Vivint PB01 Personal Emergency Indicator User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2474266
Application ID	1RSkjXY+g3Q8FMGvhxneIw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	29.88kB (373445 bits)
Date Submitted	2014-12-16 00:00:00
Date Available	2014-12-16 00:00:00
Creation Date	2017-10-20 03:50:48
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-20 03:50:48
Document Title	Users Manual
Document Creator	Acrobat PDFMaker 11 for Word

PRINT INSTRUCTIONS: REFERENCE SHEET V-PANIC2-345 P/N 77-000020-001 REV 1.1 |
INK: BLACK | MATERIAL: 20 LB MEAD BOND | SIZE: 5.50" X 8.50" SCALE 1:1 |
FOLDS: TRI-FOLD VERTICAL, TRI-FOLD HORIZONTAL (TO FIT IN BOX)
Panic Button Remote
(V-PANIC2-345)
Quick Reference
The Vivint Panic Button Remote (PANIC2) is designed to transmit an
emergency signal from any location within range of the control panel.
The panel will receive signals whether the system is armed or disarmed.
The PANIC2 device is discrete and versatile. It is small and lightweight
enough to be stored in a pocket or purse. Additionally, the supplied
accessories allow the device to be worn on a lanyard, wristband, or belt
clip/holder; or placed in the holder that can be mounted in a fixed
location (see accessory drawings).
Programming Instructions
(For more details, go to the Support page at: Vivint.com, and the KIM site at: corp.vivint.com/sites/KIM/)
• The PANIC2 device can be programmed as a supervised or non-supervised device. If supervised, the
device should always stay within range of the panel.
• The device can be programmed to contact emergency services with either an audible or silent alarm.
Accessories
Use the supplied accessories to carry or mount the PANIC2 device.
Installer Test
Press and hold the button for 2 seconds to send signals from the device to the control panel.
Specifications
Wireless Signal Range
Battery
Battery Life
Transmitter Frequency
Code Outputs
Supervisory Interval
Operating Temperature Limits
Relative Humidity
300 feet (91.4 m), open air
Panasonic CR2032 or equivalent lithium battery
3-5 years under normal usage
345 MHz
Alarm, Alarm Restore, Supervisory, Low Battery
70 minutes per signal (12 hours for panel to report supervision failure)
32° to 120°F (0° to 49°C)
5-95% Non-Condensing
Battery Installation
The battery should last 3-5 years under normal use. If the battery is low, a low battery
notification will be indicated on the control panel. To replace the battery,
1. Remove the cover by inserting a coin in the slot and twisting gently.
2. Place a small flathead screwdriver in the slot between the metal clip and battery
and pry the battery up and out of the battery holder.
3. Insert the replacement battery with the + sign facing out.*
4. Replace the sensor cover.
5. Verify the device is functioning properly.
*The battery may fit loose in the battery holder, but the cover will hold it securely in place.
WARNING! The polarity of the battery must be observed (as shown in the image). Improper handling of lithium batteries may result
in heat generation, explosion, or fire, which may lead to personal injury. Replace only with the same or equivalent battery type as
recommended by the manufacturer.
AVERTISSEMENT! La polarité de la batterie doit être observée (comme indiqué dans l'image). Une mauvaise manipulation des piles
au lithium peut conduire à la production de chaleur, une explosion ou un incendie, ce qui peut entraîner des blessures. Remplacez-le
par le même type ou équivalent de la batterie tel que recommandé par le fabricant.
Batteries must not be recharged, disassembled or disposed of in fire. Disposal of used batteries must be made in accordance with the waste
recovery and recycling regulations in your area.
Keep away from small children. If batteries are swallowed, promptly see a doctor.
California Only: This Perchlorate warning applies ONLY to Manganese Dioxide Lithium cells sold or distributed in California, USA. Perchlorate material
special handling may apply. (For more information, visit: www.dtsc.ca.gov/hazardouswaste/perchlorate)
Wireless Product Notice
Wireless communications hardware provides reliable communication; however, there are limitations which must be observed.
• The transmitters are required to comply with all applicable wireless rules and regulations. As such, they have limited
transmitter power and limited range.
• Wireless signals may be blocked by radio signals that occur on or near the wireless operating frequencies.
FCC and Industry Canada Regulatory Declarations*
CAUTION: Unauthorized changes or modifications could void the user’s authority to operate the equipment.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules and Industry Canada (IC)
license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
PRUDENCE: Changements ou modifications pourraient annuler le droit de l'utilisateur à utiliser l'équipement non autorisées.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal
(ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement
génère, utilise et peut émettre une énergie de radiofréquence et, s'il n'est pas installé et utilisé conformément aux instructions, il peut causer des
interférences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des interférences no se produiront pas dans une
installation particulière. Si cet équipement provoque des interférences nuisibles à la réception radio ou télévision, ce qui peut être déterminé en
mettant l'équipement hors et sous tension, l'utilisateur est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes:
• Réorienter ou déplacer l'antenne de réception.
• Augmentez la distance entre l'équipement et le récepteur.
•
Connecter l'équipement à une sortie sur un circuit différent de celui sur lequel le récepteur est branché.
•
Consulter le revendeur ou un technicien radio / télévision expérimenté pour de l'aide.
FCC ID: 2AAAS-PB01 , IC ID: 10941A-PB01
*For more compliance and warranty information, visit: www.vivint.com
© 2014 Vivint Inc. All Rights Reserved. | www.vivint.com | M/N: PB01 | Doc P/N: 77-000020-001 Rev. 1.1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Author                          : 
Create Date                     : 2014:09:29 18:00:00-06:00
Modify Date                     : 2014:10:01 22:10:31-06:00
Language                        : EN-US
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2014:10:01 22:10:31-06:00
Creator Tool                    : Acrobat PDFMaker 11 for Word
Document ID                     : uuid:57209d2c-4e76-487f-8a11-d22fd8edee84
Instance ID                     : uuid:ec44d8da-d41f-42c4-aec7-ad6b04705eb1
Format                          : application/pdf
Title                           : 
Creator                         : 
Producer                        : Adobe PDF Library 11.0
Page Layout                     : OneColumn
Page Count                      : 2

EXIF Metadata provided by EXIF.tools