Vivint DW02 Security Signaling Equipment User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2437221
Application ID	SySStUYCHXyl7SnNaL1t/Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.52kB (256482 bits)
Date Submitted	2014-11-06 00:00:00
Date Available	2014-11-06 00:00:00
Creation Date	2017-10-20 16:03:32
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-20 16:03:32
Document Title	Users Manual
Document Creator	Acrobat PDFMaker 11 for Word

PRINT INSTRUCTIONS: REFERENCE SHEET V-DW11-345 P/N 77-000002-001 REV 1.1 |
INK: BLACK | MATERIAL: 20 LB MEAD BOND | SIZE: 5.50" X 8.50" SCALE 1:1 |
FOLDS: TRI-FOLD VERTICAL, TRI-FOLD HORIZONTAL (TO FIT IN BOX)
Door/Window Contact
(V-DW11-345)
Quick Reference
The Vivint Door/Window Contact (DW11) is a sensor device that can be installed
on doors, windows, and other objects in order to monitor open and closed states.
The DW11 transmits a signal to the panel when the magnet is moved away from,
or close to, the DW11 sensor.
The DW11 device has an external input for NC (Normally Closed) dry contact
devices, or it can be used with the supplied magnet directly with the sensor.
The DW11 is also equipped with a cover tamper for additional security.
Programming Instructions
(For more details, go to the Support page at: Vivint.com, and the KIM site at: corp.vivint.com/sites/KIM/)
• Loop 1: Use when the external input is used.
• Loop 2 (default): Use when the magnet is used directly with the sensor.
Installation Instructions
For internal switch usage:
1. Secure the sensor to the door or window frame, or other object, using
the supplied adhesive or screws.
NOTE: It is recommended to install the sensor on the side that
will be moving less (e.g. the doorframe instead of the door).
2. Secure the included magnet adjacent to the sensor on the door,
window, or other object using the supplied adhesive or screws.
NOTE: If necessary, use the supplied magnet spacer to better align the
magnet and sensor. Remove the back from the magnet using a small
flathead screwdriver and replace it with the spacer back.
For external switch usage:
1. Secure the external contact switch in the desired location.
2. If necessary, drill a hole to allow the external contact wires to reach
the desired location of the sensor.
3. Feed the wires through the drilled hole and then through the access
hole in the back of the sensor.
4. Connect the wires into the NC dry contact connector.
NOTE: With solid-core wire you should be able to push the wire
directly into the connector. Press the small button on the connector to
release the wire.
5. Mount the sensor in the desired location and reattach the sensor cover
(store excess wire in the device).
Installer Test
Once installed, open and/or close the door or window for which the DW11 is installed so that the sensor will
transmit to the Vivint Control Panel while the panel is in installer test mode.
User Test
Open and/or close the door or window for which the DW11 is installed to ensure the sensor is transmitting
correctly to the panel. The panel should recognize the state change of the object that is being monitored.
Specifications
Wireless Signal Range
Battery
Transmitter Frequency
Code Outputs
Supervisory Interval
Operating Temperature Limits
Relative Humidity
350 feet (106.7 m), open air
Panasonic CR2032 or equivalent lithium battery
345 MHz
Open, Close, Tamper, Low Battery, Loss of Supervision
70 minutes per signal (12 hours for panel to report supervision failure)
32° to 120°F (0° to 49°C)
5-95% Non-Condensing
Battery Installation
To replace battery, insert coin into the top slot and gently twist until the cover releases. Use only the recommended
replacement batteries (see Specifications).
WARNING! The polarity of the battery must be observed (as shown in the image). Improper handling of lithium
batteries may result in heat generation, explosion, or fire, which may lead to personal injury. Replace only with
the same or equivalent battery type as recommended by the manufacturer.
AVERTISSEMENT! La polarité de la batterie doit être observée (comme indiqué dans l'image). Une mauvaise
manipulation des piles au lithium peut conduire à la production de chaleur, une explosion ou un incendie, ce qui
peut entraîner des blessures. Remplacez-le par le même type ou équivalent de la batterie tel que recommandé
par le fabricant.
Batteries must not be recharged, disassembled or disposed of in fire. Disposal of used batteries must be made in accordance
with the waste recovery and recycling regulations in your area. Keep away from small children. If batteries are swallowed,
promptly see a doctor.
California Only: Perchlorate material special handling may apply. (For more information, visit:
www.dtsc.ca.gov/hazardouswaste/perchlorate)
Wireless Product Notice
Wireless communications hardware provides reliable communication; however, there are limitations which must be observed.
• The transmitters are required to comply with all applicable wireless rules and regulations. As such, they have limited
transmitter power and limited range.
• Wireless signals may be blocked by radio signals that occur on or near their operating frequencies.
FCC and Industry Canada Regulatory Declarations*
CAUTION: Unauthorized changes or modifications could void the user’s authority to operate the equipment.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
PRUDENCE! Changements ou modifications pourraient annuler le droit de l'utilisateur à utiliser l'équipement non autorisées.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal
(ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement
génère, utilise et peut émettre une énergie de radiofréquence et, s'il n'est pas installé et utilisé conformément aux instructions, il peut causer des
interférences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des interférences no se produiront pas dans une
installation particulière. Si cet équipement provoque des interférences nuisibles à la réception radio ou télévision, ce qui peut être déterminé en
mettant l'équipement hors et sous tension, l'utilisateur est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes:
• Réorienter ou déplacer l'antenne de réception.
• Augmentez la distance entre l'équipement et le récepteur.
• Connecter l'équipement à une sortie sur un circuit différent de celui sur lequel le récepteur est branché.
Consulter le revendeur ou un technicien radio / télévision expérimenté pour de l'aide.
FCC ID: 2AAAS-DW02
IC ID: 10941A-DW02
*For more compliance and warranty information, visit: www.vivint.com
© 2014 Vivint Inc. All Rights Reserved. | www.vivint.com | M/N: DW02 | Doc P/N: 77-000002-001 Rev. 1.1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Author                          : 
Create Date                     : 2014:09:26 17:58:55-06:00
Modify Date                     : 2014:10:01 22:09:12-06:00
Language                        : EN-US
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2014:10:01 22:09:12-06:00
Creator Tool                    : Acrobat PDFMaker 11 for Word
Document ID                     : uuid:344fd1ac-b098-4645-8bfb-b3fba06a6226
Instance ID                     : uuid:5aaa9ba9-a190-479b-bc4a-95c1a4cba744
Format                          : application/pdf
Title                           : 
Creator                         : 
Producer                        : Adobe PDF Library 11.0
Page Layout                     : OneColumn
Page Count                      : 2

EXIF Metadata provided by EXIF.tools