will read: NOT READY      HH:MM If  NOT READY is displayed because of unsecured zone, click   to review the numbers and names of all open zones one by one.  Let us assume that zone 2 (the back door) and zone 13 (the kitchen) are open. To investigate, proceed as follows: PRESS RESULTANT DISPLAY NOT READY      HH:MM  BACK DOOR      (alternating)        Z2 OPEN KITCHEN      (alternating)        Z13 OPEN ! (after 10 seconds) ! None (see note below)  NOT READY      HH:MM Note: To quit immediately at any stage, press   .   It is highly recommended to fix the open zone(s), thus restoring the system to the state of “ready to arm”. If you do not know how to do this, consult your installer. IMPORTANT! All arming procedures below are based on the assumption that quick arming has been enabled by the installer. If quick arming is disabled, the PowerMaxComplete  will prompt you to enter your security code before arming. Arming ‘AWAY’Arming ‘AWAY’Arming ‘AWAY’Arming ‘AWAY’    If the system is READY, proceed as shown: PRESS RESULTANT DISPLAY  ARMING AWAY  ↓   PLEASE EXIT NOW Vacate the premises  ↓     (Exit delay)      ↓  AWAY  ARM indicator lights steadily during the armed state. Arming ‘HOME’Arming ‘HOME’Arming ‘HOME’Arming ‘HOME’    If all perimeter zones are READY, and quick arming is allowed, proceed as shown: PRESS RESULTANT DISPLAY  ARMING HOME Move to interior zone  ↓     (Exit delay)      ↓  HOME   HH:MM  ARM indicator flashes during the armed state. Switching from ‘HOME’ to ‘AWAY’Switching from ‘HOME’ to ‘AWAY’Switching from ‘HOME’ to ‘AWAY’Switching from ‘HOME’ to ‘AWAY’    Do not disarm the system - just press  . The response will be the same as in ARMING AWAY above. Vacate the premises before the exit delay expires.
SECURING THE PROTECTED SITE D-300886  9 Switching from ‘AWASwitching from ‘AWASwitching from ‘AWASwitching from ‘AWAY’ to ‘HOME’Y’ to ‘HOME’Y’ to ‘HOME’Y’ to ‘HOME’     Do not disarm the system - just press  . Since this operation reduces the security level, the PowerMaxComplete  will ask you to key in your master user code or user code, thus making sure that you are an authorized user. PRESS RESULTANT DISPLAY  ENTER CODE     _ _ _   ARMING HOME ↓ (Exit delay) ↓ [Enter code] Move to interior zone ARM HOME      HH:HH  ARM indicator flashes during the armed state. If an alarm occurred while the system was armed in the AWAY mode, the display will respond differently: PRESS RESULTANT DISPLAY  ENTER CODE   _ _ _ [Enter code] ARMING HOME ↓ (Exit delay) ↓ Move to interior zone HOME      HH:HH       (alternating)        ARM HOME MEMORY  ARM indicator flashes during the armed state. Arming ‘InsArming ‘InsArming ‘InsArming ‘Instant’tant’tant’tant’    You may arm AWAY or HOME without an entry delay - any detection in any zone will trigger an immediate alarm. If you wish to arm AWAY-INSTANT, proceed as follows. PRESS RESULTANT DISPLAY  ARMING AWAY   ARMING INSTANT      (alternating)         PLEASE EXIT NOW ↓ (Exit delay) ↓ Vacate the premises AWAY  ARM indicator lights during the armed state.   If you wish to arm HOME-INSTANT, proceed as follows: PRESS RESULTANT DISPLAY  ARMING HOME ARMING INSTANT      (alternating)        ARMING HOME ↓ (Exit delay) ↓ ARM HOME      HH:HH      (alternating)       Go to an internal zone ARM HOME INSTANT  ARM indicator flashes during the armed state. Forced ArmingForced ArmingForced ArmingForced Arming    Forced arming allows you to arm the system even though one zone or several zones are disturbed, and the NOT READY message is displayed.  Automatic forced arming only works if the installer allowed this option while programming your system. Disturbed zones will be bypassed - they will not be armed. The protected site will not have maximum protection. Note: When forced arming is carried out, the buzzer “protests” by emitting a continuous tone during the exit delay until the last 10 seconds of the delay. You can silence this signal by pressing the arming button again. When NOT READY is displayed, Forced arming “AWAY” is performed as follows: PRESS RESULTANT DISPLAY  ARMING AWAY  ↓   PLEASE EXIT NOW ↓     (Exit delay)      ↓       (to mute the buzzer) AWAY    ARM indicator lights during the armed state. When NOT READY is displayed, Forced arming “HOME” is performed as follows: PRESS RESULTANT DISPLAY  ARMING HOME ↓ (Exit delay) ↓ HOME      HH:HH           (To mute the buzzer)Go to interior zone ARM indicator flashes during the armed state.
SECURING THE PROTECTED SITE 10  D-300886 Arming in Arming in Arming in Arming in the Latchkey Modethe Latchkey Modethe Latchkey Modethe Latchkey Mode    This mode is useful for a parent at work who wants to be sure that his children have returned from school and have disarmed the system. Arming in the “latchkey” mode means that a special “latchkey” message will be sent out when the system is disarmed by a “latchkey user”.  Latchkey users are holders of user codes 5 through 8 or users of Keyfob transmitters 5 through 8. The latchkey message is considered an alert and not an alarm, and is therefore sent to the private telephones programmed by the user as targets for alert messages. Latchkey arming is possible only when you arm “AWAY”. To arm in the Latchkey mode, proceed as follows: PRESS RESULTANT DISPLAY  ARMING AWAY    ARMING LATCHKEY (Within 2 seconds)      (alternating)         PLEASE EXIT NOW Vacate the premises  ↓ (Exit delay) ↓  AWAY  ARM indicator lights during the armed state. Initiating a Panic AlarmInitiating a Panic AlarmInitiating a Panic AlarmInitiating a Panic Alarm    You can generate a panic alarm manually in the disarmed and armed states alike. If this feature has been enabled by the installer (consult your installation company to determine if it has been enabled).The sequence will be as shown: PRESS RESULTANT DISPLAY PANIC ALARM Then, if or when the system is in the disarmed state:    (Pressed simultaneously) READY        HH:MM Note: If you are using a key-ring transmitter, press both AWAY and HOME buttons simultaneously for 2 seconds. To stop the alarm, press  and then key in your valid user code. Initiating Fire AlarmInitiating Fire AlarmInitiating Fire AlarmInitiating Fire Alarm    (This function is disabled in ACPO compliant version). You can generate a fire alarm manually (depends on the purchased PowerMaxComplete  version - see PowerMaxComplete  door label) in disarmed & armed states, as follows:  PRESS RESULTANT DISPLAY FIRE Then, if or when the system is in the disarmed state:  READY        HH:MM To stop the alarm, press   and then key in your valid user code. Initiating Emergency AlarmInitiating Emergency AlarmInitiating Emergency AlarmInitiating Emergency Alarm    You can generate an emergency alarm manually (depends on the purchased system version - see PowerMaxComplete  door label) in the disarmed and armed states as follows: PRESS RESULTANT DISPLAY EMERGENCY Then, if or when the system is in the disarmed state:  READY        HH:MM To stop the alarm, press    and then key in your valid user code. Disarming and Stopping AlarmsDisarming and Stopping AlarmsDisarming and Stopping AlarmsDisarming and Stopping Alarms    (This function is disabled in ACPO compliant version). Disarming the system stops the siren before it stops automatically, irrespective of whether the alarm was initiated in the armed or the disarmed state.  After disarming, different displays may appear, depending on the current status of the system: A. Disarming - no events: After an uneventful armed term, the disarming operation will progress as shown: PRESS RESULTANT DISPLAY  CODE     _ _ _ [Enter code] READY      HH:MM  ARM indicator extinguishes B. Disarming after alarm, with all zones ready: If the zone that alarmed in the armed state is back to normal, the disarming operation will as shown: PRESS RESULTANT DISPLAY  CODE     _ _ _  code READY      HH:MM       (alternating)        READY MEMORY   ARM indicator extinguishes.
SECURING THE PROTECTED SITE D-300886  11  To read the alarm memory, refer to Chapter 5. The "MEMORY" message will disappear only upon re-arming the system. C. Disarming after an alarm, with one zone still disturbed: If the zone that alarmed in the armed state is still disturbed, the disarming operation will progress as shown: PRESS RESULTANT DISPLAY  CODE     _ _ _  CODE NOT READY    HH:MM       (alternating)        NOT READY MEMORY ARM indicator extinguishes To read the alarm memory, refer to Chapter 5. The "MEMORY" message will disappear only when you rearm the system. If you do not know how to return the disturbed zone to normal, consult your installer. D. Disarming with the system in a state of trouble: If trouble is detected in the armed state, the TROUBLE indicator on the front panel will light and the disarming operation will progress as shown: PRESS RESULTANT DISPLAY  CODE     _ _ _   CODE READY    HH:MM       (alternating)        READY TRBL  ARM indicator extinguishes and   sounds once per minute, To find out what kind of trouble is being sensed, see Chapter 5. The TRBL display will disappear, the  TROUBLE  indicator will extinguish and the trouble beeps will stop upon eliminating the cause for trouble.  E. Disarming after an alarm, with the system in a state of trouble: The TROUBLE indicator on the front panel will light. If the zone that alarmed while the system was in the armed state is back to normal, the disarming operation will progress as shown: PRESS RESULTANT DISPLAY  CODE     _ _ _ CODE READY    HH:MM       (alternating)        READY TRBL       (alternating)        READY MEMORY  ARM indicator extinguishes and   sounds once per minute. To find out which zone alarmed and what kind of trouble is being sensed, see Chapter 5. The TRBL display will disappear, the TROUBLE indicator will extinguish and the trouble beeps will stop upon eliminating the cause for trouble. The MEMORY message will disappear only upon rearming the system. F. Disarming under Duress. If you are forcibly compelled to disarm the system, enter the default duress code (2580) or another code set by the installer. Disarming will take place normally but a silent alarm will be transmitted to the central station. Siren BehaviorSiren BehaviorSiren BehaviorSiren Behavior    Continuously ON when initiated by a burglar zone or a 24-hour zone, and when a user initiates a “panic alarm”. When initiated by a fire zone (smoke is detected) ON - ON - ON - pause - ON - ON - ON - pause - ........ and so on. If there is nobody around to disarm the system upon alarm and a zone remains "open", the siren will sound for the time duration set by the installer - then will stop. The strobe light keeps flashing until the system is disarmed.
