Vista Imaging Vr6 Users Manual 8
VR6 to the manual b3161cfb-e406-55b4-95fa-4802bb136aeb
2015-02-06
: Vista-Imaging Vista-Imaging-Vr6-Users-Manual-457246 vista-imaging-vr6-users-manual-457246 vista-imaging pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
VR6 - VR8 In-Ceiling Speaker INSTALLATION INSTRUCTIONS: INSTALL Tools Needed: Pencil Keyhole or Drywall saw Phillips screwdriver Small level Fish tape or a coat hanger Wire strippers Gloves Safety goggles Drill 1” Flat bit (if driving through studs ½” or ½” bit for test hole) Figure A: Mark cutout area 1: Decide where you want to place your speakers. The speakers should be separated approximately 6 to 10 feet apart. If possible, the left and right speakers should be located the same distance from the listening position. If needed, the pivoting tweeter on the VR6 and VR8 can be directed towards the listener for improved sound quality. 2: Make sure the place you choose for your in-ceiling speakers is between the ceiling joists (preferably centered). Tap the ceiling for a hollow sound or use a stud finder to locate the studs. 3: Trace around the cardboard template for your speaker placement as shown in Figure A. Make sure the speakers are even and level. 4: Drill Hole, Insert Coat Hanger Figure B: Check for clearances Drill a small hole in the center outline you just traced. 5: Bend a piece of coat hanger wire. Insert the wire into the hole, then slowly rotate to check for any obstructions. If there are any obstructions, patch the hole and relocate the speaker. See figure B. 6: Carefully cut away the outline you traced using a keyhole or drywall saw. Then remove the cutout. See figure C. 7: Run the cable from the speaker outputs of your receiver or amplifier to your speakers. Allow a few extra feet of cable. You may also splice together lengths of cable if you have a long distance to cover. Leave enough cable slack to strip the conductors and work on the connections. Note: If cable is to be run through walls or ceilings, the cable must be UL and CL rated for your safety and building code compliance. VISTA ACOUSTICS VR6-VR8 OWNER’S MANUAL Figure C: Cut speaker hole 8: (Optional): Speaker performance can be enhanced by insulating the cavity with fiberglass insulation. When installing speakers in a ceiling, it is best to install a sheet of fiberglass insulation behind and around the back of the speaker. 9: Pull the cable slack through the hole in the ceiling and strip off the outer jacket. Strip about ½” of insulation off the ends of the wires. Connect the positive wire from the amplifier to the red terminal on the speaker. Connect the negative wire to the black terminal on the speaker. Note: Make sure the power is turned off on your amplifier or receiver before connecting the speakers. 10: Remove the speaker grill using provided tool. Place the speaker into the cutout in the ceiling. See figure D. Figure D: Install the speaker 11: Tighten the dogleg mounting screws evenly until the speaker is flat against the ceiling. If you are using a drill to tighten the screws, be sure to set the drill to its lowest torque setting. 12: Make the final adjustments to the pivoting tweeter and reinsert the grill into the speaker baffle. GRILL AND TRIM PAINTING INSTRUCTIONS: VR6 - VR8 SPECIFICATIONS: Mounting Depth Mounting Cutout Overall Diameter Power Handling Frequency Response Nominal Impedance Crossover Slope Pivoting Tweeter VR6 VR8 2.85 in - 75mm 7.6 in - 198mm 9.0 in - 235mm 3.25 in - 85mm 9.35 in - 244mm 10.7 in - 279mm 60 Watts 80Hz to 20kHz 8 ohm 12dB Acoustical 20mm Silk Dome 80 Watts 70Hz to 20kHz 8 ohm 12dB Acoustical 20mm Silk Dome Specifications subject to change. 1. Don’t paint speakers while installed. Be sure they are removed. 2. Remove the grill and paint seperately with two light coats. 3. Using scissors cut out the paint shield template provided with speakers. Place paint shield over the speaker area, so no paint will get on the cone or tweeter. Paint the trim using same method as the grill. WWW.VISTAACOUSTICS.CA Vista Acoustics® warrants to the original purchaser of this product that should the product or any part thereof be proven defective in material or workmanship within a period of 1 year from date of purchase by original purchaser, such defects will be repaired or replaced, at the Company’s option, without charge for parts or labor. THIS WARRANTY DOES NOT APPLY TO ANY PRODUCT OR PART THEREOF WHICH HAS BEEN DAMAGED THROUGH ALTERATION, MISHANDLING, MISUSE, NEGLECT, ACCIDENT, IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR.THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN CONTRACT OR TORT, WHETHER OR NOT ARISING FROM THE COMPANY’S NEGLIGENCE, ACTUAL OR IMPUTED. NO PERSON OR REPRESENTATIVE IS AUTHORIZED TO ASSUME FOR THE COMPANY ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. IN NO EVENT SHALL COMPANY BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. VISTA ACOUSTICS VR6-VR8 OWNER’S MANUAL
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Page Count : 2 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:ecaf4ae8-3246-4728-8849-f47ac6f9d75f Create Date : 2005:07:18 22:54:19Z Metadata Date : 2005:07:21 13:30:28-07:00 Modify Date : 2005:07:21 13:30:28-07:00 Creator Tool : Adobe InDesign CS (3.0) Rendition Class : proof:pdf Derived From Instance ID : 4259a21c-691d-11d9-9e06-b9387631d4b5 Derived From Document ID : adobe:docid:indd:4259a21b-691d-11d9-9e06-b9387631d4b5 Document ID : adobe:docid:indd:8c856c51-f819-11d9-92fb-87d115d4bbfe Format : application/pdf Title : VR6-8 Manual.indd Trapped : False Creator : Adobe InDesign CS (3.0) Producer : Adobe PDF Library 6.0EXIF Metadata provided by EXIF.tools