Voxx Accessories MOD1 Smart module User Manual 2 of 3

Voxx Accessories Corp. Smart module 2 of 3

Contents

User manual 2 of 3

Smart Module Mounting TemplateControl Unit Mounting templateDrywall screwsSMART Laundry Shut Off SystemDIY Quickstart GuideThe control unit needs to be close enough to the shut-off valves and oor for the sensor wire (6ft) and control lead wires (5ft) to reach. The smart module should be between the control unit and the shut-off valves. It also needs to be close to a power outlet.There are three mounting options: - Double-sided tape (included, not for masonry applica-tions)- Drywall screws with anchors (included), using the mount-ing template (included)- Masonry screws (included), using the mounting template (included)Off Turn each valve 90-degrees counter-clockwise to turn it off. Place a bucket and towels under the shut-off valves before you remove the hoses. Remove the plastic protectors from both ends of each automatic shut-off valve. Make sure the rubber o-rings are seated properly (at) inside each hose tting.Match the red automatic shut-off valve (HOT) to the red valve and the blue (COLD) to the blue valve.Screw each hose tting onto the automatic shut-off valves. Hand-tighten the collar of the tting onto the washer shut-off valve (use a channel lock or pliers for the last quarter-turn).Make sure each laundry hose still has its o-ring inside the hose tting. If it doesn’t, use one of the extra o-rings provided in this package. Match each hose to the shut-off valve it was on before. Then screw each hose on tight by hand (use a channel lock or pliers for the last quarter-turn).Continues on back...Masonry screws45mm(1.77")72mm(2.83")MOUNTING TEMPLATEUSE FOR FLATWALL MOUNT ONLYFOR THE CONTROL UNITLess than 5ftLess than 6ftControl unitFloorShut-off valvesPower outletSmart moduleIMPORTANT: The smart module needs a strong signal from your WiFi router to work properly. Test the strength of your WiFi network’s signal where you plan to mount the smart module—make sure your phone is on the WiFi network you want to use, then look at the WiFi signal meter on your phone’s screen. Make sure you’re getting at least 50% signal strength where you plan to install. If not, try moving your WiFi router closer (or installing a WiFi signal booster close to the installation).The back and side of the smart module list its MAC address. You’ll need this to add the module to the App and your WiFi network later on, so you should nd it and write it down now, before you mount the smart module to the wall.Smart module, back and sideSmart Module MAC Address:________________________MOUNTING TEMPLATEUSE FOR FLATWALL MOUNT ONLY( 2 ")( 3.45")( 2.36")50.8mm87.5mm60.0mmControlBoxShut-Off ValvesSmartModuleControlBoxShut-Off ValvesSmartModuleControlBoxShut-Off ValvesSmartModuleControlBoxShut-Off ValvesSmartModuleDC InA. Connect the lead from one shut-off valve to a control box lead.B. Connect the second control box lead to the rst lead from the smart module.C. Connect the middle lead from the smart module to the other shut-off valve.D. Connect the third cord from the smart module to the DC In jack on the control box.How to connect leads1. Line up the round and square plugs on each control box lead to the corresponding round and square holes on the lead from the auto shut-off boxes. 2. Snap both pairs of leads into place.Use the included wire ties to gather the wires and stick them to the wall so that they’re out of the way.Clean the wall rst. Then stick the back of the wire tie to the wall. Use the other wire tie closer to the control box to gather the wires there as well.Agua detectadaMake sure the sensor is sitting at on the oor directly beneath the shutoff valves. (Do not place it inside the washer oor tray if you have one.) Plug the smart module’s power adapter into the jack on the side of the smart module. Plug the other end of the power adapter into an available power outlet. If both power outlets are in use (by the washer and dryer, for example), use the included 3-outlet power wall tap to provide additional outlets. When the smart module and control unit rst power on, the yellow indicator light on the front panel of the control unit ashes—the auto shut off valve system is arming and opening valves. When the green indicator light comes on, the system is ready to use.3-outlet power wall tapFor detailed instructions, see the Installation Guide.Find the best place to mount the control unit and smart module.Write down the smart module’s MAC address.Mount the control unit and smart module to your wall.Turn off your washer’s shut-off valves and remove the washer hoses from the valves.Install the automatic shut-off valves on the washer shut-off valves.1 2 435Screw the hoses onto each automatic shut-off valve.6Connect the control box, smart module, and shut-off valves.7Place the leak sensor on the oor beneath the washer shutoff valves.8Plug in the smart module.9Rating LABEL2018/03/27MODI-IOT67630551460G A0.1YangZhiQiang条码读码为: 70F8E7262881 此号码为16进制,每张标签之间需跳一码,即第一张号码为70F8E7262881,则第二 张号码为70F8E7262883,.....此次流水号为 此次流水号为GMA252V13F0001~GMA252V13F010070F8E7262881~70F8E7262947,共100张.MAC NUMBERMACSN: GMA252V13F0001: 70F8E7262881SMART MODULEMADE IN CHINACAN ICES-3(B)/NMB-3(B)FCC ID: VIXMOD1IC: 21578-MOD1MODEL: MOD1INPUT: 12V 1A30.0mm36.0mm条码读码为: GMA252V13F0001Serial numberF: GMA25:Model code(MOD1-IOT)Assigned by AECV: Manufactured year(V=2018,skip I,O,S,Z)13: Manufactured week2TO: 采购2018.03.27