SPEECH AND SOUND CONTROL 12  D-300886 3. Speech And Sound Control 3. Speech And Sound Control 3. Speech And Sound Control 3. Speech And Sound Control     (In PowerMaxComplete that does not have VOICE option, the SPEECH and VOICE features are not applicable, only the CHIME feature is applicable). Speech & Sound Cont. PushSpeech & Sound Cont. PushSpeech & Sound Cont. PushSpeech & Sound Cont. Push----buttonsbuttonsbuttonsbuttons    The sound and speech-related functions offered by the PowerMaxComplete  are controlled with the keypad, as detailed in the following list. Key Function   Increasing the loudness of spoken messages    Decreasing the loudness of spoken messages   Enabling / disabling the loudspeaker  Recording a spoken message for other users of  the alarm system  Listening to a recorded message left by another user of the alarm system  Enabling / disabling the chime function in chime zones Adjusting the Speech VolumeAdjusting the Speech VolumeAdjusting the Speech VolumeAdjusting the Speech Volume    The following diagram shows how to increase the loudness by clicking the <1> key (assuming that the volume was at minimum to begin with). PRESS RESULTANT DISPLAY   VOLUME+      VOLUME+         VOLUME+          (max) VOLUME+           The following diagram shows how to decrease the loudness with the <4> key (assuming that the volume was at maximum to begin with). PRESS RESULTANT DISPLAY   (max) VOLUME–               VOLUME–            VOLUME–           VOLUME–     Voice ON/OFFVoice ON/OFFVoice ON/OFFVoice ON/OFF    You can switch spoken announcements on and off by alternate clicking of the <7> key, as shown below. PRESS RESULTANT DISPLAY  VOICE ON  VOICE OFF  ↓  READY    HH:MM Note: The system will maintain the “Voice OFF” state until subsequent selection of “Voice ON’. Recording a MessageRecording a MessageRecording a MessageRecording a Message    You can leave a verbal message for other users of the alarm system. Face the panel, press <2> and keep it pressed. When the display reads TALK NOW, start talking. The 5 dark boxes will slowly disappear one by one, from right to left, as shown in the diagram below.  ACTION RESULTANT DISPLAY  (constant) RECORD A MESSAGE Talk ↓ TALK NOW           Talk ↓ TALK NOW        Talk ↓ TALK NOW      Talk ↓ TALK NOW      Talk ↓ TALK NOW    Stop talking RECORDING ENDED Once the last of the boxes disappears, RECORDING ENDED will be displayed.
SPEECH AND SOUND CONTROL D-300886  13  When you release the button, the display will revert to the normal status-displaying mode, but will also indicate that a message is waiting. For example: READY             HH:MM      (alternating)        READY             MSG To check your own message, listen to it within one minute from the end of recording (see Chapter 3 - Message Playback). This way the MSG  indication will not be erased. Message PlaybackMessage PlaybackMessage PlaybackMessage Playback    To listen to a message left by another user of the system:  Click   and listen. PLAY will be displayed and the message will be played back over the built-in loudspeaker. When the playback ends, the display will revert to the normal status-displaying mode. If more than 1 minute elapsed after recording, the MSG indication will disappear. Chime ON/OFFChime ON/OFFChime ON/OFFChime ON/OFF    You can disable / enable the chime zones by alternate clicking of the <8> key, as shown below: PRESS RESULTANT DISPLAY  CHIME ON  CHIME OFF  ↓  READY    HH:MM  CHIME indicator lights steadily when “chime on” is selected.
ELECTRICAL APPLIANCE CONTROL 14  D-300886 4. Electrical Appliance Control4. Electrical Appliance Control4. Electrical Appliance Control4. Electrical Appliance Control  Control Options and PushbControl Options and PushbControl Options and PushbControl Options and Pushbuttonsuttonsuttonsuttons    The system allows manual or automatic remote control of a device connected to the PGM output.  While programming the system, your installer determines ON and OFF times for the device connected to PGM output. He also determines which zone sensors will switch the remote controlled appliance on and off. However, the decision whether the remote controlled appliance will respond as programmed is up to you (see next table).  Key Function  Manual activation of A light or other household electrical appliance that is connected to PGM output.  Manual deactivation of a light or other household electrical appliance that is connected to PGM output.  Selecting the active automatic control method: " Sensors: The appliance is controlled by sensors (assigned by the installer for this).  "  Timer: The appliance is controlled by timer (ON and OFF times are defined by the installer). "  Both: The appliance is controlled by sensors as well as by a timer. Examples of benefits gained by automatic remote control:  •  Timer Control. When you are away, the timed activation / de-activation of an electrical appliance. •  Zone Control.  Upon disturbance of a perimeter zone, the electrical device is switched on. Note: Automatic activation and deactivation of electrical appliance depends also on the Scheduler setup (see Chapter 7 - Scheduler Function). Automatic ON/OFF ControlAutomatic ON/OFF ControlAutomatic ON/OFF ControlAutomatic ON/OFF Control    You can select two of four options:  #### By Timer ON    #### By timer OFF #### By sensor ON    #### By sensor OFF The presently active options are shown with a dark box ( ) at the far right. To view the 2 other options click .  A presently inactive option is shown without a dark box at the far right. The dark box will appear if you click   while the option is displayed. A “Happy Tune” indicates successful saving of a new option.  PRESS RESULTANT DISPLAY BY TIMER ON        (If this is the default) BY TIMER OFF    If not satisfied - press    BY TIMER OFF      If satisfied -  press  BY TIMER OFF       BY SENSOR ON         (If this is the default) BY SENSOR OFF If not satisfied - Press    BY SENSOR OFF    If satisfied -  BY SENSOR OFF      READY    HH:MM
READING ALARM MEMORY AND TROUBLE DATA D-300886  15 5. Reading Alarm Memory And Trouble Data5. Reading Alarm Memory And Trouble Data5. Reading Alarm Memory And Trouble Data5. Reading Alarm Memory And Trouble Data    Reviewing Alarm/Tamper MemoryReviewing Alarm/Tamper MemoryReviewing Alarm/Tamper MemoryReviewing Alarm/Tamper Memory    The PowerMaxComplete  retains in its memory alarm and “tamper” events that occurred during the last arming period.  Note: Alarms enter the memory only after expiry of the “abort period” (see Appendix A). This means that if you disarm the system immediately - before the abort period expires - there will be no memory indication.  A. Alarm / Tamper Indications When the memory contains at least one event and the system is in the disarmed state, a flashing MEMORY message will be displayed as exemplified: READY             HH:MM      (alternating)        READY             MEMORY or, if the system is not ready for arming - NOT READY          HH:MM      (alternating)        NOT READY       MEMORY B. Investigating Alarm/Tamper Data To review memory content, click the   button.  EXAMPLE 1: An alarm was triggered because the garage door - zone No. 12 - opened but then re-closed. In addition, the bedroom motion detector - zone No. 7 - sent a “Tamper” message because its cover had been removed. PRESS RESULTANT DISPLAY READY      HH:MM  Z12  ALARMED        (alternating)         GARAGE DOOR Z07 TAMPER-OPEN        (alternating)         BEDROOM In response to additional clicking of   button, the display shows details of other events retained in memory (if any), or reverts to its initial state  (see A above). EXAMPLE 2: An alarm was triggered because the garage door - zone No. 12 - opened and was left open. PRESS RESULTANT DISPLAY NOT READY      HH:MM  Z12  ALARMED        (alternating)         GARAGE DOOR Z12 OPEN        (alternating)         GARAGE DOOR Remember! The memory indication and content are cleared upon the next arming of the system. Reviewing Trouble InformationReviewing Trouble InformationReviewing Trouble InformationReviewing Trouble Information    A. Trouble Indications If TRBL flashes in the display, the TROUBLE indicator illuminates, and 3 beeps are sounded once per minute, you will have to investigate the system in order to find out the origin and type of trouble. Trouble types are: SENSOR / KEYFOB / WIRELESS COMMANDER TROUBLES •  Inactivity - No radio signals have been received from a particular sensor / wireless commander (if its supervision feature has been enabled) during a pre-defined period. •  Low battery - The battery in a sensor, keyfob or wireless commander is near the end of its useful life. •  "Clean me" - The fire detector must be cleaned. •  Gas trouble - Gas detector failure. •  Siren AC failure - There is no power to the siren.   GSM TROUBLES (if used) •  GSM AC failure - No power to GSM unit. •  GSM low battery - GSM battery voltage is low. •  GSM tamper- Someone tampered with the GSM unit. •  GSM line fail - GSM telephone line failure. •  GSM net fail - GSM network failure. •  RSSI low - The GSM received signal strength is low. •  GSM modem off - The GSM unit does not operate. •  GSM communication fail - There is no communication (RS-232 format) between PowerMaxComplete  and GSM unit.
