Von Duprin 5100 Elec Strike 107665

User Manual: Von Duprin 5100 Elec Strike Installation Instructions

Open the PDF directly: View PDF PDF.
Page Count: 4

*931029-00*
931029-00
4-7/8”
Standard ANSI,
Sharp Corner
7-15/16” Long,
Round Corner
Figure 3
Fail-safe (FS) Mode Fail-secure (FSE) Mode
ActuatorActuator
Figure 2
Backbox cover
3. Prepare frame for strike (see page 4 for dimensions).
Note: Prepare room for RCP rectifier if needed.
4. Make sure strike operates in correct mode. Lip of fail-safe (FS) strike can be moved when strike is not powered. Lip of
fail-secure (FSE) strike cannot be moved when strike is not powered. If necessary, remove backbox cover (Figure 2) and
change strike mode by repositioning actuator (Figure 3).
1.
For lock preparation, see lock instructions.
2.
Install correct faceplate onto strike (Figure 1).
Figure 1
Wiring must
stay in slot
4-7/8”
Standard ANSI,
Round Corner
#10-24 flat head
nyloc screws
When using the electric strike in fail-secure mode, the local
authority having jurisdiction shall be consulted to assure
compliance in allowing emergency exit from the secured area.
NOTE
!
Electric Strike
5100
Installation Instructions
Page 2 of 4
Figure 5
12 VDC input
nonpolarized
Red
Red-White
Black
Black-White
Figure 4
24 VDC input
nonpolarized
Red
Black
Red-White
Black-White
12 VDC, 0.38 A
24 VDC, 0.19 A
SOLENOID POWER
REQUIREMENTS
tuptuo CDV 21tupni CAV 2
1
tuptuo CDV 42tupni CAV 42
White
White
Yellow for 12 V
Red for 24 V
Black
SO kit
ForDC operation, Von Duprin PS 861 and
Locknetics 593 DC series power supplies
are recommended.
ForAC operation, Von Duprin SO-12 or 24
AC/DC convertor kit (shown below)
is recommended.
12 VDC Strike Wiring
24 VDC Strike Wiring
5.
Check power source voltage (12 or 24 VAC or VDC).
6. When using 12 VAC or 24 VAC power, install SO kit to convert AC power to DC (Figure 4).
7. Wire strike solenoid for proper voltage (Figure 5). Caution: Do not connect 24 VDC to 12 VDC configured strike.
8. Test strike: Apply solenoid power. Fail secure (FSE) lip unlocks. Fail safe (FS) lip locks.
9. If cut-out for strike is too large along edge (Figure 6), cut neoprene filler and stick onto strike as shown (Figure 7).
Note: This could occur in some retrofit applications.
Neoprene filler
Cut to length and
stick on strike
Figure 6Figure 7
Gap filled
5/8” Maximum
latch bolt
projection
Figure 9
Top view;
faceplate not
shown for clarity
1/32”
Strike
lip
Door
Figure 10
Backbox
Faceplate
screws (2)
Backbox
screws (2)
Adjust Strike Lip
Remove two Phillips head
faceplate screws and remove
faceplate.
Loosen two Hex head
backbox screws and
move backbox
sideways as necessary,
then secure screws.
Replace faceplate
and secure faceplate
screws.
A
B
C
Page 3 of 4
11.Install strike with two #12-24 mounting screws. Make sure clearance between latch bolt and strike lip is 1/32” (Figure 9).
If not, remove strike, adjust (Figure 10), and reinstall.
10.
If frame does not have built in mounting tabs, install mounting tabs supplied with strike as shown below (Figure 8).
Attach mounting tabs to
strike with two #12-24
screws and mark 4
mounting tab holes on
frame as shown below.
ABDrill four
mounting holes.
CMount the two
mounting tabs inside
frame using #10-24
screws as shown below.
DShim strike in or out as
needed until faceplate is
flush with frame.
Frame too thick
Add shim(s)
between tabs
and strike
Frame too thin
Add shim(s)
between tabs
and frame
Shim
Shim
Figure 8
Mounting
tabs
1/4” thru hole
countersunk for
#10-24 flat head
screw, 4 places
12.Test door: With strike unlocked, door opens with latch bolt extended. When door closes, latch bolt rides over strike lip
and relatches.
Shim
Mounting
tab
Mounting
tab
Flush
Flush
© Allegion 2014
Printed in U.S.A.
931029-00 Rev. 01/14-c
Customer Service
1-877-671-7011 www.allegion.com
Strike Dimensions
Suggested
cut-out
LHR shown
RHR opposite
5/32” radius
on 4 corners
Metal: #16 drill
and #12-24 tap
2 places
Wood: 1/8” drill
pilot hole
3/4” deep
2 places
Short Faceplate Suggested Cut-outLong Faceplate Suggested Cut-out
L
C lock and strike
31/32”
4-1/8”
4-7/8”
5/8”
2-7/16”
1-1/4”
2-1/16”
C strike
L
1-1/2”
1-11/16”
5/32” radius
on 4 corners
(Aluminum frame)
1-11/16”
3-3/8”
3/32”
1-1/16”
1”
31/32”
7-15/16”
23/32”
3-31/32”
1-7/16”
5/32” radius
on 4 corners
C lock and strike
L
7-7/16”
3-23/32”
Reinforce for
strike attachment
as required
LHR shown
RHR
opposite
5/32” radius
on 4 corners
(Aluminum frame)
#16 drill and
#12-24 tap
2 places
Suggested
cut-out

Navigation menu