Using the auto shut-offWhen the alarm goes off...If the sensor senses water, the alarm sounds and the valves close. The yellow and red indicators on the control box start ashing. You will also receive a notication on your phone saying “Device has been triggered. Automatic shut-off activated.”Once you’ve xed the leak and dried off the sensor...Press and release the Test/Reset button on the control unit. The yellow light ashes while the valves are reopening. The green light comes on when they have nished reopening.Losing powerIf you lose power, the control box automatically closes the shut off valves (more slowly than during a real alarm), then powers off. You will also get a notication on your phone saying “Device Disconnected.” When power returns, if the sensor does not detect water, the control box will open the valves again.Turn the laundry shut off valves 90 degrees clockwise to turn the water supply on for both hoses. Make sure there are no leaks. If there are leaks, tighten the hose ttings.Press and release the Test/Reset button on the control unit. NOTE: Press the Alarm Off button immediately after to mute the sound.The system’s alarm goes off, the automatic valves close, and the yellow indicator on control unit starts ashing.You will also receive a notication from the RCA Water Shut-Off App (“TEST” will appear on your screen).Once the valves are completely closed, the control unit will automatically re-open them again in about 30 seconds. The yellow light ashes while the valves are reopening. The green light comes on when they have nished reopening. The test process takes about 25 seconds to complete and return to normal (valves open and green light) status. If the green light doesn’t come back on, unplug the controller and plug it back in. Then test the system again.RSWL1 QSG 01Customizing the alarmBy default, the audible alarm keeps sounding until you turn it off (or until the sensor no longer senses water). You can also set the audible alarm to sound for 10 seconds only. To change the audible alarm to 10 seconds only: Press and hold the Alarm Off button for 2-3 seconds. The yellow LED ashes to show that you’ve changed the audible alarm to 10 seconds only. To change back, press and hold the Alarm Off button again.A. Download and install the App on your phone.Search for “RCA Water Shut-Off” in the Apple App or Google Play Stores. Look for the icon shown here and install this App on your phone. IMPORTANT!!!• Make sure your phone is on the WiFi network you want the Smart Water Shut-Off system to use.• If you have a dual-band router that uses different networks for the two bands, make sure the WiFi signal you use is 2.4GHz, not 5GHz!• Make sure your Smart Module is ready for setup!The Link and Activity indicators on the Smart Module are on when the Smart Module is in Setup mode. The Smart Module goes into Setup Mode automatically when you rst power it up and stays in Setup Mode for 6 minutes. If the Link and Activity indicators on the Smart Module are not on, unplug the Smart Module and plug it in again.Shut-off valvesOn OffTo stop the audible alarm: On the control unit, press the Alarm Off button. (The valves will still be closed.)Vacation ModeIf you plan to be away from home for an extended period, put the system in Vacation Mode to shut the valves while you’re gone. Simply press and hold the Test/Reset button for three seconds. The yellow indicator light blinks while the valves are closing and turns solid yellow with the valves are closed.When you get back, press and release the Test/Reset button again to open the valves. The yellow indicator light blinks while the valves are opening; the green indicator comes on when the valves are open.App Notications GuideIf your phone says... This means...“Device has been triggered. Automatic shut-off activated.”Your sensor has detected water and automatically shut valves.“TEST” Your system has gone through a test and will re-open valves when nished.“Device connected” Your system has regained power and re-opened valves.“Device disconnected” Your system has lost power and automatically shut valves.“Device has re-connected to WiFi” Your smart module lost its WiFi connection but is now re-connected.Set up the App with your system.10 Turn on the water supply.11Test the system.12B. Launch the App The rst time you open the App, you’ll be asked if you want to allow the RCA Water Shut-Off App to send you notications. Make sure you choose Allow in this step so that the App can notify you when needed!Make sure your Smart Module is ready for setup!If the Link and Activity indicators on the Smart Module are not on, unplug the Smart Module and plug it in again.Make sure you’re on the WiFi network you want to use!If the Network Name doesn’t match the network you want to use, quit the App, go to the network settings for your phone, and connect to the network you want to use. Then start the App again.C. Connect the App to your WiFi networkPress the Remember Password and Show Password boxes so that you only have to enter your password once (and you can see it while you’re entering).Enter the password for your WiFi network. Then press OK. IMPORTANT: Double check your network name and password—these must be correct to work with the App!D. Connect the App to your Smart ModuleOnce you’ve entered the information for your WiFi network, the App starts searching for your Smart Module. When the App’s search screen displays “Found devices” you can press Cancel to stop the search. NOTE: If you’re connecting multiple Smart Modules, wait for the search timer to complete its search.C. Connect the App to your WiFi network (continued) E. Conrm your Smart Module is connected and select it Your Smart Module should be listed in the devices available in the next screen. The Link indicator on its front panel goes solid and the Activity indicator starts blinking.Choose the Smart Module you want to use from the list that appears (check the MAC The App nishes setting up the Smart Module with your WiFi network and displays a sample alert to verify that it’s up and running. In this alert screen, you have the following options: accesses your phone’s alert settings so that you can modify the App’s permissions.Edit name lets you choose a different name for your system in the alert screens. You can choose one of the preset names or create your own. accesses your notication history, which shows all of the times the App has sent alerts and what those alerts were.Unselect removes this Smart Module from alerts. (You’ll have to re-select it again.)Congure accesses other setup options. Search looks for Smart Modules in your WiFi network.Done exits the screen.address shown against the MAC address you wrote down earlier). Press the Select button next to the Smart Module you want to add. Then press Next at the bottom of the screen. Questions? Please call our toll-free customer service hotline at 1-800-645-7750

Navigation menu