READING ALARM MEMORY AND TROUBLE DATA 16  D-300886 SYSTEM TROUBLES •  AC Supply Failure - There is no power and the system is working on backup battery power (this trouble is reported 5 minutes after its occurrence). •  System Jammed - A radio-frequency signal is blocking communication channel of sensors and control panel.  •  Communication failure - A message could not be sent to the central monitoring station or to a private telephone (or a message was sent but was not acknowledged). •  CPU low battery - The backup battery within the control panel is weak and must be replaced (see Chapter 9 - Replacing Backup Battery). •  CPU tamper - The control panel is being tampered with. •  Fuse Trouble - The siren fuse is burnt out. IMPORTANT! If the trouble beeps bother you, disarm the system again (even though it is already disarmed). This will cancel the trouble beeps for 4 hours. B. Investigating Trouble Sources In a state of trouble, a flashing TRBL message is displayed as shown in the following examples: READY             HH:MM      (alternating)        READY             TRBL or, if the system is not ready for arming - NOT READY          HH:MM      (alternating)        NOT READY       TRBL You can review the current troubles one by one, by clicking the   button. EXAMPLE: The kitchen sensor - zone No. 9 - has been inactive and the living room sensor - zone No. 15 - has reported a low battery. However, these troubles do not prevent the system from being “ready to arm”. To investigate the source of trouble, proceed as follows: PRESS RESULTANT DISPLAY READY      HH:MM  Z09 INACTIVE        (alternating)        KITCHEN Z15 LOW BATTERY        (alternating)        LIVING ROOM  In response to further clicking of  , the display will show details of other troubles (if any), or will revert to the initial alternating displays (see example above). Reviewing Memory & Troubles at Reviewing Memory & Troubles at Reviewing Memory & Troubles at Reviewing Memory & Troubles at the Same Timethe Same Timethe Same Timethe Same Time    If alarms / tamper events are retained in the alarm memory and at the same time a state of trouble exists, the display will behave as shown below: READY             HH:MM      (alternating)        READY             MEMORY      (alternating)        READY             TROUBLE or, if the system is not ready for arming - NOT READY     HH:MM      (alternating)        NOT READY     MEMORY      (alternating)        NOT READY       TRBL Note (not applicable to PowerMaxComplete that does not have VOICE feature): When a voice message is in memory, the MSG display will also appear (as shown in Chapter 3 - Recording a Message). To read status information - memory data, open zones and trouble sources (in this order) - click the  button repeatedly. The memory content will be displayed first, in the same manner shown in Chapter 5 - Reviewing Alarm / Tamper Memory. If the system is not ready, open zone information will follow in the same manner as shown in Chapter 2 - Preparing to Arm. Trouble sources will be displayed last, in the same manner shown in Chapter 5 - Reviewing Trouble Information. Correcting Trouble SituationsCorrecting Trouble SituationsCorrecting Trouble SituationsCorrecting Trouble Situations    The trouble indications (illuminated TROUBLE indicator and flashing TRBL message) are cleared once you eliminate the cause for trouble. If you do not know how to cope with a trouble situation, report it to your installer and seek his advice. INACTIVITY: Once an inactive sensor or wireless commander renews its periodical transmissions, the inactivity trouble no longer exists and will no longer be indicated by the control panel. LOW BATTERY: Upon replacing the battery in a wireless device in a keyfob or in a wireless commander that reported a low battery, the next transmission made by the relevant sensor will include a “battery restored” message, and “low battery” will no longer be indicated by the control panel. SYSTEM TROUBLE: Correction of any one of the system troubles is automatically sensed by the control panel, and the trouble indication is cleared accordingly.
SPECIAL FUNCTIONS D-300886  17 6. Special Functions6. Special Functions6. Special Functions6. Special Functions     Looking after People Left at HomeLooking after People Left at HomeLooking after People Left at HomeLooking after People Left at Home    An important characteristic of the PowerMaxComplete  is its ability to function in a mode contrary to the usual behavior of an alarm system. When the system is in the disarmed state (or even when armed “HOME” with perimeter protection only), it can keep track of in-house activity and will report lack of motion in interior zones if there is no detection of motion within predetermined time limits. To use this characteristic, you must ask your installer to program a specific time limit beyond which lack of motion will be reported as a “not active” alert.  To make things clear, let us assume that an elderly, sick or handicapped person is left unattended in a protected site. This person, disabled or sick as he may be, will not stay entirely still for hours. It is only natural that even while being asleep he will turn over in his bed from time to time. He might also wander into the kitchen to eat or drink, or to the bathroom for other necessities. Upon doing so, the bedroom, bathroom and kitchen motion detectors will detect his movement.  If, for example, the “lack of motion” time limit is set by your installer to 6 hours, a virtual 6-hour clock will carry out a 6-hour “countdown”. If motion is detected within the 6-hour time frame, the countdown will restart from the beginning (the virtual 6-hour clock will be “reset”) and no alert message will be sent out. If no motion is detected within the 6-hour time frame in any interior zone, the control panel will send a “not-active” alert message to the central monitoring station or to private telephones designated by the installer.  IMPORTANT!  In addition, you may provide the person confined to interiors with a single-button transmitter for distress situations, see next paragraph. Emergency Calls for HelpEmergency Calls for HelpEmergency Calls for HelpEmergency Calls for Help    Suppose the disabled person discussed above has an accident such as falling in the bathtub without being able to get up. It might take hours before the “No Active” alert is sent out, but he (or she) must be assisted much sooner. Even though the odds for such an accident are not high, it is advisable to provide the disabled person with a miniature, single-button pendant-type or wristwatch-type transmitter. Pressing the button on this transmitter will cause the PowerMaxComplete  to send an “emergency call” to the central monitoring station or to private telephones designated by the installer. To make this possible, ask your installer to define one of the 28 zones of the PowerMaxComplete  as an emergency zone.  Then, obtain one of the transmitters listed below and link this transmitter’s ID code to the emergency zone.  Compatible distress transmitters are (see Fig. 5): MCT-201 - pendant-type MCT-211 - wristwatch-type MCT-101 - pocket-type MCT-201 MCT-211 MCT-101 Figure 5. Single-button Emergency Transmitters Remote Control by TelephoneRemote Control by TelephoneRemote Control by TelephoneRemote Control by Telephone    controlpanel A. Establishing Telephone Communication  You can access the PowerMaxComplete  system from a remote telephone and perform arming and disarming, activation and deactivation of electrical devices and the auxiliary output (PGM), record, playback and erase a voice message, and investigate the system status. The process is shown in the next illustration. 1.  Dial the PowerMaxComplete  tel. No.    2.  Wait for 2-4 rings then hang up. 3.  Wait 12-30 sec. 4. Redial PowerMaxComplete  tel. No. (Sound will be heard for 10 sec.).  Not applicable when dialing to the GSM number of the PowerMaxComplete. Proceed to step 5. 5.   [*} (to stop the sound) 1 6.   [user code], [#] 2  7.   [Desired command, see next table] 3 Notes (1) The PowerMaxComplete  responds in a similar way if you just dial once and wait until you hear telephone rings (in USA, for example, 11 rings). (2)  Entering of user code is required once only. (3) If you wait more that 50 seconds (may change according to setup / use) without keying a command, the PowerMaxComplete  will disconnect the line.
SPECIAL FUNCTIONS 18  D-300886 B. Executable Commands Command Keying Sequence Disarming  [$]%[1]%[#] Arming Home [$]%[2]%[#] Arming Home-Instant [$]%[2]%[1]%[#] Arming Away [$]%[3]%[#] Arming Away-Instant [$]%[3]%[1]%[#] Arming Away-Latchkey [$]%[4]%[#] Arming Away-Instant-Latchkey  [$]%[4]%[1]%[#] Activating PGM output  [$]%[5]%[0]% [0]%[1]%[#] Deactivating PGM output  [$]%[5]%[0]% [0]%[0]%[#] Two-way voice communication (see sub-par. C) [$]%[7]%[#] Recorded message playback   [$]%[8]%[1] %[#] Recorded message start record  [$]%[8]%[2] %[#] Recorded message stop record  [$]%[8]%[3] %[#] Recorded message erase message  [$]%[8]%[4] %[#] Investigating system status  [$]%[9]%[#]  Quit (end communication)  [$]%[9]%[9]%[#] C. Two-Way Voice Communication Perform steps 1-6 in Establishing Telephone Communication  above and continue as follows: 1.  [$$$$]%%%%[7]%%%%[#] 2.  Wait for 2 beeps 3.  [3] or [1] or [6] (see below) The system will start to function in the "LISTEN IN" mode, letting you hear the sounds within your residence for 50 seconds. If the person under surveillance happens to speak or cry then, you will hear this. You can switch the system to Listen-In, Speak Out or Full Duplex, as shown in the next table.  Command KeyListen-in (listening to the person at home) (*)  [3] Speak-out (speaking to the person at home) (*)  [1] Full-duplex (listening & speaking) (*)    [6] Note: To prolong the communication session by 50 seconds, press [3], [1] or [6] again, as required.  *  The 2-way communication can be terminated by anyone close to the PowerMaxComplete, by disarming the system. Remark Regarding Listen-in & Speak-out modes Listen-in & Speak-out modes allow one way speech at a time. Back and forth exchange of uninterrupted speech between two parties is a method normally used in military, commercial and amateur radio communication. Once you finish talking you should say “Go Ahead” or “Over” and then switch from speak-out to listen in. When the person at home finishes talking he should also say “Over”, as a cue to you to switch back from Listen-in to speak out. EXAMPLE: You (at remote telephone):   [1], “Hey, George, can you hear me? Are you in any trouble? Over”....  [3] Person at home: “Yes, I am. I had a dizzy spell while trying to get out of bed and fell on the floor. I am unable to get up and my thigh hurts. Can you help me? Over”... You (at remote telephone):   [1], “Sure, I will send someone right away, stay put - over”..  [3]. Person at home: “Thanks, please hurry, over”. You (at remote telephone):   [1], “All right, over and out”.....  [$]%9]%[9] (END OF SESSION) Important! If you wish to exit the two-way communication mode and execute another command, just press [$] and then key your user code followed by the command (see “keying sequences” in Executable Commands table above). Reporting to Private TelephoneReporting to Private TelephoneReporting to Private TelephoneReporting to Private Telephone    controlpanel The PowerMaxComplete  can be programmed by the installer for selective transmission of messages to private telephone subscribers. Messages are divided by type into 3 groups: Group Events Reported 1  Fire (*), Burglary (**), Panic, Tamper 2  Arming AWAY, Arming HOME, Disarming 3  No-activity, Emergency (***), Latchkey Note:  In control panel with no-voice option, the following siren signal will be sent to private telephone upon event reporting: *  FIRE: ON - ON - ON - pause.... (- - -  - - - ......). **   BURGLAR: ON continuously ( ...) ***  EMERGENCY: 2-tone siren; like an ambulance. Group 1 has the highest priority and group 3 has the lowest priority. When the called party answers a call initiated by the PowerMaxComplete, he will hear a verbal message composed of the “house identity” and the type of event that occurred. For example, once smoke is detected in the Smith residence, the message will be: [The Smith Residence - Fire Alarm].
SPECIAL FUNCTIONS D-300886  19 If a person under surveillance in the Watkins residence has been inactive, the message will be: [The Watkins Residence - No Activity]. The called party must acknowledge the message (as explained later on), but if he does not respond, the message will be transmitted repeatedly as many times as possible within a 45-second time limit. When the 45 seconds are up, the PowerMaxComplete  will disengage the line and call the next private telephone number on its list. The called party can acknowledge the message by pressing a key on the telephone keypad, as follows. Command Key Acknowledge only: The PowerMaxComplete  disengages the line and considers the event duly reported. 2 Acknowledge and listen-in: The protected site is “bugged” for sound for 50 seconds. The called party may prolong the listening session by pressing [3] again before the PowerMaxComplete  disengages the line, or by pressing [1] to speak. 3 Acknowledge and speak out: The called party may speak for 50 seconds to whoever is in the protected site. The called party may prolong the “speak out” session by pressing [1] again before the PowerMaxComplete  disengages the line, or by pressing [3] to listen. 1 Acknowledge and 2-way conversation: You and the called party can speak and listen without any necessity to switch the system from "listen-in" to "speak-out" and vice versa for 50 sec. (extendable). 6 Acknowledge and request a status report: The PowerMaxComplete  will issue a verbal report of system status. For example: [Disarm - ready to arm]  or [Disarm - back door open]  or [Disarm - alarm in memory]. 9  Remote ControlRemote ControlRemote ControlRemote Control by SMS by SMS by SMS by SMS    PowerMaxComplete system with an optional internal/external GSM unit can respond to SMS commands from any cellular GSM telephone, only if the “REM ACCESS ON” command was pre-selected by the system installer. The various SMS commands are detailed in the following table (the detailed SMS message sending process is described in the cellular telephone user’s guide). In this table, “<code>” means 4-digit user code and blank space simply means blank space.  SMS Command List  Command SMS Format 1  Arm AWAY  “AWAY <code>”  or  “AW <code>”  2  Arm AWAY instant  “AWAY INST <code>” or “AWI <code>”  3 Arm AWAY Latchkey  “LATCHKEY <code>”  or  “LK <code>”  4 Arm AWAY Latchkey instant  “LATCHKEY INST <code>”  or “LKI <code>”  5  Arm HOME  “HOME <code>” or “HM <code>”  6  Arm HOME instant  “HOME  INST  <code>”or “HMI <code>”  7  Disarm  “DISARM <code>” or “DA <code>”  8  Turn PGM on  “PGM ON <code>” 9  Turn PGM off  “PGM OFF <code>” 10 Define custom house identity (see note) “HOUSE NAME <code> <house ID>” or “HN <code> <house ID>” 11 Query system status  “STATUS <code>” or “ST <code>”  Note: House ID includes up to 16 characters, for example JOHN'S HOUSE. Reporting by SMSReporting by SMSReporting by SMSReporting by SMS    This option is applicable only if the GSM Module is installed. The PowerMaxComplete system can send SMS messages to a registered SMS telephones (up to 4). (The SMS telephone registration is preselected by the system installer). The reported SMS messages are quite clear and self-explanatory and therefore are not detailed in this guide.  Example of the reported SMS messages: •  JOHN’S HOME **AWAY** •  JOHN’S HOME **DISARM** •  JOHN’S HOUSE   POWERMAX: LOW BATTERY GARAGE: LOW BATTERY •  JOHN’S HOUSE   STATUS MESSAGE 01 (Event list is displayed) Note Status messages can be sent only to a calling telephone whose identity number is not blocked by the user!
SPECIAL FUNCTIONS 20  D-300886 Reporting Messages to a PagerReporting Messages to a PagerReporting Messages to a PagerReporting Messages to a Pager    MPagerControlpanel Since the PowerMaxComplete can be programmed to report events to a pager, the user of the pager must be informed on how to interpret the numerical message that his pager displays. Communication with a pager takes place as follows: •  The PowerMaxComplete dials the pager’s phone number, waits 5 seconds and sends the numerical message. •  The message transmitted by the PowerMaxComplete to the pager is actually a string of digits, as follows: [XXXXXXXXXXXXXXXX][YYY][0ZZ#]Pager’s PIN No. - Up to 16 digitsProgrammed by the Installer Zone orUser No.Event Type Figure 6. Pager Message Structure The person receiving the message sees only the “YYY -0ZZ#” part of the message, which he can interpret by using the following legend: Events types (YYY) are coded as follows: Event Code  Event Code Alarm 919  Fire 515 Trouble 818  Close 101 Emergency 717    Open  102 Panic 616  Latchkey 103 ZZ is the zone number in which the event occurred, or the user number in case of Close, Open and Latchkey events. Example 1: Message reads “919-003”: This means an alarm occurred in Zone No. 3. Example 2: Message reads “101-008”: This means the system was closed (armed) by user No. 8. Conducting a Walk TestConducting a Walk TestConducting a Walk TestConducting a Walk Test    The walk test is an indispensable operation by which you verify that all detectors function properly, without disturbing the neighbors with loud sirens. The test must be performed at least once a week, and should include all detectors in all zones.  Before performing walk test, all the detectors must be in normal state. Normal state is achieved when no motion is made for at least 2 minutes. Note: During the test period, 24-hour zones will not cause an alarm if violated, but a fire zone will function normally.  A typical test will take place as follows: A.  Press the test button  . B.  The display will prompt you for your user code: ENTER CODE    _ _ _ _ C. Enter your code. The siren will sound for 2 seconds and the display will change to: TESTING D. Walk throughout the protected area and make sure you trigger every detector with no exception (move across the field of view of motion detectors and open/close doors and windows). Each time a detector is triggered:  •  The “Happy Tune” will sound,  •  The zone name and number will be displayed briefly,  EXAMPLE 1: You triggered a motion detector in the living room (zone 11). The display will show: LIVING ROOM ! Z11 VIOLATED After 5 seconds the display will revert to: TESTING EXAMPLE 2: You opened a window in the guest room (zone 13). The display will show: GUEST ROOM ! Z13 OPEN After 5 seconds the display will revert to: TESTING E. When done, click the   button repeatedly. The display will show the test results, zone after zone, in ascending numerical order. For example: GUEST ROOM       (alternating)       Z13 OK or: “Z13   NOT OK” if there was no response from Z13. F.  To resume testing, click  . To quit the test mode, click  . The display will then read: <OK> TO EXIT G.  Click  . The display will revert to its normal state.
USER SETTINGS D-300886  21 7. User Settings7. User Settings7. User Settings7. User Settings    What are the Settings You Need?What are the Settings You Need?What are the Settings You Need?What are the Settings You Need?    The installer provides you a ready-to-use alarm system, but a few settings and adjustments will still be needed.  Note: Although the user settings are your responsibility, you may request your installer to perform them for you (except for the user codes, which you would like to keep secret). The user settings include: •  Bypassing zones - determining which zones will be bypassed (disabled) during the present disarm period and the next armed period.  •  Reviewing the bypass list - "show bypass" - displaying the numbers and names of bypassed zone one by one. •  Recalling the last bypassing scheme - "recall bypass" - re-using the previous bypassing scheme, which becomes suspended after disarming but is still saved in the PowerMaxComplete memory. •  Programming the 4 telephone numbers* - determining the 1st, 2nd, 3rd and 4th telephone numbers to which the system will report event messages that were defined by the system installer. •  Setting user codes* - programming a security code for yourself and additional 7 codes for other system users. Codes 5 through 8 are “Latchkey” user codes (see Chapter 2 - Arming in the Latchkey Mode for additional details). •  Enrolling keyfob transmitters* - teaching the PowerMaxComplete system to recognize the ID code of each keyfob transmitter (multi-button, Code-Secure™ type, wireless transmitter), so that the PowerMaxComplete can respond to commands transmitted by them. •  Enrolling proximity tags (optional) - Teaching the PowerMaxComplete to recognize the ID of each proximity tag so that the PowerMaxComplete can respond to proximity tags presentation. •  Setting voice options* (not applicable in PowerMaxComplete that does not have VOICE feature) - Enabling or disabling verbal announcements (prompts).  •  Auto arm option* - enabling or disabling automatic arming (at a predefined time). •  Setting auto arm time - selecting automatic arming time. •  Using squawk option* - enabling/disabling LOW/MID/HI squawk (short siren sound) upon arming and disarming. All the options are applicable for wireless siren. For wired siren, refer to LOW, MID and HI options as "squawk enable". •  Setting the time and time format* - adjusting the built-in clock to show the correct time and time format. •  Setting the date and date format* - adjusting the built-in calendar date and date format. •  Setting the scheduler*  -  setting schedule for devices start/stop activation. *  This option can be accessed only if master user code has been entered. Entering the User Settings MenuEntering the User Settings MenuEntering the User Settings MenuEntering the User Settings Menu    Figure 7 describes how to enter User Settings menu. 2Display in disarm state when allzones are secured (”00:00 orother digits show present time).1Instruction: click            keyResultant displayInstruction: Enter 4-digit masteruser code (default “1111”), oruser code (see note below).43ENTER CODE _ _ _ _&&&READY 00:00NORMAL MODEUSER SETTINGS[master/ user code]&SHOW BYPASSRECALL BYPASSSET PHONE NUMBER'SET USER CODES'''(*)(*)SET BYPASSThese menu items are displayedonly if “bypass” was enabled bythe installer.'ENROLL KEYFOB(*)'ENROLL PROX TAG(*)'AUTO ARM OPTIONAUTO ARM TIMESQUAWK OPTIONSET TIME&FORMATSET DATE&FORMATSET VOICE OPTION''''(*)(*)(*)(*)(*)'(*)'SET VOICE OPTION is Notaplicable in PowerMax LE thatdoes not have VOICE feature.*   Menu items that are markedwith an asterisk can beaccessed only if masteruser code has been entered.** INSTALLER MODE isdisplayed only if USERPERMIT ENABLE wasselected by the installer.Optional<OK> TO EXIT''(**)INSTALLER MODE(*)SCHEDULER(*) Figure 7 - Entering User Settings Menu The next paragraphs include User Settings instructions, step-by-step. However, if you want to get an overall view of the entire User Settings menu, refer to figure 8 - User Setting flow-chart. You can use the flow chart as your only guide along the user settings process, instead of going through the step-by-step instructions.
USER SETTINGS 22  D-300886 Bypassing ZonesBypassing ZonesBypassing ZonesBypassing Zones    A. General Guidance You can program the PowerMaxComplete to exclude (bypass) selected zones, regardless of whether these zones are "functional" (undisturbed) or "open" (disturbed). Bypassing permits free movement of people within certain zones although the system is armed. It is also used to temporarily remove from service faulty zones that require repair work. Fire zones can not be bypassed.  Remember – zone bypassing compromises security! Zone bypassing must be carried out while the system is in the disarmed state. Note:  Zones will be bypassed throughout one disarm-arm period only. Disarming the system after arming will suspend the entire bypassing scheme, which can be recalled later, if so desired. B. Bypassing Procedure Having entered your user code successfully (see above - Entering to the User Settings Menu), the display will read: SET BYPASS If at this point you click  , the number, state and name of the first zone will be automatically displayed. Three states are possible: •  Open:  The zone is not secured - you can bypass it if you do not wish or know how to solve the problem just now. •  Bypassed:  The zone is presently bypassed (you bypassed it before but haven't armed the system yet).   •  Functional: If there is nothing wrong with the zone, its state is described as "Functional".  Let us assume that Zone 1 is "open" and you wish to bypass it, and the rest of the zones are functional. PRESS RESULTANT DISPLAY Z01: OPEN        (alternating)             KITCHEN <OK> TO BYPASS  Z01: BYPASSED        (alternating)         KITCHEN Z02: FUNCTIONAL      (alternating)            FRONT DOOR  (If you wish to check the  state of the next zone)    SET BYPASS You can select any other item on the USER SETTINGS menu or quit programming by clicking  . When <OK> TO EXIT is displayed - click  . After end of bypassing operation, BYPASS blinks: READY BYPASS  or  NOT READY BYPASS This indication will persist as long as the system remains disarmed, and will disappear once the system is armed.  Note: BYPASS will alternate in the display with other messages, like: Trouble, Memory and Message. C. "Unbypass" Procedure Suppose you wish to restore a zone to service after having completed the bypassing scheme. Simply re-enter the SET BYPASS menu (see Bypassing Procedure above), and click   or   until the zone you wish to "unbypass" is on display. Refer to the following steps. PRESS RESULTANT DISPLAY Z22: BYPASSED        (alternating)         LIVING ROOM <OFF> TO CLEAR  Z22: FUNCTIONAL      (alternating)         LIVING ROOM You may now click   and then select any other item on the USER SETTINGS menu, or click   to quit programming. When <OK> TO EXIT appears - click  . Reviewing the Bypassed Zone ListReviewing the Bypassed Zone ListReviewing the Bypassed Zone ListReviewing the Bypassed Zone List    Having entered your user code successfully (see above - Entering to the User Settings Menu), the display will read:  SET BYPASS Click   to change the display into: SHOW BYPASS Click   to change the display into: BYPASS LIST If at this point you click  , the number, state and name of the first bypassed zone will be displayed.  You can now click   repeatedly to review all bypassed zones, in ascending numerical order. When done, clicking   will get you back to SHOW BYPASS and clicking   will get you back to <OK> TO EXIT.
USER SETTINGS D-300886  23  Recalling the Last Bypass SchemeRecalling the Last Bypass SchemeRecalling the Last Bypass SchemeRecalling the Last Bypass Scheme    Arming the alarm system with several zones in the bypassed state is in fact "partial arming". An identical partial arming may be repeated by recalling the last bypassing scheme (that was suspended and memorized upon disarming the system). Having entered your user code successfully (see above - Entering to the User Settings Menu), the display will read:  SET BYPASS Click   twice to change the display into: RECALL BYPASS At this point proceed as follows: ACTION RESULTANT DISPLAY <OK> TO RECALL  RECALL BYPASS  You may now select any other item on the USER SETTINGS menu or quit programming by clicking . When <OK> TO EXIT is displayed - click . Programming 4 Telephone NumbersProgramming 4 Telephone NumbersProgramming 4 Telephone NumbersProgramming 4 Telephone Numbers    Here you determine the 1st, 2nd, 3rd and 4th telephone numbers to which the system will report event messages that were defined by the system installer. You can ask the installer to set part or all the four telephone numbers. Having entered your Master User Code successfully (see above - Entering the User Settings Menu), click  button repeatedly (if necessary) until the display will read: SET PHONE NUMBER You are allowed to program the 4 numbers as follows:  PRESS RESULTANT DISPLAY 1st private tel#  XXXXXXXXX  [Enter Tel. No.]  XXXXXXXXX   XXXXXXXXX   1st private tel#  2nd private tel#    Continue the same way up to telephone number 4. You may now switch to any other item on the USER SETTINGS menu or quit programming by clicking  until <OK> TO EXIT is displayed and then clicking  . Setting the User CodesSetting the User CodesSetting the User CodesSetting the User Codes    A maximum of eight 4-digit codes can be defined out of a total of (10)4 = 10000 user code possibilities. Having entered your Master User Code successfully (see above - Entering the User Settings Menu), click  until the display reads: SET USER CODES User Code 1 replaces the factory default master user code, and should be assigned to the master user of the system. This code can not be erased.  User Codes 2, 3 and 4 can be assigned to additional users - family members, co-workers etc.  Codes 5 through 8 are assigned to “Latchkey Users” (see Chapter 2 - Arming in the Latchkey Mode, for an explanation of the latchkey mode). CAUTION! Code “0000” is not valid! Do not use it. Note: The duress code set by the installer (2580 by default) cannot be selected as a normal user code. Any attempt to program it will be rejected by the PowerMaxComplete. To program the codes, proceed as follows: PRESS RESULTANT DISPLAY user code 1: _ _ _ _  user code1: 0 0 0 0  user code 1: 6854  [4-digit user code] e.g. 6854) user code 1: 6854   user code 2 Continue the same way up to Code 8. user code 8: 5537  SET USER CODES  You may now select any other item on the USER SETTINGS menu or quit programming by clicking . When <OK> TO EXIT is displayed - click .
USER SETTINGS 24  D-300886 RECALL BYPASS(5)SET PHONE NUMBER(1)SET USER CODES(1)AUTO ARM OPTIONAUTO ARM TIME(1)(1)SET VOICE OPTION(1)(6)ENROLL KEYFOB(1)'''''''ENROLL PROX TAG(1)'SHOW BYPASSSET BYPASSREADY 00:00(5)(5)''SQUAWK OPTIONSET TIME&FORMAT US FORMAT - 12H EU FORMAT - 24HTIME _ _:_ _A TIME _ _:_ _'[time] e.g. 07:55P '[time] e.g. 19:55DATE DD/MM/YYYY DATE MM/DD/YYYYSET DATE&FORMAT(1)(1)(1)(4)if not satisfied'if not satisfied''''''''''TIME 07:55 P TIME 19:55''squawk disablesqwk low volumesqwk mid volumesqwk hi volume(To review options, use             or            button)'Moving forwardMoving backwardMoving one levelup in the menuReturn to“<OK> TO EXIT”To move within most ofthe menus, the followingkeys can be used:Show / confirmdataDATE: _  _/_ _/_ _ _ _DATE:_ _/_ _/_ _ _ _'(date)(2)'(date)(2)''DATE 30/12/2000 DATE 12/30/2000''(e.g. 30/12/2000) (e.g. 12/30/2000)<OK> TO EXIT'(see detail “A”in next page)SCHEDULER''INSTALLER MODE(1)(1)<OK> TO RECALLuser code 1 0 0 0 0(for next user code 2,3....8)[code]user code 1 user code1(example)disable autoarm enable autoarm(if it is the current option)'[time]arm time _ _: _ _A(See format & example in“SET TIME&FORMAT” )enable prompts(if it is the current option)Keyfob No : TRANSMIT NOW KEYFOB No : 1''disable prompts disable promptsenable autoarmenter keyfob #for next (up) or previous (down)  keyfob enrollment''''(press any key)''''1st private tel# 2nd private tel# 3rd private tel# 4th private tel#PRESENT TAG(for next prox tags 2,3....8)Tag no   : 1(example)'Tag no   :   1BYPASS LIST(3)NORMAL MODE<OK> TO BYPASS Z01: BYPASSEDZ01: OPENKITCHENAlternatingKITCHENAlternating(for checking stateof next zone)ENTER CODE  _ _ _ _INSTALLER MODE(example)[4-digit master/user code]USER SETTINGS''&&Tel. No.&&&Tel. No.&&&Tel. No.&&&Tel. No.&if notsatisfiedif notsatisfied(First display isREADY / NOT READY)Entrance to INSTALLERMODE (described inthe installer guide)Optional Notes:  (1) Function inside black rectangles are accessible only if master user code was entered. (2) For the year, enter the two last digits only. (3) Press  to display the number, state and name of first bypassed zone. Press   repeatedly to view all the bypassed zones. (4) To enter "A" (AM) press   (or one of the 3 keys above it), to enter "P" (PM) press   (or one of the 3 keys above it). (5) SET/SHOW/RECALL BYPASS menus are accessible only if "manual bypass has been selected by the installer. (6)Applicable in PowerMaxComplete that has VOICE feature -  In the SET VOICE OPTION, if you select "enable prompts", the Control Panel mute speaker button   is active. Figure 8 - Users Settings Flow Chart
USER SETTINGS D-300886  25 'Moving forwardMoving backwardMoving one levelup in the menuReturn to“<OK> TO EXIT”To move within most ofthe menus, the followingkeys can be used:Show / confirmdata' ' ' ' ' ''SET TIME&FORMAT'SCHEDULER'PGM(See figure 8)SUNDAY MONDAY TUESDAY WEDNESDAY FRIDAY SATURDAY DAILY''''start -  HH:MMstop -  HH:MMorTIME - - / - -(enter start/stop time)'Notes1. Select time in 10 minute interval only.2. To erase a displayed time, press OFF.''OPERATION No. 1 OPERATION No. 2 OPERATION No. 3 OPERATION No. 4THURSDAY' Figure 8 DETAIL "A" - Scheduler Function Enrolling Keyfob TransmittersEnrolling Keyfob TransmittersEnrolling Keyfob TransmittersEnrolling Keyfob Transmitters    Keyfob transmitters are multi-button wireless units of the CodeSecure™ type with up to 16 million ID codes combinations. Eight system users carry keyfob transmitters to exercise better, quicker and safer system functions control. Your control panel must recognize the unique identification code (ID) of each such keyfob to respond to commands transmitted by them. Before anything else, gather up all keyfob units you intend to enroll, and make sure they all have batteries installed. Keyfob transmitter enrolling involves the following steps: A. Having entered your Master User Code successfully (see above - Entering the User Settings Menu), Click the   button (repeatedly, if necessary) until the display will read:  ENROLL KEYFOB B. Click  . The display will read: KEYFOB No:         _ C.  Suppose that the Keyfob you are about to enroll is to be designated as Keyfob No. 5. Assuming that memory location No. 5 is free - no keyfob has yet been enrolled to it - click the <5> key. The display will change to: KEYFOB No:    5  The clear space at the far right tells you that the memory location is free. D.  Click  . The display will prompt you to initiate a transmission from the chosen keyfob: TRANSMIT NOW E.  Initiate a transmission from the chosen keyfob by pressing any one of its pushbuttons. In response, the “Happy Tune” (- - - –––) will sound and the display will change to: KEYFOB No:      5            A dark box will appear at the far right, indicating that the chosen Keyfob has been enrolled as Keyfob  No. 5. Note: If the same keyfob is already enrolled elsewhere, the “Happy Tune” will sound twice in succession. F.  From this point on, you may continue in several different directions: •  If you wish to enroll another keyfob, select the desired number by:   - - Clicking   to go up (6%7%8.....)   - Clicking   to go down (4%3%2.....)     - Clicking   % <keyfob #>. •  To return to the main menu, click  . This will bring back the display: <OK> TO EXIT
USER SETTINGS 26  D-300886 You may now review and select any other mode on the User menu (by clicking   or  ). Deleting KeyfobDeleting KeyfobDeleting KeyfobDeleting Keyfob    Occupied keyfob memory locations must be cleared (enrolled ID must be deleted) before enrolling a new ID. To delete an existing ID, proceed as follows: A.  Select the desired memory location, as described in the previous paragraph, steps A-C. If, for example, you selected keyfob No. 5, the display will read: Keyfob No.                  5   B.  Click  . The display will change to: <OFF> to delete C.  Click  . The display will change to: Keyfob No.                      5    Note that the dark box at the far right has disappeared. It is now possible to enroll a new ID. It is also possible to leave the cleared zone or memory location free and simply exit to the main menu. Enrolling Proximity Tags (optional)Enrolling Proximity Tags (optional)Enrolling Proximity Tags (optional)Enrolling Proximity Tags (optional)    Valid proximity tags enable you to perform variety of functions without entering user code, for example, arming, disarming, reading the event log, etc. Whenever user code is required, you can simply present a valid proximity tag instead of entering user code.  When the system is disarmed, after presenting a valid proximity tag to the control panel, the message "<OK> for AWAY" is displayed. Now you can press the   button to immediately arm the control panel, or wait for 3 second for system automatic AWAY arming (the message "Please exit now" will be displayed). Presenting the proximity tag once again will DISARM the system. Instead of pressing the   button (see above), you can press the  button once / twice (the message "<OK> for HOME" / "<OK> for disarm" is displayed, accordingly) and then press the press   button for HOME arming / disarming.   The control panel transmits an RF signal. A valid proximity tag that is presented to the control panel transmits a coded RF signal back to the control unit.  Up to 8 proximity tags can be enrolled to the PM PRO.Proximity tag enrolling involves the following steps: A. Having entered your Master User Code successfully (see Entering the User Settings Menu), Click the   button (repeatedly, if necessary) until the display will read:   ENROLL PROX TAG B. Click  . The display will read:  Tag No:   1 C.  Click  . The display will prompt you to initiate a transmission from the chosen tag:  PRESENT TAG D. Present the tag to the control panel left bottom side. In response, the “Happy Tune” (- - - –––) will sound and the display will change to:  Tag No:   1    A dark box will appear at the far right, indicating that the chosen tag has been enrolled. E. Click   and enroll the next proximity tag (2, 3,...8), as described in step D. F.  From this point on, you may continue in several different directions: •  If you wish to enroll another tag, select the desired number by:   - Clicking      to go up  (6%7%8.....)   - Clicking  to go down (4%3%2.....)     -   Clicking     % <tag#>. •  To return to the main menu, click   . This will bring back the display:  <OK> TO EXIT You may now review and select any other mode on the User menu (by clicking   or  ). Deleting Proximity TagsDeleting Proximity TagsDeleting Proximity TagsDeleting Proximity Tags    Proximity tag memory locations must be cleared (enrolled ID must be deleted) before enrolling a new ID. To delete an existing ID, proceed as follows: A.  Select the desired memory location, as described in the previous paragraph, steps A-C. If, for example, you selected Tag No. 5, the display will read: Tag No.   5   B.  Click  . The display will change to: <OFF> TO DELETE   C.  Click  . The display will change to: Tag No.   5
USER SETTINGS D-300886  27 Note that the dark box at the far right has disappeared. It is now possible to enroll a new ID. It is also possible to leave the cleared zone or memory location free and simply exit to the main menu. Setting the VoSetting the VoSetting the VoSetting the Voice Optionsice Optionsice Optionsice Options    (Not applicable in PowerMaxComplete that does not have VOICE option)  Remember: Voice prompts are heard over the built-in loudspeaker subject to two conditions:  -   The voice option is enabled as shown below -  The loudspeaker is enabled by pressing the “7” key (see Chapter 3 - Voice ON-OFF) Here you may select one of two options:  Enable prompts: Voice announcements Disable prompts: No voice announcements The presently programmed option will be shown, with a dark selection box ( ) at the far right of the display. You may view the other option (that does not have a dark box at the far right) by clicking . A dark box will appear if you click  while the other option is displayed. To set the voice option, proceed as follows: Having entered your Master User Code successfully (see above - Entering the User Settings Menu), click the   button until the display reads: SET VOICE OPTIONS From here, proceed as follows: PRESS RESULTANT DISPLAY enable prompts               (if this is the current option)  disable prompts If not satisfied      disable prompts            If satisfied - SET VOICE OPTION  You may now select any other item on the USER SETTINGS menu or quit programming by clicking . When <OK> TO EXIT is displayed - click . Note: When using the Model MCT-234 keyfob with the PowerMaxComplete, the voice prompts must be enabled. Automatic Arming OptionAutomatic Arming OptionAutomatic Arming OptionAutomatic Arming Option    You can determine that the system will be automatically armed at any desired time. Having entered master user code successfully, click  until AUTO ARM OPTION is displayed. From here, proceed as follows: PRESS RESULTANT DISPLAY enable autoarm               (if this is the current option)  disable autoarm If not satisfied press   disable autoarm               AUTO ARM OPTION  You may now select any other item on USERS SETTINGS menu or quit programming process by clicking  . When "<OK> TO EXIT" is displayed, click  . Setting Arming TimeSetting Arming TimeSetting Arming TimeSetting Arming Time    Having entered your Master User Code successfully (see above - Entering the User Settings Menu), click  button (repeatedly, if necessary) until the display will read: AUTO ARM TIME From here, proceed as follows: PRESS RESULTANT DISPLAY arm time_ _ : _ _ A   arm time 12:55 A  [time digits] (e.g. 12:55 A)  arm time 12:55 A          AUTO ARM TIME  Notes: 1.  For 12h/24h time format selection, refer to  Setting Time and Time Format  below. 2. Press "(" to enter A (AM), or press "#" to enter P (PM). Enabling the Squawk OptionEnabling the Squawk OptionEnabling the Squawk OptionEnabling the Squawk Option    You can determine that the system will activate (or not activate) high/mid/low siren sound, for a short time, upon arming (1 beep) and disarming (2 beeps), by keyfob only. Having entered your Master User Code successfully (see above - Entering the User Settings Menu), click the   button (repeatedly, if necessary) until the display will read: SQUAWK OPTION
USER SETTINGS 28  D-300886 From here, proceed as follows: PRESS RESULTANT DISPLAY squawk disable              (if this is the current option)  squawk low volume If not satisfied -    squawk mid volume If not satisfied -    squawk hi volume If not satisfied    squawk hi volume         If satisfied    For wired siren, refer to "low", "mid" and "hi" options as "squawk enable". You may now select any other item on the USERS SETTINGS menu or quit the programming process by clicking  . When "<OK> TO EXIT" is displayed, click  . Setting Time and Time FormatSetting Time and Time FormatSetting Time and Time FormatSetting Time and Time Format    Having entered your Master User Code successfully (see Entering the User Settings Menu, above), click  until the display reads: SET TIME&FORMAT A. If 12h format is desired, continue as follows: PRESS RESULTANT DISPLAY US FORMAT  -  12H   (if this is the current option) TIME    _ _ : _ _ A    TIME    12:55A  (time digits] (e.g. 12:55A)   TIME      HH:MM  A  Note: To enter “A” - press [(] or to enter “P” - press [#].  B. If 24h format is desired, continue as follows: PRESS RESULTANT DISPLAY US FORMAT  -  12H   EU FORMAT  -  24H  TIME            _ _ : _ _  TIME    19:55   [time digits] (e.g. 19:55)   TIME     19:55   TIME     HH:MM   You may now select any other item on the USER SETTINGS menu or quit programming by clicking . When <OK> TO EXIT is displayed - click . Setting tSetting tSetting tSetting the Date and Date Formathe Date and Date Formathe Date and Date Formathe Date and Date Format    Having entered your Master User Code successfully (see above - Entering the User Settings Menu),  click  button (repeatedly, if necessary) until the display will read SET DATE&FORMAT.  From here, proceed as follows: PRESS RESULTANT DISPLAY DATE MM/DD/YYYY    DATE DD/MM/YYYY If not satisfied press   DATE  _ _ / _ _ /_ _ _ _    DATE 01/01/2002  [Enter date] (e.g. 01/01/2002)   DATE 01/01/2002    DATE DD/MM/YYYY   You may now select any other item on the USER SETTINGS menu or quit programming by clicking . When <OK> TO EXIT is displayed - click .
USER SETTINGS D-300886  29 Scheduler FunctionScheduler FunctionScheduler FunctionScheduler Function    The Scheduler enables to start and stop activity of the desired devices. You can select the day (Sunday, Monday, Tuesday, Wednesday, Thursday, Friday, Saturday, or daily) and then select the scheduled activity start/stop of the desired device. The process is demonstrated in "figure 8 DETAIL A". Installer ModeInstaller ModeInstaller ModeInstaller Mode    If the feature USER PERMIT was enabled by the system installer, the installer will be able to access the INSTALLER MODE only by using this menu, meaning that the INSTALLER MODE (described in the installer guide) can be accessed only with user permission (by using the user code).
READING THE EVENT LOG 30  D-300886 8. Reading The Event Log8. Reading The Event Log8. Reading The Event Log8. Reading The Event Log    Event Log DescriptionEvent Log DescriptionEvent Log DescriptionEvent Log Description    All events are memorized in an event log. You can access this log, review the events one by one and draw functional conclusions.  If the event log fills up completely it continues to accept new events at the expense of old events - the oldest event is deleted upon registration of each new event.  The date and time of occurrence are memorized for each event. When reading the event log, events are shown in chronological order - from the newest to the oldest. Because of the limited display space, the event description is shown first, then the date and time. The two displays are shown alternately several times, until you click   to move on to an older event, or until the “no action” 4-minute timeout restores the system to the normal operating mode.   Access to the event log is provided by clicking the asterisk ($$$$) key and then keying your master user code.  Should you wish to get an overall view of using the log, refer to Figure 9. The flow chart may even serve as your only guide to using the event log, instead of going through the written step-by-step procedure. Attention: The systemwill not allow you toerase the event log.Only the installer isauthorized to view andperform this function&Oldest EventEvent Before LastLatest EventLIST OF EVENTS&&ENTER CODE _ _ _ _(Enter 4-digitmaster user code)<OK TO EXITCLEAR EVENT LOG&&&&(Return to normaloperation)&& Figure 9. Using the Event Log Reading ProcedureReading ProcedureReading ProcedureReading Procedure    To read the event log, proceed as follows: A. While the system is in the normal operating mode, click the asterisk ($$$$) key. The display will change to: ENTER CODE _ _ _ _ B.  Enter the current master user code. If the code is correct, the “Happy Tune“ will sound and the display will read: LIST OF EVENTS Important! Entering an incorrect code 5 times in a row will initiate a 30-second penalty lockout of the keypad. C. Click  . The latest event will be shown. Suppose that the latest event was an alarm in zone 13. The display will now read: Z13 ALARM and then: 09 / 02/ 99                3:37 P    The two displays will be shown alternately until you click   again to move to the next event, or until the event log times out (4 minutes). D. Click   as many times as necessary to read all the data you need.  To quit the event log: - Click   or   from any-where within the log. The display will read: <OK> TO EXIT  - Click  . The system will return to the normal operating mode.
MAINTENANCE D-300886  31 9. Maintenance9. Maintenance9. Maintenance9. Maintenance Replacing the Backup BatteryReplacing the Backup BatteryReplacing the Backup BatteryReplacing the Backup Battery    The PowerMaxComplete uses regular electrical supply, but incorporates backup 9.6V battery pack (see sticker on battery cover). It is important to replace it immediately upon receiving the following trouble message when reviewing system troubles (see Chapter 5 - Reviewing Trouble Information): CPU LOW BATTERY Front unitBattery cable Figure 10. Battery Replacement Open battery compartment cover. Insert 6-battery pack or 8-battery pack and connect its connector to the PowerMaxComplete receptacle. Note: Removal of the cover will start a “tamper” alarm - the trouble indicator will light and both “memory” and “trouble” will flash in the display window. If you interrogate the system at this stage by clicking the  button, “CPU TAMPER ALARM” and “CPU TAMPER OPEN” will be displayed, in addition to “CPU LOW BATTERY”. With correctly inserted fresh batteries and tight closure of the lid, the TROUBLE indicator should extinguish. The “MEMORY” message will continue blinking in the display (caused by the “tamper” alarm you triggered). Clear it by arming the system and disarming it as soon as the exit delay starts. Replacing Wireless Devices Replacing Wireless Devices Replacing Wireless Devices Replacing Wireless Devices BatteriesBatteriesBatteriesBatteries    The wireless sensors supplied with your system are powered by high-capacity lithium batteries that last several years, depending on the number of times the sensor is triggered into transmission. However, if and when a battery becomes weak, the sensor itself sends a “low battery” message to the control panel, and a low battery trouble message is displayed together with the zone information (see Chapter 5 - Reviewing Trouble Information). The keyfob transmitters used to control the system are powered by an alkaline battery that lasts about one year if you do not press a button more than 10 times a day. Battery exhaustion is clearly evident by flashing of the transmitter’s red indicator while the button is pressed (instead of lighting steadily).  When a low battery indication appears for the first time, it may be considered as a pre-warning. It normally gives you ample time (about 30 days) to obtain a new battery and replace the old one, and the detector or keyfob unit will be fully operational throughout this period. However, to be on the safe side, it is advisable not to wait that long.  Use the battery specified in the detector’s own installation instructions. If you do not have the instructions, seek the advice of your installer or ask him to replace the battery in the specific device that sent the low battery message. The Wireless Commander is powered by a long life 3 V Lithium battery. If the battery is weak when reading the PowerMaxComplete event log the display will read, for example, "C01 Low Battery" (meaning there is a low battery condition in the wireless commander #01), and the message "remote commander" will be heard. For replacing the wireless commander battery, refer to the MCM-140+ Wireless Commander user guide. After battery replacement, the detector unit will send a “battery restored” signal to the control panel, and the “low battery” message will be cleared.
MAINTENANCE 32  D-300886 Periodic TestingPeriodic TestingPeriodic TestingPeriodic Testing    The components of your security system are designed to be maintenance-free as much as possible. Nevertheless, it is mandatory to perform a “walk test” at least once a week and after an alarm event to verify that all system detectors function properly. Proceed as described in Chapter 6 - Conducting a Walk-Test, and If there is any problem, notify your installer at once. Cleaning the Control PanelCleaning the Control PanelCleaning the Control PanelCleaning the Control Panel    The control panel may occasionally get stained if touched with greasy fingers, and may accumulate dust after a long period of use. Clean it only with a soft cloth or sponge moistened lightly with a mixture of water and mild detergent, and then wipe it dry. The use of abrasives of any kind is strictly forbidden. Also never use solvents such as kerosene, acetone or thinner. These will certainly ruin the external finish and damage the transparency of the top window.
PERFORMANCE LIMITS D-300886  33 10. Performance Limits10. Performance Limits10. Performance Limits10. Performance Limits    Although the alarm control system you purchased is highly reliable, it does not guarantee protection from burglary and fire hazards. Even the most advanced systems can be defeated or might occasionally fail to warn. Some of the reasons for this are: Sloppy maintenance: If the system is used over a long period of time without testing, a key element such as a detector or a siren might go wrong without any visible or audible signs of failure. If a low battery warning is neglected, there will be no backup power to keep the system operational during a power outage. Power failures: In case of prolonged absence from the protected site, the mains supply may suddenly fail (an earth leakage protection relay may trip, disconnecting the mains supply). After such an event, the alarm system will draw power from the backup battery, until all reserve power is exhausted, leaving the premises without protection. Telephone line trouble: Telephone lines may be disconnected or short circuited. With the telephone line "down", your alarm system will not be able to report events to the central station. Sirens do not always wake up sound sleepers: Sirens and bells installed outside or far from bedrooms are not likely to awaken people who are sound asleep behind closed doors inside the protected area or in adjacent buildings. The system is sometimes defeated: With sufficient technical know-how, intruders may find a way to defeat various types of sensor or disconnect warning devices. Intruders may also take advantage of unprotected openings and skylights, or even enter forcibly at unpredictable spots. Smoke detectors have their limits: In many cases, smoke detectors fail to warn on time because the fire started at a different level of the house, or too far away from the detector.  All this gives sufficient proof that even with a good alarm system installed, there is still need for life and property insurance. In addition, users should test their alarm systems at regular intervals, to make sure that malfunctions are detected before a true alarm event occurs.
APPENDICES 34  D-300886 APPENDIX A. GLOSSAAPPENDIX A. GLOSSAAPPENDIX A. GLOSSAAPPENDIX A. GLOSSARYRYRYRY    This list of terms is arranged in alphabetical order. Any term indicated by cursive (italic) letters within the explanatory text can be looked up separately. Abort Period: When an alarm is initiated, the internal sounder is activated first for a limited period of time which is the abort period set by the installer. If you cause an alarm accidentally, you can disarm the system within the abort period before the real sirens start and before the alarm is reported to the remote responders. Alarm: There are 2 kinds of alarm: Loud alarm - both internal and external sirens blare out constantly and the control panel reports the event by telephone. Silent alarm - the sirens remain silent, but the control panel reports the event by telephone. A state of alarm is caused by: •  Motion detected by a motion detector  •  Change of state detected by a magnetic contact detector - a closed window or door is opened •  Detection of smoke by a smoke detector •  Tampering with any one of the detectors •  Pressing the two emergency buttons simultaneously (panic) Arming: Arming the alarm system is an action that prepares it to sound an alarm if a zone is “violated” by motion or by opening a door or window, as the case may be. The control panel may be armed in various modes (see AWAY,  HOME, INSTANT and LATCHKEY). AWAY: This type of arming is used when the protected site is vacated entirely. All zones, interior and perimeter alike, are protected.  Chime Zones: Allow you to keep track of activity in the protected area while the alarm system is in the disarmed state. Whenever a chime zone is "opened", the buzzer beeps twice. The buzzer doesn't beep, however, upon closing the zone (return to normal). Residences can use this feature to annunciate visitors or look after children. Businesses can use it to signal when customers enter the premises or when personnel enter restricted areas.  Note:  Your installer will never designate a 24-hour zone or a fire zone as a chime zone, because both zone types actuate an alarm if disturbed while the system is in the disarmed state. Although one zone or more are designated as chime zones, you can still enable or disable the chime function. Control Panel: The control panel is a cabinet that incorporates the electronic circuitry and microprocessor that control the alarm system. It collects information from various sensors, processes it and responds in various ways. It also includes the user-interface - control keys, numerical keypad, display, sounder and loudspeaker. Disarming: The opposite of arming - an action that restores the control panel to the normal standby state. In this state, only fire and 24-hour zones will sound an alarm if violated, but a “panic alarm” may also be initiated. Disturbed Zone: A zone in a state of alarm (this may be caused by an open window or door or by motion in the field of view of a motion detector). A disturbed zone is considered “not secured”. Forced Arming: When any one of the system zones is  disturbed (open), the alarm system cannot be armed. One way to solve this problem is to find and eliminate the cause for zone disturbance (closing doors and windows). Another way to deal with this is to impose forced arming - automatic de-activation of zones that are still disturbed upon termination of the exit delay. Bypassed zones will not be protected throughout the arming period. Even if restored to normal (closed), bypassed zones will remain unprotected until the system is disarmed.  Permission to “force arm” is given or denied by the installer while programming the system. HOME: This type of arming is used when people are present within the protected site. A classic example is night-time at home, when the family is about to retire to bed. With HOME arming, perimeter zones are protected but interior zones are not. Consequently, motion within interior zones will be ignored by the control panel, but disturbance of a perimeter zone will cause an alarm. Instant: You can arm the system AWAY-INSTANT or HOME-INSTANT, thereby canceling the entry delay for all delay zones for the duration of one arming period.  For example, you may arm the control panel in the HOME-INSTANT mode and remain within the protected area. Only perimeter protection is active, and if you do not expect somebody to drop in while the system is armed, alarm upon entry via the main door is an advantage.  To disarm the system without causing an alarm, use your control keypad (which is normally accessible without disturbing a perimeter zone) or use a keyfob transmitter.
APPENDICES D-300886  35 Latchkey:  The Latchkey mode is a special arming mode in which designated "latchkey users" will trigger a "latchkey message" to be sent to a telephone or a pager when they disarm the system. For example, if a parent wants to be sure that their child has returned from school and disarmed the system. Latchkey arming is only possible when the system is armed in the AWAY mode. Magnetic Contact Detector, Wireless: A Magnet- controlled switch and a wireless PowerCode transmitter in a shared housing. The detector is mounted on doors and windows to detect changes in state (from closed to open and vice versa). Upon sensing that a door or window is open, the detector transmits its unique identification code accompanied by an “alarm” signal and various other status signals to the control panel. The control panel, if not armed at that time, will consider the alarm system as “not ready for arming” until it receives a “restored” signal from the same detector. Motion Detector, Wireless: A passive Infrared motion sensor and a wireless PowerCode transmitter in a shared housing. Upon sensing motion, the detector transmits its unique identification code, accompanied by an alarm signal and various other status signals to the control panel. After transmission, it stands by to sense further motion.  Non-Alarm Zone:  Your installer can designate a zone for roles other than alarm. For instance, a motion detector installed in a dark stairway may be used to switch on lights automatically when someone crosses the dark area. Another example is a miniature wireless transmitter linked to a zone that controls a gate opening mechanism. Quick Arming: Arming without a user code. The control panel does not request your user code when you press one of the arming buttons. Permission to use this arming method is given or denied by the installer while programming the system. Remote Responder: A responder can be either a professional service provider to which the home or business owner subscribes (a central monitoring station) or a family relation/friend who agrees to look after the protected site during absence of its occupants. The control panel reports events by telephone to both kinds of responders. Restore:  When a detector reverts from the state of alarm to the normal standby state, it is said to have been “restored”.  A  motion detector restores automatically after detection of movement, and becomes ready to detect again. This kind of “restore” is not reported to the remote responders. A  magnetic contact detector restores only upon closure of the protected door or window. This kind of “restore” is reported to the remote responders. Smoke Detector, Wireless: A regular smoke detector and a wireless PowerCode transmitter in a shared housing. Upon detection of smoke, the detector transmits its unique identification code accompanied by an alarm signal and various status signals to the control panel. Since the smoke detector is linked to a special fire zone, a fire alarm is initiated. User Codes: The PowerMaxComplete is designed to obey your commands, provided that they are preceded by a valid security access code. Unauthorized people do not know this code, so any attempt on their part to disarm or defeat the system is bound to fail. Some operations, however, can be carried out without a user code as they do not degrade the security level of the alarm system.  Zone:  A zone is an area within the protected site under supervision of a specific detector. During programming, the installer allows the control panel to learn the detector’s identity code and links it to the desired zone. Since the zone is distinguished by number and name, the control panel can report the zone status to the user and register in its memory all the events reported by the zone detector. Instant and delay zones are “on watch” only when the control panel is armed, and other (24-hour) zones are “on watch” regardless of whether the system is armed or not.
APPENDICES 36  D-300886 APPENDIX B. HOME FIRE ESCAPE PLANNINGAPPENDIX B. HOME FIRE ESCAPE PLANNINGAPPENDIX B. HOME FIRE ESCAPE PLANNINGAPPENDIX B. HOME FIRE ESCAPE PLANNING    Fire can spread rapidly through your home, leaving you a short time to escape safely. Your ability to get out depends on advance warning from smoke detectors and advance planning - a home fire escape plan that everyone in your family is familiar with and has practiced. Pull together everyone in your household and make an evacuation plan. Draw a floor plan of your home, showing two ways out of each room, including windows. Don’t forget to mark the location of every smoke detector. Test all smoke detectors (by a qualified testing laboratory) periodically, to ensure to ensure their serviceability. Replace batteries as required. Make sure that everyone understands the escape plan and recognizes the sound of smoke alarm. Verify that the escape routes are clear and that doors and windows can be opened easily. If windows or doors in your home have security bars, make sure that the bars have quick-release mechanisms on the inside, so that they can be opened immediately in an emergency case. Quick release mechanisms won’t compromise your security, but they will increase your chances of safely escaping a home fire. Practice the escape plan at least twice a year, making sure that everybody is involved - from kids to grandparents. Allow children to master fire escape planning and practice before holding a fire drill at night when they are sleeping. The objective is to practice, not to frighten, so telling children there will be a drill before they go to bed can be as effective as a surprise drill. If children or others do not readily waken to the sound of the smoke alarm, or if there are infants or family members with mobility limitations, make sure that someone is assigned to assist them in fire drill and in the event of an emergency. Agree on an outside meeting place where everyone can meet after they’ve escaped. Remember to get out first, and then call for help. Never go back inside until the fire department gives the OK. •  Have everyone memorize the emergency phone number of the fire department. That way any member of the household can call from a cellular phone or a neighbor’s home. •  Be fully prepared for a real fire: when a smoke alarm sounds, get out immediately and once you are out, stay bout - leave the firefighting to the professional! •  If you live in an apartment building, make sure that you are familiar wit the building evacuation plan. In case of a fire, use the stairs, never the elevator. Tell guests or visitors to your home about your family’s fire escape plan. When visiting other people’s home, ask about their escape plan. If they don’t have a plan in place, offer to help them make one. This is especially important when children are permitted to attend “sleepovers” at friends' homes. FCC STATEMENTFCC STATEMENTFCC STATEMENTFCC STATEMENT    The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received, including interference that may cause undesired operation. The digital circuit of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures: –  Re-orient or re-locate the receiving antenna. – Increase the distance between the device and the receiver. – Connect the device to an outlet on a circuit different from the one which supplies power to the receiver. – Consult the dealer or an experienced radio/TV technician.  The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be re-located or operating in conjunction with any other antenna or transmitter. Warning: Changes or modifications to this equipment not expressly approved by Visonic Inc. could void the user's authority to operate the equipment. W.E.E.E. Product Recycling Declaration For  information regarding the recycling  of this product  you must contact the  company from which you orignially purchased it. If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste. Directive 2002/96/EC Waste Electrical and Electronic Equipment.   VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788 VISONIC INC. (U.S.A.):  65 WEST DUDLEY TOWN ROAD, BLOOMFIELD CT. 06002-1376. PHONE: (860) 243-0833, (800) 223-0020 FAX: (860) 242-8094 VISONIC LTD. (UK):   FRASER ROAD, PRIORY BUSINESS PARK, BEDFORD MK44 3WH. PHONE: (0870) 7300800  FAX: (0870) 7300801 INTERNET: www.visonic.com VISONIC LTD. 2008 PowerMaxComplete USER GUIDE     D-300886  (Preparation for Rev. 2, 6/08)    (UL file:BP9249)

Navigation menu